Re-assembly behaviors of polystyrene-b-poly(acrylic acid) micelles

The re-assembly behaviors of spherical micelles of the polystyrene-b-poly(acrylic acid) (PS-b-PAA) diblock copolymer in different solvent mixtures were investigated using dynamic light scattering, transmission electron microscopy and atomic force microscopy. Depending on the nature of the solvent, PS-b-PAA micelles re-assembled from spheres to nanorings in toluene or to necklace-like aggregates in water induced by solvent evaporation. Systematic studies suggested that the re-assembly behaviors on a neutral surface are strongly correlated with the micellar surface components, the solvent polarity and the chain length of the micelle corona of the solvated blocks. We proposed that the formation of nanorings from PS-b-PAA micelles in toluene is mainly induced by the dewetting process of the solvent, while the necklace-like structure arises from the hydrogen bonding interactions among the partially dissociated PAA units.     

Orientational order and mechanical properties of poly(amide-block-aramid) alternating block copolymer films and fibers

Mechanical properties and orientational order of a series of uniaxially oriented block copolymer films and fibers comprised of alternating rigid aramid blocks of poly(p-phenylene terephthalamide) (PPTA) and flexible blocks of polyamide 6,6 (PA 6,6) have been investigated. The prepared block copolymer films differ in aramid content and average block length. The films were prepared by shearing the polymer solutions (in sulphuric acid) followed by rapid coagulation of the solutions in water. From wide angle X-ray scattering (WAXS) and optical polarisation microscopy (OPM) it was found that films with a mole fraction of PPTA of at least 0.5 show a liquid crystalline (LC) phase. It was found that the mechanical properties of LC block copolymer films are similar to the properties of isotropic films, as determined with dynamical mechanical analyses (DMAs) and from tensile tests. This was attributed to the relative low parameter of the LC films obtained by using WAXS. Copolymerisation of the PPTA blocks with the flexible polyamide blocks resulted in an increase of storage and Young's modulus, a decrease of the elongation at break while the tensile strength was unaffected compared to normal PA 6,6. Block copolymer fibers have been spun from liquid crystalline solutions by means of a dry-jet wet spinning process. The only variable parameter was the imposed draw-ratio in the air-gap of the spinning process. Increasing the draw-ratio resulted in an increased molecular orientation, Young's modulus and tensile strength of the fibers while its effect on the maximum elongation at break was small. Heat treatment at 300 °C of the fibers resulted in an increase of the Young's modulus, a minor increase of the strength and a decrease of the elongation at break. Scanning electron microscopic (SEM) photographs of the fractured surfaces of the block copolymer fibers do not show a fibrillar fracture surface, which is typically observed for pure PPTA fibers.     

Thermal behavior and properties of polystyrene/poly(methyl methacrylate) blends

The thermal behavior and properties of immiscible blends of polystyrene (PS) and poly(methyl methacrylate) (PMMA) with and without PS‐b‐PMMA diblock copolymer at different melt blending times were investigated by use of a differential scanning calorimeter. The weight fraction of PS in the blends ranged from 0.1 to 0.9. From the measured glass transition temperature (T_g) and specific heat increment (ΔC_p) at the T_g, the PMMA appeared to dissolve more in the PS phase than did the PS in the PMMA phase. The addition of a PS‐b‐PMMA diblock copolymer in the PS/PMMA blends slightly promoted the solubility of the PMMA in the PS and increased the interfacial adhesion between PS and PMMA phases during processing. The thermogravimetric analysis (TGA) showed that the presence of the PS‐b‐PMMA diblock copolymer in the PS/PMMA blends afforded protection against thermal degradation and improved their thermal stability. Also, it was found that the PS was more stable against thermal degradation than that of the PMMA over the entire heating range. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 609–620, 2004     

Syntheses of well-defined poly(siloxane)-b-poly(styrene) and poly(norbornene)-b-poly(styrene) block copolymers using functional alkoxyamines

Functional alkoxyamines, 1-[4-(4-lithiobutoxy)phenyl]-1-(2,2,6,6-tetramethylpiperidinyl-N-oxyl)ethane (2) and 1-[4-(2-vinyloxyethoxy)phenyl]-1-(2,2,6,6-tetramethylpiperidinyl-N-oxyl)ethane (3) were prepared, and well-defined poly(hexamethylcyclotrisiloxane)-b-poly(styrene)[poly(D₃)-b-poly(St)] and poly(norbornene)-b-poly(St) [poly(NBE)-b-poly(St)] were prepared using the alkoxyamines. The first step was preparation of poly(D₃) and poly(NBE) macroinitiators, which were obtained by the ring-opening anionic polymerization of D₃ using 2 as an initiator and the ring-opening metathesis polymerization of NBE using 3 as a chain transfer. The radical polymerization of St by the poly(D₃) and poly(NBE) macroinitiators proceeded in the ‘living’ fashion to give well-defined poly(D₃)-b-poly(St) and poly(NBE)-b-poly(St) block copolymers.     

Transition behavior and ionic conductivity of lithium perchlorate-doped polystyrene-b-poly(2-vinylpyridine)

We report the transition behavior and the ionic conductivity of ion-doped amorphous block copolymer, based on two compositionally different polystyrene-block-poly(2-vinylpyridine) copolymers (PS-b-P2VPs) that can self-assemble into nanostructures, where P2VP block is ionophilic to lithium perchlorate (LiClO₄). The transition temperatures of LiClO₄-doped PS-b-P2VP, like the order-to-disorder transition (T_ODT), were measured by small-angle X-ray scattering (SAXS) and depolarized light scattering (DPLS). The selective ionic coordination to the nitrogen units of P2VP block leads to the increase of the repulsive interactions between two block components from weak- to strong-segregation regime with increasing amount of LiClO₄, which results subsequently in the increased T_ODT. However, for a compositionally asymmetric PS-b-P2VP under lamellar morphology, the ionic conductivity by the addition of LiClO₄ was remarkably increased at higher temperatures, representing that the effective ionic coordination at the greater volume fraction of P2VP block component improves the ionic conductivity as the temperature approaches to a rubbery phase.     

Morphology of polystyrene/polystyrene-block-poly(methyl methacrylate)/poly(methyl methacrylate) composite particles

Polystyrene/polystyrene-block-poly(methyl methacrylate)/poly(methyl methacrylate) (PS/PS-b-PMMA/PMMA) composite particles were prepared by releasing toluene from PS/PS-b-PMMA/PMMA/toluene droplets dispersed in a sodium dodecyl sulfate aqueous solution. The morphology of the composite particles was affected by release rate of toluene, the molecular weight of PS-b-PMMA, droplet size, and polymer composition. ‘Onion-like’ multilayered composite particles were prepared from toluene droplets of PS-b-PMMA and of PS/PS-b-PMMA/PMMA, in which the weights of PS and PMMA were the same. The layer thicknesses of the latter multilayered composite particles increased with an increase in the amount of the homopolymers. PS-b-PMMA/PS composite particles had a sea-islands structure, in which PMMA domains were dispersed in a PS matrix. On the other hand, PS-b-PMMA/PMMA composite particles had a cylinder-like structure consisting of a PMMA matrix and PS domains.     

Functionalization of amphiphilic coil-rod-coil triblock copolymer poly(2-vinylpyridine)-b-poly(n-hexyl isocyanate)-b-poly(2-vinylpyridine) with florescence moiety and C60

We recently achieved quantitative synthesis of an amphiphilic coil-rod-coil triblock copolymer, poly(2-vinylpyridine)-b-poly(n-hexyl isocyanate)-b-poly(2-vinylpyridine), by coupling in situ living diblock copolymer poly(2-vinylpyridine)-b-poly(n-hexyl isocyanate) (P2VP-b-PHIC) using malonyl chloride in the presence of pyridine. This led to the introduction of an active methylene group that is a site for further functionalization in the rod block. The Michael addition reaction of the triblock copolymer with 7-(4-trifluoromethyl) coumarin acrylamide led to copolymer bearing a fluorescent pendent in the rod block. The fluorescent labeled copolymers were isolated in ∼94% yields. Similarly C₆₀ pendent was introduced to the rod block by the Bingel reaction. The yields of C₆₀ functionalized copolymers were ∼54%. The precursor and functionalized amphiphilic coil-rod-coil copolymer show diverse morphologies, such as micelles and vesicles by simply changing the solvent. For the C₆₀ functionalized block copolymer, structural constraints in micelles and vesicles prevented C₆₀ pendents to aggregate.     

Multiple morphologies of a poly(methyl methacrylate)-block-poly(N,N-dimethyl aminoethyl methacrylate) copolymer with pH-responsiveness and thermoresponsiveness

We successfully prepared a series of pH-responsive and thermoresponsive poly(methyl methacrylate) (PMMA)-block-poly(N,N-dimethyl aminoethyl methacrylate (PDMAEMA) copolymers via reversible addition–fragmentation chain-transfer polymerization with PMMA as a macro chain-transfer agent. Control over the chain length of PDMAEMA allowed the morphological transformation of PMMA-b-PDMAEMA. The critical water content and critical micelle concentration also depended on the length of the PDMAEMA block. UV–visible and fluorescence spectrum analyses indicated that the PMMA-b-PDMAEMA copolymer exhibited a lower critical solution temperature type phase transition in water. The particle size of PMMA-b-PDMAEMA was dominated by the pH value, as evidenced by dynamic light scattering and transmission electron microscopy. In addition, the PMMA-b-PDMAEMA copolymers exhibited good reversible thermoresponsive behavior between 33 and 38°C. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47972.     

Preparation and properties of poly(ethylene glycol)-block-poly(acrylic acid)-coated cobalt nanocrystals

Reported in this paper are the preparation and properties of ?-Co nanocrystals coated by poly(ethylene glycol)-block-poly(acrylic acid) (PEG-b-PAA). These particles were prepared via the thermal decomposition of Co₂(CO)₈ at 185 °C in 1,2-dichlorobenzene, in the presence of the surfactant PEG-b-PAA and the co-surfactant trioctylphosphine oxide. At a given initial Co₂(CO)₈ concentration, the size of the particles increased with increasing Co₂(CO)₈-to-PEG-b-PAA molar ratio, and could be tuned between ∼5 and ∼20 nm. The size distribution of the particles narrowed as the Co₂(CO)₈ concentrations increased. The resultant particles were dispersible in a wide range of solvents, including chloroform, N,N-dimethylforamide, and water, which solubilized PEG. Magnetic measurements revealed that the particles possessed saturation magnetization close to that of bulk Co, suggesting high purity of the particles.     

Synthesis and analysis of phase segregation of polystyrene-block-poly(methyl methacrylate) copolymer obtained by Steglich esterification from semitelechelic blocks of polystyrene and poly(methyl methacrylate)

Here, an alternative route to successfully synthesize polystyrene-block-poly(methyl methacrylate) (PS-b-PMMA) is reported. Steglich esterification was used as an effective, metal free approach for coupling carboxylic terminated PS and the hydroxyl end-functionalized PMMA chains obtained by nitroxide-mediated polymerization and atom transfer radical polymerization, respectively. α-Functionalization was obtained using 4,4′-azobis(4-cyanovaleric acid) and 2,2,2-tribromoethanol as initiators. The synthesis of PS-b-PMMA was confirmed by gel permeation chromatography and nuclear magnetic resonance (NMR), while the dependence of the diffusion coefficients of the polymers (PS, PMMA, PS/PMMA blend, and PS-b-PMMA) with their corresponding molecular weights was discussed based on the results of atomic force microscopy-based infrared spectroscopy, differential scanning calorimetry, and spectra of diffusion-ordered NMR spectroscopy. Differently from PS-b-PMMA, a partial segregation was observed for the PS/PMMA blend, affecting its thermal behavior and diffusion coefficient. The study here presented provides an easier and efficient strategy for the synthesis of PS-b-PMMA and new insights into the diffusion of polymers.     

Physical properties of poly(cyclohexyl methacrylate)-b-poly(iso-butyl acrylate)-b-poly(cyclohexyl methacrylate) triblock copolymers synthesized by controlled radical polymerization

The microphase segregation of different poly(cyclohexyl methacrylate)-b-poly(iso-butyl acrylate)-b-poly(cyclohexyl methacrylate), PCH-b-PiBA-b-PCH, triblock copolymers obtained by atom transfer radical polymerization has been evaluated by dynamic mechanical thermal analysis through location of the two relaxations ascribed to cooperative motions of each block. Additionally, other secondary relaxations have been found, whose characteristics are also dependent on molecular weight of outer and rigid segments. The length of these hard blocks influences significantly the stiffness and microhardness found in these triblock copolymers. These two mechanical parameters increase as molecular weight of poly(cyclohexyl methacrylate) does. The morphological aspects have been examined by small angle X-ray scattering and atomic force microscopy.     

Solvent induced morphologies of poly(methyl methacrylate-b-ethylene oxide-b-methyl methacrylate) triblock copolymers synthesized by atom transfer radical polymerization

Poly(methyl methacrylate-b-ethylene oxide-b-methyl methacrylate) (PMMA-PEO-PMMA) triblock copolymers were synthesized using atom transfer radical polymerization (ATRP) and halogen exchange ATRP. PEO-based macroinitiators with molecular weight from M_n = 2000 to 35,800 g/mol were used to initiate the polymerization of MMA to obtain copolymers with molecular weight up to M_n = 82,000 g/mol and polydispersity index (PDI) less than 1.2. The macroinitiators and copolymers were characterized by gel permeation chromatography (GPC) and nuclear magnetic resonance (NMR) spectroscopy. The melting temperature and glass transition temperature of the copolymers were measured by differential scanning calorimetry (DSC). Crystallinities of the PEO blocks were determined from the WAXS patterns of both homopolymers and block copolymers, which revealed the fragmentation of PEO blocks due to the folding of the PMMA chains. Interestingly, the fragmentation was less pronounced when cast on surfaces compared to that in bulk, as measured by GISAXS. Solvent casting was used to control the morphology of the copolymers, permitting the formation of various states including amorphous, induced micellar with a PMMA core and flower-like PEO arms, and a cross-linked gel. Atomic force microscopy (AFM) was used to visualize the different copolymer morphologies, showing micellar and amorphous states.     

Analysis of poly(ethylene oxide)-b-poly(propylene oxide) block copolymers by MALDI-TOF mass spectrometry using collision induced dissociation

Matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOF-MS) was used to analyse the block length of commercially available block copolymers of poly(ethylene oxide) and poly(propylene oxide) (PEO-b-PPO) based on the fragmentation behaviour in collision induced dissociation (CID) experiments.MALDI-CID-TOF² analysis is a complex procedure depending on a number of different experimental parameters. Therefore, a step-by-step procedure was used starting with PEG and PPG standards, PEG-PPG blends and endgroup-functionalized PPGs, to understand the fragmentation behaviour of the different species. These results showed that characteristic fragment patterns of the homopolymers and PEG-PPG mixtures can be obtained that facilitate the interpretation of the fragment spectra of PEO-b-PPO di- and triblock copolymers. It was found that di- and triblock copolymers can be differentiated by their fragment spectra. In addition, the sequence of monomer units in the diblock copolymers could be determined.     

Nanoscale localization of poly(vinylidene fluoride) in the lamellae of thin films of symmetric polystyrene-poly(methyl methacrylate) diblock copolymers

We employed thin film blends of diblock copolymers with functional homopolymers as a simple strategy to incorporate organic functional materials into nanodomains of diblock copolymers without serious synthesis. A blend pair of polystyrene-poly(methyl methacrylate) (PS-PMMA) diblock copolymers and poly(vinylidene fluoride) (PVDF) was selected as a model demonstration because PVDF is a well-known ferroelectric polymer and completely miscible with amorphous PMMA. Thin films of symmetric PS-PMMA copolymers provided the nanometer-sized PMMA lamellae, macroscopically parallel to the substrate, in which PVDF chains were dissolved. Thus, amorphous PVDF chains were effectively confined in the PMMA lamellae of thin film blends. The location of PVDF chains in the PMMA lamellae was investigated by the dependence of the lamellar period on the volume fraction of PVDF, from which we found that PVDF chains were localized in the middle of the PMMA lamellae. After the crystallization of PVDF, however, some of PVDF migrated to the surface of the film and formed small crystallites.     

Melt processed blends of poly(styrene-co-acrylonitrile) and poly(phenylene ether) compatibilized with polystyrene-b-polybutadiene-b-poly(methyl methacrylate) triblock terpolymers

Polystyrene-b-polybutadiene-b-poly(methyl methacrylate) triblock terpolymers (SBM) with equal (symmetric) and different (asymmetric) block lengths were used to compatibilize polymer blends based on poly(2,6-dimethyl-1,4-phenylene ether) (PPE) and poly(styrene-co-acrylonitrile) (SAN). First, the rheological behavior of the individual components and their binary mixtures was investigated. Based on the results, samples of PPE, SAN and SBM in weight ratios of 32/48/20 were melt blended and the morphology development during melt processing was investigated. It was found that a raspberry morphology, i.e. dispersion of PPE in SAN with rubbery PB domains at the PPE/SAN interface, could be achieved with a symmetric SBM with under sufficiently high shear rate, while a symmetric SBM with did not yield the desired morphology. Asymmetric SBMs with long PS blocks dissolved in the PPE phase did not display the expected compatibilization effect. In order to obtain a raspberry morphology with asymmetric copolymers it is suggested to pre-blend the SBM with SAN before adding the PPE. Finally it is shown that a commercial PPE containing High Impact Polystyrene (HIPS) as a toughness modifier can be compatibilized with SAN by melt processing using a symmetric SBM triblock terpolymer with      

Effect of chain topology on the self-organization and the mechanical properties of poly(n-butyl acrylate)-b-polystyrene block copolymers

A series of well defined ABA, 3-arm star and bottle brush type copolymers, containing soft poly(n-butyl acrylate) (PBA) blocks and hard blocks of polystyrene (PS) were synthesized by atom transfer radical polymerization (ATRP). Small angle X-ray scattering was used to study the phase separation in these systems and dynamic mechanical analysis and tensile tests were performed to characterize their thermo-mechanical properties. The specific molecular architecture has a major effect on the copolymers self-organization and material properties. The linear ABA type copolymers showed micro phase separation and thermoplastic elastomer (TPE) behavior only at very high PS content. The change of molecular architecture from linear to 3-arm star type resulted in an improved phase separation at lower PS content and better thermoplastic elastomer properties. In contrast the specific brush type molecular architecture seems to prevent the micro phase separation of the PBA and PS components, resulting in amorphous bulk material with single glass transition temperature.     

Miscibility of copolycarbonate blends with poly(styrene-co-acrylonitrile) copolymer and their interaction energies

The phase behavior of dimethyl polycarbonate-tetramethyl polycarbonate (DMPC-TMPC) blends with poly(styrene-co-acrylonitrile) copolymers (SAN) and the interaction energies of binary pairs involved in blend has been explored. DMPC-TMPC copolycarbonates containing 60 wt% TMPC or more were formed miscible blends with SAN containing limited amounts of AN. The miscibility of copolycarbonate with SAN decreases as the DMPC content increases. The miscible blends showed the LCST-type phase behavior or did not phase separate until thermal degradation. The binary interaction energies involved in the miscible blends were calculated from the phase boundaries using the lattice-fluid theory combined with binary interaction model. The phenyl ring substitution with methyl groups did not lead to interactions that are favorable for miscibility with polyacrylonitrile (PAN). The interaction energies of the polycarbonates blends with SAN copolymers as a function of AN content were obtained. It was revealed that the incline of the number of methyl groups on the phenyl rings of bisphenol-A unit acts favorably for the miscibility with SAN copolymer when SAN contains less than about 30 wt% AN and shifts the most favorable interaction to the low AN content.     

Preparation and tribological properties of poly(methyl methacrylate)/styrene/MWNTs copolymer nanocomposites

Poly(methyl methacrylate)/styrene/multi‐walled carbon nanotubes (PMMA/PS/MWNTs) copolymer nanocomposites with different contents have been prepared successfully by means of in situ polymerization method. The structure and the microhardness of PMMA/PS/MWNTs copolymer nanocomposites were characterized. The tribological behaviors of the copolymer nanocomposites were investigated by a friction and wear tester under dry conditions. The relative humidity of the air was about 50% ± 10%. Comparing with pure PMMA/PS copolymer, the copolymer nanocomposites showed not only better wear resistance but also smaller friction coefficient. MWNTs could help the nanocomposites dramatically improve the wear resistance property. The mechanisms of the improvements on the tribological properties of the PMMA/PS/MWNTs copolymer nanocomposites were also discussed in detail. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Nanopatterns of poly(styrene-block-butyl acrylate) block copolymer brushes on the surfaces of exfoliated and intercalated clay layers

We report a study of poly(styrene-block-butyl acrylate) (PSBA) block copolymer brushes on the surfaces of intercalated and exfoliated silicate (clay) layers. The PSBA/clay nanocomposite was synthesized by in situ atom transfer radical polymerization (ATRP) from initiator moieties immobilized within the silicate galleries of the clay particles. Transmission electron microscopy (TEM) analysis showed the existence of both intercalated and exfoliated structures in the nanocomposite. Block copolymer brushes on the surface of exfoliated or intercalated clay layers were found to create nanopatterns after treatment in different solvents. For the block copolymer brushes after treatment in THF, uniform collapsed brush layers are observed. After treatment in acetone, a selective solvent for PBA, wormlike surface aggregates are observed. After treatment in methanol, a precipitant for both of the blocks, micelles as well as wormlike aggregates can be observed. Furthermore, the polymer brushes tend to aggregate together and change their nanopatterns at an elevated temperature.     

Effect of planar extension on the structure and mechanical properties of polystyrene–poly(ethylene-co-butylene)–polystyrene triblock copolymers

Two thermoplastic poly(styrene)–poly(ethylene-co-butylene)–poly(styrene) triblock copolymers containing either spherical or cylindrical poly(styrene) microdomains were pre-oriented through extensional flow. Small angle neutron scattering (SANS) measurements revealed that the pre-oriented triblock with a spherical microstructure adopts a body-centred cubic (bcc) structure with a [111] orientation along the flow direction. For the pre-oriented triblock with a cylindrical microstructure, the cylinder axis is aligned along the extensional flow direction. Investigation of the mechanical properties showed that Young's moduli of the pre-oriented copolymers are highly anisotropic. Specimens were then subject to uniaxial deformation along the extensional flow direction and at the same time microstructural changes induced by the deformation were investigated by SANS. It was found that the deformation of the bcc lattice is affine, and that the deformation of the microstructure is reversible. For the triblock copolymer with a cylindrical microdomain structure the deformation of the lattice was found to be non-affine. In this case, SANS patterns suggest a “micronecking” and a breaking of the cylindrical domains without any change in the domain spacing.