相关Rician衰落信道下紧凑MIMO系统的容量分析

研究了Rician衰落信道下采用紧凑型双偶极子阵列的MIMO系统容量,建立了相关Rician衰落信道下紧凑MIMO系统的模型,深入分析了天线互耦、空间相关性、功率分配方案以及信道衰落环境对信道容量的影响。数值结果表明天线间距较小时,互耦和相关性会导致信道容量的损失,而在某些情况下互耦和相关性的影响会使信道容量有所增加。     

一种分布式多入多出(MIMO)信道的容量研究

分布式MIMO系统结合了点对点MIMO信道与分布式天线系统两者的特点，能改善链路的质量，提高覆盖面积。本文提出了一种包含路径损耗、阴影衰落与小尺度衰落的分布式MIMO信道模型，分析推导了采用该模型时的分布式MIMO信道容量。通过计算机仿真，研究分析了阴影衰落、Rice信道因子K等因素对分布式MIMO上行信道容量的影响，得出了分布式MIMO信道容量空间分布的特点。     

信道状态信息未知和已知的MIMO无线信道容量比较与分析

介绍了无线MIMO系统信道容量的计算方法,重点分析和比较在瑞利衰落信道下,发射端已知和未知信道状态信息时的信道容量特性,并利用Matlab对其进行仿真。仿真结果表明：在低信噪比时,采用自适应功率分配得到的信道容量特性要优于采用平均功率分配得到的信道容量特性。这种优势随着天线数目的增加而逐渐增大,但随着信噪比的增大而逐渐减小。     

频率选择性衰落MIMO信道容量分析

随着传输速率越来越高,信号所占用的带宽越来越宽,实际信道呈现出频率选择性衰落特性.根据频率选择性衰落信道特性,建立了频率选择性衰落MIMO信道模型,采用频域和时域的方法研究了在频率选择性衰落下,发射端已知和未知信道状态信息的MIMO信道容量,并给出了相关的仿真结果.研究结果表明:在相同发射功率和传输带宽下,MIMO系统可以不牺牲信号带宽而显著提高信道的容量,并且天线数量和输入信噪比的大小对信道容量具有不同的影响.研究结果为如何提高频率选择性衰落环境下MIMO信道容量提供了依据.     

基于空间信道模型的MIMO系统建模与仿真

研究了基于空间信道模型(SCM)的空域相关矩阵,搭建了MIMO通信信道仿真平台,同时考虑时延扩散、多普勒效应、波达方向及角度扩散等多种信道参数,通过蒙特卡罗方法计算了MIMO系统的信道容量、空时相关性、衰落特性及功率延迟分布特性.指出了在信道的去极化作用下,无线通信系统的多径衰落可以采用极化分集和天线分集等技术进行克服,平均入射角对系统性能起着关键的作用.     

机舱内分布式MIMO系统信道容量分析

采用自主搭建的信道测量平台测得了机舱环境下分布式MIMO系统的信道冲击响应矩阵。根据实测的信道矩阵分别计算了4种具有不同收发天线数目的分布式MIMO系统的信道容量。为了便于比较,SISO系统的信道容量也通过实测数据进行了计算。计算结果表明：在机舱环境下,采用分布式MIMO系统和采用SISO系统相比能够显著提高系统信道容量,说明分布式MIMO系统可以充分满足未来机舱内无线通信高速率数据传输的需求。     

信道容量研究与信道状态对误码率的影响

随着移动通信的发展,频谱资源短缺,通信容量不足的问题越来越明显。因此提高频谱利用率,提高信道容量显得至关重要。信道容量也是下一代移动通信中重要的研究内容之一。现代移动通信系统均采用多输入多输出系统(MIMO),文中首先在MIMO系统原理和系统模型的基础上介绍了信道特征值分析方法。然后给出了MIMO信道容量公式,并分析了在信道状态信息(CSI)未知和CSI已知这两种情况下的信道容量。对MIMO信道容量进行仿真,验证了天线数目和平均信噪比对信道容量的影响,通过仿真对比了注水功率分配算法和平均功率分配算法的信道容量,并探究了信道状态对误码率的影响。     

室内MIMO系统采用极化分集时的信道容量

典型的室内传播信道为莱斯衰落信道,可将其分解为LOS传播信道和散射信道.本文假设散射信道为瑞利衰落信道,并根据天线的极化特性,给出了存在极化分集时的LOS传播信道.基于此,本文提出了室内MIMO系统采用极化分集时的信道模型.研究表明:极化分集可以有效提高MIMO信道容量.     

基于分布式MIMO矿井无线通信系统的研究

针对矿井巷道的特殊环境以及无线通信问题,通过MIMO系统和分布式天线系统,建立了井下分布式MIMO信道模型。仿真结果表明,分布式MIMO系统具有更高的信道容量。基于分布式天线的灵活设置,分布式MIMO系统既提高了频谱利用率又减少了信号盲区,最终扩大了井下信号覆盖范围,提高了整个系统的信道容量。     

MIMO系统和无线信道容量研究

MIMO(Multiple-Input Multiple-Output)理论试图在Shannon信道容量公式基础上导出正比于收发信天线数的MIMO无线信道容量(wCC)公式.由于MIMO系统同时使用多根天线发送同频信号,在MIMO的物理信道中会包含多个虚拟独立瑞利衰落信道.因此MIMO理论关于独立瑞利衰落信道的定义在实...     

Resolution Enhancement Technology:Integrated Process Solutions using OPC

DUV lithography, using the 248 nm wavelength, is a viable manufacturing option for devices with features at 130 nm and less. Given the low kl value of the lithography, integrated process development is a necessary method for achieving acceptable process latitude. The application of assist features for rule based OPC requires the simultaneous optimization of the mask, illumination optics and the resist.Described in this paper are the details involved in optimizing each of these aspects for line and space imaging.A reference pitch is first chosen to determine how the optics will be set. The ideal sigma setting is determined by a simple geometrically derived expression. The inner and outer machine settings are determined, in turn,with the simulation of a figure of merit. The maximum value of the response surface of this FOM occurs at the optimal sigma settings. Experimental confirmation of this is shown in the paper.Assist features are used to modify the aerial image of the more isolated images on the mask. The effect that the diffraction of the scattering bars (SBs) has on the image intensity distribution is explained. Rules for determining the size and placement of SBs are also given.Resist is optimized for use with off-axis illumination and assist features. A general explanation of the material' s effect is discussed along with the affect on the through-pitch bias. The paper culminates with the showing of the lithographic results from the fully optimized system.     

Cost-effective test solutions for smart card and other integrated flash applications

From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.     

Theoretical analysis of the relationship between the Brillouin gain coefficient and the strain in the optical-fiber sensors

The relation between the power of the Brillouin signal and the strain is one of the bases of the distributed fiber sensors of temperature and strain. The coefficient of the Bfillouin gain can be changed by the temperature and the strain that will affect the power of the Brillouin scattering. The relation between the change of the Brillouin gain coefficient and the strain is thought to be linear by many researchers. However, it is not always linear based on the theoretical analysis and numerical simulation. Therefore, errors will be caused if the relation between the change of the Brillouin gain coefficient and the strain is regarded as to be linear approximately for measuring the temperature and the strain. For this reason, the influence of the parameters on the Brillouin gain coefficient is proposed through theoretical analysis and numerical simulation.     

An improved parallel thinning algorithm with two subiterations

The parallel thinning algorithm with two subiterations is improved in this paper. By analyzing the notions of connected components and passes, a conclusion is drawn that the number of passes and the number of eight-connected components are equal. Then the expression of the number of eight-connected components is obtained which replaces the old one in the algorithm. And a reserving condition is proposed by experiments, which alleviates the excess deletion where a diagonal line and a beeline intersect. The experimental results demonstrate that the thinned curve is almost located in the middle of the original curve connectivelv with single pixel width and the processing speed is high.     

Novel fiber-optical interferometer with miniaturized probe for in-hole measurements

Today, micro-system technology and the development of new MEMS （Micro-Electro-Mechanical Systems） are emerging rapidly. In order for this development to become a success in the long run, measurement systems have to ensure product quality. Most often, MEMS have to be tested by means of functionality or destructive tests. One reason for this is that there are no suitable systems or sensing probes available which can be used for the measurement of quasi inaccessible features like small holes or cavities. We present a measurement system that could be used for these kinds of measurements. The system combines a fiber optical, miniaturized sensing probe with low-coherence interferometry, so that absolute distance measurements with nanometer accuracy are possible.     

Study of waveguide coupling efficiency in hybrid silicon lasers

This paper presents a new method to increase the waveguide coupling efficiency in hybrid silicon lasers. We find that the propagation constant of the InGaAsP emitting layer can be equal to that of the Si resonant layer through improving the design size of the InP waveguide. The coupling power achieves 42% of the total power in the hybrid lasers when the thickness of the bonding layer is 100 nm. Our result is very close to 50% of the total power reported by Intel when the thickness of the thin bonding layer is less than 5 nm. Therefore, our invariable coupling power technique is simpler than Intel＇s.     

Teleportation of an arbitrary unknown N-qubit entangled state under the controlling of M controllers

A new quantum protocol to teleport an arbitrary unknown N-qubit entangled state from a sender to a fixed receiver under M controllers(M < N) is proposed. The quantum resources required are M non-maximally entangled Greenberger-Home-Zeilinger (GHZ) state and N-M non-maximally entangled Einstein-Podolsky-Rosen (EPR) pairs. The sender performs N generalized Bell-state measurements on the 2N particles. Controllers take M single-particle measurement along x-axis, and the receiver needs to introduce one auxiliary two-level particle to extract quantum information probabilistically with the fidelity unit if controllers cooperate with it.     

Diode-end-pumped Nd:YVO4/LBO lasers with 4.2W continuous-wave output at 457 nm

A continuous-wave (CW) 457 nm blue laser operating at the power of 4.2 W is demonstrated by using a fiber coupled laser diode module pumped Nd: YVO4 and using LBO as the intra-cavity SHG crystal With the optimization of laser cavity and crystal parameters, the laser operates at a very high efficiency. When the pumping power is about 31 W, the output at 457nm reaches 4.2 W, and the optical to optical conversion efficiency is about 13.5% accordingly. The stability of the out putpower is better than 1.2% for 8 h continuously working.     

A rigorous proof of MIMO channel capacity’s increase with antenna number

It is well known that adding more antennas at the transmitter or at the receiver may offer larger channel capacity in the multiple-input multiple-output（MIMO） communication systems. In this letter, a simple proof is presented for the fact that the channel capacity increases with an increase in the number of receiving antennas. The proof is based on the famous capacity formula of Foschini and Gans with matrix theory.     

Call for Papers

正Wireless Body-area Networks The last decade has witnessed the convergence of three giant worlds:electronics,computer science and telecommunications.The next decade should follow this convergence in most of our activities with the generalization of sensor networks.In particular with the progress in medicine,people live longer and the aging of population will push the development of wireless personal networks