Enhanced power performance of enhancement-mode Al0.5Ga0.5As/In0.15Ga0.85As pHEMTs using alow-k BCB passivation

Surface passivation technology plays an important role, especially in E-mode pHEMTs applications, and a new passivation technology has been proposed in this study. This novel benzocyclobutene (BCB) passivation layer takes advantage of the low dielectric permittivity (2.7) and a low loss tangent (0.0008). In this letter, we not only suppress the gate-to-drain leakage current but also improve the device power performance under a high input power swing by using a BCB passivation layer. The passivated 1.0 μm-long gate pHEMTs exhibit a better off-state performance than the unpassivated ones. The maximum output power under a 2.4-GHz operation is 118 mW/mm, with a linear power gain of 11.1 dB and a power-added efficiency is 60%     

Fabrication of In0.25Ga0.75As/InGaAsPstrained SQW lasers on In0.05Ga0.95As ternarysubstrate

A uniform In_0.05Ga_0.95As ternary substrate was grown by using liquid encapsulated Czochralski (LEC) technique with a method of supplying GaAs source material at a constant temperature, and InGaAs/InGaAsP strained single quantum well (SQW) lasers were fabricated on the substrate for the first time. The lasers lased at 1.03 μm and exhibited low threshold current density of 222 A/cm² and excellent characteristic temperature of 221 K, showing that the ternary substrate has a sufficient quality for laser fabrication     

High-performance In0.52Al0.48As/In0.53Ga0.47As HFET compatible with optical-detectorintegration

The authors report the successful demonstration of a 1.0-μm gate InAlAs/InGaAs heterojunction FET (HFET) on top of thick InGaAs layers using lattice-matched molecular beam epitaxy (MBE). This scheme is compatible with metal-semiconductor-metal (MSM) photodetector fabrication. The authors measured the performance of InAlAs/InGaAs HFETs from 0 to 40 GHz. Device performance is characterized by peak extrinsic transconductances of 390 mS/mm and as-measured cutoff frequencies up to 30 GHz for a nominal 1.0-μm-gate-length HFET. HFET device measurements are compared for samples growth with and without the thick underlying InGaAs optical-detector absorbing layer     

60-GHz pseudomorphicAl0.25Ga0.75As/In0.28Ga0.72As low-noise HEMTs

V-band low-noise planar-doped pseudomorphic (PM) InGaAs high electron mobility transistors (HEMTs) were fabricated with an indium mole fraction of 28% in the InGaAs channel. A device with 0.15-μm T-gate achieved a minimum noise figure of 1.5 dB with an associated gain of 6.1 dB at 61.5 GHz     

Hot-electron transport in In0.53Ga0.47As

A set of physical constants for In_0.53Ga_0.47As as required for transport calculations is obtained by reviewing the literature. Velocities for fields up to 100 kV/cm, calculated by the Monte Carlo method using these constants, are presented for the temperatures of 95 and 300 K. The calculated values are found to be in good agreement with the available experimental results.     

Metamorphic In0.4Al0.6As/In0.4Ga0.6As HEMTs on GaAs substrate

New In_0.4Al_0.6As/In_0.4Ga_0.6 As metamorphic (MM) high electron mobility transistors (HEMTs) have been successfully fabricated on GaAs substrate with T-shaped gate lengths varying from 0.1 to 0.25 μm. The Schottky characteristics are a forward turn-on voltage of 0.7 V and a gate breakdown voltage of -10.5 V. These new MM-HEMTs exhibit typical drain currents of 600 mA/mm and extrinsic transconductance superior to 720 mS/mm. An extrinsic current cutoff frequency f_T of 195 GHz is achieved with the 0.1-μm gate length device. These results are the first reported for In_0.4 Al_0.6As/In_0.4Ga_0.6As MM-HEMTs on GaAs substrate     

120nm栅长In0.7Ga0.3As/In0.52Al0.48As HEMTs 器件

利用新型的PMMA/PMGI/ZEP520/PMGI四层胶T形栅电子束光刻技术制备出120nm栅长InP基雁配In0.7Ga0.3As/In0.52Al0.48As 高电子迁移率晶体管。制作出的InP基HEMT器件获得了良好的直流和高频性能,跨导、饱和漏电流密度、阈值电压、电流增益截止频率和最大单向功率增益频率分别达到520 mS/mm, 446 mA/mm, -1.0 V, 141 GHz 及 120 GHz。文中的材料结构和所有器件制备均为本研究小组自主研究开发。     

Buried-Pt gate InP/In0.52Al0.48As/In0.7Ga0.3As pseudomorphic HEMTs

InP-based high electron mobility transistors (HEMTs) were fabricated by depositing Pt-based multilayer metallization on top of a 6-nm-thick InP etch stop layer and then applying a post-annealing process. The performances of the fabricated 55-nm-gate HEMTs before and after the post-annealing were characterized and were compared to investigate the effect of the penetration of Pt through the very thin InP etch stop layer. After annealing at 250 °C for 5 min, the extrinsic transconductance (G_m) was increased from 1.05 to 1.17 S/mm and Schottky barrier height was increased from 0.63 to 0.66 eV. The unity current gain cutoff frequency (f_T) was increased from 351 to 408 GHz, and the maximum oscillation frequency (f_max) was increased from 225 to 260 GHz. These performance improvements can be attributed to penetration of the Pt through the 6-nm thick InP layer, and making contact on the InAlAs layer. The STEM image of the annealed device clearly shows that the Pt atoms contacted the InAlAs layer after penetrating through the InP layer.     

In0.53Ga0.47As/In0.52Al0.48As雪崩光电二极管的数值模拟研究

建立了SACM型In0.53Ga0.47As/In0.52Al0.48As雪崩光电二极管(APD)的分析模型,通过数值研究和理论分析设计出高性能的In0.53Ga0.47As/In0.52Al0.48As APD。器件设计中,一方面添加了In0.52Al0.48As势垒层来阻挡接触层的少数载流子的扩散,进而减小暗电流的产生;另一方面,雪崩倍增区采用双层掺杂结构设计,优化了器件倍增区的电场梯度分布。最后,利用ATLAS软件较系统地研究并分析了雪崩倍增层、电荷层以及吸收层的掺杂水平和厚度对器件电场分布、击穿电压、IV特性和直流增益的影响。优化后APD的单位增益可以达到0.9 A/W,在工作电压(0.9 Vb)下增益为23.4,工作暗电流也仅是纳安级别(@0.9 Vb)。由于In0.52Al0.48As材料的电子与空穴的碰撞离化率比InP材料的差异更大,因此器件的噪声因子也较低。     

A resistive-gate In0.53Ga0.47As/InPheterostructure CCD

The first InGaAs/InP charge-coupled device (CCD) is demonstrated, exhibiting a charge transfer efficiency (CTE) of 0.98 at 13 MHz and 1 GHz. Cooling the device improves the CTE to greater than 0.99 at 13-MHz clock frequency. The 0.76-eV In_0.53Ga_0.47As bandgap makes this structure applicable to direct-detection short-wavelength infrared (SWIR) imagers     

Characterization of surface-undoped In0.52Al0.48As/In0.53Ga0.47As/InP high electron mobilitytransistors

High-performance 0.3-μm-gate-length surface-undoped In_0.52 Al_0.48As/In_0.53Ga_0.47As/InP high-electron-mobility transistors (HEMTs) grown by molecular beam epitaxy (MBE) have been characterized and compared with a surface-doped structure. At 18 GHz, the surface-undoped HEMT has achieved a maximum stable gain (MSG) of 19.2 dB compared to 16.0 dB for the surface-doped structure. The higher MSG value of the surface-undoped HEMTs is obtained due to the improved g_m/g₀ ratio associated with the surface-induced electric field spreading effect. Comparison of identical 0.3-×150-μm-gate devices fabricated on surface-undoped and -doped structures has shown greatly improved gate leakage characteristics and much lower output conductance for the surface-undoped structure. It is demonstrated that the surface potential, modulated by different surface layer designs, affects the charge control in the conducting channel, especially the carrier injection into the buffer, resulting in excess output conductance. Several millimeter-wave coplanar waveguide (CPW) monolithic distributed amplifiers have been successfully fabricated by using the surface-undoped HEMT structure. A high gain per stage distributed amplifier with 170-dB±1-dB small-signal gain across a frequency band of 24-40 GHz, a W-band monolithic integrated circuit with 6.4-dB gain at 94 GHz, and a broad bandwidth distributed amplifier with 5-dB gain across a frequency band of 5 to 100 GHz have been demonstrated by using the surface-undoped structures     

In0.52Al0.48As/In0.53Ga0.47As double-heterojunction p-n-p bipolar transistors grown bymolecular beam epitaxy

P-n-p In_0.52Al_0.48As/In_0.53Ga_0.47 As double-heterojunction bipolar transistors with a p⁺-InAs emitter cap layer grown by molecular-beam epitaxy have been realized and tested. A five-period 15-Å-thick In_0.53Ga_0.47As/InAs superlattice was incorporated between the In_0.53Ga_0.47As and InAs cap layer to smooth out the valence-band discontinuity. Specific contact resistance of 1×10^-5 and 2×10^-6 Ω-cm² were measured for nonalloyed emitter and base contacts, respectively. A maximum common emitter current gain of 70 has been measured for a 1500-Å-thick base transistor at a collector current density of 1.2×10³ A/cm². Typical current gains of devices with 50×50-μm² emitter areas were around 50 with ideality factors of 1.4     

Band offsets of In0.30Ga0.70As/In0.29Al0.71As heterojunction grown on GaAs substrate

Temperature-dependent current-voltage measurement was employed to study the band offsets of the In_0.30Ga_0.70As/In _0.29Al_0.71As heterojunction. The conduction band discontinuity was determined to be 0.71±0.05 eV which corresponds to a conduction band offset to bandgap difference ratio ~0.66. The comparison between experimental and theoretical results is presented     

Fabrication of 80-nm T-gate high indium In0.7Ga0.3As/In0.6Ga0.4As composite channels mHEMT on GaAs substrate with simple technological process

An 80-nm gate length metamorphic high electron mobility transistor (mHEMT) on a GaAs substrate with high indium composite compound-channels In_0.7Ga_0.3As/In_0.6Ga_0.4As and an optimized grade buffer scheme is presented. High 2-DEG Hall mobility values of 10200 cm²/(V· s) and a sheet density of 3.5 × 10¹² cm^-2 at 300 K have been achieved. The device's T-shaped gate was made by utilizing a simple three layers electron beam resist, instead of employing a passivation layer for the T-share gate, which is beneficial to decreasing parasitic capacitance and parasitic resistance of the gate and simplifying the device manufacturing process. The ohmic contact resistance R_c is 0.2 Ω ·mm when using the same metal system with the gate (Pt/Ti/Pt/Au), which reduces the manufacturing cycle of the device. The mHEMT device demonstrates excellent DC and RF characteristics. The peak extrinsic transconductance of 1.1 S/mm and the maximum drain current density of 0.86 A/mm are obtained. The unity current gain cut-off frequency (f_T) and the maximum oscillation frequency (f_max) are 246 and 301 GHz, respectively.     

Backgating in pseudomorphic In0.15Ga0.85As/Al0.25Ga0.75As MODFET's with a GaAs:Er buffer layer

A new GaAs:Er buffer layer grown by MBE has been developed which significantly reduces backgating currents (by 3 to 4 orders of magnitude) in pseudomorphic InGaAs/AlGaAs modulation-doped field effect transistors (MODFET's). The buffer layer is highly resistive, in the 10 ²-10⁵ Ω·cm range over the Er-doping range investigated. Presence of internal Schottky barriers resulting from high-density ErAs precipitates has been proposed to he the cause of the high resistivity     

Tunneling between two quantum wells: In0.53Ga0.47As/InP versus GaAs/Al0.35Ga0.65As

The electron transfer from a narrow to a wide quantum well through a thin barrier is studied in the non-resonant case by time-resolved photoluminescence. The two systems In_0.53Ga_0.47As/InP and GaAs/Al_0.35Ga_0.65As are compared. Space charge effects are investigated and discussed. Contributions of holes to the tunneling process are determined.     

Unstrained, modulation-doped, In0.3Ga0.7As/In0.29Al0.71As field-effect transistor grown on GaAssubstrate

The fabrication, structure, and properties of unstrained modulation-doped, 1-μm-long and 10-μm-wide gate, field effect transistors made of In_0.3Ga_0.7As/In_0.29As_0.71As heterojunctions grown on GaAs substrates using compositionally step-graded buffer layers are described. These devices have a transconductance of 335 mS/mm, f_max of 56 GHz, and a gate breakdown voltage of 23.5 V     

Electron transport in 0.15-μm gate In0.52Al0.48As/In0.53Ga0.47As HEMT

Magneto-transport and cyclotron resonance measurements were made to determine directly the density, mobility, and the effective mass of the charge carriers in a high-performance 0.15-μm gate In_0.52 Al_0.48As/In_0.53Ga_0.47As high-electron-mobility transistor (HEMT) at low temperatures. At the gate voltage V_G=0 V, the carrier density n _g under the gate is 9×10¹¹ cm^-2, while outside of the gate region n_g=2.1×10¹² cm^-2. The mobility under the gate at 4.2 K is as low as 400 cm²/V-s when V_G<0.1 V and rapidly approaches 11000 cm²/V-s when V_G>0.1 V. The existence of this high mobility threshold is crucial to the operation of the device and sets its high-performance region in V_G>0.1 V     

High-frequency submicrometerAl0.48In0.52As/In0.53Ga0.47As heterostructure bipolar transistors

The high speed scaling of an Al_0.48In_0.52As/In_0.53Ga_0.47 As submicrometer heterostructure bipolar transistor (HBT) is presented. Transistors with emitter dimensions of 0.5×11 and 3.5×3.5 μm² exhibit unity current-gain cutoff frequencies of 63 and 70 GHz, respectively. Emitter current density greater than 3.3×10⁵ A/cm² is demonstrated in a submicrometer AlInAs/InGaAs HBT. The analysis shows that the device speed is limited by the parasitic collector charging time     

Single- and double-heterojunction pseudomorphic In0.5(Al0.3Ga0.7)0.5P/In0.2Ga0.8As high electron mobility transistors grown by gas sourcemolecular beam epitaxy

In_0.5(Al_0.3Ga_0.7)_0.5 P/In_0.2Ga_0.8As single- and double-heterojunction pseudomorphic high electron mobility transistors (SH-PHEMTs and DH-PHEMTs) on GaAs grown by gas-source molecular beam epitaxy (GSMBE) were demonstrated for the first time. SH-PHEMTs with a 1-μm gate-length showed a peak extrinsic transconductance g_m of 293 mS/mm and a full channel current density I_max of 350 mA/mm. The corresponding values of g_m and I_max were 320 mS/mm and 550 mA/mm, respectively, for the DH-PHEMTs. A short-circuit current gain (H₂₁) cutoff frequency f_T of 21 GHz and a maximum oscillation frequency f_max of 64 GHz were obtained from a 1 μm DH device. The improved device performance is attributed to the large ΔE_c provided by the In_0.5(Al_0.3Ga_0.7)_0.5P/In _0.2Ga_0.8As heterojunctions. These results demonstrated that In_0.5(Al_0.3Ga_0.7)_0.5P/In _0.2Ga_0.8As PHEMT's are promising candidates for microwave power applications