Electrical insulation characteristics of alumina,titania, and organoclay nanoparticles filled PP/EPDM nanocomposites

In this study, nanofillers composed of alumina, titania, and organoclay were separately embedded in 50% polypropylene (PP) and 50% ethylene propylene diene monomer (EPDM) blends. Several formulations of PP/EPDM nanocomposites were prepared using an internal mixer and were molded using a compression mold to produce test samples. The effects of filler loading (2, 4, 6, and 8 vol %) on the dielectric breakdown strength, dielectric properties, hydrophobicity, and flammability were determined. The addition of nanofillers improved the breakdown strength (up to 2 vol %) and increased the dielectric constant and dielectric loss of the PP/EPDM nanocomposites. The hydrophobicity of PP/EPDM/Al₂O₃ increased, whereas the hydrophilicity of PP/EPDM/TiO₂ and PP/EPDM/organoclay increased. Flammability test results showed that PP/EPDM/TiO₂ had a lower burning rate than PP/EPDM/Al₂O₃ and PP/EPDM/organoclay. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 41184.     

Properties of nanofillers/crosslinked polyethylene composites for cable insulation

In this work, we report the effect of nanofillers and filler loading on mechanical, physical, dielectric, and thermal properties of the crosslinked polyethylene (XLPE) matrix. XLPE filled with 0.5–2% of zinc oxide (ZnO), aluminium oxide (Al₂O₃), and organoclay (OMMT) nanofillers prepared by melt mixing with a single screw extruder followed by hot press moulding. Nanocomposites were tested as per ASTM standard methods and characterized with tensile test, water absorption, linear rate of burning, dielectric breakdown strength, and thermal stability. Scanning electron microscopy (SEM) was used to examine the surface morphology of the nanocomposites. The results showed that addition of nanofillers improved tensile strength, elongation at break, Young's modulus, burning rate, dielectric breakdown strength, and decomposition temperature. However, water absorption increased with time due to the hydrophilic properties of nanofillers. In general, based on the properties measured Al₂O₃ exhibits the highest properties than those of ZnO and OMMT nanofillers. Addition of 1.5% of Al₂O₃ in XLPE matrix has led to the improvement in tensile strength, elongation at break, Young's modulus, burning rate, and dielectric breakdown strength as compared to the unfilled polymer. J. VINYL ADDIT. TECHNOL., 25:E147–E154, 2019. © 2018 Society of Plastics Engineers     

Largely improved toughness of PP/EPDM blends by adding nano-SiO2 particles

As a part of long-term project aimed at super polyolefin blends, in this work, we report the toughness and phase morphology of polypropylene (PP)/EPDM/SiO₂ ternary composites. Two processing methods were employed to prepare PP/elastomer/filler ternary composites. One was called one-step processing method, in which the elastomer and the filler directly melt blended with PP matrix. Another one was called two-step processing method, in which the elastomer and the filler were mixed first, and then melt blended with pure PP. Two kinds of PP (grafted without or with maleic anhydride (PP-g-MA)) and SiO₂ (treated with or without coupling agent) were used to control the interfacial interaction among the components. The dependence of the phase morphology on interfacial interaction and processing method was investigated. It was found that the formation of filler-network structure could be a key for a simultaneous enhancement of toughness and modulus of PP and its formation seemed to be dependent on the work of adhesion (W_AB) and processing method. As the W_AB of PP/EPDM interface was much lower than that of PP/SiO₂ and EPDM/SiO₂, and the two-step processing method was used, the formation of filler-network structure was favorable. In this case, a super toughened PP ternary composite with the Izod impact strength 2-3 times higher than PP/EPDM binary blend and 15-20 times higher than pure PP could be achieved.     

Study on the phase structures and toughening mechanism in PP/EPDM/SiO2 ternary composites

In this paper, EPDM rubber and nano-SiO₂ particles were employed to modify PP simultaneously. Our goal was to control the distribution and dispersion of EPDM and nano-SiO₂ particles in PP matrix by using an appropriate processing method and adjusting the wettability of nano-SiO₂ particles toward PP and EPDM, so as to achieve a simultaneous enhancement of toughness and modulus of PP. With regard to this, two kinds of nano-SiO₂ particles (with hydrophilic or hydrophobic) as well as two processing methods (one-step or two-step) were employed to prepare PP/EPDM/SiO₂ ternary composites. A unique structure with the majority of EPDM particles surrounded by SiO₂ particles was first observed by using hydrophilic SiO₂ and two-step processing method, resulting in a dramatically increase of Izod impact strength as the rubber content in the range of brittle-ductile transition (15-20 wt%). The observation that poor adhesion and poor compatibility between particles and PP matrix could result in a significant increase in Izod impact strength was unusual and needed further investigation. This could be tentatively understood as a consequence of the overlap of the ‘stress volume’ between EPDM and SiO₂ particles due to the formation of the unique structure. Our work provided a deep understanding of the toughening mechanism and a new way for the preparation of high performance polymer composites.     

Morphology and properties of PP/EPDM binary blends and PP/EPDM/nano‐CaCO3 ternary blends

In this article, the morphology, crystallization, and rheological behaviors of polypropylene (PP)/ethylene‐propylene‐diene terpolymer (EPDM) binary blend and PP/EPDM/calcium carbonate nanoparticles (nano‐CaCO₃) ternary blend were investigated. Two processing methods, i.e., direct extrusion and two‐step extrusion, were employed to prepare the PP/EPDM/CaCO₃ blend. The influence of EPDM and nano‐CaCO₃ respectively on phase morphology and properties of PP/EPDM blend and PP/EPDM/CaCO₃ blend were characterized by scanning electron microscopy (SEM), differential scanning calorimetry (DSC) and dynamic rheometer. The crystallinity and crystallization temperature of PP/EPDM blend were improved in comparison to pure PP due to addition of EPDM, but kept invariable with the increased EPDM loading. As the EPDM content was increased, the mobility of PP molecular chains was weakened. Compared with direct extruded blend, less and finer nano‐CaCO₃ was dispersed in matrix of two‐step extruded blend. Accordingly, the increased nano‐CaCO₃ in matrix gave rise to a weaker increment in crystallinity and crystallization temperature of two‐step extruded blend, and a later platform of tanδ curve. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Nano-BN/Nano-TiO2 and micro Mg(OH)2 loaded hybrid ethylene propylene diene monomer elastomer composites for outdoor high-voltage insulation application

This work deals with the synthesis, characterization of hybrid ethylene propylene diene monomer (EPDM) composites loaded with nano-boron nitride (nano-BN)/nano-titanium dioxide (nano-TiO₂) and micro Mg(OH)₂ particles for its suitability towards high-voltage insulation application. The elastomer samples were prepared by carefully dispersing the micro and nano fillers during the mastication process of EPDM polymer using a two roll mill, followed by vulcanization. The samples were characterized for mechanical, morphological, thermal, and electrical insulation properties. The highest tensile strength among the composite samples was noted for 1 phr nanoparticles loaded samples. Fourier Transform Infrared (FTIR) results show no change in the chemical moiety upon addition of nano-BN/nano-TiO₂ in EPDM composites. Enhancement in hydrophobicity is observed for 3 phr nano-TiO₂ loaded composites, which shows a maximum static contact angle of 110°. Meanwhile remarkable enhancement in the thermal conductivity and volume resistance of the composites are contributed to the addition of nano-BN, thereby achieving maximum dielectric breakdown voltage (i.e., ~21 kV/mm for EMB3). Scanning electron microscope images and atomic force microscopy (AFM) topography highlight that low concentration (i.e., 1 phr) based composites have homogeneous dispersion in matrix and excessive nano filler addition deteriorates properties by forming filler aggregates and increasing surface roughness.     

The Effects of Dynamic Vulcanization by Dicumyl Peroxide (DCP) and N,N-m-Phenylene Bismaleimide (HVA-2) on the Properties of Polypropylene (PP)/Ethylene-Propylene Diene Terpolymer (EPDM)/Natural Rubber (NR) Blends

ABSTRACT

This paper discusses some properties of the polypropylene (PP)/ethylene-propylene diene terpolymer (EPDM)/natural rubber (NR) blends, such as tensile properties, heat resistance, gel content, and morphology. Dicumyl peroxide (DCP) and N,N-m-phenylene bismaleimide (HVA-2) and their combination were applied in PP/EPDM/NR blends as cross-link agents. In terms of tensile properties, the combination of DCP with HVA-2 shows the highest tensile strength and elongation at break in all PP/EPDM/NR blend ratios compared to similar blends, except with DCP or HVA-2 alone. The addition of HVA-2 produced blends with good heat resistance, while the combination of DCP with HVA-2 shows the highest gel content dealing with the cross-links formation. SEM micrographs from the surfaces extraction of the blends support that the cross-links have occurred during dynamic vulcanization process.     

Significant enhancement in breakdown strength and energy density of the BaTiO3/BaTiO3@SiO2 layered ceramics with strong interface blocking effect

The BaTiO₃/BaTiO₃@SiO₂ (BT/BTS) ceramics with layered structure, where grain size was about 1–2 μm in the BT layer while it was about 300–400 nm in the BTS layer, were fabricated by the tape-casting and lamination method. With the increasing of SiO₂ content in the BTS layer, the dielectric constant decreased gradually, and the breakdown strength was remarkably improved. Compared to the SiO₂-added BaTiO₃ bulk ceramics, the layered ceramics displayed significant enhancements in dielectric properties, breakdown properties and energy storage properties. The enhancement in dielectric properties was mostly attributed to the diluting effects created by this structure to SiO₂. Based on the finite element analysis with the dielectric breakdown mode, it was regarded that the electric field redistribution and the interface blocking effect led to the enhancement of breakdown strength. Finally, the maximum energy density of 1.8 J/cm³ was obtained at a breakdown strength of 301.4 kV/cm for the BT/BTS3 ceramic.     

Dynamic rheology–morphology relationship of PP/EPDM blends prepared by melt mixing under Sc-CO2

It was demonstrated that the high mixing efficiency of twin screw extruder (TSE) helped to disperse the ethylene–propylene–diene terpolymer (EPDM) domains in polypropylene (PP) matrix, but could not lead to the uniform distribution of EPDM phase with small sizes because of the thermodynamical immiscibility between PP and EPDM. So supercritical carbon dioxide (Sc-CO₂) was environmentally and economically introduced to the twin screw extrusion to assist the melt mixing of PP and EPDM. The scanning electron microscopy photographs showed that co-continuous phase morphology was formed to some extent for the PP/EPDM 60/40 blend prepared with Sc-CO₂, especially with 2.5 wt% Sc-CO₂. This was the one important reason for that the complex viscosity and storage modulus of PP/EPDM 60/40 blend increased with the increase of Sc-CO₂ concentration.     

Effect of the mixing sequence on the morphology and properties of a polypropylene/polydimethylsiloxane/nano‐SiO2 ternary composite

Ternary composites of polypropylene (PP), polydimethylsiloxane (PDMS) elastomer, and nano‐SiO₂, prepared with three different mixing sequences, were studied for dispersion morphology and its effect on the crystallization of PP and the mechanical properties. The mixing sequence produced a significant effect on the dispersion morphology and, thereby, on the mechanical properties of the composites. A two‐step mixing sequence, in which nano‐SiO₂ was added in the second step to the PP/PDMS binary system, produced a significant encapsulation of nano‐SiO₂ by PDMS, and this, in turn, resulted in the poor modulus and impact strength of the composite. A one‐step mixing sequence of all three components produced a separated dispersion of PDMS and nano‐SiO₂ phases in the PP matrix with the occurrence of a fine band of nano‐SiO₂ particles at the boundaries of the PDMS domains and the presence of some nano‐SiO₂ filler particles inside the PDMS domains. This one‐step mixing sequence produced an improvement in the tensile modulus but a decrease in the impact strength with increasing nano‐SiO₂ content. In the third sequence of mixing, which involved a two‐step mixing sequence through the addition of PDMS in the second step to the previously prepared PP/nano‐SiO₂ binary system, the morphology of the dispersion showed separately dispersed PDMS and nano‐SiO₂ phases with a loose network of nano‐SiO₂ particles surrounding the PDMS domains. This latter series of ternary composites had the highest impact strength and exhibited high shear deformation under tensile and impact conditions. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

PET/PC blends: Effect of chain extender and impact strength modifier on their structure and properties

Methylene diphenyl diisocyanate (MDI) affects the morphology, rheological, mechanical, and relaxation properties, as well as tendency to crystallize of PET in PET/PC/(PP/EPDM) ternary blends produced by the reactive extrusion. Irrespective of the blend phase structure, the introduction of MDI increases the melt viscosity (MFI dropped), resulting from an increase in the molecular weight of the polymer chains; the PET crystallinity was also reduced. MDI favors compatibility of PET with PC in PET/PC/(PP/EPDM) blends. This is explained by intensified interphase interactions on the level of segments of macromolecules as well as monomer units. The presence of MDI causes a substantial rise in the dynamic shear modulus within the high‐elastic region of PET (for temperature range between T_g,PET and that of PET cold crystallization); the processes of PET cold crystallization and melt crystallization become retarded; the glass‐transition temperatures for PET and PC become closer to each other. MDI affects insignificantly the blend morphology or the character of interactions between the disperse PP/EPDM blend and PET/PC as a matrix. PP/EPDM reduces the intensity of interphase interactions in a PET/PC/(PP/EPDM), but a rise in the degree of material heterogeneity. MDI does not change the mechanism of impact break‐down in the ternary blends mentioned above. Increased impact strength of MDI‐modified materials can be explained by higher cohesive strength and resistance to shear flow at impact loading. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Fumed SiO2 nanoparticle reinforced biopolymer blend nanocomposites with high dielectric constant and low dielectric loss for flexible organic electronics

In the present study, fumed silica (SiO₂) nanoparticle reinforced poly(vinyl alcohol) (PVA) and poly(vinylpyrrolidone) (PVP) blend nanocomposite films were prepared via a simple solution‐blending technique. Fourier transform infrared spectroscopy (FTIR), ultraviolet–visible spectroscopy (UV–vis), X‐ray diffraction (XRD), and scanning electron microscopy (SEM) were employed to elucidate the successful incorporation of SiO₂ nanoparticles in the PVA/PVP blend matrix. A thermogravimetric analyzer was used to evaluate the thermal stability of the nanocomposites. The dielectric properties such as dielectric constant (?) and dielectric loss (tan δ) of the PVA/PVP/SiO₂ nanocomposite films were evaluated in the broadband frequency range of 10^?2 Hz to 20 MHz and for temperatures in the range 40–150 °C. The FTIR and UV–vis spectroscopy results implied the presence of hydrogen bonding interaction between SiO₂ and the PVA/PVP blend matrix. The XRD and SEM results revealed that SiO₂ nanoparticles were uniformly dispersed in the PVA/PVP blend matrix. The dielectric property analysis revealed that the dielectric constant values of the nanocomposites are higher than those of PVA/PVP blends. The maximum dielectric constant and the dielectric loss were 125 (10^?2 Hz, 150 °C) and 1.1 (10^?2 Hz, 70 °C), respectively, for PVA/PVP/SiO₂ nanocomposites with 25 wt % SiO₂ content. These results enable the preparation of dielectric nanocomposites using a facile solution‐casting method that exhibit the desirable dielectric performance for flexible organic electronics. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 44427.     

Thermal aging on ethylene–propylene–diene rubber composites reinforced by samarium oxide,samarium borate and Sb in Sb doped SnO2

Abstract

Ethylene–propylene–diene monomer (EPDM) rubber composites reinforced with 50 phr samarium oxide (Sm₂O₃), samarium borate (SmBO₃) and Sb in antimony doped tin oxide (ATO) are aged at 150°C for different intervals. It is found that neutral Sm₂O₃ and alkaline SmBO₃ can retard the oxidative degradation of EPDM by blocking radical passage. The acidic ATO particles can accelerate the oxidative degradation of EPDM. The trend of tensile strength of EPDM composites is consistent with that of cross-link density of EPDM composites. SmBO₃ and ATO can retard the increase of dielectric loss until 10 days of aging, while Sm₂O₃ can keep the dielectric loss at low level until 14 days of aging. The increased surface charge of filler can make surface and volume resistivity decrease sharply. Antimony doped tin oxide can deteriorate the dielectric strength of EPDM, while SmBO₃ and Sm₂O₃ can keep the dielectric strength of EPDM at a constant level.     

Novel approach to fibrillation of LCP in an LCP/PP blend

A novel concept of improving shear‐induced fibrillation of liquid crystalline polymer (LCP) in LCP/thermoplastic blend systems was introduced. Silica fillers (SiO₂) were added to an LCP/polypropylene (PP) system to serve as a viscosity thickening agent and to improve the fibrillation of the LCP phase. The formation of LCP fibrils was found to enhance with the incorporation of 5–15 wt % of fillers. The presence of LCP fibrils improved the flow properties of the LCP/PP/SiO₂ composites. It was evident from the rheological and morphological studies that the addition of silica led to an increase of the aspect ratio of the LCP fibrils, which, in turn, should improve their effectiveness as reinforcements and/or toughening agents. Substantial improvement in LCP aspect ratio was achieved by the introduction of hydrophobic SiO₂ fillers in the PP/LCP blends. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2070–2078, 2002     

Modification of Ethylene Propylene Diene Terpolymer Rubber by Some Thermoplastic Polymers

Abstract

Blends of ethylene propylene diene terpolymer (EPDM) rubber with thermoplastic polyolefins such as low‐density polyethylene (LDPE), high‐density polyethylene (HDPE), high molecular weight polypropylene (PP), and polypropylene random copolymer grade (PP‐R) were prepared by melt mixing. The physico‐mechanical properties, equilibrium swelling in benzene, and aging properties of the binary blends were investigated, analyzing the effect of the rubber/thermoplastics ratio and the type of the thermoplastic material on these properties. The data obtained indicate that EPDM/PP‐R blend in 20/80 w/w% shows the highest physico‐mechanical properties with improved retained tensile strength at 90°C for 7 days. This blend ratio also gives excellent retained equilibrium swelling in benzene at room temperature for 7 days, although EPDM/LDPE blend in 80/20 w/w% imparts the highest retained elongation at break at 90°C for 7 days.     

Distribution of oil in olefinic thermoplastic elastomer blends

The distribution of processing oil in two olefinic thermoplastic elastomer (OTPE) blends was determined using dielectric spectroscopy. The OPTE blends are blends of dynamically vulcanised EPDM with polypropylene (PP), TPVs, and blends of PP with SEBS. Both blend types contain paraffinic oil, which is present in both the PP and in the elastomer phase. The determination of the actual oil concentration by measuring the reduction in the glass transition temperatures (T_g) is inaccurate using DSC or DMA, because the glass transition dynamics of the two phases overlap. The blends were made sensible for dielectric spectroscopy by the addition of a probe molecule. The oil distribution was determined by modelling of the dielectric loss of the OPTE blends in the T_g regime from the ones of the binary mixtures. The mean value for the oil distribution coefficient was found to be 0.6 for PP/SEBS blends and 0.63 for TPVs.     

Natural rubber/ethylene propylene diene blends for high insulation iron crossarms

This research studied the composition and behavior of natural rubber (NR) and ethylene propylene diene monomer (EPDM) blends at various carbon black concentrations (0–30 phr) in terms of electrical resistivity, dielectric breakdown voltage testing, and physical properties. The blends having electrical properties suitable for application in high‐insulation iron crossarms were selected for investigation of compatibility and increased physical properties. The effect of the homogenizing agent concentration on improvement of compatibility of blends was studied by scanning electron microscopy, pulsed nuclear magnetic resonance spectroscopy, and rheology techniques. We also examined mechanical properties such as tensile strength, tear strength, elongation at break, and hardness. The NR/EPDM blends filled with a fixed concentration of silica were investigated for ozone resistance. A carbon black content as high as 10 phr is still suitable for the insulation coating material, which can withstand electrical voltage at 10 kVac. Addition of the homogenizing agent at 5 phr can improve the mechanical compatibility of blends, as evidenced by the positive deviation of shear viscosity of the rubber blend, that is, the calculated shear viscosity being higher than that of experimental data. Moreover, the pulsed NMR results indicated that the spin‐spin relaxation (T₂) of all three components of the rubber blend was compressed upon the addition of the homogenizing agent. The ratio of NR/EPDM in the blend to best resist the ozone gas is 80/20 with the addition of silica of 30 phr into the blend. Also, the NR/EPDM filled with silica had a decreased change in thermal and mechanical properties of blends after thermal aging. The synergistic effect of silica content and high NR content (80) in 20 phr EPDM could improve antioxidation by ozone in the absence of a normal antioxidant for natural rubber. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 3401–3416, 2004     

Properties and morphologies of elastomer blends modified with EPDM‐g‐poly[2‐dimethylamino ethylmethacrylate]

The graft copolymerization of 2‐dimethylamino ethylmethacrylate (DMAEMA) onto ethylene propylene diene mononer rubber (EPDM) was carried out in toluene via solution polymerization technique at 70°C, using dibenzoyl peroxide as initiator. The synthesized EPDM rubber grafted with poly[DMAEMA] (EPDM‐g‐PDMAEMA) was characterized with ¹H‐NMR spectroscopy, gel permeation chromatography (GPC), differential scanning calorimetry (DSC), and thermal gravimetric analysis (TGA). The EPDM‐g‐PDMAEMA was incorporated into EPDM/butadiene acrylonitrile rubber (EPDM/NBR) blend with different blend ratios, where the homogeneity of such blends was examined with scanning electron microscopy and DSC. The scanning electron micrographs illustrate improvement of the morphology of EPDM/NBR rubber blends as a result of incorporation of EPDM‐g‐PDMAEMA onto that blend. The DSC trace exhibits one glass transition temperature (T_g) for EPDM/NBR blend containing EPDM‐g‐PDMAEMA, indicating improvement of homogeneity. The physico‐mechanical properties after and before accelerated thermal aging of the homogeneous, and inhomogeneous EPDM/NBR vulcanizates with different blend ratios were investigated. The physico‐mechanical properties of all blend vulcanizates were improved after and before accelerated thermal aging, in presence of EPDM‐g‐PDMAEMA. Of all blend ratios under investigation EPDM/NBR (75/25) blend possesses the best physico‐mechanical properties together with the best (least) swelling (%) in brake fluid. Swelling behavior of the rubber blend vulcanizates in motor oil and toluene was also investigated. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Enhanced dielectric breakdown strength in TiO2-SiO2-Al2O3 based ceramics prepared through hot-press assisted liquid phase sintering

Linear dielectric ceramics have received much attention due to high power density, fast discharge speed and ultralow dielectric loss, which are expected as promising candidates for the pulsed power system applications. However, their relatively low dielectric breakdown strength usually cannot meet the requirements of practical application. In this work, we adopt hot-press sintering method to enhance the dielectric breakdown strength of the TiO₂-SiO₂-Al₂O₃ based ceramics, and the dielectric breakdown strength reaches 77.5 kV/mm, which is 1.8 times as large as samples prepared by conventional sintering method. The effect of different sintering methods on microstructure, dielectric properties and dielectric breakdown strength is investigated. The improvement of dielectric breakdown strength can be ascribed to improved bulk density, smaller grain size, and reduced reduction of Ti⁴⁺ to Ti³⁺, associated with the applied external pressure and lower sintering temperature. Eventually, large power density (18.20 MW/cm³) is obtained in pulse overdamped discharge circuit. Meanwhile, the stored energy is also released in a short time (about 11.3 ns to release 90% of saturated energy density value).     

Dielectric relaxation behavior and energy storage properties in Ba0.4Sr0.6Zr0.15Ti0.85O3 ceramics with glass additives

Ba_0.4Sr_0.6Zr_0.15Ti_0.85O₃ ceramics with SrO–B₂O₃–SiO₂ glass additives were prepared via the solid state reaction route. The effects of glass contents on the sintering behavior, dielectric properties, microstructures, and energy storage properties of BSZT ceramics were investigated. Dielectric breakdown strength of 22.4 kV/mm was achieved for BSZT ceramics with 20 wt% glass addition. Dielectric relaxation behavior was observed in dielectric loss versus temperature plots. In order to investigate the mechanism of dielectric breakdown performance, the relationship between dielectric breakdown strength and grain boundary barrier was studied by the measurements of breakdown strength and activation energy. A discharged energy density of 0.45 J/cm³ with an energy efficiency of 88.2% was achieved for BSZT ceramics with 5 wt% glass addition.