Effects of Ti2SnC on the mechanical properties and tribological properties of copper/graphite composites

Copper/graphite composites and copper/graphite/Ti₂SnC composites were fabricated through the process of ball-milling, pressing and sintering. The effects of Ti₂SnC as the second lubrication component on the mechanical properties, wear resistance and lubrication properties of copper/graphite composites were studied in this paper. The results showed that copper/graphite/Ti₂SnC composites had better hardness, impact toughness, wear resistance and lubrication performance than copper/graphite composites. The optimum values of hardness, impact toughness, friction coefficient and wear rate of copper/graphite/Ti₂SnC composites were, respectively, 56 HSD, 1.8J/cm², 0.15, 9.126 × 10^?6 mm³/N·m, while these were only 45 HSD, 1.2 J/cm², 0.17, 3.534 × 10^?4 mm³/N·m of copper/graphite composites.     

Unsaturated polyester resin/graphite nanosheet conducting composites with a low percolation threshold

In this study, the unsaturated polyester resin/graphite nanosheet conducting composites with a low percolation threshold of 0.64 vol% have been prepared via in situ polymerization under the application of ultrasonic irradiation. Two theoretical approaches (mean-field theory and excluded volume theory) are applied to interpret this low critical volume fraction and the latter can explain the low value better. The microstructures reveal that low value of percolation threshold may be mainly attributed to better conductive network consisting of graphite nanosheet with special morphology and there exists contact resistance in the percolating network formed within unsaturated polyester resin/graphite nanosheet composites. Furthermore, preliminary studies on the influence of graphite nanosheet on the thermal stability of the host unsaturated polyester resin have been performed.     

Mechanical and tribological properties of alumina-MWCNTs composites sintered by rapid hot-pressing

Alumina – MWCNTs composites were prepared using a novel approach. This process comprises functionalization of MWCNTs and stabilization of alumina-MWCNTs dispersion with subsequent freezing, which resulted in formation of granulated powders with homogeneous distribution of MWCNTs. The granulated powders were sintered by rapid hot pressing (RHP) at 1550 °C. Relative densities, microstructural analysis, tribological properties, fracture toughness and bending strength of prepared composites were investigated to reveal the effect of MWCNTs. Compared to pure alumina, bending strength and fracture toughness of dense alumina-5 vol.% MWCNTs composites decreased about 37% and 18%, respectively. At higher MWCNT contents, strength remained almost constant and fracture toughness slightly increased. Thus, the positive effect of CNTs on fracture toughness was demonstrated despite their counteracting effect on the refinement of the microstructure.     

Mechanical and tribological properties of TiB2-SiC and TiB2-SiC-GNPs ceramic composites

TiB₂-SiC and TiB₂-SiC-graphene nanoplatelets (GNPs) composites were prepared using field-assisted sintering technology at 2100 °C in argon atmosphere, and the influence of the SiC and different GNPs addition on microstructure development, mechanical and tribological properties has been investigated. Instrumented hardness, bending strength, chevron-notched fracture toughness and ball-on-flat tribological tests were used for the testing and characterization of the composites. The addition of SiC significantly improved the bending strength and elastic modulus with values of 601 MPa and 474 GPa, respectively, but decreased the fracture toughness with a value of 4.8 MPa.m^1/2. The addition of GNPs has a positive effect on fracture toughness and flexural strength but a negative one on the hardness. The increasing amount of both GNPs has a positive influence on wear characteristics of the composites thanks to the described wear mechanisms.     

Microstructure, magnetic and mechanical properties of Ni-Zn ferrites prepared by powder injection moulding

Nowadays, the electronic industry demands small and complex parts as a consequence of the miniaturization of electronic devices. Powder injection moulding (PIM) is an emerging technique for the manufacturing of magnetic ceramics. In this paper, we analyze the sintering process, between 900 °C and 1300 °C, of Ni-Zn ferrites prepared by PIM. In particular, the densification behaviour, microstructure and mechanical properties of samples with toroidal and bar geometry were analyzed at different temperatures. Additionally, the magnetic behaviour (complex permeability and magnetic losses factor) of these compacts was compared with that of samples prepared by conventional powder compaction. Finally, the mechanical behaviour (elastic modulus, flexure strength and fracture toughness) was analyzed as a function of the powder loading of feedstock. The final microstructure of prepared samples was correlated with the macroscopic behaviour. A good agreement was established between the densities and population of defects found in the materials depending on the sintering conditions. In general, the final mechanical and magnetic properties of PIM samples were enhanced relative those obtained by uniaxial compaction.     

Mechanical,electrical, and thermal properties of graphene nanosheet/aluminum nitride composites

Graphene nanosheet (GNS)/aluminum nitride (AlN) composites were prepared by hot-pressing and effects of GNSs on their microstructural, mechanical, thermal, and electrical properties were investigated. At 1.49 vol% GNSs content, the fracture toughness (5.09 MPa m^1/2) and flexural strength (441 MPa) of the composite were significantly increased by 30.17% and 17.28%, respectively, compared to monolithic AlN. The electrical conductivity of the composites was effectively enhanced with the addition of GNSs, and showed a typical percolation behavior with a low percolation threshold of 2.50±0.4 vol%. The thermal conductivity of the composites decreased with the addition of GNSs.     

Mechanical and thermal properties of graphite platelet/epoxy composites

Anhydride-cured diglycidyl ether of bisphenol A (DGEBA) reinforced with 2.5-5% by weight graphite platelets was fabricated. The structural, mechanical, viscoelastic and thermal properties of these composites were studied and compared. XRD studies indicated that the processing of composites did not change the original d-spacing of pure graphite. Tensile property measurements of composites indicated higher elastic modulus and tensile strength with increasing concentration of graphite platelets. The storage modulus and glass transition temperatures (T_g) of the composites also increased with increasing platelet concentration, however, the coefficient of thermal expansion decreased with the addition of graphite platelets. The thermal stability was determined using thermogravimetric analysis. The composites showed higher thermal stability in comparison with pure epoxy and increased char concentration for higher graphite concentration. The effects of reinforcement on the damage mechanisms of these composites were investigated by scanning electron microscopy.     

Preparation and thermal conductivity of novolac/Ni/graphite nanosheet composites

A high thermal conductivity novolac/nickel/graphite nanosheet (novolac/Ni/NanoG) composite was synthesized through in situ polymerization. Graphite nanosheet (NanoG) was prepared by sonicating expanded graphite (EG) in an aqueous alcohol solution and was plated with nickel through an electrodeposition method. The X‐ray diffraction spectrum shows that nickel was successfully plated onto the graphite surface and the nickel thickness is about 27.89 nm. The microstructures of the Ni/NanoG were characterized by scanning electron microscopy and transmission electron microscopy. The results reveal that nickel particles with the average diameter of 25 nm are coated on NanoG surface homogeneously and densely. Energy dispersive spectrometry spectrum confirms that the Ni content coated on NanoG surface, whose atomic percentage is 61%, is much higher than that of C element. The values predicted by theoretical model were underestimated the thermal conductivity of novolac/Ni/NanoG composites. Among NG, EG, NanoG, and Ni/NanoG four kinds of particles, the Ni/NanoG improved the thermal conductivity of novolac resin significantly. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Mechanical and thermal properties of ZrC/ZTA composites prepared by spark plasma sintering

In the present work, the influence of sintering temperature and particle size of pristine ZrC particles on the microstructure, mechanical properties, and thermal properties of ZrC/ZTA ceramic composites are investigated. Specimens consolidated by spark plasma sintering at different sintering temperatures from 1500 °C to 1800 °C. XRD results revealed that α-Al₂O₃, t-ZrO₂, ZrC, and a small quantity of m-ZrO₂ phases are present in the composites. The microstructure of μm-ZrC/ZTA is found to be more compact than nm-ZrC/ZTA composites. There is an apparent increase in the average grain size with the increase in temperature. From the micrographs of fracture surfaces, step-wise transgranular fracture structures are observed. Relative densities and Vickers hardness are in proportion to sintering temperature from 1500 °C to 1700 °C. The maximum Vickers hardness of 1919 HV1 is obtained for μm-ZrC/ZTA composites. Indentation fracture toughness displays a gradual rise when the temperature rises from 1500 °C to 1700 °C, then deteriorates at 1800 °C for both nm-ZrC/ZTA and μm-ZrC/ZTA ceramic composites. The maximum fracture toughness values for nm-ZrC/ZTA and μm-ZrC/ZTA are 6.75 MPa m^1/2 and 6.83 MPa m^1/2, respectively. The thermal conductivity of the specimens decreased gradually as the temperature increases from 100 °C to 1000 °C. The obtained results indicated that the 1700 °C is the optimized sintering temperature where μm-ZrC/ZTA composites have excellent performance on microstructure, mechanical properties, and thermal properties than nm-ZrC/ZTA composites.     

Characterizations of expanded graphite/polymer composites prepared by in situ polymerization

Poly(styrene-co-acrylonitrile)/expanded graphite composite sheets with very low in-plane (8.5 × 10⁻³ Ω cm) and through-thickness (1.2 × 10⁻² Ω cm) electrical resistivities have been prepared. The expanded graphite was made by oxidation of natural graphite flakes, followed by thermal expansion at 600 °C. Microscopic results disclosed that the expanded graphite has a legume-like structure, and each “legume” has a honeycomb sub-structure with many diamond-shaped pores. After soaking the expanded graphite with styrene and acrylonitrile monomers, the polymer/expanded graphite composite granules were obtained by in situ polymerization of the monomers inside the pores at 80 °C. The functional groups and microstructures of the oxidized graphite, expanded graphite and composites in the forms of particles or sheets were carefully characterized using various techniques, including X-ray powder diffraction, thermogravimetry, optical and electron microscopy. It was found that the honeycomb sub-structure survived after hot-pressing, resulting in a graphite network penetrating through the entire composite body, which produces a composite with excellent electrical conductivity.     

Mechanical and tribological properties of injection molded zirconia-alumina for orthopedic implants

Ceramics have gained great attention for hip and knee arthroplasty surgical procedures due to their ability to guarantee long-life performance in patients and are considered an alternative to existing metal systems.In the present study, zirconia toughened alumina (ZTA) for orthopaedic implants has been developed by Ceramic Injection Molding (CIM) process. Microstructural, mechanical and tribological studies have been carried out to establish whether the material is suitable for the purpose. The new CIM ZTA material obtained density up to 99.4%, toughness 6.1 MPa m^1/2, hardness 20 GPa, Young's modulus 320 GPa, and low coefficient of friction ranging between 0.08 and 0.13 under lubricated conditions, and between 0.11 and 0.34 in dry condition. To simulate the performance of the ZTA in vivo, i.e., the influence of material degradation on the ageing properties, accelerated hydrothermal aging was performed in vitro and good mechanical and tribological properties were confirmed for the developed ZTA.     

Improving the mechanical and tribological properties of TiB2/a-C nanomultilayers by structural optimization

A novel nanomultilayered architecture was developed through magnetron sputtering to simultaneously achieve excellent mechanical and tribological properties in TiB₂/a-C film. Structural optimization was conducted by adjusting the modulation period from 1 to 10.5 nm. Film hardness and toughness were significantly improved and reached the optimal value at Λ = 6.6 nm. Combination of a sufficient number of heterointerfaces and appropriate individual layer thickness played a key role in hardening and toughening. The internal stress increased linearly with the increase in modulation period, which may be related to the reduction in the number of interfaces. Furthermore, a low friction coefficient of about 0.1 was achieved in the steady state at Λ ≤ 6.6 nm due to the formation of a uniform and compact transfer film on the worn ball surface. The improved mechanical performance and the presence of an effective transfer film resulted in an outstanding anti-wear performance at Λ = 6.6 nm.     

Physical properties of graphite/aluminium composites produced by gas pressure infiltration method

Graphite/aluminium composites have been produced by means of gas pressure infiltration method. Two porous graphite preforms with a porosity of 10 and 13 vol%, respectively, have been infiltrated using either a commercially 99.85 pure aluminium or an AlSi7Mg alloy. Thermal expansion coefficient, electrical conductivity and flexural strength have been determined as a function of graphite preforms and metal matrices. To investigate the susceptibility of this composite system to thermal damage, specimens were thermally cycled between 60 and 300 °C up to 1020 cycles. Infiltrated graphites exhibited a significantly higher electrical conductivity (0.34-0.51 m/Ω mm²) compared to porous graphite preforms depending on graphite type and metal matrix. Thermal cycling did not influence electrical conductivity. The coefficients of thermal expansion of the composites were at least three times lower than for monolithic aluminium. Thermal cycling has reduced these values even more, most likely due to stress relaxation processes. The infiltration of porous graphite preforms with AlSi7Mg alloy or Al99.85 has increased the flexural strength of the composites resulting in values up to 105 MPa. The decrease in mechanical strength due to thermal cycling was about 10%.     

Preparation and properties of cyclopentadiene-containing monomer modified polydicyclopentadiene

A series of 1,4-dicyclopentadienylmethyl benzene (DMB) enhanced polydicyclopentadiene (DMB/polyDCPD blends) and 2,2′-dicyclopentadienyl ether (DCPE) toughened polyDCPD (DCPE/polyDCPD blends) were prepared via the ring-opening metathesis polymerisation (ROMP). The curing behaviour, thermal and mechanical properties were investigated. Differential scanning calorimetry (DSC) investigations of the DMB/polyDCPD blends showed the samples exhibited similar singular exothermic peak, and the exothermic peak of blends shifted to a higher temperature direction compared with the unfilled polyDCPD. However, the exothermic peak of the DCPE/polyDCPD blends presented two exothermic peaks. Dynamic mechanical analysis (DMA) measurements exhibited that the glassy modulus was enhanced as the DMB content increased. Thermal performance of DMB/polyDCPD has been enhanced with an increasing amount of DMB which was investigated by thermo gravimetric analysis (TGA) measurements. Whereas, the thermal stabilities of the DCPE/polyDCPD blends have been weakened with an increasing amount of DCPE. Moreover, the toughness of the DCPE/polyDCPD blends displayed a maximum performance at 60 wt% loading of DCPE.     

HDPE增韧PP-R/石墨复合材料力学性能的研究

采用高密度聚乙烯(HDPE)为增韧剂、乙烯 丙烯 二烯三元共聚物(EPDM)、乙烯 辛烯共聚物(POE)为相容剂、石墨为功能性助剂制备了以无规共聚聚丙烯(PP R)或嵌段共聚聚丙烯(PP B)为基体的PP R或PP B／HDPE／石墨复合材料。详细研究了HDPE含量、弹性体种类及含量对PP R或PP B／HDPE／石墨复合材料力学性能的影响。结果表明HDPE用量在20%、EPDM含量为5%时,PP R或PP B复合材料力学性能优异;POE可以实现PP R或PP B／HDPE／石墨复合材料力学性能的平衡。     

Microstructure evolution,mechanical and tribological properties of Ti3(Al,Sn)C2/Al2O3 composites

In this paper, in situ formed Ti₃(Al,Sn)C₂/Al₂O₃ composites were fabricated by sintering the mixture of Ti₃AlC₂ and SnO₂. The Al atoms could diffuse out of the Ti₃AlC₂ layered structure to react with SnO₂, resulting in the formation of Ti₃(Al,Sn)C₂ solid solution and Al₂O₃. When the SnO₂ content was 20?wt.%, the sintered Ti₃(Al,Sn)C₂/Al₂O₃ composite exhibited the best overall mechanical properties, because of the optimized cooperative strengthening effect of solution strengthening and Al₂O₃ enhancement. When the SnO₂ content increased up to 30?wt.%, the flexural strength and fracture toughness of Ti₃(Al,Sn)C₂/Al₂O₃ composite dramatically decreased on account of the large accumulation of generated Al₂O₃. Moreover, according to the SiC ball-on-flat wear tests, it was found that the wear resistance of Ti₃(Al,Sn)C₂/Al₂O₃ composites was significantly improved as the SnO₂ content increased.     

Mechanical and electrical properties of carbon nanofibers reinforced aluminum nitride composites prepared by plasma activated sintering

High density carbon nanofibers (CNFs) reinforced aluminum nitride (AlN) composites were successfully fabricated by plasma activated sintering (PAS) method. The effects of CNFs on the microstructure, mechanical and electrical properties of the AlN composites were investigated. The experimental results showed that the grain growth of AlN was significantly inhibited by the CNFs. With 2 wt.% CNFs added into the composites, the fracture toughness and flexural strength were increased, respectively to 5.03 MPa m^1/2 and 354 MPa, which were 20.9% and 13.4% higher than those of monolithic AlN. The main toughening mechanisms were CNFs pullout and bridging, and the main reason for the improvements in strength should be the fine-grain-size effect caused by the CNFs. The DC conductivity of the composites was effectively enhanced through the addition of CNFs, and showed a typical percolation behavior with a very low percolation threshold at the CNFs content of about 0.93 wt.% (1.51 vol.%).     

Near net-shape fabrication and properties of graphitic carbon foam with a continuous network of graphite nanosheets

A near net-shape graphitic carbon foam (GCF) with a continuous network of graphite nanosheets was prepared by direct carbonization of epoxy resin filled with nano-Al₂O₃. The effects of carbonization temperature on the properties of the resulting carbon foams were investigated by SEM, TEM, XRD, Raman, thermal conductivity and compression strength test. The results show that the as-prepared GCF can maintain well dimensional stability upon carbonization. The carbothermal reaction between the nano-Al₂O₃ and carbon foam matrix greatly influences the microstructure of carbon foam and promotes its growth of the continuous network of graphite nanosheets. In addition, the GCF prepared at 1700 °C possesses a compressive strength of 2.34 MPa with a bulk density of 0.19 g cm^-3, and meanwhile presents a high graphitization degree of 65.12% and a thermal conductivity of 2.02 W/mK. The continuous network of graphite nanosheets favors the enhancement of thermal conductivity of carbon foam and simultaneously prevents the decline of compressive strength further.     

Effect of Ti particle size on mechanical and tribological properties of TiCN coatings prepared by reactive plasma spraying

Titanium carbonitride (TiCN) coatings were successfully fabricated by reactive plasma spraying (RPS) from agglomerated Ti-graphite feedstock. The effect of Ti particle size on the microstructure and phase composition of plasma sprayed TiCN coatings was investigated. The Vickers microhardness of coatings was measured by a Microhardness Test and the corresponding Weibull distribution were also analyzed. In addition, a pin-on-disk tribometer was employed to determine the trobological properties of coatings. Results show that all the coatings consist of TiC_xN_1−x (0 ≤ x ≤1) and minor Ti₂O phases, and the amount of Ti₂O increases with the increase of Ti particle size. The Weibull distribution of Vickers microhardness of all the coatings shows apparent scattering, while the coating sprayed with Ti particle size of 28 µm exhibits a relatively even distribution. Compared with the coating sprayed with Ti particle size of 14 µm or 48 µm, the coating sprayed with Ti particle size of 28 µm exhibits improved mechanical and tribological properties, which are attributed to the high microhardness and strong bonding strength.