Study on Mechanical and Dielectric Properties of Jute Fiber Reinforced Low-Density Polyethylene (LDPE) Composites

Abstract

Jute fiber (Hessian cloth) reinforced low-density polyethylene (LDPE) composites were prepared by heat press molding techniques. The mechanical properties such as tensile strength (TS), bending strength (BS), and elongation at break of the composites were studied. The enhancement of TS (33%) and BS (50%) were obtained as a result of reinforcment jute fabrics in LDPE. In order to improve the mechanical properties and adhesion between jute and LDPE, hessian cloth were each treated with 2-hydroxyl ethyl methacrylate (HEMA). The HEMA-treated jute composite showed higher tensile and bending strength compared to untreated jute composite and LDPE. Dielectric properties like dielectric constant and loss tangent (tan δ) of jute, LDPE and composites were studied. Ferro to paraelectric phase transition occurred in both treated and untreated jute composites containing more than 20% jute. Water uptake behaviors of the composite were monitored and HEMA-treated composite showed lower water absorption behavior. The adhesion nature of jute and LDPE also characterized by scanning electronic microscopy (SEM), better adhesion was observed between HEMA-treated jute and LDPE over untreated ones.     

Fracture toughness of poly(lactic acid)/ ethylene acrylate copolymer/wood‐flour composite ternary blends

A fracture mechanics analysis based on the J‐integral method was adopted to determine the resistance of composites with various concentrations of wood‐flour and ethylene acrylate copolymer (EAC) to crack initiation (J_in) and complete fracture (J_f). The J_in and J_f energies of unmodified poly(lactic acid) (PLA)/wood‐flour composites showed the deleterious effect of incorporating wood fibers into the plastic matrix by significantly decreasing the fracture toughness of PLA as the wood‐flour content increased. The reduced fracture toughness of the matrix induced by adding brittle wood‐flour into PLA was well recovered by impact modification of the composites with EAC. Microscopic morphological studies revealed that the major mechanisms of toughening were through the EAC existing as separate domains in the bulk matrix of the composites which tended to act as stress concentrators that initiated local yielding of the matrix around crack tips and enhanced the toughness of the composites. © 2012 Society of Chemical Industry     

Tensile,flexural and impact properties of jute fibre-based thermosetting composites

Abstract

The present study reports static and impact mechanical properties of jute fibre-based thermosetting composites using woven and flat braided jute fabrics. Tensile, three-point flexural and low-to-medium energy drop-weight impact tests were conducted and mechanical properties were evaluated to study their dependence upon surface modifications of the fibre materials due to bleaching and coating treatments. Full-bleaching (longer and rigorous) treatments improved interfacial bonding and tensile strength properties of the woven jute composites compared to unbleached and half-bleached counterparts. Bleaching treatments did not seem to improve the flexural strength of composites. Unbleached (natural) jute composites have relatively better flexural strength due to reduced microstructural waviness or fibre crimping to facilitate flexural failure. With coated jute yarns, the tensile properties of the resultant flat braided composites slightly degraded, whereas the flexural properties showed clear improvements. The changes in the mechanical properties were broadly related to the accompanying modifications and to the state of microstructural imperfections, namely fibre/matrix interfacial adhesion, severity of resin matrix shrinkage during the curing process, fibre/matrix debonding and distribution of disbonds within the matrix region, and also to the relative fibre filament density along the loading axis, in the cured composite structure. There was a clear indication that natural woven jute composites could be more effective in applications requiring better impact damage resistance, energy absorption capability and improved progressive crushing behaviour.     

Effect of Ultraviolet Radiation on the Mechanical and Dielectric Properties of Hessian Cloth/PP Composites with Starch

Hessian cloth (jute fabrics) reinforced poly(propylene) (PP) composites (45 wt% fiber) were prepared by compression molding and the mechanical properties were evaluated. Jute fabrics and PP sheets were treated with UV radiation at different intensities and then composites were fabricated. It was found that mechanical properties of the irradiated jute and irradiated PP-based composites were found to increase significantly compared to that of the untreated counterparts. Irradiated jute fabrics were also treated with aqueous starch solution (1–5%, w/w) for 2–10 min. Composites made of 3% starch-treated jute fabrics (5 min soaking time) and irradiated PP showed the best mechanical properties. Tensile strength, bending strength, tensile modulus, bending modulus and impact strength of the composites were found to improve 31, 41, 42, 46 and 84% higher over untreated composites. Water uptake, thermal degradation and dielectric properties of the resulting composites were also performed.     

Effect of the consolidation degree on the fracture and failure behavior of self‐reinforced polypropylene composites as assessed by acoustic emission

In this work, the fracture and failure behavior of self‐reinforced polypropylene composites (SRPPC) was studied. As reinforcement woven fabric, whereas as matrix materials α and β crystal forms of isotactic polypropylene (PP) homopolymer and random PP copolymer (with ethylene) were used. Composite sheets were produced by a film‐stacking method and compression molded for constant holding time and at constant pressure but at different processing temperatures to obtain SRPPC sheets with different consolidation quality. The failure behavior of tensile specimens was assessed by the acoustic emission (AE) technique and the typical failure behavior was deduced for the differently consolidated composites. Both the number of AE events and the shape of the cumulative AE events versus deformation curve depend on the adhesion between phases. Correlations between the dominant failure mechanisms and AE events amplitude for model specimens were established which can be used to monitor the damage growth process in SRPPCs. POLYM. ENG. SCI., 2010. © 2010 Society of Plastics Engineers     

Effect of additives on reinforcement of radiation-induced jute-urethane polymer composites

Thick polymer film was prepared under gamma irradiation using urethane acrylate in the presence of N-vinylpyrrolidone, ethyl hexyl acrylate, and trimethylol propane triacrylate. Both jute dust and hessian cloth (jute fabric) were used to constitute composites based on the prepared resin matrix. Some of their physical and mechanical properties were studied. Some additives such as acetic acid, acrylamide, urea, talc, and titanium oxide were incorporated into the formulation to investigate their effect on the physical and mechanical properties. Water absorption and weathering resistance of the resin and composites were also investigated. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 67: 79–85, 1998     

Impact fracture behavior of continuous glass fiber-reinforced nylon 6

The impact fracture toughness of nylon 6/continuous glass fiber composites at four levels of fiber content has been studied. The composites were produced by anionically polymerizing caprolactam within a glass mat using a vacuum injection technique. Application of linear elastic fracture mechanics to characterize the impact fracture toughness of the composites, using an energy approach (G_IC), has been found to be applicable provided that a correction is made for the size of the damage zone. The concept of J_c, fracture energy per unit ligament area, has also been applied to the composites and agreement between G_IC and J_c has been found to be reasonably satisfactory. The ratio of crack propagation energy to the total energy absorbed (ductility index) has also been calculated. The ductility index was found to be close to one for the composites, indicating that additional energy is involved in propagating the fracturing cracks probably due to fiber debonding and/or crack blunting and fiber pullout. Fractographic examination of the impact fracture surface confirmed the presence of these features.     

Epoxy/p‐phenylenediamine functionalized graphene oxide composites and evaluation of their fracture toughness and tensile properties

In an attempt to enhance the mechanical properties of epoxy/graphene‐based composites, the interface was engineered through the functionalization of graphene oxide (GO) sheets with p‐phenylenediamine; this resulted in p‐phenylenediamine functionalized graphene oxide (GO–pPDA). The morphology and chemical structure of the GO–pPDA sheets were studied by spectroscopic methods, thermal analysis, X‐ray diffraction, and transmission electron microscopy. The characterization results show the successful covalent functionalization of GO sheets through the formation of amide bonds. In addition, p‐phenylenediamine were polymerized on graphene sheets to form crystalline nanospheres; this resulted in a GO/poly(p‐phenylenediamine) hybrid. The mechanical properties of the epoxy/GO–pPDA composite were assessed. Although the Young's modulus showed improvement, more significant improvements were observed in the strength, fracture strain, and plane‐strain fracture toughness. These improvements were attributed to the unique microstructure and strong interface between GO–pPDA and the epoxy matrix. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43821.     

Multilayered ceramic composites – a review

With the aim of improving the toughness of ceramic materials, laminated composites have been successfully developed since Clegg et al. (1990) inserted weak interfaces using very thin graphite layers between silicon carbide sheets and obtained a composite that exhibited non-catastrophic fracture characteristics. The weak interface must allow the crack to deviate either by deflection or delamination; in other words, the interface must exhibit a fracture resistance that is lower than that of the matrix layer. In parallel, ceramic laminated composites with strong interfaces were developed in which the residual tensile and compressive stresses appeared in alternate layers during cooling after sintering. These composites are prepared by stacking ceramic sheets produced by lamination or tape casting or by the sequential formation of layers by slip casting, centrifugation or electrophoretic deposition. The techniques may be combined to obtain a composite with the most adequate configuration. This work presents a review about the obtainment of multilayered ceramic composites as a toughening mechanism of ceramic plates.     

Mechanical properties of maleic anhydride treated jute fibre/polypropylene composites

Abstract

The effect of maleic anhydride (MA) modification of jute fibre on the mechanical properties of jute/polypropylene (PP) composites was studied. Jute fibre, an environmental friendly, low-density renewable material was chemically modified with MA before the incorporation with PP to improve interfacial adhesion between them. Fourier transform infrared (FTIR) study showed that the C=C groups of MA attached to jute cellulose reacted with the PP matrix. Jute fibre/PP composite treated with MA displayed higher Young's modulus and dynamic storage modulus owing to the enhanced interfacial adhesion between the fibre and PP matrix. A scanning electron microscopy (SEM) study showed evidence of the enhanced adhesion and bridging in the interfacial region of the composite as the result of MA modification of jute fibre.     

Impact toughness,viscoelastic behavior,and morphology of polypropylene–jute–viscose hybrid composites

In this investigation, we studied the impact toughness and viscoelastic behavior of polypropylene (PP)–jute composites. In this study, we used viscose fiber as an impact modifier and maleated PP as a compatibilizer. The toughness of the composites was studied with conventional Charpy and instrumental falling‐weight impact tests. The composites’ viscoelastic properties were studied with dynamic mechanical analysis. The results show that the incorporation of viscose fibers improved the impact strength and toughness to 134 and 65% compared to those of the PP–jute composites. The tan δ peak amplitude also increased with the addition of the impact modifier and indicated a greater degree of molecular mobility. The thermal stability of the composites was evaluated with thermogravimetric analysis. The addition of 2 wt % maleated polypropylene (MAPP) to the impact‐modified composite improved the impact strength and toughness to 144 and 93%, respectively. The fiber–matrix morphology of the fracture surface and the Fourier transform infrared spectra were also studied to ascertain the existence of the type of interfacial bonds. Microstructural analysis showed the retention of viscose fibers in the composites compared to the more separated jute fibers. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 42981.     

Effect of alkaline treatment on physical,mechanical, and thermal characteristics of jute filler reinforced epoxy composites

With burgeoning environmental concerns worldwide, using natural fibers/fillers to produce composites rather than conventional fibers is on the rise. The current work focuses on the physical and thermomechanical characteristics of alkaline-treated jute filler-based epoxy composites. The composites have been prepared with different weight fraction of jute fillers (0%, 2.5%, 5%, 7.5%, 10%, and 12.5%) using hand layup process. The X-ray diffraction and Fourier transform infrared spectroscopy analysis observed that the alkali treatment of jute fillers improved the crystallinity and molecular structure, enhancing the interfacial and molecular bond between fillers and matrix. The mechanical characterizations of developed composites analyzed that the inclusion of treated jute fillers strengthened the tensile and flexural properties. The 5% filler-based composites have demonstrated maximum tensile strength (54.06 MPa) and modulus (3.12 GPa) with maximum flexural strength (67.55 MPa) and modulus (3.90 GPa). The viscoelastic characteristics of composites revealed that the 7.5% filler-based composite has the highest storage modulus (3.75 GPa), loss modulus (0.496 GPa), and glass transition temperature (91°C) due to greater interfacial interactions of molecules. The weight loss and degradation of composites analyzed with thermogravimetric analysis, and observed better thermal stability with treated jute fillers. The morphological analysis at fracture surfaces analyzed the brittle catastrophic failure of composites. Therefore, the finding produced better specific strength and stiffness with greater thermal stability for electronics equipment, packaging, and transportation.     

Effect of flake size on thermal properties of graphene oxide/poly(methyl methacrylate) composites prepared via in situ polymerization

The effect of graphene oxide (GO) flake size on thermal properties of GO/poly(methyl methacrylate) (GO/PMMA) composites prepared via in situ polymerization was investigated. Two styles of GO sheets were synthesized from different sizes of graphite powders by modified Hummers' method and GO/PMMA composites with GO of different sizes were prepared via in situ polymerization. Transmission electron microscopy verified that GO sheets produced from large graphite powders was obviously larger than that from small graphite powders. The similar number of layers and disorder degree of two types of GO sheets were proved by X‐ray diffraction and Raman, respectively. X‐ray diffraction and scanning electron microscopy results of GO/composites proved the homogenous dispersion of both two types of GO sheets in polymer matrix. Dynamic mechanical analysis and thermogravimetric analysis results showed that large GO sheets exhibit better improvement than small GO sheets in thermal properties of the composites. Compared with neat PMMA, the glass transition temperature and decomposition temperature of the composites with large GO sheets (0.20 wt %) were increased by 15.9 and 25.9 °C, respectively. © 2018 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 46290.     

Effect of interfacial residual thermal stress on the fracture behavior of Cf/B4C composites prepared by spark plasma sintering

Carbon fiber reinforced boron carbide (Cf/B₄C) composites were fabricated with different Cfs contents by spark plasma sintering (SPS). The interfacial residual thermal stress (RTS) distribution in the Cf/B₄C composites and its effects on the fracture behavior of the composites was investigated based on Raman spectroscopy and finite-element (FE) calculation. The results show that the maximum RTS of Cf in as-produced composites were obtained at the edge of fibers. The B₄C matrix among fibers suffered a high compressive and tensile RTS simultaneously in radial and tangential directions, which caused the formation of micro-cracks and became the origin of fracture failure of the Cf/B₄C composites. The maximum relative density 98.7% and bending strength of 391.41 MPa were obtained when the Cf content was 2.5% while the maximum fracture toughness of 5.46 MPa·m^1/2 at 5% Cf content of Cf/B₄C sample. The sharp decreases of bending strength when increasing content of Cf cloth was mainly caused by high RTS in the composites.     

Preparation and properties of reduced graphene oxide/fused silica composites

An in situ strategy for fabrication of reduced graphene oxide/fused silica (rGO/FS) composites using 3-aminopropyltriethoxysilane as surfactant is reported. GO nanosheets were bound to FS particles by an electrostatic assembly between ultra thin negatively charged GO sheets and positively charged amino-modified FS particles. After spark plasma sintering, rGO/FS bulk composites have been produced from the GO and FS composite particles with GO being reduced to rGO in vacuum at high temperatures. Results show that rGO sheets were well dispersed in the matrix, and conductivity of these rGO/FS composites at room temperature was strongly dependent on the rGO nanosheet concentration. i.e., the conductivity of rGO/FS was increased to 10⁻⁴ S/cm when a conducting network was formed inside the composites. The effect of GO nanosheets on the mechanical properties of rGO/FS bulk composites was also investigated. The addition of 1 wt.% GO sheets to FS resulted in 72% increase in Vickers hardness, indicating the stress transfering from the FS matrix to the rigid rGO sheets. With the same rGO content, the fracture toughness of the as-prepared composites was increased by 74%. The main toughening mechanisms were thought to be crack deflection, crack branching, pulling-out and bridging of the rGO sheets.     

Model development for work of fracture of hybrid composites

The theoretical modeling for work of fracture of hybrid composites was investigated. Current available models for the work of fracture mostly consider single fiber composites and are not supported by experimental evidence. This is due to the complex nature of work of fracture, and presence of far too many variables for the experimental validation such as interaction of fibers with matrix and with each other. In this work, a model was developed for hybrid composites based on the modification of rule of mixtures, considering pull‐out, fracture, debonding, and stress redistribution for fibers along fracture for matrix. Later, the model was experimentally evaluated by GF‐hemp‐PP hybrid composites, and showed a better agreement in comparison to a prevalent model for work of fracture. Aside from matrix failure, the dominant failure mechanisms were fiber stress redistribution for long fiber composites and fiber pull out for short fiber composites. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44711.     

A Comparative Study on the Mechanical,Degradation and Interfacial Properties of Jute/LLDPE and Jute/Natural Rubber Composites

Jute fabric (hessian cloth) reinforced low-density polyethylene (LLDPE) composites (40 wt%) and solid natural rubber-(NR) based composites (40 wt%) were fabricated by compression molding. Tensile strength (TS), tensile modulus (TM) and percentage elongation at break (Eb) of jute/LLDPE composites were found to be 29, 680 MPa and 20%, and for jute/NR-based composites were also found to be 15, 122 MPa and 94%, respectively. Interfacial shear strength (IFSS) of the jute/LLDPE and jute/NR systems was investigated by using the single fiber fragmentation test (SFFT). Scanning electron microscopy (SEM) and aqueous degradation tests were also performed.     

Effects of alkali and silane treatment on the mechanical properties of jute‐fiber‐reinforced recycled polypropylene composites

Jute‐fibers‐reinforced thermoplastic composites are widely used in the automobile, packaging, and electronic industries because of their various advantages such as low cost, ease of recycling, and biodegradability. However, the applications of these kinds of composites are limited because of their unsatisfactory mechanical properties, which are caused by the poor interfacial compatibility between jute fibers and the thermoplastic matrix. In this work, four methods, including (i) alkali treatment, (ii) alkali and silane treatment, (iii) alkali and (maleic anhydride)‐polypropylene (MAPP) treatment, and (iv) alkali, silane, and MAPP treatment (ASMT) were used to treat jute fibers and improve the interfacial adhesion of jute‐fiber‐reinforced recycled polypropylene composites (JRPCS). The mechanical properties and impact fracture surfaces of the composites were observed, and their fracture mechanism was analyzed. The results showed that ASMT composites possessed the optimum comprehensive mechanical properties. When the weight fraction of jute fibers was 15%, the tensile strength and impact toughness were increased by 46 and 36%, respectively, compared to those of untreated composites. The strongest interfacial adhesion between jute fibers and recycled polypropylene was obtained for ASMT composites. The fracture styles of this kind of composite included fiber breakage, fiber pull‐out, and interfacial debonding. J. VINYL ADDIT. TECHNOL., 2010. © 2010 Society of Plastics Engineers.     

Improved mechanical and moisture resistance property of in situ polymerized transparent PMMA/Cellulose composites

This article evaluates the role of cellulosic fillers in a synthetic polymer matrix like polymethylmethacrylate (PMMA) when incorporated by in situ suspension polymerization technique. Cellulose micro/nanofibers (CNF) were extracted from jute fibers and chemically modified with maleic anhydride (MACNF) to increase their interfacial compatibility with PMMA by participation of the MA moiety in the free radical polymerization with MMA. The effect of incorporating MACNF on the physical and mechanical properties of the PMMA matrix was investigated. Optical transparency was retained in the in situ prepared PMMA/cellulose composites (IPMC) similar to that of unreinforced PMMA. Another set of PMMA/cellulose composites was prepared by dispersing MACNF in PMMA matrix by ex situ solution dispersion method (EPMC). The modification of CNF with MA significantly improved the filler/matrix interfacial compatibility and in situ polymerization technique further enhanced the properties of the composites. The high moisture absorption tendency, which is a major drawback of the cellulose filled composites, remarkably reduced in IPMC. POLYM. COMPOS., 36:1748–1758, 2015. © 2014 Society of Plastics Engineers     

Short-fiber-reinforced styrene–butadiene rubber composites

Processing characteristics, anistropic swelling, and mechanical properties of short-jute-fiber-and short-glass-fiber-reinforced styrene–butadiene rubber (SBR) composites have been studied both in the presence and absence of carbon black. Tensile and tear fracture surfaces of the composites have been studied using scanning electron microscopy (SEM) in order to assess the failure criteria. The effects of bonding agent. carbon black, jute fiber, and glass fiber on the fracture mode of the composites have also been studied. It has been found that jute fiber offers good reinforcement to SBR as compared to glass fibers. The poor performance of glass fibers as reinforcing agent is found to be mainly due to fiber breakage and poor bonding between fiber and rubber. Tensile strength of the fiber–SBR composites increases with the increase in fiber loading in the absence of carbon black. However, in the presence of carbon black a minimum was observed in the variation of strength against fiber loading. SEM studies indicate that fracture mode depends not on the nature of the fiber but on the adhesion between the fiber and the matrix.