High impact poly(lactic acid)/poly(ethylene octene) blends prepared by reactive blending

Poly(ethylene octene) grafted with glycidyl methacrylate (POE‐g‐GMA) was prepared and used to toughen poly (lactic acid) (PLA) via reactive blending. It was found that the notched Izod impact strength of PLA/POE‐g‐GMA blends improved dramatically when the content of elastomer was higher than 10 wt%. Reactive compatibilization between PLA and POE‐g‐GMA were studied by Fourier transform infrared spectroscopy (FTIR) and “Molau test,” the results showed the end carboxyl groups of PLA reacted with the epoxide groups of POE‐g‐GMA during blending. This considerably improved the compatibilization, leading to better wetting of the dispersed phase by the PLA matrix and finer dispersed POE‐g‐GMA particles with narrow distribution. Moreover, the critical interparticle distance (L_c) of the dispersed domains for PLA/POE‐g‐GMA blends system at room temperature was also identified. POLYM. ENG. SCI., 2013. © 2012 Society of Plastics Engineers     

Polyoxymethylene/ethylene butylacrylate copolymer/ethylene‐methyl acrylate‐glycidyl methacrylate ternary blends

Blends of compatibilized polyoxymethylene (POM)/ethylene butylacrylate copolymer (EBA)/ethylene‐methyl acrylate‐glycidyl methacrylate copolymer (EMA‐GMA) and uncompatibilized POM/EBA were investigated. The notched impact strength of the compatibilized blends was higher than that of their uncompatibilized counterparts. The toughness of the POM blends was improved obviously with relatively low loading of EBA. Fourier transform infrared spectroscopy (FTIR) spectra of EMA‐GMA, pure POM, and POM/EBA/EMA‐GMA blends indicated that epoxy groups of EMA‐GMA reacted with terminal hydroxyl groups of POM molecular chains. The glass‐transition temperature (T_g) values of the POM matrix and the EBA phase were observed shifted to each other in the presence of EMA‐GMA compatibilizer indicating that the compatibilized blends had better compatibility than their uncompatibilized counterparts. With the addition of EBA to POM, both the compatibilized and uncompatibilized blends showed higher onset degradation temperature (T_d) than that of pure POM and the T_d values of the compatibilized blends were higher than those of their uncompatibilized counterparts. The scanning electron microscopy showed better EBA particles distribution state in the compatibilized system than in the uncompatibilized one. The compatibilized blend with an obvious rougher impact fracture surface indicated the ductile fracture mode. POLYM. ENG. SCI., 58:1127–1134, 2018. © 2017 Society of Plastics Engineers     

Influences of ethylene–butylacrylate–glycidyl methacrylate on morphology and mechanical properties of poly(butylene terephthalate)/polyolefin elastomer blends

Elastomer ethylene–butylacrylate–glycidyl methacrylate (PTW) containing epoxy groups were chosen as toughening modifier for poly(butylene terephthalate) (PBT)/polyolefin elastomer (POE) blend. The morphology, thermal, and mechanical properties of the PBT/POE/PTW blend were studied. The infrared spectra of the blends proved that small parts of epoxy groups of PTW reacted with carboxylic acid or hydroxyl groups in PBT during melt blending, resulting in a grafted structure which tended to increase the viscosity and interfere with the crystallization process of the blend. The morphology observed by scanning electron microscopy revealed the dispersed POE particles were well distributed and the interaction between POE and PBT increased in the PBT/POE/PTW blends. Mechanical properties showed the addition of PTW could lead to a remarkable increase about 10‐times in impact strength with a small reduction in tensile strength of PBT/POE blends. Differential scanning calorimetry results showed with increasing PTW, the crystallization temperature (T_c) and crystallinity (X_c) decreased while the melting point (T_m) slightly increased. Dynamic mechanical thermal analysis spectra indicated that the presence of PTW could improve the compatibility of PBT/POE blends. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40660.     

Improved compatibility of high‐density polyethylene/poly(ethylene terephthalate) blend by the use of blocked isocyanate group

The blocked isocyanate group (BHI) was synthesized to improve the storage stability of HI (2‐hydroxyethyl methacrylate combined with isophorone diisocyanate) and characterized by Fourier transform infrared spectroscopy (FTIR). High‐density polyethylene grafted with the blocked isocyanate group (HDPE‐g‐BHI) was used as a reactive compatibilizer for an immiscible high‐density polyethylene/poly(ethylene terephthalate) (HDPE/PET) blend. A possible reactive compatibilization mechanism is that regenerated isocyanate groups of HDPE functionalized by BHI react with the hydroxyl and carboxyl groups of PET during melt blending. The HDPE‐g‐BHI/PET blend showed the smaller size of a dispersed phase compared to the HDPE/PET blend, indicating improved compatibility between HDPE and PET. This increased compatibility was due to the formation of an in situ graft copolymer, which was confirmed by dynamic mechanical analysis. Differential scanning calorimetry (DSC) analysis represented that there were few changes in the crystallinity for the continuous PET phase of the HDPE‐g‐BHI/PET blends, compared with those of the HDPE/PET blends at the same composition. Tensile strengths and elongations at the break of the HDPE‐g‐BHI/PET blends were greater than those of the HDPE/PET blends. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 1017–1024, 2000     

Effect of the compatibilizer on the morphology and properties of dynamically cured PP/POE/epoxy blends

Dynamic vulcanization was successfully applied to epoxy resin reinforced polypropylene (PP)/ethylene‐octene copolymer (POE) blends, and the effects of different compatibilizers on the morphology and properties of dynamically cured PP/POE/epoxy blends were studied. The results show that dynamically cured PP/POE/epoxy blends compatibilized with maleic anhydride‐grafted polypropylene (MAH‐g‐PP) have a three‐phase structure consisting of POE and epoxy particles dispersed in the PP continuous phase, and these blends had improved tensile strength and flexural modulus. While using maleic anhydride‐grafted POE (MAH‐g‐POE) as a compatibilizer, the structure of the core‐shell complex phase and the PP continuous phase showed that epoxy particles could be embedded in MAH‐g‐POE in the blends, and gave rise to an increase in impact strength, while retaining a certain strength and modulus. DSC analysis showed that the epoxy particles in the blends compatibilized with MAH‐g‐PP were more efficient nucleating agents for PP than they were in the blends compatibilized with MAH‐g‐POE. WAXD analysis shows that compatibilization do not disturb the crystalline structure of PP in the blends. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Influence of a compatibilizer on the properties of polyethylene–octene elastomer/starch blends

The effect of a compatibilizer on the properties of corn starch‐reinforced metallocene polyethylene–octene elastomer (POE) blends was studied. The compatibility between POE and starch was improved markedly with an acrylic acid‐grafted POE (POE‐g‐AA) copolymer as a compatibilizer. Fourier transform infrared spectroscopy, X‐ray diffraction spectroscopy, differential scanning calorimetry, and scanning electron microscopy were used to examine the blends produced. The size of the starch phase increased with an increasing content of starch for noncompatibilized and compatibilized blends. The POE/starch blends compatibilized with the POE‐g‐AA copolymer lowered the size of the starch phase and had a fine dispersion and homogeneity of starch in the POE matrix. This better dispersion was due to the formation of branched and crosslinked macromolecules because the POE‐g‐AA copolymer had anhydride groups to react with the hydroxyls. This was reflected in the mechanical properties of the blends, especially the tensile strength at break. In a comparison with pure POE, the decrease in the tensile strength was slight for compatibilized blends containing up to 40 wt % starch. The POE‐g‐AA copolymer was an effective compatibilizer because only a small amount was required to improve the mechanical properties of POE/starch blends. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1792–1798, 2002     

Mechanical,thermal, and morphological characteristics of compatibilized and dynamically vulcanized polyoxymethylene/ethylene propylene diene terpolymer blends

Dynamically vulcanized blends of polyoxymethylene (POM) and ethylene propylene diene terpolymer (EPDM) with and without compatibilizer were prepared by melt mixing in a twin screw extruder. Maleic anhydride (MAH) grafted EPDM (EPDM‐g‐MAH) has been used as a compatibilizer. Dicumyl peroxide was used for vulcanizing the elastomer phase in the blends. Mechanical, dynamical mechanical, thermal, and morphological properties of the blend systems have been investigated as a function of blend composition and compatibilizer content. The impact strength of both dynamically vulcanized blends and compatibilized/dynamically vulcanized blends increases with increase in elastomer content with decrease in tensile strength. Dynamic mechanical analysis shows decrease in tanδ values as the elastomer and compatibilizer content increased. Thermograms obtained from differential scanning calorimetric studies reveal that compatibilized blends have lower T_m values compared to dynamically vulcanized blends, which confirms strong interaction between the plastic and elastomer phase. Scanning electron microscopic observations on impact fractured surface indicate reduction in particle size of elastomer phase and its high level of dispersion in the POM matrix. In the case of compatibilized blends high degree of interaction between the component polymers has been observed. POLYM. ENG. SCI., 47:934–942, 2007. © 2007 Society of Plastics Engineers     

Polylactide toughening with epoxy‐functionalized grafted acrylonitrile–butadiene–styrene particles

Glycidyl methacrylate functionalized acrylonitrile–butadiene–styrene (ABS‐g‐GMA) particles were prepared and used to toughen polylactide (PLA). The characteristic absorption at 1728 cm^?1 of the Fourier transform infrared spectra indicated that glycidyl methacrylate (GMA) was grafted onto the polybutadiene phase of acrylonitrile–butadiene–styrene (ABS). Chemical reactions analysis indicated that compatibilization and crosslinking reactions took place simultaneously between the epoxy groups of ABS‐g‐GMA and the end carboxyl or hydroxyl groups of PLA and that the increase of GMA content improved the reaction degree. Scanning electron microscopy results showed that 1 wt % GMA was sufficient to satisfy the compatibilization and that ABS‐g‐GMA particles with 1 wt % GMA dispersed in PLA uniformly. A further increase of GMA content induced the agglomeration of ABS‐g‐GMA particles because of crosslinking reactions. Dynamic mechanical analysis testing showed that the miscibility between PLA and ABS improved with the introduction of GMA onto ABS particles because of compatibilization reactions. The storage modulus decreased for the PLA blends with increasing GMA content. The decrease in the storage modulus was due to the chemical reactions in the PLA/ABS‐g‐GMA blends, which improved the viscosity and decreased the crystallization of PLA. A notched impact strength of 540 J/m was achieved for the PLA/ABS‐g‐GMA blend with 1 wt % GMA, which was 27 times than the impact strength of pure PLA, and a further increase in the GMA content in the ABS‐g‐GMA particles was not beneficial to the toughness improvement. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Morphology and properties of nylon 6 and high density polyethylene blends in presence of nanoclay and PE‐g‐MA

In this study, we report the synergistic effect of nanoclay and maleic anhydride grafted polyethylene (PE‐g‐MA) on the morphology and properties of (80/20 w/w) nylon 6/high density polyethylene (HDPE) blend. Polymer blend nanocomposites containing nanoclay with and without compatibilizer (PE‐g‐MA) were prepared by melt mixing, and their morphologies and structures were examined with scanning electron microscopy (SEM) and wide angle X‐ray diffractometer (WAXD) study. The size of phase‐separated domains decreased considerably with increasing content of nanoclay and PE‐g‐MA. WAXD study and transmission electron microscopy (TEM) revealed the presence of exfoliated clay platelets in nylon 6 matrix, as well as, at the interface of the (80/20 w/w) nylon 6/HDPE blend–clay nanocomposites. Addition of PE‐g‐MA in the blend–clay nanocomposites enhanced the exfoliation of clays in nylon 6 matrix and especially at the interface. Thus, exfoliated clay platelets in nylon 6 matrix effectively restricted the coalescence of dispersed HDPE domains while PE‐g‐MA improved the adhesion between the phases at the interface. The use of compatibilizer and nanoclay in polymer blends may lead to a high performance material which combines the advantages of compatibilized polymer blends and the merits of polymer nanocomposites. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Influence of the degree of grafting on the morphology and mechanical properties of blends of poly(butylene terephthalate) and glycidyl methacrylate grafted poly(ethylene‐co‐propylene) (EPR)

Poly(ethylene‐co‐propylene) (EPR) was functionalized to varying degrees with glycidyl methacrylate (GMA) by melt grafting processes. The EPR‐graft‐GMA elastomers were used to toughen poly(butylene terephthalate) (PBT). Results showed that the grafting degree strongly influenced the morphology and mechanical properties of PBT/EPR‐graft‐GMA blends. Compatibilization reactions between the carboxyl and/or hydroxyl of PBT and epoxy groups of EPR‐graft‐GMA induced smaller dispersed phase sizes and uniform dispersed phase distributions. However, higher degrees of grafting (>1.3) and dispersed phase contents (>10 wt%) led to higher viscosities and severe crosslinking reactions in PBT/EPR‐graft‐GMA blends, resulting in larger dispersed domains of PBT blends. Consistent with the change in morphology, the impact strength of the PBT blends increased with the increase in EPR‐graft‐GMA degrees of grafting for the same dispersion phase content when the degree of grafting was below 1.8. However, PBT/EPR‐graft‐GMA1.8 displayed much lower impact strength in the ductile region than a comparable PBT/EPR‐graft‐GMA1.3 blend (1.3 indicates degree of grafting). Morphology and mechanical results showed that EPR‐graft‐GMA 1.3 was more suitable in improving the toughness of PBT. SEM results showed that the shear yielding properties of the PBT matrix and cavitation of rubber particles were major toughening mechanisms. Copyright © 2006 Society of Chemical Industry     

Influence of Compatibilizer on Morphology and Dynamic Rheological Behavior of Polyethylene-Octene Elastomer/Starch Blends

The morphology and rheology of polyethylene-octene elastomer (POE)/crosslinked starch (CS) immiscible blends with various amounts of compatibilizer were experimentally examined. A graft copolymer, POE-g-MAH, acting as the compatibilizer, was used to modify the interface of the blend. The particle radius in the POE/CS 80/20 system decreased with increasing compatibilizer up to 5 wt%, beyond which the particle size slightly increased. This indicates that the interface reaches saturation when the compatibilizer content is 5 wt%, leading to reduced effectiveness of the compatibilizer. From the SEM micrographs, the compatibilized blends were found to have better interfacial adhesion between the POE and starch phase than the uncompatibilized blends. Rheological examination shows a sharp reduction of the viscoelastic modulus and complex viscosity in blends containing 10 wt% compatibilizer. When the content of compatibilizer is less than 5 wt%, the viscoelastic modulus and complex viscosity of the blends increase with increasing the content of compatibilizer.     

Study on toughening effect of maleic anhydride‐grafted‐poly(ethylene‐octene) to EVOH and their compatibility

Blends of poly(ethylene‐co‐vinyl alcohol) (EVOH) with maleic anhydride‐grafted‐poly(ethylene‐octene) (POE‐g‐MAH) were prepared by blending extrusion in order to improve the toughness and flexibility of EVOH. The compatibility behavior of these blends with POE‐g‐MAH content range from 0 to 25 wt% was studied using mechanical, thermal, infrared, and morphology characterization techniques. The mechanical test results showed that POE‐g‐MAH can significantly improve the impact toughness of EVOH with a brittle‐tough transition appeared at the POE‐g‐MAH content of 20 wt%. A huge increase of toughness of the blend was also observed when the POE‐g‐MAH content was increased to 15 wt%. The thermal analysis of the blends demonstrated that the thermal stability of EVOH is improved with the addition of POE‐g‐MAH, adding 20 wt% or more POE‐g‐MAH can effectively decrease the crystallinity of EVOH and greatly improve compatibility between the two components. The existence of esterification between anhydride groups in POE‐g‐MAH and hydroxyl groups in EVOH in melt processing was confirmed using Fourier transform infrared technique. Morphology analysis of the Izod impact fractures has clearly shown the mechanisms for these blends to change from brittle to tough with increasing the POE‐g‐MAH content. POLYM. ENG. SCI., 53:2093–2101, 2013. © 2013 Society of Plastics Engineers     

Study on the microstructures and mechanical behaviour of compatibilized polypropylene/polyamide‐6 blends

A series of blends of polypropylene (PP)–polyamide‐6 (PA6) with either reactive polyethylene–octene elastomer (POE) grafted with maleic anhydride (POE‐g‐MA) or with maleated PP (PP‐g‐MA) as compatibilizers were prepared. The microstructures and mechanical properties of the blends were investigated by means of tensile and impact testing and by scanning electron microscopy and transmission electron microscopy. The results indicated that the miscibility of PP–PA6 blends was improved with the addition of POE‐g‐MA and PP‐g‐MA. For the PP/PA6/POE‐g‐MA system, an elastic interfacial POE layer was formed around PA6 particles and the dispersed POE phases were also observed in the PP matrix. Its Izod impact strength was four times that of pure PP matrix, whilst the tensile strength and Young's modulus were almost unchanged. The greatest tensile strength was obtained for PP/PA6/PP‐g‐MA blend, but its Izod impact strength was reduced in comparison with the pure PP matrix. © 2002 Society of Chemical Industry     

Study on the properties of polyethylene–octene elastomer/wood flour blends

In the present study, the properties of metallocene polyethylene–octene elastomer (POE) and wood flour (WF) blends were examined by Fourier transform infrared (FTIR) spectroscopy, differential scanning calorimetry (DSC), an Instron mechanical tester, and scanning electron microscopy (SEM). The results showed that the mechanical properties of POE were obviously lowered, due to the poor compatibility between the two phases, when it was blended with WFs. A fine dispersion and homogeneity of WF in the polymer matrix could be obtained when acrylic acid‐grafted POE (POE‐g‐AA) was used to replace POE for manufacture of the blends. This better dispersion is due to the formation of branched and crosslinked macromolecules since the POE‐g‐AA copolymer had carboxyl groups to react with the hydroxyls. This is reflected in the mechanical and thermal properties of the blends. In comparison with a pure POE/WF blend, the increase in tensile strength at break was remarkable for the POE‐g‐AA/WF blend. The POE‐g‐AA/WF blends are more easily processed than are the POE/WF blends, since the former had a lower melt viscosity than that of the latter. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1919–1924, 2003     

Effect of PE-g-MA-Compatibilizer on the Morphology and Mechanical Properties of 70/30 HDPE/ENR Blends

The effects of PE-g-MA as a compatibilizer in binary blends of 70/30 high-density polyethylene/epoxidized natural rubber (HDPE/ENR) have been investigated by means of mechanical analysis and scanning electron microscopy. The special emphasis was given to the role of PE-g-MA in inducing interactions between HDPE and ENR. It has been observed that increasing the amount of PE-g-MA in the blend increases the tensile strength, elongation at break, and impact strength. It is believed that the degree of cross-link increased, which led to improve the interaction between the HDPE and ENR. The optimum stress values are shown in the blend containing 6% PE-g-MA. Scanning electron micrographs (SEM) of the samples also indicated that the addition of compatibilizer decreases the domain size of the dispersed phase. Well-dispersed plastic particles in a rubber matrix were strongly indicated in these samples. The results obtained reveal that the addition of PE-g-MA in HDPE/ENR blend led to an increase in the homogeneity of the blends.     

Rheology‐morphology correlation in PET/PP blends: Influence of type of compatibilizer

Rheological and morphological properties of melt processed poly(ethylene terephthalate) (PET)/polypropylene (PP) blends are presented. Two types of compatibilizer namely, PP‐g‐MA <MA= maleic anhydtide> and Elvaloy PTW, an n‐butyl acrylate glycidyl methacrylate ethylene terpolymers, were incorporated at different levels to the PET/PP blend system. Scanning electron microscopy revealed that the dispersed particle sizes were smaller in PET‐rich blends than PP‐rich blends. With increasing compatibilizer level, the refinement of morphology was observed in both the systems. However, the blends compatibilized with PTW showed a more refined (smaller) particle size, and at high PTW content (10 wt%), the morphology changed towards monophasic. The significant changes in morphology were attributed to the highly reactive nature of PTW. Investigation of rheological properties revealed that the viscosity of the PET/PP blends followed typical trends based on mixing rule, which calculates the properties of blends based on a linear average. Incorporation of PP‐g‐MA into the blends resulted in a negative deviation in the viscosity of the system with respect to that of the neat blend. With increasing PP‐g‐MA level, the deviation became more pronounced. Although incorporation of the compatibilizer into the PET/PP blends refined the morphology, it led to a drastic drop of viscosity, which could be attributed to inherently lower molecular weight of the compatibilizer. In the case of the blends compatibilized by PTW, a strong positive deviation in rheological properties was observed that confirmed the stronger interaction between the blend components due to reactive compatibilization process, which led to the more refined morphology in this series of blends. J. VINYL ADDIT. TECHNOL., 19:25–30, 2013. © 2013 Society of Plastics Engineers     

Preparation of polyethylene‐octene elastomer/clay nanocomposite and microcellular foam processed in supercritical carbon dioxide

Polyethylene‐octene elastomer (POE)/organoclay nanocomposite was prepared by melt mixing of the POE with an organoclay (Cloisite 20A) in an internal mixer, using poly[ethylene‐co‐(methyl acrylate)‐co‐(glycidyl methacrylate)] copolymer (E‐MG‐GMA) as a compatibilizer. X‐ray diffraction and transmission electron microscopy analysis revealed that an intercalated nanocomposite was formed and the silicate layers of the clay were uniformly dispersed at a nanometre scale in the POE matrix. The nanocomposite exhibited greatly enhanced tensile and dynamic mechanical properties compared with the POE/clay composite without the compatibilizer. The POE/E‐MA‐GMA/clay nanocomposite was used to produce foams by a batch process in an autoclave, with supercritical carbon dioxide as a foaming agent. The nanocomposite produced a microcellular foam with average cell size as small as 3.4 µm and cell density as high as 2 × 10¹¹ cells cm^?3. Copyright © 2005 Society of Chemical Industry     

Polymer blends of PBT and PP compatibilized by ethylene-co-glycidyl methacrylate copolymers

The ethylene-co-glycidyl methacrylate (EG) copolymer is an efficient reactive compatibilizer for polymer blends of poly(butylene terephthalate) (PBT) and polypropylene (PP). During melt processing, the epoxy functional group of the EG copolymer can react with the PBT carboxylic acid and/or hydroxyl terminal groups at the interface to form various EG-g-PBT copolymers. These in situ formed grafted copolymers tend to concentrate along the interface to reduce the interfacial tension at the melt and result in finer phase domains. Higher glycidyl methacrylate (GMA) content in the EG copolymer or a higher quantity of the EG compatibilizer in the blend results in a better compatibilized blend in terms of finer phase domains, higher viscosity, and better mechanical properties. The presence of only 50 ppm catalyst (ethyltriphenyl phosphonium bromide) in the EG compatibilized blend further improves the blend compatibility substantially. © 1996 John Wiley & Sons, Inc.     

Blends of epoxy resins and polyphenylene oxide as processing aids and toughening agents 2: Curing kinetics,rheology, structure and properties

The curing behaviour, chemorheology, morphology and dynamic mechanical properties of epoxy ? polyphenylene oxide (PPO) blends were investigated over a wide range of compositions. Two bisphenol A based di‐epoxides ? pure and oligomeric DGEBA ? were used and their cure with primary, tertiary and quaternary amines was studied. 4,4′‐methylenebis(3‐chloro‐2,6‐diethylaniline) (MCDEA) showed high levels of cure and gave the highest exotherm peak temperature, and so was chosen for blending studies. Similarly pure DGEBA was selected for blending due to its slower reaction rate because of the absence of accelerating hydroxyl groups. For the PPO:DGEBA340/MCDEA system, the reaction rate was reduced with increasing PPO content due to a dilution effect but the heat of reaction were not significantly affected. The rheological behaviour during cure indicated that phase separation occurred prior to gelation, followed by vitrification. The times for phase separation, gelation and vitrification increased with higher PPO levels due to a reduction in the rate of polymerization. Dynamic mechanical thermal analysis of PPO:DGEBA340/MCDEA clearly showed two glass transitions due to the presence of phase separated regions where the lower T_g corresponded to an epoxy‐rich phase and the higher T_g represented the PPO‐rich phase. SEM observations of the cured PPO:DGEBA340/MCDEA blends revealed PPO particles in an epoxy matrix for blends with 10 wt% PPO, co‐continuous morphology for the blend with 30 wt% PPO and epoxy‐rich particles dispersed in a PPO‐rich matrix for 40wt% and more PPO. © 2014 Society of Chemical Industry     

An investigation on recycled PET/PP and recycled PET/PP‐EP compatibilized blends: Rheological,morphological, and mechanical properties

The effectiveness of P(E‐co‐MA‐co‐GMA) as a compatibilizer for recycled PET/PP and recycled PET/PP‐EP (polypropylene (ethylene‐propylene) heterophase copolymer) blends was investigated by means of morphological (scanning electron microscopy), rheological (small amplitude oscillatory shear), mechanical (tensile, flexural and impact tests), and thermal (differential scanning calorimetry) properties. Compatibilizer concentration ranged from 1 to 5 wt % with respect to the whole blend. All blends were obtained in a 90/10 composition using a twin screw extruder. Compatibilization effects for PETr/PP‐EP were more pronounced due to ethylene segments present in both PP‐EP and P(E‐co‐EA‐co‐GMA). PETr/PP‐EP has shown greater dispersed phase size reduction, a more solid‐like complex viscosity behavior and larger storage modulus at low frequencies in relation to PETr/PP blend. For both investigated blends, mechanical properties indicated an improvement in both elongation at break and impact strength with increasing compatibilizer content. PETr/PP‐EP blends showed improved performance for the same level of compatibilizer content. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41892.