GaN光电阴极测试与评估技术研究

GaN光电阴极的制备成功与否需用科学手段加以评估.在GaAs光电阴极多信息量测试系统的基础上,增设紫外光源,并对评估软件重新加以编写,设计出GaN光电阴极测试评估系统.利用该系统测试了GaN光电阴极在制备过程中的Cs源电流、O源电流、光电流和激活室真空度等多个信息量,并利用激活后的光谱响应对阴极进行了评估,实现了对GaN光电阴极性能的客观评价.     

梯度掺杂结构GaN光电阴极的激活工艺研究

利用自行研制的光电阴极多信息量测试评估系统,在线测试了梯度掺杂结构GaN光电阴极在激活过程中的光电流、Cs源电流和O源电流。根据激活后的阴极光谱响应曲线和量子产额曲线,分析了超高真空室真空度、激活前的阴极表面净化程度、激活中首次进Cs量、激活中的Cs/O比以及Cs/O源在激活中的供给方式等对阴极激活的影响,提出了梯度掺...     

光谱响应在线测试仪的研制与应用

基于光电阴极光谱响应测试原理,研制了光谱响应在线测试仪,经多次实验验证,准确度达到1 nA,完全能够检测出NEA激活过程中产生的微弱光电信号,且具有良好的重复性.利用该光谱响应测试仪,成功实现了激活台内负电子亲和势(NEA)光电阴极激活过程中的光谱响应在线测试,获得了光谱响应曲线,并将其转换成阴极的量子产额曲线.通过曲线拟合方法计算出反映阴极性能的重要参数,得到了大量的阴极信息,弥补了依靠光电流监控阴极信息的不足.     

高真空系统气体成分对GaAs光电阴极稳定性的影响

GaAs 光电阴极以其量子效率高、光谱可调等优点广泛应用于微光夜视领域,尤其以高积分灵敏度的特性区别于多碱光电阴极,而 GaAs 光电阴极负电子亲合势的特性是通过 Cs,O 激活实现的,但是激活结束后,负电子亲合势的维持受诸多因素影响,如激活源、激活方式、气体氛围等。为了探究超高真空系统中影响 GaAs 光电阴极稳定性的因素,开展了 GaAs 光电阴极的激活实验和稳定性实验,对激活光电流曲线与腔室气体成分进行了监测,实验结果表明,在真空度优于 1×10^-6 Pa 的高真空系统中,影响其稳定性的是腔室中的气体成分,其中对稳定性影响最大的是 H₂O,真空系统中 H₂O分压的增加会导致 GaAs 光电阴极的 Cs,O 激活层迅速破坏,光电发射能力急剧下降。     

GaN与GaAs NEA光电阴极稳定性的比较

利用自行研制的光电阴极激活评估实验系统,对激活后的反射式GaN及GaAs光电阴极进行了稳定性测试,获得了Cs/O激活一段时间后阴极随时间变化的光谱响应,通过计算得到量子效率曲线.结果表明:激活结束后GaN灵敏度可以在较长时间内保持稳定,而后缓慢衰减.而GaAs光电阴极的光电流随时间近似呈指数衰减.结合阴极表面双偶极层结构以及表面化学成分,分析原因主要是:两种阴极表面进行Cs/O激活后形成的双偶极子的结构不同、衰减过程中双偶极层化学成分变化方式不同决定.GaN光电阴极激活后cs以复杂氧化物存在,更加稳定,灵敏度的衰减主要是由未分解的氧引起,而GaAs灵敏度下降的原因主要是表面双偶极层中的Cs极易脱附,影响其稳定性.     

NEA GaN和GaAs光电阴极的比较

针对GaN基光电阴极激活过程中Cs-O交替存在的光电流的增幅问题,本文主要比较了GaN和GaAs材料性质、表面结构以及激活过程中光电阴极的光电流.发现GaN的熔点高于GaAs,在制备GaN基光电阴极时则需要更高的热清洗温度;如果用双偶极子模型描述GaN(1000)和GaAs(100)表面的光电发射机理,GaN(1000)表面Cs原子与O原子形成第二偶极矩O-Cs,几乎\     

不同结构的反射式GaAs光电阴极的光谱特性比较

利用分子束外延生长了三种结构的反射式GaAs光电阴极,其中一种为传统结构的反射式GaAs光电阴极,另外两种为具有GaAlAs缓冲层的均匀掺杂和梯度掺杂反射式GaAs光电阴极.激活后的光谱响应测试结果表明,与传统结构的反射式GaAs光电阴极相比,具有GaAlAs缓冲层的均匀掺杂反射式GaAs光电阴极的长波响应更好,而具有...     

梯度掺杂GaN光电阴极的光谱响应测试与分析

用光谱响应测试仪得到了反射式梯度掺杂GaN光电阴极在激活和衰减过程中的光谱响应曲线,发现此曲线不断发生变化。在激活过程中光谱响应不断提高,且长波响应提高较快;衰减过程中光谱响应不断下降,长波响应下降得更快。结果表明：光谱响应曲线的变化与光电阴极高能光电子的逸出有关。GaN光电阴极发射的电子能量分布随入射光子能量升高而向高能端偏移,阴极表面势垒形状的变化对低能光激发电子的影响更大,导致光谱响应曲线随入射光波长改变而产生了不同的变化。     

高积分光电灵敏度多层Be浓度掺杂的GaAs负电子亲和势光电阴极

研究了变掺杂浓度结构对GaAs负电子亲和势光电阴极积分光电灵敏度的影响.通过MBE生长了两组GaAs同质外延样品.其中一组采用了均匀掺杂的单层结构,Be掺杂浓度为1×1019cm-3;另一组采用了变掺杂的多层结构,从衬底开始Be的掺杂浓度依次为1×1019,7×1018,4×1018和1×1018cm-3.负电子亲和势光电阴极通过在高真空系统中交替通入Cs和O激活得到.在线光谱响应测试曲线表明,多层Be掺杂结构光阴极的积分光电灵敏度比单层Be掺杂结构光阴极的积分光电灵敏度至少提高了50%.两种结构的GaAs样品表现出不同的表面应力情况.     

发射层对指数掺杂Ga1-χAlχ As/GaAs光阴极性能的影响

为了探索发射层厚度对指数掺杂Ga1-χAlχAs/GaAs光电阴极光学性能与光电发射性能的影响,实验制备了两种发射层厚度不同的阴极样品,并测试得到400μm～1 000 nm内反射率、透射率与光谱响应曲线.实验结果说明发射层2.0 μm厚的样品比1.6μm厚的样品性能更好.利用薄膜光学矩阵理论公式计算阴极膜系反射率、透射率、吸收率与发射层厚度的关系公式,并对原有的量子效率公式进行光谱反射率和短波截止限的修正.用修正后的公式仿真不同发射层厚度下光阴极吸收率与光谱响应曲线,指出发射层厚度对阴极光学性能与光电发射性能的不同影响.进一步计算得到指数掺杂的Ga1-χAlχAs/GaAs光电阴极最佳发射层厚度范围是1.8μm～2.4μm.     

Resolution Enhancement Technology:Integrated Process Solutions using OPC

DUV lithography, using the 248 nm wavelength, is a viable manufacturing option for devices with features at 130 nm and less. Given the low kl value of the lithography, integrated process development is a necessary method for achieving acceptable process latitude. The application of assist features for rule based OPC requires the simultaneous optimization of the mask, illumination optics and the resist.Described in this paper are the details involved in optimizing each of these aspects for line and space imaging.A reference pitch is first chosen to determine how the optics will be set. The ideal sigma setting is determined by a simple geometrically derived expression. The inner and outer machine settings are determined, in turn,with the simulation of a figure of merit. The maximum value of the response surface of this FOM occurs at the optimal sigma settings. Experimental confirmation of this is shown in the paper.Assist features are used to modify the aerial image of the more isolated images on the mask. The effect that the diffraction of the scattering bars (SBs) has on the image intensity distribution is explained. Rules for determining the size and placement of SBs are also given.Resist is optimized for use with off-axis illumination and assist features. A general explanation of the material' s effect is discussed along with the affect on the through-pitch bias. The paper culminates with the showing of the lithographic results from the fully optimized system.     

Cost-effective test solutions for smart card and other integrated flash applications

From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.     

Theoretical analysis of the relationship between the Brillouin gain coefficient and the strain in the optical-fiber sensors

The relation between the power of the Brillouin signal and the strain is one of the bases of the distributed fiber sensors of temperature and strain. The coefficient of the Bfillouin gain can be changed by the temperature and the strain that will affect the power of the Brillouin scattering. The relation between the change of the Brillouin gain coefficient and the strain is thought to be linear by many researchers. However, it is not always linear based on the theoretical analysis and numerical simulation. Therefore, errors will be caused if the relation between the change of the Brillouin gain coefficient and the strain is regarded as to be linear approximately for measuring the temperature and the strain. For this reason, the influence of the parameters on the Brillouin gain coefficient is proposed through theoretical analysis and numerical simulation.     

An improved parallel thinning algorithm with two subiterations

The parallel thinning algorithm with two subiterations is improved in this paper. By analyzing the notions of connected components and passes, a conclusion is drawn that the number of passes and the number of eight-connected components are equal. Then the expression of the number of eight-connected components is obtained which replaces the old one in the algorithm. And a reserving condition is proposed by experiments, which alleviates the excess deletion where a diagonal line and a beeline intersect. The experimental results demonstrate that the thinned curve is almost located in the middle of the original curve connectivelv with single pixel width and the processing speed is high.     

Novel fiber-optical interferometer with miniaturized probe for in-hole measurements

Today, micro-system technology and the development of new MEMS （Micro-Electro-Mechanical Systems） are emerging rapidly. In order for this development to become a success in the long run, measurement systems have to ensure product quality. Most often, MEMS have to be tested by means of functionality or destructive tests. One reason for this is that there are no suitable systems or sensing probes available which can be used for the measurement of quasi inaccessible features like small holes or cavities. We present a measurement system that could be used for these kinds of measurements. The system combines a fiber optical, miniaturized sensing probe with low-coherence interferometry, so that absolute distance measurements with nanometer accuracy are possible.     

Study of waveguide coupling efficiency in hybrid silicon lasers

This paper presents a new method to increase the waveguide coupling efficiency in hybrid silicon lasers. We find that the propagation constant of the InGaAsP emitting layer can be equal to that of the Si resonant layer through improving the design size of the InP waveguide. The coupling power achieves 42% of the total power in the hybrid lasers when the thickness of the bonding layer is 100 nm. Our result is very close to 50% of the total power reported by Intel when the thickness of the thin bonding layer is less than 5 nm. Therefore, our invariable coupling power technique is simpler than Intel＇s.     

Teleportation of an arbitrary unknown N-qubit entangled state under the controlling of M controllers

A new quantum protocol to teleport an arbitrary unknown N-qubit entangled state from a sender to a fixed receiver under M controllers(M < N) is proposed. The quantum resources required are M non-maximally entangled Greenberger-Home-Zeilinger (GHZ) state and N-M non-maximally entangled Einstein-Podolsky-Rosen (EPR) pairs. The sender performs N generalized Bell-state measurements on the 2N particles. Controllers take M single-particle measurement along x-axis, and the receiver needs to introduce one auxiliary two-level particle to extract quantum information probabilistically with the fidelity unit if controllers cooperate with it.     

Diode-end-pumped Nd:YVO4/LBO lasers with 4.2W continuous-wave output at 457 nm

A continuous-wave (CW) 457 nm blue laser operating at the power of 4.2 W is demonstrated by using a fiber coupled laser diode module pumped Nd: YVO4 and using LBO as the intra-cavity SHG crystal With the optimization of laser cavity and crystal parameters, the laser operates at a very high efficiency. When the pumping power is about 31 W, the output at 457nm reaches 4.2 W, and the optical to optical conversion efficiency is about 13.5% accordingly. The stability of the out putpower is better than 1.2% for 8 h continuously working.     

Call for Papers

正Wireless Body-area Networks The last decade has witnessed the convergence of three giant worlds:electronics,computer science and telecommunications.The next decade should follow this convergence in most of our activities with the generalization of sensor networks.In particular with the progress in medicine,people live longer and the aging of population will push the development of wireless personal networks     

Call for Papers—Feature Topic,Vol.12,No.7,2015

正Information Centric Networking Information-Centric Networking(ICN) is an emerging direction in Future Internet architecture research,gaining significant tractions among academia and industry.Aiming to replace the conventional host-to-host communication model by a data-centric model,ICN treats data content as the first