Effect of friction welding condition on joining phenomena and joint strength of friction welded joint between brass and low carbon steel

Abstract

This paper describes the effect of friction welding condition on joining phenomena and joint strength of friction welded joints between copper–zinc alloy (brass) and low carbon steel (LCS). When the joint was made at a friction pressure of 30 MPa with a friction speed of 27·5 s^?1, brass transferred to the half radius region of the weld interface on the LCS side. Then, transferred brass extended towards the almost whole weld interface with increasing friction time. The joint efficiency increased with increasing friction time, and then the joint obtained 100% and the brass base metal fracture when the joint was made with a friction time of 4·2 s or longer. However, the fact that all joints had some cracks at the periphery portion of the weld interface was due to a deficiency of transferred brass at the periphery portion on the weld interface of the LCS side. On the other hand, brass transferred to the peripheral region of the weld interface on the LCS side, and then transferred towards the entire weld interface when the joint was made at a friction pressure of 90 MPa with a friction speed of 27·5 s^?1. The joint efficiency increased with increasing friction time, and it reached 100% at a friction time of 1·5 s or longer. In addition, all joints fractured from the brass base metal with no cracking at the weld interface. To obtain 100% joint efficiency and the brass base metal fracture with no cracking at the weld interface, the joint should be made with opportune high friction pressure and friction time at which the entire weld interface had the transferred brass.     

Joining phenomena and joint strength of friction welded joint between aluminium–magnesium alloy (AA5052) and low carbon steel

Abstract

The joining phenomena and the joint strength of an Al–Mg alloy (AA5052) and low carbon steel (LCS) friction welded joints were investigated. The weld interface of the LCS side at a friction time of 1·2 s had a slightly transferred AA5052, and then the entire weld interface had it at a friction time of 3·0 s or longer. The joint efficiency increased with increasing friction time, but it decreased at a friction time of 12·0 s or longer. The joint at a friction time of 3·0 s with forge pressure of 190 MPa had 100% joint efficiency and the AA5052 base metal fracture with no crack at the weld interface. The weld interface of these joints also had no intermetallic compound. On the other hand, the joint at a friction time of 8·0 s, which had ～97% joint efficiency, fractured between the AA5052 side and the weld interface because it had the intermetallic compound at the weld interface.     

Effect of friction welding conditions on mechanical properties of A5052 aluminium alloy friction welded joint

Abstract

The present paper describes the mechanical properties of Al–Mg aluminium alloy (A5052) friction welded joints. Two types of A5052 with different tensile properties were used, namely, H112 base metal with 188 MPa tensile strength and H34 with 259 MPa tensile strength. Similar metal specimens were joined using a continuous drive friction welding machine with an electromagnetic clutch to prevent braking deformation. That is, the joints were welded using the 'low heat input' friction welding method developed by the present authors, in which the heat input is lower than in the conventional method. An A5052–H112 joint produced using a friction speed of 27·5 s^?1, friction pressure of 30 MPa, friction time of 2·0 s (just after the initial peak torque), and forge pressure of 60 MPa had approximately 95% joint efficiency. It fractured at the welded interface and in the A5052–H112 base metal. To improve the joint efficiency, an A5052–H112 joint was produced at a forge pressure of 75 MPa, which was the same as the yield strength of the A5052–H112 base metal. It had 100% joint efficiency and fractured in the A5052–H112 base metal. In contrast, an A5052–H34 joint was made using a friction speed of 27·5 s^?1, friction pressure of 90 MPa, friction time of 0·3 s (just after the initial peak torque), and forge pressure of 180 MPa. It had approximately 93% joint efficiency and fractured in the A5052–H34 base metal. This joint also had a softened region at the welded interface and in the adjacent region. To improve the joint efficiency, an A5052–H34 joint was made at a forge pressure of 260 MPa, which was the same as the ultimate tensile strength of the A5052–H34 base metal. Although this joint had a slightly softened region at its periphery, it had approximately 93% joint efficiency. The failure of the A5052–H34 joint to achieve 100% joint efficiency is due to a slight softening at the periphery and the difference in the anisotropic properties of the A5052–H34 base metal between the longitudinal and radial directions.     

Effect of post-weld heat treatment on joint properties of friction welded joint between brass and low carbon steel

Abstract

This paper describes the effect of post-weld heat treatment (PWHT) on joint properties of copper–zinc alloy (brass) and low carbon steel friction welded joints. The as-welded joint obtained 100% joint efficiency and the brass base metal fracture without cracking at the weld interface, and had no intermetallic compound layer. The joint efficiency with PWHT decreased with increasing heating temperature and its holding time, and its scatter increased with those increasing parameters. When the joint was heat treated at 823 K for 360 ks, it did not achieve 100% joint efficiency and fractured between the weld interface and the brass base metal although it had no intermetallic compound. The cracking at the peripheral portion of the weld interface was generated through PWHT. The cracking was due to the dezincification and the embrittlement of the brass side during PWHT.     

Effect of inclination of weld faying surface on joint strength of friction welded joint and its allowable limit for austenitic stainless steel solid bar similar diameter combination

This paper describes the effect of the inclination of the weld faying surface on joint strength of friction welded joint and its allowable limit for austenitic stainless steel (SUS304) solid bar similar diameter combination. In this case, the specimen was prepared with the inclination of the weld faying surface pursuant to the JIS Z 3607, and the joint was made with that diameter of 12 mm, a friction speed of 27.5 s^?1, and a friction pressure of 30 MPa. The initial peak torque decreased with increasing inclination of the weld faying surface, and then the elapsed time for the initial peak increased with increasing that inclination. However, the steady torque was kept constant in spite of the inclination of the weld faying surface increasing. The joints without the inclination of the weld faying surface, which were made with friction times of 1.5 and 2.0 s with a forge pressure of 270 MPa, had achieved 100% joint efficiency with the base metal fracture. Those joints had 90° bend ductility with no crack at the weld interface. The joints with the inclination of the weld faying surface of 0.3 mm (gap length of 0.6 mm), which were allowable distance, was also obtained the same result with this condition. Furthermore, those joints with a friction time of 2.5 s obtained the same result. On the other hand, the joints with the inclination of the weld faying surface of 0.6 mm (gap length of 1.2 mm), which were twice inclination of the allowable distance, also obtained the same result in a friction time of 2.5 s. However, the joints without the inclination of the weld faying surface at this friction time did not obtain the base metal fracture, although those achieved 100% joint efficiency. In conclusion, to obtain 100% joint efficiency and the base metal fracture with no cracking at the weld interface, the joint must be made with the inclination of the weld faying surface, with allowable distance pursuant to the JIS Z 3607.     

Mechanical properties of friction welded joint between Ti–6Al–4V alloy and Al–Mg alloy (AA5052)

Abstract

The present paper describes the mechanical properties of a friction welded joint between Ti–6Al–4V alloy and Al–Mg alloy (AA5052). The Ti–6Al–4V/AA5052–H112 joint, made at a friction speed of 27.5 rev s^?1, friction pressure of 30 MPa, friction time of 3.0 s, and forge pressure of 60 MPa, had 100% joint efficiency and fractured in the AA5052–H112 base metal. The Ti–6Al–4V/AA5052–H34 joint, made under the same friction welding conditions, did not achieve 100% joint efficiency and it fractured in the AA5052–H34 base metal because the AA5052–H34 base metal had softened under friction heating. The joints made at low friction speed or using short friction time showed fracture at the welded interface because a sufficient quantity of heat for welding could not be produced. However, the joints made at high friction speed or using long friction time were also fractured at the welded interface: in this instance, the welded interface also had an intermetallic compound layer consisting of Ti₂Mg₃Al₁₈. The Ti–6Al–4V/AA5052–H34 joint made at a friction speed of 27.5 rev s^?1 with friction pressure of 150 MPa, friction time of 0.5 s, and forge pressure of 275 MPa had 100% joint efficiency and fractured in the AA5052–H34 base metal, although the AA5052–H34 side softened slightly. In conclusion, the Ti–6Al–4V/AA5052–H112 joint and Ti–6Al–4V/AA5052–H34 joint had 100% joint efficiency and fractured in the AA5052 base metal when made under the friction welding conditions described above.     

Properties and improvement of super fine grained steel friction welded joint

Abstract

This paper describes friction welded joint properties of super fine grained steel (SFGS) and discusses improvements in these joint properties. The average grain size diameter of the SFGS base metal is ～0·6 μm, and its ultimate tensile strength is 660 MPa. The joint, made by a continuous drive friction welding machine (conventional method), fractured at the welded interface even though it possessed 100% joint efficiency. This was due to both the coarsening of the grain size and the softening of the welded interface with its adjacent region caused by heat input during braking times. The authors developed a joining method using a continuous drive friction welding machine that has an electromagnetic clutch to eliminate heat input during braking time, which was called the 'low heat input friction welding method' (LHI method). The joint obtained by the LHI method had the same tensile strength as the base metal at the friction time when the friction torque reached the initial peak. That is, the joint obtained 100% joint efficiency and fractured at the base metal, although the adjacent region of the welded interface softened only slightly. The grain size of this joint was smaller than that obtained by the conventional method. It was clarified that the optimum friction welded joint of the SFGS could be obtained by the LHI method in comparison with the conventional method.     

Selection guide of insert piece shape for steel joint by autocompleting friction welding method

Abstract

An autocompleting friction welding method, which was developed by the authors, is to weld with using a rotating insert piece set between fixed base metals. This paper describes the selection guide of the insert piece size for steel joints by the autocompleting friction welding method. The base metal was low carbon steel (LCS), and the weld faying surface of the fixed specimen had a 10 mm diameter. The effect of the thickness at the bottom of the grooves for the insert piece (groove bottom thickness) on the joining phenomena was investigated. When the joint was made at a friction pressure of 90 MPa with a friction speed of 27·5 s^?1, the insert piece had a shear fracture towards the circumferential direction (circumferential shear fracture) in the peripheral portion of the weld interfaces by the initial peak produced during the friction process. In this case, the insert piece had the following dimensions: the thickness was 4·0 mm, and the groove bottom thickness was 1·2 mm or over with an inner groove diameter of 11 mm. In particular, the joint with a groove bottom thickness of 1·2 mm had 100% joint efficiency and the LCS base metal fracture with no crack at the weld interface. The value of a circumferential shear fracture (CSF value) was defined and calculated by the ratio between the theoretical and the actual generated friction torques. When the CSF value nearly equalled 1, the joint had 100% joint efficiency and the LCS base metal fracture with no crack at the weld interface.     

Analysis of acoustic and optical signals used as a basis for controlling laser‐welding processes

Stud joints of 2017 aluminium alloy were friction welded and its joint strength was examined. A stair zone was formed at the weld interface. Although the hardness of the stair zone was almost the same as base metals, the heat-affected zone of the bar and the plate was softened. The tensile strength of joints tended to increase with a pressure and a friction time, and the highest tensile strength was 275 MPa (63.1% joint efficiency for the bar base metal). In the bending testing, joints were cracked in the weld zone at a bending angle of less than 5°. In the fatigue testing, joints fractured near the weld interface and the fatigue strength of joints increased as the tensile strength of joints was high.     

Joint properties and its improvement of high-tensile strength steel joint by autocompleting friction welding method

This paper describes the improvement of properties of a high-tensile strength steel joint by an autocompleting friction welding method that was developed by the authors. The base metal was high-tensile strength steel of 800 MPa class. The weld faying surface of the fixed specimen had a 10 mm diameter, and the effect of the thickness and that at the bottom of the grooves (groove bottom thickness) for the insert piece on the joining phenomena and joint properties were investigated. The value of a circumferential shear fracture (CSF value) was defined and calculated by the ratio between the theoretical and the actual generated friction torques. When the CSF value was lower than 1, the insert piece had the CSF before the friction torque reached the initial peak. Also, when the CSF value was larger than 1, the insert piece had the CSF after the friction torque reached the initial peak. When the joint was made at the insert thickness of 5 mm with the CSF value of nearly 1, it had 100% joint efficiency although it had the softened region near the weld interfaces. The joint had cracks at the weld interface when it was made with friction pressures of 36 and 120 MPa. However, the joint had no crack at the weld interface when it was made with a friction pressure of 90 MPa. When the joint was made at the insert thickness of 4 mm with the CSF value of nearly 1, it had also 100% joint efficiency although it had the softened region near the weld interfaces. However, the softened region at the weld interface of the joint with the insert thickness of 4 mm was lower than that with 5 mm. Also, this joint had 90° bend ductility with no crack at the weld interface. In conclusion, it was possible to make a joint with no cracks for high-tensile strength steel by an autocompleting friction welding method.     

Strength enhancement of autocompleting medium and high carbon steels friction welded joints

An autocompleting friction welding method, which was developed by the authors, is to weld with using a rotating insert piece set between fixed workpieces. The conditions to enhance the strength of the welded joint in an autocompleting friction welding method which involves a rotating insert between the fixed workpieces were determined. The weld faying surface of the fixed specimen had a 10 mm diameter. When MCS joint was made at an insert thickness of 4 mm through a friction pressure of 36 MPa, it did not achieve 100% joint efficiency because the weld interfaces were not completely joined. MCS joint had 100% joint efficiency and fractured on the MCS base metal although the crack was generated at the weld interface, when that was made at an inner groove diameter of 11 mm with the bottom of the grooves for the insert piece (groove bottom thickness) of 0.9 mm or more through a friction pressure of 90 MPa. To obtain a joint with no cracks, MCS joint was made with an inner groove diameter of 12 mm at a friction pressure of 90 MPa. When the groove bottom thickness was 0.75 mm, MCS joint had 100% joint efficiency and the MCS base metal fracture with no crack at the weld interface. When HCS joint was made with an inner groove diameter of 11 mm at friction pressures of 90 and 150 MPa, it did not achieve 100% joint efficiency because the weld interfaces were not joined completely. The weld interfaces of HCS joint at a friction pressure of 120 MPa were completely joined although it did not achieve 100% joint efficiency. To improve the joint efficiency, HCS joint was made with an insert thickness of 5 mm, a groove bottom thickness of 0.64 mm, and an inner groove diameter of 12 mm with a friction pressure of 120 MPa. HCS joint had 100% joint efficiency and fractured on the HCS base metal with no crack at the weld interface.     

铝和不锈钢摩擦焊接界面组织与性能研究

针对6061铝合金与1Cr18Ni9Ti不锈钢异种金属焊接,采用连续旋转摩擦焊接实现铝钢异种材料焊接,并采用SEM、EDS进行组织分析和性能测试.试验结果表明:在旋转速率为600 r/min、顶锻压力为4.5 MPa,顶锻时间为2 s等工艺参数条件下,铝/钢摩擦焊接头结合紧密,界面呈现波纹状;接头抗拉强度可达252 M...     

Explosively welded copper‐stainless steel bimetal and an example of its application

Summary

Friction welding was carried out under various welding conditions using high strength 7075 aluminium alloy; an investigation into the structure and the mechanical properties of joints thus obtained leads to the following conclusions: The fibrous structure at the heat affected zone changed to align in the direction of flash expulsion and the fibrous structure at the weld zone disappeared and a non-directional fine grain structure was evident. The hardness at the weld interface had a lower value than that of the base metal and an even more softened zone than the weld interface was noted at the heat affected zone. The hardness values at the weld interface and the softened zone were seen to recover after friction welding due to natural ageing but did not recover fully. Both the values of the tensile strength and the elongation declined compared with the base metal in joints made under the conditions that gave the maximum value of tensile strength; the former was 81% and the latter was 83% that of the base metal. The joint impact value of a specimen with a notch on the weld interface was 73% that of the base metal.     

Development of autocompleting friction welding method

Abstract

This paper describes an autocompleting friction welding method that was carried out to weld with an insert piece set between fixed base metals. The base metal was low carbon steel, and the faying surface of the fixed specimen had a 10 mm diameter. The effect of the thickness of the insert piece (insert thickness) on the joining phenomena was investigated. When the insert thickness was 3˙2 mm and the friction welding conditions were a friction speed of 27˙5 s^–1 and friction pressure of 36 MPa, the insert piece had a shear fracture toward the circumferential direction in the peripheral portion of the weld interfaces by the initial peak produced during the friction process. The joint also had cracks at the adjacent region of the weld interfaces, although it had the same tensile strength as the base metal. On the other hand, the joint made using the insert piece with a groove on its peripheral portion had the same tensile strength as the base metal, where it fractured. This joint also had 90° bend ductility without cracks. In this case, the optimum insert thickness was 4˙0 mm, and the thickness at the bottom of the grooves (groove bottom thickness) was 1˙2 mm with an 11 mm inner groove diameter, and the friction welding conditions were a friction speed of 27˙5 s^–1 and friction pressure of 36 MPa. In conclusion, a sound friction welded joint was made by an autocompleting friction welding method.     

5052铝合金FSW接头组织和力学性能

采用搅拌摩擦焊焊接8 mm厚5052-O铝合金,并对焊接接头进行了显微组织观察和力学性能测试。结果表明:接头组织左右不对称,前进侧与母材分界线较明显,后退侧与母材分界线较模糊;焊接接头抗拉强度平均值为193.5 MPa,接头强度可达母材的99%,伸长率可达母材的84%;焊接接头正弯角和背弯角均可达到180°,弯曲性能良好;焊核区显微硬度约为72 HV,略高于母材,硬度最低点出现在前进侧熔合过渡区。     

Analysis of process parameters effects on dissimilar friction stir welding of AA1100 and A441 AISI steel

Abstract

A prominent benefit of friction stir welding process is to join plates with dissimilar material. In this study, an attempt is made to find effects of tool offset, plunge depth, welding traverse speed and tool rotational speed on tensile strength, microhardness and material flow in dissimilar friction stir welding of AA1100 aluminium alloy and A441 AISI steel plates. Here, one factor at a time experimental design was utilised for conducting the experiments. Results indicated the strongest joint obtained at 1·3?mm tool offset and 0·2?mm plunge depth when the tool rotational speed and linear speed were 800?rev min^??1 and 63?mm min^??1 respectively. The maximum tensile strength of welded joints with mentioned optimal parameters was 90% aluminium base metal. Fracture locations in tensile test at all samples were in aluminium sides. Owing to the formation of intermetallic compounds at high tool rotational speed, the microhardness of joint interface goes beyond that of A441 AISI steel.     

铝合金/合金钢异种金属摩擦焊接头组织与性能

针对油气资源勘探开发用钻杆轻量化的需求,以小尺寸试棒7075-T6铝合金和37CrMnMo合金钢利用连续驱动摩擦焊技术实现连接,探索开发铝合金/合金钢轻量化复合钻杆焊接制造的可能性和可行性,研究了焊接工艺参数对接头成形、微观组织及力学性能的影响.结果表明,接头界面铝侧的晶粒受到力和热的作用发生完全动态再结晶,而在热力影...     

Properties of as welded and heat treated pure titanium–7075 Al–Zn–Mg alloy friction weld joints

Abstract

The effects of joining conditions and an age hardening post­weld heat treatment (PWHT) at 120°C for 24 h on the tensile strength and metallurgical properties of dissimilar friction joints between pure titanium and age strengthened 7075 Al–Zn–Mg alloy were investigated. Highest strength was achieved using intermediate friction pressure (150 MPa), short friction time (0.5 s), and high upsetting (forging) pressure (400 MPa). The joint tensile strength decreased when the joint diameter was increased from 8 to 16 mm. The joint tensile strength of as welded (AW) dissimilar joints was similar to that of PWHT joints with diameters of 8, 12, and 16 mm. Detailed TEM confirmed that there was a negligible difference in the thickness of the intermetallic layer formed at the dissimilar joint interface for AW and PWHT joints. While the intermetallic phases formed at the joint interface comprised Al₃Ti, τ (Ti₂Mg₃Al₁₈), and Al in AW joints, they consisted of Al+τ or Mg₂Al₃+τ+Al in PWHT joints. Softened regions were generated in 7075 base material immediately next to the interface in AW joints. Post­weld heat treatment increased the hardness of the softened region almost to that of as received 7075–T6 base material in 12 and 16 mm diameter joints. In contrast, the hardness of the softened region in 8 mm diameter joints could not be recovered to that of the as received material. This was a result of overaging and coarse precipitates in the softened region produced during the friction welding operation.     

铝/钢微束等离子熔钎焊接头组织及力学性能

采用微束等离子焊接方法进行6010铝合金/镀锌钢对接熔钎焊工艺试验,在合适的工艺参数下获得成形良好的铝/钢熔钎焊对接接头,采用金相显微镜、扫描电子显微镜、能谱仪、拉伸试验机等多种测试手段对所得接头形貌、微观组织及力学性能进行分析. 结果表明,所得接头焊缝正、背面铺展良好,无气孔、裂纹、夹渣等明显缺陷,为典型的铝/钢熔钎焊对接接头;接头界面处形成锯齿状的Fe₂Al₅金属间化合物,且金属间化合物层厚度和焊缝铺展宽度共同决定了接头强度,当焊接电流为38.5 A时,熔钎焊接头抗拉强度为193 MPa,为铝母材的79.8%,接头断裂形式为韧脆混合断裂.     

Mechanisms of joining aluminium A6061-T6 and titanium Ti–6Al–4V alloys by cold metal transfer technology

Abstract

Cold metal transfer (CMT) welding–brazing joining of Ti6Al4V and Al A6061-T6 was carried out using AlSi₅ wire. The joining mechanisms and mechanical properties of the joints were identified and characterised by scanning electron microscope, energy dispersive spectroscopy and tensile–shear tests. Desired CMT joints with satisfied weld appearances and mechanical properties were achieved by overlapping Ti on the top of Al. The joints had dual characteristics of a welding joint on the aluminium side and a brazing joint on the titanium side. Three brazing interfaces were formed for the joint, which increased the strength of the joint. An intermetallic compound layer was formed at the brazing interface, which included Ti₃Al, TiAl and TiAl₃. Two different fracture modes were also observed: one fractured at the welding/brazing interface and weld metal and the other at the Al heat affected zone (HAZ). Clearly, the joints fractured at the Al HAZ had higher tensile strength than those fractured at the welding/brazing interface and weld metal.