新型掺铈钇铁石榴石磁光薄膜材料

对新型掺铈钇铁石榴石磁光薄膜材料(Ce:YIG)的制备工艺、磁光特性及理论分析进行了较全面的评述,并指出今后研究的方向。     

Sol-gel法制备(BiAl)DyIG石榴石磁光记录薄膜

采用柠檬酸络合物型溶胶 凝胶法首次制备得到了具有垂直各向异性的(BiAl)DyIG石榴石磁光记录薄膜,并对材料结构和磁光性质进行了研究,结果得到石榴石磁光记录薄膜磁滞回线具有较好的矩形比,在430nm和520nm的品质因子为2°和1.5°,最佳晶化温度为675℃。     

Ce掺杂对TbFeCo材料磁光性能影响的研究

采用射频磁控溅射方法制备了TbFeCo非晶磁光薄膜，并在TbFeCo中引入轻稀土元素Ce，测试了薄膜的磁光性能。研究了薄膜成分对其磁光性能的影响。结果表明；在TbFeCo薄膜中掺入少量Ce时，薄膜的磁光克尔角及矫顽力都有所提高，矩形度也增加了。但随Ce掺入量的增加，薄膜的磁光性能发生恶化，较好的掺杂在10.31?左右。     

RF溅射淀积Ce∶YIG磁光薄膜的热处理结晶化研究

基片温度低于溅射外延条件 ,采用低溅射功率密度磁控溅射沉积 ,进行后期热处理结晶化 ,制备出膜厚为 30 0 nm的掺铈钇铁石榴石 Ce∶ YIG磁光薄膜。对热处理前后的磁光特性进行比较 ,并分析了热处理结晶化过程中附属相的变化。薄膜在空气中热处理结晶化温度在 650℃附近。热处理后 ,室温下 633nm处其法拉第旋转系数约为 1.9× 10 4 deg/ cm,光吸收系数为 2 50 0 cm-1。     

YIG薄膜制备方法研究

就工艺，测试结果，性能等方面综述了钇铁石榴石YIG（Yttrium Iron Garnet)薄膜的制备方法，包括Sol-Gel、CVD、溅射、PLD、LPE等。从YIG复合薄膜的制备、基片选择等角度，提出通过提高YIG薄膜制品的磁光性能从而改善磁光器件整体性能的新思路。     

离子注入法增强YIG单晶薄膜的磁光效应

利用离子注入技术，将Ce^ 3离子注入到YIG单晶薄膜中，剂量为10^14-10^16ion/cm^2，能量为500keV。对注入前后的样品进行光吸收谱测量，发现注入后的样品光吸收有明显的增加，且样品颜色变深，对样品进行高温退火，可有效地降低光损耗，离子注入样品磁光特性测量表明Ce^ 3薄膜有很大的磁光增强作用，且法拉第旋转角随注入剂量增加而增大。     

掺铋钇铁石榴石磁光陶瓷的热压烧结及其性能研究

钇铁石榴石(Y₃Fe₅O₁₂, YIG)材料因其优异的磁性能和磁光性能在微波通信、激光技术和光纤通讯等领域具有重要应用。离子掺杂是提高YIG材料磁光性能的有效途径之一, 本研究选择离子半径适配的Bi³⁺掺杂改性YIG陶瓷以提高材料的磁光性能。本工作采用固相法热压烧结制备Bi_xY_3-xFe₅O₁₂ (x=0、0.3、0.6、0.9)陶瓷, 并研究Bi³⁺掺杂对YIG陶瓷材料相结构、微观形貌、红外透过性、磁性能以及磁光性能的影响。结果表明: 陶瓷样品均呈石榴石立方相结构; 显微结构致密, Bi³⁺掺杂后晶粒尺寸不同程度增大; 样品红外透过率良好, 随Bi³⁺掺杂量增大而降低; 陶瓷样品的法拉第旋转角随Bi³⁺掺杂量增加呈线性变化, Bi³⁺掺杂量每增加1% (原子分数), 在波长1064 nm和1550 nm处变化量分别约为-49.0 (°)/cm和-30.2 (°)/cm。Bi_0.6Y_2.4Fe₅O₁₂陶瓷样品在1064 nm和1550 nm波长下法拉第旋转角分别达到-703.3 (°)/cm和-461.5 (°)/cm, 绝对值远高于未掺杂YIG陶瓷的277.6 (°)/cm和172.0 (°)/cm。由此可见, 掺杂适量Bi³⁺可以显著增强YIG陶瓷材料的磁光性能。     

热处理对Tb0.27Dy0.73Fe2巨磁致伸缩薄膜性能的影响

本文研究了热处理对Tb0.27Dy 0.73Fe2薄膜磁性及巨磁致伸缩性能的影响.XRD分析表明制备态的Tb0.27Dy 0.73Fe2薄膜为非晶态,并且在450℃退火仍然保持非晶态,制备态的Tb0.27 Dy0.73Fe2薄膜显示垂直磁各向异性,在退火后向平行磁各向异性变化.热处理提高了Tb0.27Dy0.73Fe2薄膜在低磁场下的磁致伸缩特性.     

离子掺杂钇铁石榴石磁光材料研究进展

综述了钇铁石榴石型磁光材料的研究进展,以及通过离子掺杂提高单晶和薄膜材料的比法拉第旋转角、改善材料温度稳定性以及近年来受到重视并有望在磁光器件中得到广泛应用的低成本钇铁石榴石纳米晶/有机分散介质复合薄膜材料的研究进展与存在的问题,概述了目前实际使用中的磁光法拉第转子材料的应用情况,并展望了高性能磁光材料的发展。     

热处理对Tb0.27Dy0.73Fe2巨磁致伸缩薄膜性能的影响

本文研究了热处理对Tb0.27Dy0.73Fe2薄膜磁性及巨磁致伸缩性能的影响。XRD分析表明制备态的Tb0.27Dy0.73Fe薄膜为非晶态,并且在450℃退火仍然保持非晶态,制备态的Tb0.27Dy0.73Fe2薄膜显示垂直磁各向异性,在退火后向平行磁各向异性变化。热处理提高了Tb0.27Dy0.73Fe2薄膜在低磁场下的磁致伸缩特性。     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Thixotropy of Systems with Shear Thinning and Plastic Flow Behavior

The definition of the thixotropy is a decrease in viscosity with time in shear and a subsequent recovery of viscosity after the shear deformation is removed.We ...     

Effect of Oxide Assisted Metal Nanoparticles on Microstructure and Morphology of Gallium oxide Nanowires

Several researches have been reported about the characteristic of β-Ga2O3 nanowires which was synthesized on nickel oxide particle. But indeed, recent researches about synthesis of β-Ga2O3 nanowires on oxide-assisted transition metal are limited to nickel or cobalt oxide catalyst. In this work, Gallium oxide (β-Ga2O3 ) nanowires were synthesized by a simple thermal evaporation method from gallium powder in the range of 700 - 1000℃ using the iron, nickel, copper, cobalt and zinc oxide as a catalyst, respectively. The β-Ga2O3 nanowires with single crystalline without defects were successfully synthesized at the reaction temperature of 850, 900 and 950℃ in all the catalysts. But optimum experimental condition in synthesis of nanowires varied with the kind of catalyst. As increasing synthesis temperature,the morphology of gallium oxide nanowires changed from nanowires to nanorods, and its diameter increased. From these results, we could be proposed that the growth mechanism of β-Ga2O3 nanowires was changed with synthesis temperature of nanowires. Microstructure and morphology of Synthesized nanowire was characterized by HR-TEM, FE-SEM, EDX and XRD.     

Brainstorming for ISO Strategy 2016-2020

正Responding to ISO’s appeal for survey for the to-be-developed ISO Strategy Plan for 2016-2020,SAC hosted a special workshop over the needs and comments of various fi elds on June 8 in Beijing.The workshop was attended by ISO President-elect and Ansteel General Manager Zhang Xiaogang,SAC Vice-Administrator Yu Xinli,and 30 experts from