Propagation simulation and dilatancy analysis of rock joint using displacement discontinuity method简

A revised displacement discontinuity method （DDM） program is developed for the simulation of rock joint propagation and dilatancy analysis. The non-linear joint model used in the program adopts Barton-Bandis normal deformation model, Kulhaway shear deformation model and Mohr-Coulomb criterion. The joint propagation criterion is based on the equivalent stress intensity factor which can be obtained by regression analysis. The simulated rock joint propagation accords well with the existing knowledge. The closure and opening ofj oint is investigated by DDM, and it is shown that if the opening volume of propagated joint is larger than closure volume of the old joint, the joint dilatancy occurs. The dilatancy condition is mainly controlled by the normal stiffness of the rock joint. When the normal stiffness is larger than the critical value, joint dilatancy occurs. The critical normal stiffness of rock joint changes with the joint-load angle, and joint dilatancy is most possible to occur at 30°.     

Numerical simulation and optimization of red mud separation thickener with self-dilute feed简

In order to acquire the flow pattern and investigate the settling behavior of the red mud in the separation thickener, computational fluid dynamics （CFD）, custom subroutines and agglomerates settling theory were employed to simulate the three-dimensional flow field in an industrial scale thickener with the introduction of a self-dilute feed system. The simulation results show good agreement with the measurement onsite and the flow patterns of the thickener are presented and discussed on both velocity and concentration field. Optimization experiments on feed well and self-dilute system were also carried out, and indicate that the optimal thickener system can dilute the solid concentration in feed well from 110 g/L to 86 g/L which would help the agglomerates＇ formation and improve the red mud settling speed. Furthermore, the additional power of recirculation pump can be saved and flocculants dosage was reduced from 105g/t to 85g/t in the operation.     

Structural-acoustic coupling characteristics of honeycomb sandwich plate based on parameter sensitivity analysis简

The structural-acoustic coupling model for isotropic thin elastic plate was extended to honeycomb sandwich plate （HSP） by applying Green function method. Then an equivalent circuit model of the weakly-strongly coupled system was proposed. Based on that, the estimation formulae of the coupled eigenfrequency were derived. The accuracy of the theoretical predictions was checked against experimental data, with good agreement achieved. Finally, the effects of HSP design parameters on the system coupling degree, the acoustic cavity eigenfrequency, and sound pressure response were analyzed. The results show that mechanical and acoustical characteristics of HSP can be improved by increasing the thickness of face sheet and reducing the mass density of material.     

Dynamic assets allocation based on market microstructure model with variable-intensity jumps简

In order to characterizc large fluctuations of the financial markets and optimize financial portfolio, a new dynamic asset control strategy was proposed in this work. Firstly, a random process item with variable jump intensity was introduced to the existing discrete microstructure model to denote large price fluctuations. The nonparametric method of LEE was used for detecting jumps. Further, the extended Kalman filter and the maximum likelihood method were applied to discrete microstructure modeling and the estimation of two market potential variables： market excess demand and liquidity. At last, based on the estimated variables, an assets allocation strategy using evolutionary algorithm was designed to control the weight of each asset dynamically. Case studies on IBM Stock show that jumps with variable intensity are detected successfully, and the assets allocation strategy may effectively keep the total assets growth or prevent assets loss at the stochastic financial market.     

Characteristics and formation of high quality reservoirs in sediment gravity flows of Gangzhong area,Huanghuadepression简

Reservoirs can be developed in the sediment gravity flows.However,high quality reservoirs are found widespread in sediment gravity flows of Gangzhong area,Huanghua depression,Bohai Bay Basin,East China.Characteristics and formation of these reservoirs are key problems to be solved.Through comprehensive analysis of thin section petrography,scanning electron microscopy and X-ray diffraction,two distinct rules were obtained.1） These high quality reservoirs have apparent characteristics：lithology consists mainly of medium-fine grained sands; moderately-well sorted and rounded; intergranular pores dominating 70% of the entire pores,surface per unit pore volume reaches 15%; average porosity is 21% and average permeability is 55×10-3 μm2.2） Types of sedimentary microfacies and dissolution strongly control on the formation of high quality reservoirs.Main channels and sandy braided bars have the best reservoir properties.Because that sediments are mainly medium-fine grained sands in high-energy environments.The favorable primary porosity and permeability may promote calcite cementation and help to produce more secondary pores.Besides,at the depth of 2500-3200 m,basically matching threshold of oil generation,organic acid expelled when organic matter became mature,and H＋ released during clay mineral transformation.These both result in the dissolution of calcite cements and create large volume pores,then physical properties improve correspondingly.Moreover,deep hydrothermal fluid intrusion may also have impacts on the development of secondary pores.     

Identification on rock and soil parameters for vibration drilling rock in metal mine based on fuzzy least square support vectormachine简

A single freedom degree model of drilling bit-rock was established according to the vibration mechanism and its dynamic characteristics. Moreover, a novel identification method of rock and soil parameters for vibration drilling based on the fuzzy least squares （FLS）-support vector machine （SVM） was developed, in which the fuzzy membership function was set by using linear distance, and its parameters, such as penalty factor and kernel parameter, were optimized by using adaptive genetic algorithm. And FLS-SVM identification on rock and soil parameters for vibration drilling was made by changing the input/output data from single freedom degree model of drilling bit-rock. The results of identification simulation and resonance column experiment show that relative error of natural frequency for some hard sand from identification simulation and resonance column experiment is 1.1% and the identification precision based on the fuzzy least squares-support vector machine is high.     

Dynamic characteristics of cold rolling mill and strip based on flatness and thickness control in rolling process简

The dynamic model of cold rolling mill based on strip flatness and thickness integrated control was proposed,containing the following sub-models：the rolling process model,the dynamic model of rolls along axial direction,and the compensation model.Based on the rule of volume flow rate,the dynamic rolling process model was built.The work roll and backup roll were taken as elastic continuous bodies,the effect of shear and moment of inertia were taken into consideration,and then the dynamic model of rolls was built.The two models were coupled together,and the dynamic model of rolling mill was built.In the dynamic model,the thermal expansion of the rolls,the wear of the rolls and other related parameters can not be considered.In order to compensate the dynamic model,the coupled static model of rolls and strip was applied.Then,according to the inner relationship of these models,the dynamic model and the compensation model were coupled,and the dynamic model of rolling mill based on the strip flatness and thickness integrated control was built.The dynamic simulation of the rolling process was made,and the dynamic thickness and the dynamic flatness information were obtained.This model not only provides a theory basis for the virtual rolling,but also provides a platform for the application of advanced control theory.