Effect of BN grain size on microstructure and mechanical properties of the ZrB2–SiC–BN composites

ZrB₂–20 vol.%SiC composites containing 10 vol.% h-BN particles (ZSB) with average grain sizes ranging from 1 μm to 10 μm were hot-pressed. The fracture toughness of the ZSB composites was higher than reported results of monolithic ZrB₂ (2.3–3.5 MPa m^1/2) and SiC particle reinforced ZrB₂ composites (4.0–4.5 MPa m^1/2). The improvement in the fracture toughness of the ZSB composites was due to the high aspect ratio of h-BN and weaker interface bonding, which could enhance crack deflection and stress relaxation near the crack-tip. Compared with the flexural strength of the ZrB₂–SiC composites, the reduction in the flexural strength of the ZSB composites was attributed to the weaker interface bonding and the lower relative density. Furthermore, improvement in toughness and the reduction in the strength were valuable to improve the thermal shock resistance of the ZSB composites. The ΔT_c of ZSB5 material is 400 °C which is higher than ZrB₂–20%SiC and ZrB₂–15%SiC–5%AlN.     

Effects of high-temperature annealing on the microstructure and properties of C/SiC–ZrB2 composites

C/SiC–ZrB₂ composites prepared via precursor infiltration and pyrolysis (PIP) were treated at high temperatures ranging from 1200 °C to 1800 °C. The mass loss rate of the composites increased with increasing annealing temperature and the flexural properties of the composites increased initially and then decreased reversely. Out of the four samples, the flexural strength and the modulus of the specimen treated at 1400 °C are maximal at 216.9 MPa and 35.5 GPa, suggesting the optimal annealing temperature for mechanical properties is 1400 °C. The fiber microstructure evolution during high-temperature annealing would not cause the decrease of fiber strength, and moderate annealing temperature enhanced the thermal stress whereas weakened the interface bonding, thus boosting the mechanical properties. However, once the annealing temperature exceeded 1600 °C, element diffusion and carbothermal reduction between ZrO₂ impurity and carbon fibers led to fiber erosion and a strong interface, jeopardizing the mechanical properties of the composites. The mass loss rate and linear recession rate of composites treated at 1800 °C are merely 0.0141 g/s and 0.0161 mm/s, respectively.     

Effect of processing routes on mechanical and thermal properties of copper–graphene composites

In this paper, copper–graphene composites were fabricated by using two different processing routes (ball milling (BM) and ultrasonication) followed by spark plasma sintering. Vickers hardness and anisotropic thermal conductivity of the composites were measured and observed that ultrasonicated fabricated composites gave better result compared with BM composite and even from pure copper. The hardness values obtained for ultrasonicated copper–graphene composite were 69?HV (57% higher) and thermal conductivity 387?W/m?K (13% higher) by using only 0.5?wt-% of graphene, while for pure copper the values were 44?HV and 341?W/m?K. The value of anisotropic thermal conductivity ultrasonicated composites was also 1.97 which is much higher than pure copper 0.94.     

Effect of Cu/Zn on microstructure and mechanical properties of extruded Mg–Sn alloys

In this paper, the effect of Cu and Zn addition on mechanical properties of indirectly extruded Mg–2Sn alloy was investigated. Mg–2Sn–0.5Cu alloy exhibits a moderate yield strength (YS) of 225?MPa and an ultimate strength of 260?MPa, which are much higher than those of the binary Mg–2Sn alloy, and the elongation (EL) evolves as ～15.5%. Mechanical properties of the Mg–2Sn–0.5Cu alloy are deteriorated with more 3 wt-% Zn addition, and YS and EL are reduced as 160?MPa and ～10%. The detailed mechanism is discussed according to the work-hardening rate and strengthening effect related to the grain sizes, second phases and macro-textures. Grain refinement and proper texture are believed to play a critical role in both strength and ductility optimisation.     

Microstructures and mechanical properties of spark plasma sintered Cu–Cr composites prepared by mechanical milling and alloying

Nanograined Cu–8 at.% Cr composite was produced by a combination of mechanical milling (MM), mechanical alloying (MA) and spark plasma sintering (SPS). Commercial Cu and Cr powders were pre-milled separately by MM. The milled Cu and Cr powders were then mechanically alloyed with as-received Cr and Cu powders respectively. After milling, the powder mixtures were separately subjected to SPS. It was found that pre-milling Cr can efficiently decrease the size of grain and reinforcement, resulting in remarkable strengthening. The grain size of Cu matrix was about 82 nm after SPS. The Vickers hardness, compressive yield strength and compression ratio of the composite were 327 HV, 1049 MPa and 10.4%, respectively. The excellent mechanical properties were primarily attributed to dispersion strengthening of the Cr particles and fine grain strengthening of the Cu matrix. The strong Cu/Cr interface and dissolved Cr atoms can also contribute to strengthening of the composite.     

Investigation of microstructure and mechanical properties of steel fibre–cast iron composites

Abstract

The aim of the present experimental study was to investigate improvement of the toughness and strength of grey cast iron by reinforcing with steel fibres. The carbon content of the steel fibres was chosen to be sufficiently low that graphite flakes behaving as cracks were removed by carbon diffusion from the cast iron to the steel fibres during the solidification and cooling stages. To produce a graphite free matrix, steel fibres with optimum carbon content were used and the reinforced composite structure was cast under controlled casting conditions and fibre orientation. Three point bend test specimens were manufactured from steel fibre reinforced and unreinforced flake graphite cast iron and then normalising heat treatments were applied to the specimens at temperatures of 800 and 850°C. The fracture toughness and strength properties of the steel fibre reinforced material were found to be much better than those of unreinforced cast iron. The microstructures of the composite at the fibre–matrix transition zone were examined.     

Effect of β heat treatment temperature on microstructure and mechanical properties of in situ titanium matrix composites

TiB and La₂O₃ reinforced titanium matrix composites were in situ prepared by casting and hot working. An effort was made to investigate relationship between β heat treatment temperature, microstructure and mechanical properties. Tensile tests were performed at room temperature, 600, 650 and 700 °C, respectively. Results indicated that composites treated at 10 °C above β transus points obtained fine grain microstructures and superior mechanical properties. When composites were treated at 20 °C above β transus points, the larger α colonies sizes led extremely decreased strength and the effect of reinforcements’ volume fraction on matrix of composites was reduced; dominant failure modes at high temperatures also differed from the fine microstructure.     

Effect of Al and C on structure and mechanical properties of Fe–Al–C alloys

Abstract

Effect of aluminium and carbon content on the microstructure and mechanical properties of Fe–Al–C alloys has been investigated. Alloys were prepared by combination of air induction melting with flux cover (AIMFC) and electroslag remelting (ESR). The ESR ingots were hot forged and hot rolled at 1373 K. As rolled alloys were examined using optical microscopy, scanning electron microscopy (SEM) and transmission electron microscopy (TEM) to understand the microstructure of these alloys. The ternary Fe–Al–C alloys containing 10·5 and 13 wt-%Al showed the presence of three phases: FeAl with disordered bcc structure, Fe₃Al with ordered DO₃ structure and Fe₃AlC_0·5 precipitates with L′1₂ structure. Addition of high concentration of carbon to these alloys resulted in excellent hot workability and superior tensile at room temperature as well as tensile and creep properties at 873 K. An increase in Al content from 9 to 13 wt-% in Fe–Al–C alloys containing the same levels of carbon has no significant influence on strength and creep properties at 873 K, however resulted in significant improvement in room temperature strength accompanied by a reduction in room temperature ductility.     

Effect of heat treatment on microstructure and mechanical properties of Cr–Ni–Mo–Nb steel

Abstract

The microstructure and mechanical properties of a medium carbon Cr–Ni–Mo–Nb steel in quenched and tempered conditions were investigated using transmission electron microscopy (TEM), X-ray analysis, and tensile and impact tests. Results showed that increasing austenitisation temperature gave rise to an increase in the tensile strength due to more complete dissolution of primary carbides during austenitisation at high temperatures. The austenite grains were fine when the austenitisation temperature was <1373 K owing to the pinning effect of undissolved Nb(C,N) particles. A tensile strength of 1600 MPa was kept at tempering temperatures up to 848 K, while the peak impact toughness was attained at 913 K tempering, as a result of the replacement of coarse Fe rich M₃C carbides by fine Mo rich M₂C carbides. Austenitisation at 1323 K followed by 913 K tempering could result in a combination of high strength and good toughness for the Cr–Ni–Mo–Nb steel.     

Microstructure and mechanical properties of Lead-free Sn–Cu solder composites prepared by rapid directional solidification

In wave soldering Sn-Cu alloy was recommended as a promising substitute of traditional Sn–Pb alloy. Here a rapid directional solidification process was firstly adopted to prepare directionally-solidified hypereutectic Sn–Cu composites. The corresponding microstructure exhibits regular lamellar structures with alterative Sn-rich phase and intermetallic compounds. The large kinetic undercooling arising from the rapid solidification condition is the inherent mechanism to obtain directionally-solidified lamellar structures for the hypereutectic Sn–Cu solder. Additionally, the measured compressive mechanical properties of the directionally solidified solder exhibit anisotropic characteristics, that is, the compressive strength along the longitudinal direction is 1.63 times higher than that along the transverse direction.     

Effect of nitrile-functionalization and thermal cross-linking on the dielectric and mechanical properties of PEN/CNTs–CN composites

In this study, a novel series of composite films consisting of nitrile-functionalized carbon nanotubes (CNTs–CN) and poly(arylene ether nitriles) (PEN) were successfully fabricated by the tape-casting method. The –CN groups in PEN chains and the phthalonitrile groups on CNTs–CN formed the thermally stable triazine rings by thermal cross-linking reaction in the presence of diamino diphenyl sulfone, which was characterized by Fourier transform infrared spectroscopy. The result indicated that the chemical cross-linking reaction occurred accompanied by the emergence of a new absorption peak at 1,361 cm^?1. Besides, the effect of cross-linking on the morphology, thermal stability, mechanical and dielectric properties of the PEN/CNTs–CN was investigated. The SEM images showed that the phase interface between surface modified CNTs and PEN matrix was indistinct, and the surface modified CNTs presented a better dispersion behavior in PEN matrix. The mechanical properties of the processed films were improved substantially compared with the unprocessed films. Furthermore, the glass-transition temperature (T _g ) of composite films processed at 320 °C for 4 h (about 245 °C) was higher than that of composite films before thermal treatment (about 205 °C). The 5 % weight loss temperature of the composite films (processed at 320 °C for 4 h) increased by about 110 °C compared with the composite films (unprocessed). More importantly, by thermal cross-linking, the dielectric constant (ε) of composite films with 8 wt% CNTs–CN loading was increased from 31.8 to 33.9, and dielectric loss (tan δ) was decreased from 0.90 to 0.61 at 1 kHz.     

Effect of flame retardants on mechanical properties,flammability and foamability of PP/wood–fiber composites

The mechanical properties, flame retardancy, thermal degradation and foaming properties of wood–fiber/PP composites have been investigated. Ammonium polyphosphate (APP) and silica were used as flame retardants. The limiting oxygen index (LOI), thermal gravimetric analysis (TGA) and cone colorimeter (CONE) were employed for the study of fire retardance. At the same time, wood–fiber/PP composite foams were produced with the batch foaming technique using CO₂ as blowing agent. The effects of APP and silica content, pressure and temperature on the final cell structure were investigated. According to LOI, TGA and cone calorimeter results obtained from the experiments, APP and silica are effective flame retardants for wood–fiber/PP composites, and silica was shown to have a flame retardant synergistic effect with APP in wood–fiber/PP composite. The mechanical properties of the composites decreased with addition of flame retardants, except for the tensile strength of small amount of silica filled wood–fiber/PP composite. The results also revealed that the cellular morphologies of the foamed wood–fiber/PP composites are a strong function of the content of APP and silica as well as foaming conditions.     

Effect of surface modification and hybridization on dynamic mechanical properties of Roystonea regia/glass–epoxy composites

The paper evaluates effect of fibre surface modification and hybridization on dynamic mechanical properties of Roystonea regia/epoxy composites. Surface modification involved alkali and silane treatments. Alkali treatment proved to be more effective on dynamic mechanical properties as compared to silane treatment. Storage and loss modulus values increased after treatments with simultaneous decrease in tan δ values. Roystonea regia and glass fibres were used together with varying proportions as reinforcement in epoxy matrix to study the hybridization effect on dynamic mechanical properties. Storage and loss modulus values increased with increase in glass fibre content whereas tan δ values were found to decrease. Scanning electron microscopy of tensile fractured surfaces was carried out to study the interface adhesion of different composites.     

Effects of rare earth La on microstructure and properties of Ag–21Cu–25Sn alloy ribbon prepared by melt spinning

Ag–21Cu–25Sn alloy ribbon as a promising intermediate temperature alloy solder (400–600 °C) was prepared by melt spinning technique in this paper. Rare earth La was added into Ag–21Cu–25Sn alloy to refine the microstructures and improve the wettabilities of as-prepared alloy solders. The phase constitutions, microstructures, melting temperatures and wettabilities of selected specimens were respectively tested. The results showed that the dominant phase constitutions of Ag–21Cu–25Sn–xLa alloy ribbons were Ag₃Sn and Cu₃Sn. The grain size of Ag–21Cu–25Sn–xLa alloy decreased with the addition of La increasing. La addition reduced the melting temperatures of Ag–21Cu–25Sn–xLa alloy ribbons, and effectively improved the wettabilities of the alloy ribbons. When the addition of La was 0.5 wt%, the wettability of as-prepared alloy solder achieved the optimal value of 158 cm² g⁻¹ under brazing temperature 600 °C and dwell time 15 min. In addition, raising brazing temperature and prolonging dwell time could improve the wettability of Ag–21Cu–25Sn–xLa alloy ribbon.     

Effect of hot isostatic pressing on mechanical properties and microstructure of 70–30 cupronickel castings

Abstract

The present work is part of an investigation into the use of hot isostatic pressing to recover 70–30 cupronickel castings. These alloys have particularly good corrosion resistance and, when strengthened with silicon and chromium, produce a material capable of use in very severe conditions of stress and massive corrosion. However, it is not possible to recover such castings by the application of repair welding, because of the possibility of reduced corrosion resistance in the vicinity of the weld. Hot isostatic pressing represents an alternative method of casting recovery. The results reported in the present work refer to the effect of hot isostatic pressing on mechanical properties, microstructure, and the level of segregation in the alloys. Hot isostatic pressing may be used to remove casting defects in the form of fine pores up to total porosity of 5%. However, in cases where porosity takes the form of very large defects, the mechanical properties of the recovered region are inferior to those of the originally sound material. This effect is probably associated with the presence of very finely distributed oxide particles in the originally defective parts of the casting. The optimum hot isostatic pressing temperature for the best overall combination of properties was 950°C.

MST/1732     

Effect of matrix strength on the mechanical properties of Al–Zn–Mg/SiCP composites

The mechanical properties of Al–Zn–Mg alloy reinforced with SiC_P composites prepared by solidification route were studied by altering the matrix strength with different heat treatments. With respect to the control alloy, the composites have shown similar ageing behaviour in terms of microhardness data at 135°C. It was shown that although composites exhibited enhanced modulus values, the strengthening was found to be dependent on the damage that is occurring during straining. Thus the initial matrix strength plays an important role in determining the strengthening. Consequently, compression data had shown a different trend compared to tension.     

Effect of multicomponent modifier on microstructure and mechanical properties of high Ni–Cr–Mo cast iron

Abstract

The microstructure and mechanical properties of high Ni–Cr–Mo indefinite chilled cast iron with the addition of a newly developed multicomponent modifier consisting of mixed rare earths, Si–Ca alloy and Bi–Sb alloy have been investigated through optical microscopy, X-ray diffraction and scanning electron microscopy, along with hardness, impact toughness and wear resistance measurements. After the addition of the modifier, the grain sizes of the primary austenite and eutectic carbides are found to be greatly refined, and the typically highly continuous net-like carbides become less interconnected but rather appear more blocky shaped. Such microstructure changes lead to mechanical property improvement in the cast specimen, with its hardness increased from 43 to 50 HRC, impact toughness from 6·3 to 7·8 J cm^?2 and ?20% increase in abrasive wear resistance.     

Effect of predeformation on microstructure and mechanical properties of Al–Cu–Li–Zr alloy containing Sc

Abstract

The effects of prior cold deformation on the microstructures and the room temperature mechanical properties of an Al–3·5Cu–1·5Li–0·22(Sc + Zr) alloy have been observed by using TEM and tensile test at room temperature. The results show that the alloy has the character of aging hardening, and the major phase of precipitation and strengthening is T₁ phase. The result also show that prior cold deformation leads to more dispersive and uniform distribution of T₁ precipitations. It accelerates aging response, causes earlier aging peak occurrence, and enhances strength greatly. However, the plasticity of the alloy is declined with prior cold deformation. In contrast, excessive prior cold deformation causes coarsening and heterogeneous distribution of T₁ phase. It also reduces the strength of the alloy, therefore, influences the composite properties of the alloy. The favourable prior cold deformation is about 3·5% under the experimental condition.     

Effect of amino functionalized MWCNT on the crosslink density,fracture toughness of epoxy and mechanical properties of carbon–epoxy composites

Amino functionalized multiwalled carbon nanotubes (A-MWCNTs) reinforced two phase (A-MWNT–epoxy) and three phase (A-MWCNTs–carbon fiber–epoxy) nanocomposites were fabricated with 0.25 wt%, 0.5 wt% and 1.0 wt% loadings of A-MWCNTs. It is observed that, A-MWCNTs can improve the crosslink density of epoxy significantly. Fracture toughness of epoxy matrix is found to increase up to an optimum crosslink density improvement, indicating the role of crosslink density in imparting toughness to epoxy apart from the crack deflection contributions of A-MWCNTs. In addition to that, this study infers that, tensile, flexural properties of the three phase composites are strongly influenced by the fracture toughness changes of the matrices. This study, thus proposes additional mechanisms of toughness enhancements for two phase and mechanical properties enhancements for three phase composites imparted by A-MWCNTs.