Physicochemical characterization of hydrogels based on polyvinyl alcohol–vinyl acetate blends

Hydrogels made of polyvinyl alcohol–vinyl acetate and its blends with water soluble polymer were studied in terms of swelling behavior, microstructure, and dynamic mechanical properties. Hydrogels prepared by blending polyvinyl alcohol–vinyl acetate with either polyacrylic acid or poly(4‐vinyl pyridine) exhibited a strong pH dependency. When poly(vinyl pyrrolidone) was used for blending, an unusual pH dependency was observed. An increase in the equilibrium water content in all systems resulted in an increase in the freezable water as determined by DSC. Critical point drying led to a striated surface on polyacrylic acid–polyvinyl alcohol–vinyl acetate hydrogels, whereas a porous structure was observed on the freeze‐dried poly(vinyl pyrrolidone)–polyvinyl alcohol–vinyl acetate gels. Hydrogels with elevated storage modulus were obtained when either polyvinyl alcohol–vinyl acetate alone or polyacrylic acid–polyvinyl alcohol–vinyl acetate blends were thermally treated at high temperatures (i.e., 150°C). Low storage modulus was observed for both poly(vinyl pyrrolidone) and poly(4‐vinyl pyridine)‐containing hydrogels. Temperature dependency of storage modulus from 20 to 60°C was observed only for poly(4‐vinyl pyridine)–polyvinyl alcohol–vinyl acetate hydrogels. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 3578–3590, 2001     

Solvent-free generation of poly(vinyl acetals) directly from poly(vinyl acetate)

The simultaneous methanolysis and butryalization of poly(vinyl acetate) was conducted via the reaction of methanol and butyraldehyde with polyvinyl acetate under batch conditions at temperatures from 70°C to 90°C at the vapor pressure of the reactants. It was found that use of an acid catalyst allowed for the methanolysis to be the rate limiting step of a simultaneous methanolysis-butyralization reaction, minimizing the buildup of alcohol repeat units in the polymer during the reaction. As such, use of an excess of aldehyde was counterproductive in that it served to dilute both the methanol and the acetate groups in the polymer phase, lowering the overall rate of the reaction. With 20% stoichiometric excesses of methanol and butyraldehyde, it was possible to produce poly(vinyl butyral) directly from poly(vinyl acetate) with very low residual acetate and overall conversions equivalent to commerical samples. Further, carbon dioxide was evaluated as a reversible plasticizer for polyvinyl acetate during methanolysis. Results at various pressures were consistent with the expectation that the presence of CO₂ would lower the reaction rate, primarily because of dilution of reactants in the CO₂-swollen polymer phase. Finally, it was shown that the simultaneous reaction procedure can be used to generate polyvinyl acetals from a variety of aldehydes.     

Graft polymerization of vinyl acetate onto granular starch: Comparison on the potassium persulfate and ceric ammonium nitrate initiated system

This work was undertaken to discuss in depth the vital differences in the morphological development during synthesis, and properties of starch‐g‐poly‐(vinyl acetate) copolymers using two different initiators, potassium persulfate (KPS) and ceric ammonium nitrate (CAN). KPS‐initiated system gave relatively low values of grafting ratio and grafting efficiency, indicating a great tendency for the formation of poly(vinyl acetate) homopolymer (PVAc). Yet, higher values were seen for the CAN‐initiated system. Transmission electron microscope observations indicated a relatively broad distribution of latex particles for the KPS‐initiated system. The surface potential of latex particles was about ?3.5 mV, which turned out to be insufficient to maintain stability of latex particles. On the other hand, a uniform particle size distribution was found for the CAN‐initiated system, as the surface potential of latex particles was 21.5 mV. Moreover, radicals on starch molecules were generated directly through a redox reaction with positively charged ceric ion. The hydrophobic PVAc chains were thus grafted on starch, resulting in an amphiphilic graft copolymer, which provides a sufficient stabilization degree as a role of surfactant to render a relatively uniform distribution of latex particles. The synthesized starch‐g‐poly(vinyl acetate) copolymers were further converted to starch‐g‐poly(vinyl alcohol) through saponification, which were subjected to evaluations regarding the biodegradation and cell culture capability. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 3017–3027, 2006     

Graft polymerization of vinyl acetate onto starch. Saponification to starch–g–poly(vinyl alcohol)

Graft polymerizations of vinyl acetate onto granular corn starch were initiated by cobalt-60 irradiation of starch-monomer-water mixtures, and ungrafted poly(vinylacetate) was separated from the graft copolymer by benzene extraction. Conversions of monomer to polymer were quantitative at a radiation dose of 1.0 Mrad. However, over half of the polymer was present as ungrafted poly-(vinyl acetate) (grafting efficiency less than 50%), and the graft copolymer contained only 34% grafted synthetic polymer (34% add-on). Lower irradiation doses produced lower conversions of monomer to polymer and gave graft copolymers with lower % add-on. Addition of minor amounts of acrylamide, methyl acrylate, and methacrylic acid as comonomers produced only small increases in % add-on and grafting efficiency. However, grafting efficiency was increased to 70% when a monomer mixture containing about 10% methyl methacrylate was used. Grafting efficiency could be increased to over 90% if the graft polymerization of vinyl acetate-methyl methacrylate was carried out near 0°C, although conversion of monomers to polymer was low and grafted polymer contained 40-50% poly(methyl methacrylate). Selected graft copolymers were treated with methanolic sodium hydroxide to convert starch–g–poly(vinyl acetate) to starch–g–poly(vinyl alcohol). The molecular weight of the poly(vinyl alcohol) moiety was about 30,000. The solubility of starch–g–poly(vinyl alcohol) in hot water was less than 50%; however, solubility could be increased by substituting either acid-modified or hypochlorite-oxidized starch for unmodified starch in the graft polymerization reaction. Vinyl acetate was also graft polymerized onto acid-modified starch which had been dispersed and partially solubilized by heating in water. A total irradiation dose of either 1.0 or 0.5 Mrad gave starch–g–poly(vinyl acetate) with about 35% add-on, and a grafting efficiency of about 40% was obtained. A film cast from a starch–g–poly(vinyl alcohol) copolymer in which homopolymer was not removed exhibited a higher ultimate tensile strength than a comparable physical mixture of starch and poly(vinyl alcohol).     

Synthesis and Characterization of Starch-Poly(vinyl Acetate) Graft Copolymers and their Saponified Form

A redox initiation system based on potassium persulfate/acetone sodium bisulphite (KPS/ASBS) was developed to initiate the graft copolymerization of vinyl acetate (VAc) monomer onto corn starch in aqueous solution. The grafting reaction was studied with respect to grafting yield (GY), grafting efficiency (GE) and total conversion (TC) and results obtained were compared with those a well-established redox initiation system namely potassium persulfate/sodium bisulphite (KPS/SBS). The effect of reaction variables such as redox initiator concentration, liquor ratio, reaction time and temperature as well as VAc concentration were investigated. The GY, GE and TC increased significantly with increase of the redox initiation concentration up to 8/16 mmol/l irrespective of the initiation system used. Moreover, optimal grafting was obtained at 60 ^○C for KPS/ASBS redox system and 70 ^○C for KPS/SBS redox system. Saponification of poly (vinyl acetate)-starch graft copolymers were effected using NaOH in three different bath media (n-hexane, acetone or methanol) to convert starch-g-poly(vinyl acetate) to starch-g-poly(vinyl alcohol). Higher extent of solubility in hot water of the saponified form was achieved by using a bath containing n-hexane/sodium hydroxide; however, increasing the graft yield higher than 26.3% decreases the solubility. The structures and thermal stability of starch, grafted starch copolymer and saponified grafted starch copolymer were characterized by infrared spectroscopy and thermogravimetric analysis. Moreover, the rheological behavior as well as sizing performance of the saponified grafted starch copolymers were evaluated and compared with the native starch and commercial polyvinyl alcohol.     

Synthesis of poly(vinyl alcohol) core-polystyrene shell-type flower microgels

Four types of poly(vinyl alcohol-b-styrene-b-vinyl alcohol) (P(VA-b-S-b-VA)) triblock copolymers were synthesized by hydrolysis of poly(vinyl acetate-b-styrene-b-vinyl acetate) triblock copolymers prepared by radical living polymerization. The polyvinyl alcohol (PVA) core-polystyrene corona-type flower micelles were formed with ASA-4 in benzene at 25°C. The PVA core part of the micelle was crosslinked with hexamethylene diisocyanate in solution. The monodispersed spherical products (microspheres) were synthesized by crosslinking. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 63: 849–854, 1997     

The role of polyvinyl alcohol in emulsion polymerization

Emulsion polymerization of styrene (St) and vinyl acetate (VAc) in the presence of conventional polyvinyl alcohol (PVA), PVA modified with a terminal alkyl group or PVA modified with a terminal thiol group (HS-PVA) was compared. Whereas stable PVAc latexes were obtained, a stable PSt latex was obtained only in the case of HS-PVA. From the adsorption isotherms of these PVAs on the surface of PVAc and PSt latex particles, as well as the grafting efficiencies of VAc and St onto HS-PVA in relation to the stability of the polymerization process, the role of PVA in the emulsion polymerization was discussed.     

Semicontinuous emulsion polymerization of vinyl acetate: Effect of ethoxylation degree of nonionic emulsifiers

Poly(vinyl acetate) latices were prepared in the presence of an ammonium persulfate initiator, 10–50 mol of an ethoxylated nonylphenol nonionic emulsifier, and a poly(vinyl alcohol) colloid stabilizer by applying semicontinuous emulsion polymerization (delayed monomer and initiator addition process) in a laboratory scale similar to industrial practice. Two approaches were applied: the molar concentration of the nonionic emulsifier was kept constant and the weight ratios in the polymerization recipe varied or the weight ratios were kept constant. The effects of the change in the ethoxylation degree of the emulsifier to the final latex viscosity, average polymer molecular weight, polymer grafting degree, surface tension of the latex, and the surface free energy of the dried films were investigated. It was determined that the resultant latex viscosity decreases and the viscosity‐average polymer molecular weight increases with increase of the nonionic emulsifier ethoxylation degree. The increase of the ethoxylation degree does not seriously affect the surface tension of the resultant latex or the surface free energy of the dried poly(vinyl acetate) films. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 844–851, 2002     

PVAc Microspheres via Semicontinuous Emulsion Polymerization: Synthesis,Characterization, Kinetic,and Surface Morphology Studies

Poly (vinyl acetate) (PVAc) latexes are economically important products with many desirable features. They are used as adhesives for porous materials in various processing stages of industries. Synthesis parameters have an important role on the physico-chemical properties of PVAc latexes such as: viscosity, average molecular weight, degree of polymerization, and surface morphology. In this work, PVAc was prepared via semicontinous emulsion polymerization (delayed monomer and initiator addition process) in the presence of ammonium persulfate (APS) as conventional anionic initiator, poly (vinyl alcohol) (PVA) as stabilizer, and sodium lauryl sulfate (SLS) as anionic emulsifier. The surface morphology of PVAc microspheres was, examined using a scanning electron microscope (SEM) and atomic force microscope (AFM). It is evident from the SEM photographs that all the particles became microspheres and are uniform in shape. The use of AFM for imaging of polyvinyl acetate confirms a typical sphere polymer. The effect of changes in the different parameters such as concentration of emulsifier, initiator concentration, and presence or absence of buffer on the vinyl acetate (VAc) conversion, the steady state polymerization rate, the viscosity-average molecular weight, and the final latex viscosity of synthesized PVAc were investigated. The effects of anionic emulsifier on the synthesized PVAc are also compared with those obtained by the nonionic emulsifier. The comparison indicated that the VAc monomer conversion and the final latex viscosity of the anionic system were higher than for the nonionic system but the viscosity-average polymer molecular weight of the anionic system was lower than that of the nonionic system. The adhesive strength of the synthesized PVAc latex was examined and the load and deflection data were reported.     

醋酸甲酯羰基化合成醋酸乙烯研究进展

以醋酸甲酯为原料,经羰基化合成亚乙基二乙酸酯中间产物、再裂解生成醋酸乙烯的技术方法是一种新型煤化工合成醋酸乙烯工艺路线。综述了国内外醋酸甲酯制备醋酸乙烯工艺过程以及催化剂体系,使用廉价醋酸甲酯为原料开发高附加值的下游产品,充分挖掘醋酸甲酯的经济效益,减少对苯二甲酸和聚乙烯醇生产成本,符合我国石油化工生产现状,具有良好的经济效益和社会价值。     

Preparation of poly(vinyl amine)‐grafted crosslinked poly(vinyl alcohol) microspheres

Crosslinked poly(vinyl alcohol) (CPVA) microspheres were first prepared via the suspension polymerization of vinyl acetate and the alcoholysis of poly(vinyl acetate). Afterwards, a two‐step method involving graft polymerization and Hofmann degradation was used to prepare functional poly(vinyl amine)‐grafted crosslinked poly(vinyl alcohol) (PVAm–CPVA) microspheres, onto which poly(vinyl amine) (PVAm) macromolecules were grafted. The graft polymerization of acrylamide (AM) on CPVA microspheres was performed with cerium salt as the initiator in an acidic aqueous medium, resulting in polyacrylamide (PAM)‐grafted CPVA microspheres. Subsequently, the grafted PAM was transformed into PVAm via the Hofmann degradation reaction, and PVAm–CPVA microspheres were prepared. The effects of the main factors on the graft polymerization and Hofmann degradation were examined, and the reaction mechanisms were researched in depth. The experimental results showed that for the graft polymerization of AM on CPVA microspheres initiated by cerium salt, the acid concentration and the amount of cerium salt affected the grafting degree of PAM greatly. For the Hofmann degradation reaction of the grafted PAM, the amination degree of PVAm–CPVA microspheres was obviously affected by the amount of sodium hypochlorite in the presence of sodium hydroxide. The preliminary adsorption tests showed that PVAm–CPVA microspheres were multifunctional and had strong adsorption ability for Fe(III) ions by chelation action and for chromate ions (CrO) by strong electrostatic interactions. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Experimental investigation of vinyl chloride drop behavior during suspension polymerization

The effects of some polymerization conditions on poly(vinyl chloride) (PVC) particles produced by the suspension polymerization process were studied on a laboratory scale. The different stages of vinyl chloride suspension polymerization were investigated experimentally by using an on-line sample withdrawal technique during reaction. It was found that the method of addition of initiator has a great effect on the PVC particle uniformity as well as the size distribution. Furthermore, when the initiator was predispersed in the continuous phase, some latex particles were formed. The effect of the type of stabilizer was also studied with two different types of PVA [partially hydrolyzed poly(vinyl acetate)]. It was found that by changing the stabilizer, the particle size, the porosity, and the morphology could change. When H80 (PVA with a degree of hydrolysis of 80% and a molecular weight of 259,000) stabilizer was used, the rigidity of the PVC particles was weak. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 65: 127–134, 1997     

两亲性聚乙烯醇-b-聚苯乙烯嵌段共聚物的合成及表征

采用原子转移自由基聚合(ATRP)法合成了具有两亲性的聚乙烯醇-b-聚苯乙烯嵌段共聚物P(VA-b-St)。首先利用调聚反应制备了带三氯甲基端基的聚醋酸乙烯大分子引发剂。以联二吡啶作配体、氯化亚铜为催化剂,引发苯乙烯单体聚合,得到结构明确的P(VAc-b-St)嵌段共聚物,而后通过皂化反应将其水解,从而得到两亲性嵌段共聚物P(VA-b- St);产物采用FT-IR、1H NMR、GPC等方法进行结构表征。P(VA-b-St)在不同浓度溶剂中的自组装行为用TEM进行了观察,结果表明:P(VA-b-St)可在DMF溶剂中形成球状囊泡结构,其尺寸达到纳米级。     

Preparation and characterization of dual responsive sodium alginate‐g‐poly(vinyl alcohol) hydrogel

Poly(vinyl alcohol) (PVA) was chosen as a controllable gelator to prepare sodium alginate (SA)‐based physically cross‐linked dual‐responsive hydrogel by three steps. First, polyvinyl acetate (PVAc) was grafted onto SA via radical copolymerization. Then, the copolymer was subsequently converted into SA‐g‐poly(vinyl alcohol) (SAPVA) by alcoholysis reaction. PVA content of SAPVA was tailored by controlling the graft percentage of PVAc, i.e. through varying the amount of vinyl acetate during copolymerization. Finally, SAPVA hydrogels were formed by freezing‐thawing cycles. The structure of the graft copolymers was verified with FTIR spectroscopy. X‐ray diffraction analysis results revealed that the crystallinity of SAPVA hydrogels depended on the PVA content of SAPVA. The swelling test showed that SAPVA hydrogels were pH‐responsive, and the swelling was reversible. SAPVA hydrogels also behaved electric‐responsive. In addition, the pH‐sensitivity of SAPVA hydrogels was able to be controlled with the composition of the hydrogels. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Radiation grafting of poly(ethylene terephthalate) (PET) fibre,II. Hydrolysis of grafted poly(vinyl acetate) to poly(vinyl alcohol)

Poly(ethylene terephthalate) fibres grafted with poly(vinyl acetate) by γ-radiation were hydrolysed under alkaline and acidic conditions in order to obtain poly(ethylene terephthalate)-graft-poly(vinyl alcohol) fibres. In alkaline media poly(ethylene terephthalate) degraded without appreciable conversion of acetate to hydroxyl groups. During acid hydrolysis no change in tensile properties of the fibres was observed up to an extent of 50% conversion of acetate to hydroxyl groups. Further change in the tensile strength and the elongation at break was attributed partly to the grafted poly(vinyl acetate)/poly(vinyl alcohol) balance and partly to the loss due to degradation of the fibres.     

Synthesis and characterization of polyvinyl acetate/montmorillonite nanocomposite by in situ emulsion polymerization technique

Exfoliated polyvinyl acetate/montmorillonite nanocomposite (PVAc/MMT) was prepared via in situ emulsion polymerization. The resulting PVAc with various organophilic MMT contents was investigated. In the nanocomposite latex preparation, sodium lauryl sulfate (SLS), ammonium persulfate (APS), and poly (vinyl alcohol) (PVA) are used as anionic emulsifier, conventional anionic initiator, and stabilizer, respectively. The samples were characterized using elemental analysis, X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), atomic force microscopy (AFM). The XRD and AFM results demonstrate that the MMT well dispersed at molecular level in the PVAc matrix. Thermal properties of the nanocomposite were studied by using differential scanning calorimetric analysis (DSC). The exfoliated PVAc/MMT nanocomposite showed a higher glass transition temperature and a better thermal stability compared to the pure PVAc.     

Solid state NMR and LVSEM studies on the hardening of latex modified tile mortar systems

Construction mortars contain a broad variety of both inorganic and organic additives beside the cement powder. Here we present a study of tile mortar systems based on portland cement, quartz, methyl cellulose and different latex additives. As known, the methyl cellulose stabilizes the freshly prepared cement paste, the latex additive enhances final hydrophobicity, flexibility and adhesion. Measurements were performed by solid state nuclear magnetic resonance (NMR) and low voltage scanning electron microscopy (LVSEM) to probe the influence of the latex additives on the hydration, hardening and the final tile mortar properties. While solid state NMR enables monitoring of the bulk composition, scanning electron microscopy affords visualization of particles and textures with respect to their shape and the distribution of the different phases.

Within the alkaline cement paste, the poly(vinyl acetate) (VAc)-based latex dispersions stabilized by poly(vinyl alcohol) (PVA) were found to be relatively stable against hydrolysis. The influence of the combined organic additives methyl cellulose, poly(vinyl alcohol) and latexes stabilized by poly(vinyl alcohol) on the final silicate structure of the cement hydration products is small. But even small amounts of additives result in an increased ratio of ettringite to monosulfate within the final hydrated tile mortar as monitored by ²⁷Al NMR. The latex was found to be adsorbed to the inorganic surfaces, acting as glue to the inorganic components. For similar latex water interfaces built up by poly(vinyl alcohol), a variation in the latex polymer composition results in modified organic textures. In addition to the networks of the inorganic cement and of the latex, there is a weak network build up by thin polymer fibers, most probably originating from poly(vinyl alcohol). Besides the weak network, polymer fibers form well-ordered textures covering inorganic crystals such as portlandite.     

Ultrasonic attenuation and mobility in polymer solutions and dispersions. Poly(vinyl alcohol) and poly(vinyl acetate)

Summary To obtain informations about molecular processes, poly(vinyl alcohol) solutions and poly(vinyl acetate) solutions and dispersions have been studied by ultrasonic methods in the frequency range from 200 kHz to 150 MHz. The measured excess attenuations are qualitatively discussed in terms of cooperative and local mode motions of the macromolecules. In poly(vinyl alcohol) solutions with different residual vinyl acetate content a mixing of normal and local mode motions has been observed. In poly(vinyl acetate)/toluene solution two discrete relaxation processes have been detected which are probably related to a local mode and a coupling of local and normal mode motions, respectively. The frequency-temperature dependence of the absorption maximum of the poly(vinyl acetate) dispersion follows the WLF relation.     

高固含量醋酸乙烯-乙烯共聚乳液的研制

介绍了一种固含量在60％左右的醋酸乙烯-乙烯(VAE)共聚乳液的制备方法。讨论了乳化剂、聚乙烯醇、醋酸乙烯、乙烯、引发剂等对乳液合成及其性能的影响，并确定了合适的生产工艺，该工艺生产的产品固含量高、黏度低、柔韧性好，初粘性、快干性和耐水性均较常规产品有显著提高。     

Characterization of grafting in the emulsion polymerization of vinyl acetate using poly(vinyl alcohol) as stabilizer

Emulsion polymerizations of vinyl acetate (VAc) with polyvinyl alcohol (PVA) as emulsifier were carried out by both batch and semicontinuous processes. The extent of grafting of vinyl acetate onto the PVA chains was investigated by a new method for separating the various polymer fractions in high solids content latexes. The quantification was carried out by a three‐step separation and selective solubilization of the PVAc latexes. After the separation, the water‐soluble PVA and the solvent‐soluble PVAc components were characterized by gel permeation chromatography and ¹³C–NMR, from which the accuracy of this method was verified. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 1739–1747, 2001