焊后热处理对输送H_2S介质压力管道维修焊接接头组织性能的影响

采用手工钨极氩弧焊(TIG焊)打底,焊条电弧焊(SMAW)填充、盖面的焊接工艺对输送H_2S介质压力管道(20钢)进行维修焊接,并对其焊接接头进行720～750℃下保温1h的焊后热处理.对热处理前、后焊接接头组织和性能进行分析研究,结果表明:720～750℃×1h热处理使焊缝区与热影响区成针状分布的魏氏组织铁索体晶粒得到细化,并使其呈退化形态;焊缝区、热影响区与母材的显微硬度整体呈下降趋势;焊接接头抗拉强度大幅度提高,断裂均处在远离焊缝的母材上.焊后热处理有效地降低了焊接接头的残余应力,改变了残余应力的分布特征,使其分布趋于"均匀",拉应力大幅度降低.     

Effect of initial base metal temper on mechanical properties in AA7050 friction stir welds

Abstract

The effect of initial base metal temper on mechanical properties in AA7050 friction stir welds was investigated. AA7050 plates, 6·4 mm thick, with three different heat treatment conditions (T7451, T62 and W), were friction stir welded using nearly identical welding parameters, followed by post-weld aging approximating a T7451 heat treatment. The microstructure, transverse hardness profiles and transverse tensile properties were characterised for these three welds. Experimental results show that preweld heat treatment conditions of AA7050 base metal have significant effect on the mechanical properties of the friction stir welds. Friction stir welding of AA7050 in the W condition, followed by post-weld aging, can change the fracture location from HAZ to weld nugget and increase tensile and yield strengths and elongation in transverse tension, relative to welding in T62 or T7451 conditions.     

Effects of Post-Weld Heat Treatment on Microstructure and Mechanical Properties of Al-12.7Si-0.7Mg Alloy Welded Joints by GMAW

In this study, 3-mm-thick hot-extruded plates of A1-12.7Si-0.7Mg alloy were used to fabricate the joints welded by gas metal arc welding. Effects of the post-weld heat treatment include solid solution treatment, water quenching, and artificial aging treatment on the microstructure, and mechanical properties of the weld joints have been investigated. Results showed that the welded joints after solid solution and artificial aging exhibited the increases in yield strength of 166 MPa and ultimate tensile strength of 148 MPa, respectively. Based on the microstructural observations, the associated mechanisms were discussed.     

焊后热处理对6063铝合金激光填丝焊接头组织与性能的影响

采用激光填丝焊对6063铝合金进行焊接,并对焊接接头进行人工时效和固溶+人工时效的热处理。通过光学显微镜、扫描电镜观察及拉伸试验,对焊后经不同热处理的焊接接头组织和性能进行研究。结果表明:未热处理的焊接接头抗拉强度为196 MPa,焊缝内部为铸态组织,弥散分布着Mg₂Si强化相,熔合线附近存在向焊缝内部生长的粗大柱状晶,焊缝内部为细小的树枝晶,焊缝中心为等轴晶;经时效处理后,焊接接头组织不均匀性和强化相的分布得到改善,焊接接头抗拉强度提高27 MPa;经固溶+时效处理的焊接接头抗拉强度提高64 MPa,焊缝组织、熔合区及热影响区组织得到显著细化。焊接接头均为韧脆混合断裂;时效处理的断口韧窝大小差异较大,韧窝较深;固溶+时效处理后的断口韧窝大小均匀,韧窝尺寸较大较深,韧窝数量更多。     

ZL114A铸铝搅拌摩擦焊接头性能

研究了采用不同焊接参数时ZL114A铸铝搅拌摩擦焊接头的金相组织、硬度分布及力学性能。结果表明，ZL114A铸铝的搅拌摩擦焊焊接性良好。焊核区的微观组织是无方向性的、细小的等轴晶粒。细化的硅粒子均匀布满整个焊核区。与粗大的树枝状母材相比，焊核晶粒细小、均匀而致密，没有观察到气孔等缺陷。焊缝区硬度分布较母材稳定，变化范围小。随着焊速增加，硅粒子所占体积比逐渐下降。热一机械影响区晶粒被拉长。接头的力学性能与焊接参数的匹配有关系。采用高焊速及转速与焊速比在3左右，获得的接头抗拉强度可达到母材的91％。焊后经T6热处理，可与同炉热处理母材等强。     

异质TC17线性摩擦焊接头焊后时效处理组织与性能

线性摩擦焊是制造航空发动机整体叶盘的关键技术. 通过光学显微镜、扫描电镜、电子式万能试验机及显微硬度仪对比分析了TC17(α + β)/TC17(β)钛合金线性摩擦焊接头焊态及不同时效温度下接头的组织与性能. 结果表明,焊态下焊合区及附近区域的微观组织为过冷β细晶,硬度最低;经焊后时效处理,析出了细小针状α相,硬度升高. 焊后时效温度为400 ℃时,焊合区及附近区域的硬度值明显提高,焊接区脆化. 焊后时效温度为630 ℃时,接头弯曲角度最高,但强度降低. 综合焊接接头的硬度、弯曲与拉伸性能优化出的焊后时效温度为550 ℃. 接头弯曲角度和抗拉强度分别达到母材的36%和95%. TC17(α + β)侧热力影响区( thermal-mechanical affected zone,TMAZ)受力后微观塑性变形更均匀,其强塑性能均优于TC17(β)侧TMAZ. 接头的弱化区对应于TC17(β)侧TMAZ硬度变化梯度及组织梯度最大的区域. 相比母材,接头的塑性损失比强度损失要大得多.     

Influence of pre- and post-weld heating on weldability of modified 9Cr–1Mo(V–Nb) steel pipe under shielded metal arc and tungsten inert gas welding processes

Abstract

Welding of modified 9Cr–1Mo(V–Nb) steel pipes has been carried out via shielded metal arc (SMA) and tungsten inert gas (TIG) welding processes. The weld joints have been produced using different preheating temperatures, followed by post-weld heat treatment (PWHT) at various temperatures. The microstructures of the weld and of the heat affected zone (HAZ) of the weld joints have been studied under the optical microscope and correlated with the preheating and PWHT. The average hardness of the weld and different regions of the HAZ, and tensile properties of the weld joints have also been studied and correlated with the preheating and PWHT. The tensile properties of the SMA and TIG weld joints produced using preheating and PWHT at various temperatures are compared and correlated with their microstructures. It is noted that a comparatively high preheating temperature of the order of 573 K is beneficial, and PWHT is necessary to reduce the susceptibility to cold cracking of weld joints of the present steel. The PWHT at 1123 K enhances ductility to fracture, but decreases the tensile strength of the base material, causing fracture of both the SMA and TIG weld joints from this region close to the HAZ. The tensile properties of SMA welds are found to be superior to those of the TIG welds, especially for PWHT at temperatures up to 1023 K.     

中国低活马氏体钢熔化焊接头硬度与微观组织

针对4 mm厚的中国低活马氏体钢,采用TIG焊接方法分别对预热和未预热两组试样进行了焊接和焊后回火处理,对焊接接头的硬度和微观组织结构进行了测试和观察.结果表明,焊缝区硬度值偏高,靠近母材的热影响区出现较窄的软化带;焊接接头金相组织为板条特征明显的回火马氏体组织,未预热试样的马氏体含量与预热试样相比较,两者之间没有明显的差异.在晶内和晶界处分布大量的碳化物,焊缝区为尺寸较小的棒状,母材和热影响区为尺寸较大的颗粒状,接头的组织和碳化物的析出对焊接接头的硬度有很大的影响.

Abstract：

The preheated and non-preheated 4 man China low activation martensitic steel (CLAM) plate were welded by TIG welding and post-weld heat treating, and the hardness and micrcstructure in welded joint were tested and observed. The results show that the hardness in the weld metal is higher and the softening band in the heat-affected zone (HAZ) closing to the base metal. The tempered lath martensite is observed in welded joints. There is no significant difference in martensite content between the preheated and non preheated weldments. A large amount of carbide particles are observed in the grains and at the grain boundary. The carbides are small rods in weld metal and large granular in the HAZ and base metal respectively. The mierostrueture and carbides in welded joints have great effect on the hardness.     

Tensile Properties and Fusion Zone Hardening for GMAW and MIEA Welds of a 7075-T651 Aluminum Alloy

Tensile and hardness values for 7075-T651 aluminum alloy in the as welded and post weld heat treated conditions（solubilization and artificial aging-T6）,obtained using GMAW and modified indirect electric arc（MIEA）welding processes are presented.Results showed that the base material along rolling direction exhibited a tensile strength of around 600 MPa and elongation of 11%.For the as welded condition,tensile strength was 260 MPa and elongation percent of 3%.This behavior was attributed to brittleness induced by the microstructural characteristics of the welded alloys,as well as high porosity.Hardness profiles along the welds were obtained and different welded zones were identified.A soft zone（＊100 HV0.1） in the heat affected zone for GMAW and MIEA was observed,the minimum hardness corresponding to weld metal（＊85 and ＊96 HV0.1for GMAW and MIEA,respectively）.The high dilution between filler and base metal during welding in MIEA allows to the Zn and Cu to flow from the base metal into the weld metal,inducing hardening by solution and subsequent artificial aging.In this regard,the hardness of the weld metal for MIEA increases by 56%,while the tensile strength reaches a value close to 400 MPa.For GMAW,non-favorable hardening effect was observed for the weld metal after solution and artificial aging.     

TC17钛合金线性摩擦焊接头组织及力学性能分析

针对固溶时效态TC17钛合金焊态及焊后热处理态线性摩擦焊接头,进行显微组织及力学性能对比分析. 结果表明,焊态时焊缝组织发生了回复与再结晶,由于焊后冷却速度较快,生成了亚稳定β相,焊缝区发生了软化;热力影响区组织沿受力变形方向拉长、细化、交替呈带状分布,加工硬化程度较高,显微硬度明显高于其它区域;热影响区由于二次次生α相基本溶解于亚稳定β相,导致显微硬度显著降低. 经过焊后热处理,亚稳定β相发生时效分解,析出了弥散程度更高的针状次生α相使得焊接区硬度大幅度提高. 由于亚稳定相的生成,焊态接头发生软化,拉伸均断裂在焊缝区,抗拉强度达到母材强度91.8%,断口呈脆性断裂形态;焊后热处理态接头由于二次次生α相的析出,起到弥散强化的作用,拉伸试验均断在母材,断口呈典型韧性断裂形态.     

Effect of post-weld heat treatment on microstructure and mechanical properties of welded joints of 6061-T6 aluminum alloy

6061 aluminum alloy T-joints were welded by double-pulsed MIG welding process. Then, the post-weld heat treatment was performed on the welded T-joints. The weld microstructure under different aging temperature and time was investigated by transmission electron microscopy and scanning electron microscopy. The mechanical properties were examined by hardness test and tensile test. The results showed that the micro-hardness was sensitive to heat treatment temperature and time. Increasing temperature was beneficial to the shortening of peak aging time. There were a large number of dislocations and few precipitates in the welded joints. With the increase of post-weld heat treatment temperature and time, the density of dislocation decreased. Meanwhile, the strengthening phase precipitated and grew up gradually. When the post-weld heat treatment temperature increased up to 200 °C, large Q' phases were observed. And they were responsible for the peak value of the micro-hardness in the welded joints.     

时效处理对铝锂合金电子束焊接头耐蚀性能的影响

对铝锂合金电子束焊接头进行焊后热处理,研究了时效处理前后接头各区域的晶间腐蚀、剥蚀和电化学腐蚀行为。结果表明,接头经过时效处理后,焊缝晶界析出的T1(Al_2CuLi)相数量增加,并且形成了明显的晶界无沉淀带(Precipitate Free Zone,PFZ)。焊态下接头未出现晶间腐蚀,热影响区和母材区均出现了孔蚀;焊后时效处理增大了接头的晶间腐蚀倾向,热影响区同时发生了孔蚀和晶间腐蚀,母材区出现了严重的晶间腐蚀。焊态下焊缝和热影响区均具有优异的抗剥蚀能力,母材区对剥蚀的敏感性较高;焊后时效处理可提高接头母材区的抗剥蚀能力,但会增大热影响区的剥蚀敏感性。电化学腐蚀测试表明,与时效后的接头焊缝相比,焊态下焊缝的自腐蚀电位较高,腐蚀电流密度小,具有相对较好的耐蚀性。     

焊前热处理对440C不锈钢电子束焊接接头组织与性能的影响

研究了焊前退火和调质2种热处理工艺对440C不锈钢电子束焊接接头的组织和力学性能的影响,分析了2种状态下的组织演变规律、接头拉伸力学性能和硬度分布特点. 结果表明:2种热处理状态的板材经过电子束焊接后,焊缝成形良好,焊缝区域均为马氏体和残留奥氏体组织,呈现出非平衡凝固组织,碳及合金元素以固溶形式存在于马氏体及残余奥氏体中,焊缝区域硬度达到398 HV. 焊前经调质热处理后,母材基体由铁素体转变成回火马氏体和残余奥氏体混合组织,同时部分碳化物固溶在基体组织中,使基体组织硬度提高了60％. 与焊前退火态相比,焊前调质热处理板材经电子束焊接后,可使焊接接头抗拉强度提高20％,焊接热影响区硬度提高35％,但接头的塑性变形能力有所下降,断裂均发生在热影响区.     

焊后热处理对Al-Zn-Mg-Cu合金MIG焊接接头组织与性能的影响

采用ER5356焊丝对Al-4.6Zn-1.5Mg-0.15Cu合金板材进行熔化极钨极氩弧焊试验,并对焊接接头进行了不同的焊后热处理。借助光学显微镜(OM)、扫描电镜(SEM)研究不同焊后热处理试样的组织变化规律,并进行了显微硬度测试与拉伸试验。结果表明:经固溶加时效处理后,焊接接头抗拉强度与显微硬度得到明显提升,抗拉强度与焊缝硬度均值分别提高至304 MPa与85 HV,相比焊后未处理的263 MPa与66 HV,增幅分别达15.6%与28.8%。焊接接头经时效处理后,组织的不均匀性及强化相的分布得到改善;而经重新固溶后,第二相发生回溶,再经时效处理将使得一部分不稳定的过饱和固溶体重新析出且弥散分布。     

激光焊接热输入对Ti2AlNb合金组织性能的影响

研究激光焊接热输入对Ti-22Al-27Nb(at%)合金焊缝成形和力学性能的影响,利用OM、SEM、XRD和TEM等手段对焊接接头的显微组织特征进行了分析,并探讨了焊后热处理对焊接接头组织性能的影响。结果表明,连续激光焊接可以获得无缺陷、成形良好的焊接接头。焊缝区域组织主要为柱状的B2相,柱状晶的生长方向垂直于熔合线。焊缝和热影响区的显微硬度要高于母材,焊缝的平均显微硬度最高。随着热输入的增加,焊接接头的室温抗拉强度增加,但是焊接接头的延伸率较低。焊接接头650℃高温强度为母材的71%~75%,塑性则仅为母材塑性的40%左右。经过焊后热处理,焊缝由B2+O相组成。O相增多使得焊缝的室温强度略有提高,且提高了650℃高温拉伸性能,高温抗拉强度最高可达母材的87.5%。     

TC4钛合金线性摩擦焊接头组织和力学性能

文中阐述了线性摩擦焊的原理、特点,并针对TC4钛合金线性摩擦焊接头组织和力学性能进行了研究.对比分析TC4钛合金线性摩擦焊接头焊态和焊后热处理态的接头组织和力学性能.结果表明,焊接接头共分为母材、热力影响区和焊缝区三部分;TC4钛合金的接头(包括焊态和焊后热处理态)抗拉强度和屈服强度均达到母材的90%以上;焊缝中心的硬度值最高,焊后热处理能使接头的硬度分布更加均匀.     

Effect of post-weld heat treatment on joint properties of dissimilar friction stir welded 2024-T4 and 7075-T6 aluminum alloys

The effect of post-weld heat treatment on dissimilar friction stir welded AA7075 and AA2024 joints was studied. After welding in constant parameters, solution heat treatment and various aging treatments were given to the welded joints. Microstructural and phase characterizations were done using optical microscope, SEM, FE-SEM, XRD and EDS techniques. Finally, mechanical properties of post-weld heat treated joints were evaluated and compared with as-welded joints. Results show that both 2024-T6 and 7075-T6 post-weld heat treatment procedures considerably improve the mechanical strength of the welded joint, with higher strength obtained for the 7075-T6 procedure, in comparison with the as-welded joint. This is explained by the formation of fine precipitates during the aging process, despite the abnormal grain growth. Fracture occurs at the interface between thermo-mechanical affected zone (TMAZ) and heat affected zone (HAZ) on the retreating side (AA7075) of as-welded joint, while by applying post-weld heat treatment fracture location shifts towards the stir zone (SZ) of the welded joint. Also, for post-weld heat treated samples, fracture surface is predominantly inter-granular, while in as-weld joint, fracture surface is mostly trans-granular. This is explained by dissolution and coarsening of precipitates within grains in post-weld heat treated joints.     

Microstructural characteristics and mechanical properties of Al–Mg–Si alloy self-reacting friction stir welded joints

The 5?mm thick Al–Mg–Si alloy was self-reacting friction stir welded using the specially designed tool at a constant rotation speed of 400?rev?min^?1 with various welding speeds. Defect-free welds were successfully obtained with welding speeds ranging from 150 to 350?mm?min^?1, while pore defects were formed in the weld nugget zone (WNZ) at a welding speed of 450?mm?min^?1. Band patterns were observed at the advancing side of WNZ. Grain size and distribution of the precipitated phase in different regions of the joints varied depending on the welding speed. The hardness of the weld was obviously lower than that of the base metal, and the lowest hardness location was in the heat affected zone (HAZ). Results of transverse tensile tests indicated that the defective joint fractured in the WNZ with the lowest tensile strength, while the fracture location of the defect-free joints changed to the HAZ.     

两种TIG焊工艺对LD10接头力学性能的影响

对5.5 mm厚度的LD10(2A14-T6)铝合金进行了两种工艺的TIG焊接,采用热电偶测定了接头的热循环曲线,分析了不同工艺对接头力学性能的影响.结果表明,两面三层焊热影响区中同一点先后经历三次热循环,导致过时效区硬度大幅下降,拉伸时断裂于此;焊缝区各层所经历的热过程不同,导致其硬度起伏较大.与两面三层焊相比,单面两层焊有更高的抗拉强度,为358.3 MPa,热影响区范围窄,且过时效区硬度比三层焊时高,但焊缝中气孔和晶界网状分布的第二相的存在使焊缝和接头的塑性相对降低.     

AZ71镁合金TIG焊焊接接头微观组织与力学性能

采用钨极氩弧焊接方法对2.2mm厚镁合金AZ71薄板进行焊接加工。焊后对接头进行拉伸试验和硬度测试,结果表明:采用90A的电流焊接时,接头抗拉性能最好(281.23MPa),达到母材的89.58%。断裂发生在焊缝区,焊接接头断口呈准解理断口,接近解理断口;母材断裂为延性断裂,断口呈韧窝断口;焊缝区显微硬度最高,其次是母材,热影响区硬度最低。