A comparison of CMOS circuit techniques: differential cascode voltage switch logic versus conventional logic

Differential cascode voltage switch (DCVS) logic is a CMOS circuit technique that has potential advantages over conventional NAND/NOR logic in terms of circuit delay, layout density, power dissipation, and logic flexibility. A detailed comparison of DCVS logic and conventional logic is carried out by simulation, using SPICE, of the performance of full adders designed using the different circuit techniques. The parameters compared are: input gate capacitance, number of transistors required, propagation delay time, and average power dissipation. In the static case, DCVS appears to be superior to full CMOS in regards to input capacitance and device count but inferior in regards to power dissipation. The speeds of the two technologies are similar. In the dynamic case, DCVS can be faster than more conventional CMOS dynamic logic, but only at the expense of increased device count and power dissipation.     

Floating-body effects in partially depleted SOI CMOS circuits

This paper presents a detailed study on the impact of a floating body in partially depleted (PD) silicon-on-insulator (SOI) MOSFET's on various CMOS circuits. Digital very large scale integration (VLSI) CMOS circuit families including static and dynamic CMOS logic, static cascade voltage switch logic (static CVSL), and dynamic cascade voltage switch logic (dynamic CVSL) are investigated with particular emphasis on circuit topologies where the parasitic bipolar effect resulting from the floating body affects the circuit operation and stability. Commonly used circuit building blocks for fast arithmetic operations in processor data-flow, such as static and dynamic carry lookahead circuits and Manchester carry chains, are examined. Pass-transistor-based designs including latch, multiplexer, and pseudo two-phase dynamic logic are then discussed. It is shown that under certain circuit topologies and switching patterns, the parasitic bipolar effect causes extra power consumption and degrades the noise margin and stability of the circuits. In certain dynamic circuits, the parasitic bipolar effect is shown to cause logic state error if not properly accounted for     

Dual-threshold voltage assignment with transistor sizing for lowpower CMOS circuits

We demonstrate a novel algorithm for assigning the threshold voltage to the gates in a digital random logic complementary metal-oxide-semiconductor (CMOS) circuit for a dual-threshold voltage process. The tradeoff between static and dynamic power consumption has been explored. When used along with device sizing and supply voltage reduction techniques for low power, the proposed algorithm can reduce the total power dissipation of a circuit by as much as 50%     

LSI implementation of a low-power 4×4-bit array two-phase clocked adiabatic static CMOS logic multiplier

As the density and operating speed of complementary metal oxide semiconductor (CMOS) circuits increases, dynamic power dissipation has become a critical concern in the design and development—of personal information systems and large computers. The reduction of supply voltage, node capacitance, and switching activity are common approaches used in conventional CMOS. In adiabatic switching circuits, the current flow through transistors can be significantly reduced by ensuring uniform charge transfer over the entire available time. This paper presents the simulation of this current in two-phase clocked adiabatic static CMOS logic (2PASCL) and conventional CMOS. From the SPICE simulations, at transition frequencies from 1 to 12 MHz, a 4×4-bit array 2PASCL multiplier shows a maximum reduction in power dissipation of 77% relative to that of a static CMOS. The measurement results of a 4×4-bit array 2PASCL multiplier demonstrate a 57% reduction compared to a 4×4-bit array two-phase clocked adiabatic dynamic CMOS logic (2PADCL). These results indicate that 2PASCL technology can be advantageous when applied to low-power digital devices operated at low frequencies, such as radio-frequency identification (RFID) tags, smart cards, and sensors.     

Complementary ferroelectric-capacitor logic for low-power logic-in-memory VLSI

A novel nonvolatile logic style, called complementary ferroelectric-capacitor (CFC) logic, is proposed for low-power logic-in-memory VLSI, in which storage elements are distributed over the logic-circuit plane. Standby currents in distributed storage elements can be cut off by using ferroelectric-based nonvolatile storage elements, and the standby power dissipation can be greatly reduced. Since the nonvolatile storage and the switching functions are merged into ferroelectric capacitors by the capacitive coupling effect, reduction of active device counts can be achieved. The use of complementary stored data in coupled ferroelectric capacitors makes it possible to perform a switching operation with small degradation of the nonvolatile charge at a low supply voltage. The restore operation can be performed by only applying the small bias across the ferroelectric capacitor, which reduces the dynamic power dissipation. Applying the proposed circuitry in a fully parallel 32-bit content-addressable memory results in about 2/3 dynamic power reduction and 1/7700 static power reduction with chip size of 1/3, compared to a CMOS implementation using 0.6-/spl mu/m ferroelectric/CMOS.     

Skewed CMOS: noise-tolerant high-performance low-power static circuit family

In this paper, we present a noise-tolerant high-performance static circuit family suitable for low-voltage operation called skewed logic. Skewed logic circuits in comparison with Domino logic have better scalability and are more suitable for low voltage applications because of better noise margins. Skewed logic and its variations have been compared with Domino logic in terms of delay, power, and dynamic noise margin. A design methodology for skewed CMOS pipelined circuits has been developed. To demonstrate the applicability of the proposed logic style, 0.35 /spl mu/m 5.56 ns CMOS 16/spl times/16 bit multipliers have been designed using skewed logic circuits and fabricated through MOSIS. Measurement results show that the multiplier only consumed a power of 195 mW due to its low clock load.     

LVDCSL: a high fan-in, high-performance, low-voltage differentialcurrent switch logic family

This paper presents a low voltage differential current switch logic (LVDCSL) gate capable of achieving high performance for large fan-in gates. High fan-in is enabled by using a large height predischarged N-channel metal-oxide-semiconductor (NMOS) trees. The power penalty of an increased number of internal nodes in the gate is mitigated by restricting their voltage swings. The salient features of this low-voltage DCSL family are high speed for high fan-in large stack height NMOS trees, low power due to restricted internal voltage swings, simple interface to static complementary metal-oxide-semiconductor (CMOS), and a latching nature which locks out inputs once outputs are evaluated. Results show that LVDCSL is capable of working at under 2 V in a 0.35% CMOS process while being faster than comparable Domino gates. At the same time total power consumption is reduced. LVDCSL achieves 40% delay improvement and 22% power reduction in comparison with dual rail Domino gates for 8 bit carry look-ahead circuits. Results for the critical path of an adder reveal that the complexity afforded by the gate, effectively decreases the number of logic levels and leads to improved performance     

Design and application of pipelined dynamic CMOS ternary logic andsimple ternary differential logic

Dynamic CMOS ternary logic circuits that can be used to form a pipelined system with nonoverlapped two-phase clocks are proposed and investigated. The proposed dynamic ternary gates do not dissipate DC power and have full voltage swings. A circuit structure called the simple ternary differential logic (STDL) is also proposed and analyzed, and an optimal procedure is developed. An experimental chip has been fabricated in a 1.2-μm CMOS process and tested. A binary pipelined multiplier has been designed, using the proposed dynamic ternary logic circuits in the interior of the multiplier for coding of radix-2 redundant positive-digit number. The structure has the advantages of higher operating frequency, less latency, and lower device count as compared with the conventional binary parallel pipelined multiplier. The advantages of the circuits over other dynamic ternary logic circuits are shown     

Energy-efficient skewed static logic with dual Vt: design and synthesis

In this paper, we describe skewed static logic (S/sup 2/L) with topology-dependent dual Vt which exhibits an energy-efficient operation. S/sup 2/L consumes less dynamic and static power compared to monotonic static (MS) CMOS. Speed degradation of S/sup 2/L, if any, can be offset by an accelerator circuit. We have designed NAND-NOR gate chains using 0.18-/spl mu/m CMOS technology and verified that S/sup 2/L reduces energy-delay product over MS CMOS by 27%-50%. We have also designed 32-b carry-lookahead adders and verified that S/sup 2/L with dual Vt reduces delay by 43% and energy-delay product by 31% for 1-V power supply over conventional CMOS circuit. Synthesis algorithm for S/sup 2/L is developed and the experimental results show S/sup 2/L consumes 23% less power than MS CMOS with minor increase in delay.     

Noncomplementary BiCMOS logic and CMOS logic for low-voltage,low-power operation-a comparative study

This paper presents results of a comprehensive comparative study of six bipolar complementary metal-oxide-semiconductor (BiCMOS) noncomplementary logic design styles and two CMOS logic styles for low-voltage, low-power operation. These logic styles have been compared for switching power consumption and power efficiency (power-delay product). The examination offers two alternative approaches never used in other comparative studies. First, all BiCMOS-based styles are compared to low-power CMOS styles as opposed to a single conventional static CMOS style. Second, a low-power methodology has been used as opposed to performance methodology referred to in the previous logic comparisons. The styles examined are bootstrapped BiCMOS, bootstrapped full-swing BiCMOS, bootstrapped bipolar CMOS, Seng-Rofail's bootstrapped BiCMOS, modified full-swing BiCMOS, dynamic full-swing BiCMOS, double pass-transistor CMOS, and inverter-based CMOS. These design styles have been compared at various power supply voltages (0.9-3 V), with various output load capacitances (0.1-1 pF) at the frequency 50 MHz and temperature 27°C. The results clearly show which logic style is the most beneficial for which specific conditions     

Robust subthreshold logic for ultra-low power operation

Digital subthreshold logic circuits can be used for applications in the ultra-low power end of the design spectrum, where performance is of secondary importance. In this paper, we propose two different subthreshold logic families: 1) variable threshold voltage subthreshold CMOS (VT-Sub-CMOS) and 2) subthreshold dynamic threshold voltage MOS (Sub-DTMOS) logic. Both logic families have comparable power consumption as regular subthreshold CMOS logic (which is up to six orders of magnitude lower than that of normal strong inversion circuit) with superior robustness and tolerance to process and temperature variations than that of regular subthreshold CMOS logic     

A power efficient 26-GHz 32:1 static frequency divider in 130-nm bulk CMOS

A 32:1 static frequency divider consisting of five stages of 2:1 dividers using current mode logic (CML) was fabricated in a 130-nm bulk complementary metal-oxide semiconductor (CMOS) logic process. By optimizing transistors size, high operating speed is achieved with limited power consumption. For an input power of 0dBm, the 32:1 divider operates up to 26GHz with a 1.5-V supply voltage. The whole 32:1 chain including buffers consumes 8.97mW and the first stage consumes only 3.88mW at a 26-GHz operation. The power consumption of the first 2:1 stage is less than 15% of other bulk CMOS static frequency dividers operating at the same frequency.     

A Novel Overlap-Based Logic Cell: An Efficient Implementation of Flip–Flops With Embedded Logic

This paper presents several efficient architectures of dynamic/static edge-triggered flip–flops with a compact embedded logic. The proposed structure, which benefits from the overlap period, fixes most of the drawbacks of the dynamic logic family. The design issues of setting the appropriate overlap period for this architecture are explained. The proposed overlap-based approach is compared with several state-of-the-art dynamic/static logic styles in implementing a 4-bit shift register and an odd–even sort coprocessor using different CMOS technologies. The simulation results showed that the overlap-based logic cells become much more efficient when the complexity of their embedded logic function increases. Moreover, this approach improves static power consumption, which makes it even more efficient in below 0.18 $ muhbox{m}$ CMOS technologies.      

MOSFET-like CNFET based logic gate library for low-power application: a comparative study

The next generation of logic gate devices are expected to depend upon radically new technologies mainly due to the increasing difficulties and limitations of existing CMOS technology. MOSFET like CNFETs should ideally be the best devices to work with for high-performance VLSI. This paper presents results of a comprehensive comparative study of MOSFET-like carbon nanotube field effect transistors (CNFETs) technology based logic gate library for high-speed, low-power operation than conventional bulk CMOS libraries. It focuses on comparing four promising logic families namely: complementary-CMOS (C-CMOS), transmission gate (TG), complementary pass logic (CPL) and Domino logic (DL) styles are presented. Based on these logic styles, the proposed library of static and dynamic NAND-NOR logic gates, XOR, multiplexer and full adder functions are implemented efficiently and carefully analyzed with a test bench to measure propagation delay and power dissipation as a function of supply voltage. This analysis provides the right choice of logic style for low-power, high-speed applications. Proposed logic gates libraries are simulated using Synopsys HSPICE based on the standard 32 nm CNFET model. The simulation results demonstrate that, it is best to use C-CMOS logic style gates that are implemented in CNFET technology which are superior in performance compared to other logic styles, because of their low average power-delay-product (PDP). The analysis also demonstrates how the optimum supply voltage varies with logic styles in ultra-low power systems. The robustness of the proposed logic gate library is also compared with conventional and state-art of CMOS logic gate libraries.     

Design for concurrent error detection and testability instorage/logic arrays

Storage/Logic Arrays (SLA's) represent a structured logic array approach to the design of VLSI sequential logic. Design for concurrent error detection and testability is complicated in these arrays by the presence of embedded memory elements and multiple levels of logic. A means of designing SLA's for ease of testability and concurrent error detection (CED) is provided in this paper. Test sets for static and dynamic CMOS circuits are described. Fault and error coverage is presented and performance and area costs are analyzed for example circuits. In addition, a means of implementing dynamic CMOS SLA's is presented and shown superior to previous NMOS, static CMOS, and dynamic CMOS approaches based upon power consumption and simplicity of design     

On circuit techniques to improve noise immunity of CMOS dynamic logic

Dynamic CMOS logic circuits are widely employed in high-performance VLSI chips in pursuing very high system performance. However, dynamic CMOS gates are inherently less resistant to noises than static CMOS gates. With the increasing stringent noise requirement due to aggressive technology scaling, the noise tolerance of dynamic circuits has to be first improved for the overall reliable operation of VLSI chips designed using deep submicron process technology. In the literature, a number of design techniques have been proposed to enhance the noise tolerance of dynamic logic gates. An overview and classification of these techniques are first presented in this paper. Then, we introduce a novel noise-tolerant design technique using circuitry exhibiting a negative differential resistance effect. We have demonstrated through analysis and simulation that using the proposed method the noise tolerance of dynamic logic gates can be improved beyond the level of static CMOS logic gates while the performance advantage of dynamic circuits is still retained. Simulation results on large fan-in dynamic CMOS logic gates have shown that, at a supply voltage of 1.6 V, the input noise immunity level can be increased to 0.8 V for about 10% delay overhead and to 1.0 V for only about 20% delay overhead.     

QSERL: quasi-static energy recovery logic

A new quasi-static energy recovery logic family (QSERL) using the principle of adiabatic switching is proposed in this paper. Most of the previously proposed adiabatic logic styles are dynamic and require complex clocking schemes. The proposed QSERL uses two complementary sinusoidal supply clocks and resembles the behavior of static CMOS. Thus, switching activity is significantly lower than dynamic logic. In addition, QSERL circuits can be directly derived from static CMOS circuits. A high-efficiency clock generation circuitry, which generates two complementary sinusoidal clocks compatible to QSERL, is also presented in this paper. The adiabatic clock circuitry locks the frequency of clock signals, which makes it possible to integrate adiabatic modules into a VLSI system. We have designed an 8×8 carry-save multiplier using QSERL logic and two phase sinusoidal clocks. SPICE simulation shows that the QSERL multiplier can save 34% of energy over static CMOS multiplier at 100 MHz     

A minimum total power methodology for projecting limits on CMOS GSI

A circuit design methodology minimizing total power drain of a static complementary metal-oxide-semiconductor (CMOS) random logic network for a prescribed performance, operating temperature range, and short channel threshold voltage rolloff is investigated. Physical, continuous, smooth, and compact “transregional” MOSFET drain current models that consider high-field effects in scaled devices and permit tradeoffs between saturation drive current and subthreshold leakage current are employed to model CMOS circuit performance and power dissipation at low voltages. Transregional models are used in conjunction with physical short channel MOSFET threshold voltage rolloff models and stochastic interconnect distributions to project optimal supply voltages, threshold voltages, and device channel widths minimizing total power dissipated by CMOS logic circuits for each National Technology Roadmap for Semiconductors (NTRS) technology generation. Optimum supply voltage, corresponding to minimum total power dissipation, is projected to scale to 510 mV for the 50-nm 10-GHz CMOS generation in the year 2012. Techniques exploiting datapath parallelism to further scale the supply voltage are shown to offer decreasing reductions in power dissipation with technology scaling     

Leakage Current Reduction Using Subthreshold Source-Coupled Logic

The performance of subthreshold source-coupled logic (STSCL) circuits for ultra-low-power applications is explored. It is shown that the power consumption of STSCL circuits can be reduced well below the subthreshold leakage current of static CMOS circuits. STSCL circuits exhibit a better power–delay performance compared with their static CMOS counterparts in situations where the leakage current constitutes a significant part of the power dissipation of static CMOS gates. The superior control on power consumption, in addition to the lower sensitivity to the process and supply voltage variations, makes the STSCL topology very suitable for implementing ultra-low-power low-frequency digital systems in modern nanometer-scale technologies. An analytical approach for comparing the power–delay performance of these two topologies is proposed.      

LECTOR: a technique for leakage reduction in CMOS circuits

In CMOS circuits, the reduction of the threshold voltage due to voltage scaling leads to increase in subthreshold leakage current and hence static power dissipation. We propose a novel technique called LECTOR for designing CMOS gates which significantly cuts down the leakage current without increasing the dynamic power dissipation. In the proposed technique, we introduce two leakage control transistors (a p-type and a n-type) within the logic gate for which the gate terminal of each leakage control transistor (LCT) is controlled by the source of the other. In this arrangement, one of the LCTs is always "near its cutoff voltage" for any input combination. This increases the resistance of the path from V/sub dd/ to ground, leading to significant decrease in leakage currents. The gate-level netlist of the given circuit is first converted into a static CMOS complex gate implementation and then LCTs are introduced to obtain a leakage-controlled circuit. The significant feature of LECTOR is that it works effectively in both active and idle states of the circuit, resulting in better leakage reduction compared to other techniques. Further, the proposed technique overcomes the limitations posed by other existing methods for leakage reduction. Experimental results indicate an average leakage reduction of 79.4% for MCNC'91 benchmark circuits.