掺杂GaAs/Al0.3Ga0.7As超晶格的光致发光特性分析

在室温下,通过光致发光实验研究了用MBE生长的GaAs/Al0.3Ga0.7As超晶格材料的光致发光特性,对测得的发光峰进行了指认.理论计算和实验结果符合很好.     

Hydrogen plasma passivation of bulk GaAs and Al0.3Ga0.7As/GaAs multiple-quantum-well structures on Si substrates

Hydrogen (H) plasma passivation effects on GaAs grown on Si substrates (GaAs on Si) are investigated in detail. H plasma exposure effectively passivates both the shallow and deep defects in GaAs on Si, which improves both the electrical and optical properties. It was found that the minority carrier lifetime is increased and the deep level concentration is decreased by the H plasma exposure. In addition, after H plasma exposure, room temperature photoluminescence (PL) for Al_0.3Ga_0.7As/GaAs multiple-quantum-well (MQW) on Si is enhanced with a decrease in the spectral width.     

Investigation of DX centers in modulation-doped field-effect transistor-type Al0.3Ga0.7As/GaAs heterostructures using a fourier-transform deep level transient spectroscopy system

Al_0.3Ga_0.7As:Si/GaAs modulation-doped field-effect transistor-type heterostructures were grown using two different growth temperatures (500 and 620°C) and three doping modes (δ-doping, pulse-doping, and uniform-doping). Deep level transient spectroscopy (DLTS) measurements were performed on these structures using a new Fourier-analysis method. Up to four DLTS peaks, related to the different possible configurations of the nearest Al and Ga neighbors around each DX site, were observed. Both the growth temperature and the doping-mode are found to affect the DLTS spectra, in particular the number of observed peaks and their width. These results are interpreted in terms of the different mobilities of the Si doping atoms on the surface during growth.     

High uniformity of Al0.3Ga0.7As/ln0.15Ga0.85As doped-channel structures grown by molecular beam epitaxy on 3″ GaAs substrates

Al_0.3Ga_0.7As/ln_0.15Ga_0.85As doped-channel structures were grown by molecular beam epitaxy on 3″ GaAs substrates. The uniformities of electrical and optical properties across a 3″ wafer were evaluated. A maximum 10% variation of sheet charge density and Hall mobility was achieved for this doped-channel structure. A1 μm long gate field-effect transistor (FET) built on this layer demonstrated a peak transconductance of 350 mS/mm with a current density of 470 mA/mm. Compared to the high electron mobility transistors, this doped-channel FET provides a higher current density and higher breakdown voltage, which is very suitable for high-power microwave device applications.     

Photoluminescence studies of In0.7Al0.3As/In0.75Ga0.25As/In0.7Al0.3As metamorphic heterostructures on GaAs substrates

The influence of the design of the metamorphic buffer of In_0.7Al_0.3As/In_0.75Ga_0.25As metamorphic nanoheterostructures for high-electron-mobility transistors (HEMTs) on their electrical parameters and photoluminescence properties is studied experimentally. The heterostructures are grown by molecular-beam epitaxy on GaAs (100) substrates with linear or step-graded In _x Al_{1 ? x} As metamorphic buffers. For the samples with a linear metamorphic buffer, strain-compensated superlattices or inverse steps are incorporated into the buffer. At photon energies ?ω in the range 0.6–0.8 eV, the photoluminescence spectra of all of the samples are identical and correspond to transitions from the first and second electron subbands to the heavy-hole band in the In_0.75Ga_0.25As/In_0.7Al_0.3As quantum well. It is found that the full width at half-maximum of the corresponding peak is proportional to the two-dimensional electron concentration and the luminescence intensity increases with increasing Hall mobility in the heterostructures. At photon energies ?ω in the range 0.8–1.3 eV corresponding to the recombination of charge carriers in the InAlAs barrier region, some features are observed in the photoluminescence spectra. These features are due to the difference between the indium profiles in the smoothing and lower barrier layers of the samples. In turn, the difference arises from the different designs of the metamorphic buffer.     

新型复合沟道Al0.3Ga0.7N/Al0.05Ga0.95N/GaN HEMT低相位噪声微波单片集成压控振荡器

设计并研制了一种新型复合沟道Al0.3Ga0.7N/Al0.05Ga0.95N/GaN HEMT(CC-HEMT)微波单片集成压控振荡器(VCO),且测试了电路的性能.CC-HEMT的栅长为1μm,栅宽为100μm.叉指金属-半导体-金属(MSM)变容二极管被设计用于调谐VCO频率.为提高螺旋电感的Q值,聚酰亚胺介质被插入在电感金属层与外延在蓝宝石上GaN层之间.当CC-HEMT的直流偏置为Vgs=-3V,Vds=6V,变容二极管的调谐电压从5.5V到8.5V时,VCO的频率变化从7.04GHz到7.29GHz,平均输出功率为10dBm,平均功率附加效率为10.4%.当加在变容二极管上电压为6.7V时,测得的相位噪声为-86.25dBc/Hz(在频偏100KHz时)和-108dB/Hz(在频偏1MHz时),这个结果也是整个调谐范围的平均值.据我们所知,这个相位噪声测试结果是文献报道中基于GaN HEMT单片VCO的最好结果.     

GaAs/Al0.3Ga0.7As 量子阱红外探测器光谱特性研究

采用金属有机物化学气相沉积法(MOCVD)生长GaAs/Al0.3Ga0.7As量子阱材料,制备300 m300 m台面,内电极压焊点面积为20 m20 m,外电极压焊点面积为80 m80 m单元量子阱器件两种。利用傅里叶光谱仪对1#,2#样品进行77K液氮温度光谱响应测试。实验结果显示1#,2#样品峰值响应波长分别为8.43 m,8.32 m,与根据薛定谔方程得到器件理论峰值波长8.5 m间误差分别为1.0%,2.1%。实验结果说明MOCVD技术可以满足QWIP生长制备工艺要求,且器件电极压焊点位置与面积大小对器件峰值波长影响不大,而对峰值电流有一定影响。     

Persistent photo-conductance and photoquenching of selectively doped Al0.3Ga0.7As GaAs/heterojunctions

The dependence on photon energy of the persistent photoconductivity (PPC) in selectively doped high mobility Al_0.3Ga_0.7As—GaAs heterostructures has been measured at temperatures below 80 K. A decrease in conductivity due to light exposure at one wavelength after exposure to light at another wavelength — photo-quenching — is also found. It is concluded that deep centers in GaAs and AlGaAs other than the DX center in AlGaAs are mainly responsible for PPC.     

不同缓冲层对GaAs基In_(0.3)Ga_(0.7)As材料特性的影响

采用组分跳变和低温大失配缓冲层技术在GaAs衬底上外延了In0.3Ga0.7As材料。测试结果表明,采用组分跳变缓冲层生长的In0.3Ga0.7As主要依靠逐层间产生失配位错来释放应力,并导致表面形成纵横交错的Cross-hatch形貌;而采用低温大失配缓冲层技术则主要通过在低温缓冲层中形成大量缺陷来充分释放应力,并在后续外延的In0.3Ga0.7As表面没有与失配位错相关的Cross-hatch形貌出现。此外,仅需50nm厚的低温大失配缓冲层即可促使In0.3Ga0.7As中的应力完全释放,这种超薄缓冲层技术在工业批产中显得更为经济。     

120-nm gate-length In0.7Ga0.3As/In0.52Al0.48As InP-based HEMT

120 nm gate-length In_(0.7)Ga_(0.3)As/In_(0.52)Al_(0.48) As InP-based high electron mobility transitions(HEMTs) are fabricated by a new T-shaped gate electron beam lithograph(EBL) technology,which is achieved by the use of a PMMA/PMGI/ZEP520/PMGI four-layer photoresistor stack.These devices also demonstrate excellent DC and RF characteristics:the transconductance,maximum saturation drain-to-source current,threshold voltage,maximum current gain frequency,and maximum power-gain cutoff frequency of InGaAs/I...     

Influence of Ga vs As prelayers on GaAs/Ge growth morphology

The surface morphology of GaAs films grown on Ge substrates is studied by scanning force microscopy. We find a dramatic difference arising from Ga as opposed to As prelayers in the formation of anti-phase boundaries (APBs), surface features near threading dislocations, and surface roughness, for films as thick as 1 μm. Ga prelayer samples are smooth; thin films display some APBs with predominantly one growth domain while the 1 μm thick film displays the morphology of a homoepitaxial GaAs film. In contrast, As prelayer samples are rough with complicated APB structures, which can be attributed to the increase in single steps during As₂ deposition.     

Study of grown-in defects and effect of thermal annealing in Al0.3Ga0.7As and GaAs LPE layers

Studies of the grown-in deep-level defects in the undoped n-Al_xGa_1-xAs (x = 0.3) and GaAs epitaxial layers prepared by the liquid phase epitaxy (LPE) techniques have been made, using DLTS, I-V and C-V measurements. The effect of 300 °C thermal annealing on the grown-in defects was investigated as a function of annealing time. The results showed that significant reduction in these grown-in defects can be achieved via low temperature thermal annealing process. The main electron and hole traps observed in the Al_0.3Ga_0.7As LPE layer were due to the E_c-0.31 eV and E_v+0.18 eV level, respectively, while for the GaAs LPE layer, the electron traps were due to the E_c-0.42 and 0.60 eV levels, and the hole traps were due to E_v+0.40 and 0.71 eV levels. Research supported in part by the Air Force Wright Aeronautical Laboratories, Aeropropulsion Lab., Wright Patterson Air Force Base, Ohio, subcontract through SCEEE, contract F33615-81-C-2011, task-4, and in part by AFOSR grant no. 81-0187.     

Type I and Type II Alignment of the Light Hole Band in In0.15Ga0.85As/GaAs and in ln0.15Ga0.85As/Al0.15Ga0.85As Strained Quantum Wells

We present results of photoluminescence and cathodoluminescence measurements of strained undoped In_0.15Ga_0.85As/GaAs and In_0.15Ga_0.85As/Al_0.15Ga_0.85As quantum well structures, designed to throw light on the current controversy over light-hole band alignment at low In content. We compare these data with theoretical calculations of the confined state energies within the eight band effective mass approximation. Our analysis shows that for In_0.15Ga_0.85As/GaAs, the observed two transitions are consistent with either type I or type II alignment of the light hole band for band offset ratios within the accepted range. In the case of In_0.15Ga_0.85As/Al_0.15Ga_0.85As, however, our results clearly indicate type II alignment for the light hole band. We derive the band offset ratio Q, defined here as Q = δE_c/δE_g where δE_c is the conduction band offset and δE_g is the bandgap difference between the quantum well and the barrier in the presence of strain, for the In_0.15Ga_0.85As/Al_0.15Ga_0.85As system to be Q = 0.83 and discuss it in the context of the common anion rule.     

Effect of GaAs (100) substrate misorientation on the electrical parameters and surface morphology of metamorphic In0.7Al0.3As/In0.75Ga0.25As/In0.7Al0.3As HEMT nanoheterostructures

The results of studies of the effect of GaAs (100) substrate misorientation on the electrical parameters and surface morphology of high electron mobility In_0.7Al_0.3As/In_0.75Ga_0.25As/In_0.7Al_0.3As/GaAs nanoheterostructures are reported. Using molecular-beam epitaxy, two identical structures with a stepped compositional profile of the metamorphic In _x Al_{1 ? x} As (Δ _x = 0.05) buffer are grown on substrates of two types: a singular GaAs substrate with the orientation (100) ± 0.5° and a GaAs (100) substrate misoriented by (2 ± 0.5)° in the $\left[ {0\bar 1\bar 1} \right]$ direction. It is found that, in the case of the misoriented substrate, the concentration of the two-dimensional electron gas is ～40% higher. Broadening of the photoluminescence spectra and a shift of the peaks to lower photon energies, as experimentally observed in the case of the misoriented substrate, are attributed to the increased roughness of the heterointerfaces and strengthened fluctuations of the quantum-well width.     

Two electron transitions of the exciton bound at the Si Donor confined in GaAs/AlxGa1-xAs quantum wells

The exciton bound to the shallow Si-donor confined in a 100A wide GaAs quantum well has been studied in selective photoluminescence (SPL) and photoluminescence excitation (PLE) spectroscopy. The transition from the ground state, ls(Γ₆), to the first excited state, 2s(Γ₆), of the confined Si donor has been observed via two-electron transitions (TETs) of the donor bound exciton observed in SPL for the first time to the best of our knowledge. The interpretation of the TET peaks is confirmed by PLE measurements. Further, from Zeeman measurements, the magnetic field dependence of the donor ls(Γ₆)-2s(Γ₆) transition energy has been determined.     

调制掺杂Al_xGa_(1-x)As/GaAs异质结持久光电导的光谱响应

本文在77 K下研究了调制掺杂 n-Al_(0.3)Ga_(0.7)As/GaAs异质结持久光电导的光谱响应.结果表明,掺 Cr GaAs衬底中Cr深能级上电子的激发和 Al_xGa_(1-x)As中DX中心的光离化都产生持久光电导.     

High temperature MOVPE growth of GaAs/AlGaAs device structures with tertiarybutylarsine

The performance characteristics of epitaxial structures suitable for optoelectronic and electronic devices were investigated. These were fabricated by MOVPE using tertiary-butylarsine, a non-hydride arsenic source. Minority carrier diffusion lengths of 5μm at 3 × 10¹⁸/cm³ and 2μm at 2 × 10¹⁹/cm³ were achieved inp-type GaAs. Recombination velocities at the GaAs/AlGaAs interface are reduced to 1 × 10³ cm/sec by processing under appropriate conditions. Electron mobilities of 4000 cm²/V-sec inn-type (2 × 10¹⁷/cm³) layers resulted in transconductances of 120 mS/mm in 1.5μm gate depletion mode MESFETs. The above values are comparable to those obtained with arsine in this work and others reported in the literature.     

The structural dependence of light sensitivity in (Al,Ga)As/GaAs modulation doped heterostructures

Understanding the origin and nature of light sensitivity in (Al,Ga)As/GaAs modulation doped heterostructures is becoming important as modulation doped field effect transistors move from the research laboratories into practical application. Control of threshold voltage in an integrated circuit is crucial. If these devices are to be operated at cryogenic temperatures to take advantage of their enhanced transport properties then the persistent photoconductive effects associated with these structures cannot be ignored. This paper examines the dependence of light sensitivity on the thicknesses of the doped (Al, Ga)As layer and the undoped GaAs buffer layer. The use of As₂ as opposed to As₄ is investigated. Based upon these results, the origin and behavior of the persistent photoconductivity is reexamined.     

Diffusion of zinc into gaas through Al0.3Ga00.7As

The diffusion of zinc into GaAs, Al_0.3Ga_0.7As and Al_0.3Ga_0.7As/GaAs single heterostructures have been studied. The depth of the diffusion front is found to be proportional to the square root of the diffusion time, [t]^1/2, and for single heterostructures the Al_0.3Ga_0.7As layer thickness,d ₁ modifies this relationship through decreasing the junction depth byd ₁ multiplied by a constant. It is shown that this relationship can be used for predicting diffusion fronts in double heterostructures.