Toughening and compatibilization of polypropylene/polyamide‐6 blends with a maleated–grafted ethylene‐co‐vinyl acetate

In this article, maleated–grafted ethylene‐co‐vinyl acetate (EVA‐g‐MA) was used as the interfacial modifier for polypropylene/polyamide‐6 (PP/PA6) blends, and effects of its concentration on the mechanical properties and the morphology of blends were investigated. It was found that the addition of EVA‐g‐MA improved the compatibility between PP and PA6 and resulted in a finer dispersion of dispersed PA6 phase. In comparison with uncompatibilized PP/PA6 blend, a significant reduction in the size of dispersed PA6 domain was observed. Toluene‐etched micrographs confirmed the formation of interfacial copolymers. Mechanical measurement revealed that the addition of EVA‐g‐MA markedly improved the impact toughness of PP/PA6 blend. Fractograph micrographs revealed that matrix shear yielding began to occur when EVA‐g‐MA concentration was increased upto 18 wt %. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 99:3300–3307, 2006     

Blends of poly(2,6‐dimethyl‐1,4‐phenylene oxide)/polyamide 6 toughened by maleated polystyrene‐based copolymers: Mechanical properties,morphology, and rheology

Poly(2,6‐dimethyl‐1,4‐phenylene oxide)/polyamide 6 (PPO/PA6 30/70) blends were impact modified by addition of three kinds of maleated polystyrene‐based copolymers, i.e., maleated styrene‐ethylene‐butylene‐styrene copolymer (SEBS‐g‐MA), maleated methyl methacrylate‐butadiene‐styrene copolymer (MBS‐g‐MA), and maleated acrylonitrile‐butadiene‐styrene copolymer (ABS‐g‐MA). The mechanical properties, morphology and rheological behavior of the impact modified PPO/PA6 blends were investigated. The selective location of the maleated copolymers in one phase or at interface accounted for the different toughening effects of the maleated copolymer, which is closely related to their molecular structure and composition. SEBS‐g‐MA was uniformly dispersed in PPO phase and greatly toughened PPO/PA6 blends even at low temperature. MBS‐g‐MA particles were mainly dispersed in the PA6 phase and around the PPO phase, resulting in a significant enhancement of the notched Izod impact strength of PPO/PA6 blends from 45 J/m to 281 J/m at the MBS‐g‐MA content of 20 phr. In comparison, the ABS‐g‐MA was mainly dispersed in PA6 phase without much influencing the original mechanical properties of the PPO/PA6 blend. The different molecule structure and selective location of the maleated copolymers in the blends were reflected by the change of rheological behavior as well. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Study on the microstructures and mechanical behaviour of compatibilized polypropylene/polyamide‐6 blends

A series of blends of polypropylene (PP)–polyamide‐6 (PA6) with either reactive polyethylene–octene elastomer (POE) grafted with maleic anhydride (POE‐g‐MA) or with maleated PP (PP‐g‐MA) as compatibilizers were prepared. The microstructures and mechanical properties of the blends were investigated by means of tensile and impact testing and by scanning electron microscopy and transmission electron microscopy. The results indicated that the miscibility of PP–PA6 blends was improved with the addition of POE‐g‐MA and PP‐g‐MA. For the PP/PA6/POE‐g‐MA system, an elastic interfacial POE layer was formed around PA6 particles and the dispersed POE phases were also observed in the PP matrix. Its Izod impact strength was four times that of pure PP matrix, whilst the tensile strength and Young's modulus were almost unchanged. The greatest tensile strength was obtained for PP/PA6/PP‐g‐MA blend, but its Izod impact strength was reduced in comparison with the pure PP matrix. © 2002 Society of Chemical Industry     

Synthesis and properties of reactively compatibilized polyester and polyamide blends

The functionalization of poly(butylene terephthalate) (PBT) has been accomplished in a twin screw extruder by grafting maleic anhydride (MA) using a free radical polymerization technique. The resulting PBT‐g‐MA was successfully used as a compatibilizer for the binary blends of polyester (PBT) and polyamide (PA66). Enhanced mechanical properties were achieved for the blend containing a small amount (as low as 2.5 %) of PBT‐g‐MA compared to the binary blend of unmodified PBT with PA66. Loss and storage moduli for blends containing compatibilizer were higher than those of uncompatibilized blends or their respective polymers. The grafting and compatibilization reactions were confirmed using FTIR and ¹³C NMR spectroscopy. The properties of these blends were studied in detail by varying the amount of compatibilizer, and the improved mechanical behaviour was correlated with the morphology with the help of scanning electron microscopy. Morphology studies also revealed the interfacial interaction in the blend containing grafted PBT. The improvement in the properties of these blends can be attributed to the effective interaction of grafted maleic anhydride groups with the amino group in PA66. The results indicate that PBT‐g‐MA acts as an effective compatibilizer for the immiscible blends of PBT and PA66. © 2000 Society of Chemical Industry     

Preparation of the HIPS/MA graft copolymer and its compatibilization in HIPS/PA1010 blends

The graft copolymer of high‐impact polystyrene (HIPS) grafted with maleic anhydride (MA) (HIPS‐g‐MA) was prepared with melt mixing in the presence of a free‐radical initiator. The grafting reaction was confirmed by infrared analyses, and the amount of MA grafted on HIPS was evaluated by a titration method. 1–5% of MA can be grafted on HIPS. HIPS‐g‐MA is miscible with HIPS. Its anhydride group can react with polyamide 1010 (PA1010) during melt mixing of the two components. The compatibility of HIPS‐g‐MA in the HIPS/PA1010 blends was evident. Evidence of reactions in the blends was confirmed in the morphology and mechanical behavior of the blends. A significant reduction in domain size was observed because of the compatibilization of HIPS‐g‐MA in the blends of HIPS and PA1010. The tensile mechanical properties of the prepared blends were investigated, and the fracture surfaces of the blends were examined by means of the scanning electron microscope. The improved adhesion in a 15% HIPS/75% PA1010 blend with 10% HIPS‐g‐MA copolymer was detected. The morphology of fibrillar ligaments formed by PA1010 connecting HIPS particles was observed. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 71: 2017–2025, 1999     

Compatibilizer in waste tire powder and low‐density polyethylene blends and the blends modified asphalt

With the increasing ratio of waste tire powder (WTP) to low‐density polyethylene (LDPE), the hardness and tensile strength of the WTP/LDPE blends decreased while the elongation at break increased. Five kinds of compatibilizers, such as maleic anhydride‐grafted polyethylene (PE‐g‐MA), maleic anhydride‐grafted ethylene‐octene copolymer (POE‐g‐MA), maleic anhydride‐grafted linear LDPE, maleic anhydride‐grafted ethylene vinyl‐acetate copolymer, and maleic anhydride‐grafted styrene‐ethylene‐butylene‐styrene, were incorporated to prepare WTP/LDPE blends, respectively. PE‐g‐MA and POE‐g‐MA reinforced the tensile stress and toughness of the blends. The toughness value of POE‐g‐MA incorporating blends was the highest, reached to 2032.3 MJ/m³, while that of the control was only 1402.9 MJ/m³. Therefore, POE‐g‐MA was selected as asphalt modifier. The toughness value reached to the highest level when the content of POE‐g‐MA was about 8%. Besides that the softening point of the modified asphalt would be higher than 60°C, whereas the content of WTP/LDPE blend was more than 5%, and the blends were mixed by stirring under the shearing speed of 3000 rpm for 20 min. Especially, when the blend content was 8.5%, the softening point arrived at 82°C, contributing to asphalt strength and elastic properties in a wide range of temperature. In addition, the swelling property of POE‐g‐MA/WTP/LDPE blend was better than that of the other compalibitizers, which indicated that POE‐g‐MA /WTP/LDPE blend was much compatible with asphalt. Also, the excellent compatibility would result in the good mechanical and processing properties of the modified asphalt. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Effects of fillers,maleated ethylene propylene diene diene rubber,and maleated ethylene octene copolymer on phase morphology and oil resistance in natural rubber/nitrile rubber blends

The phase morphology and oil resistance of 20/80 NR/NBR blends filled with different types of fillers and copolymers were investigated. In the case of filler effect, N220, N330, and N660 carbon blacks with different particle sizes were used. Additionally, the blends filled with nonblack‐reinforcing fillers, that is, precipitated and silane‐treated silica, were investigated. To study the compatibilization effect, maleated ethylene propylene diene rubber (EPDM‐g‐MA) and maleated ethylene octene copolymer (EOR‐g‐MA) were added to the blends. The results revealed that the addition of filler, either carbon black or silica, to the blend caused a drastic decrease in NR dispersed phase size. Carbon blacks with different particle sizes did not produce any significant difference in NR dispersed phase size under the optical microscope. Silica‐filled blends showed lower resistance to oil than did the carbon black–filled blends. In addition, it was determined that neither EOR‐g‐MA nor EPDM‐g‐MA could act as a compatibilizer for the blend system studied. The oil resistance of the blends with EPDM‐g‐MA is strongly affected by the overall polarity of the blend. In the case of EOR‐g‐MA, the oil resistance of the blends is significantly governed by both overall polarity of the blend and phase morphology. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 1156–1162, 2003     

Effect of core‐shell morphology evolution on the rheology,crystallization, and mechanical properties of PA6/EPDM‐g‐MA/HDPE ternary blend

In this article, polyamide 6 (PA6), maleic anhydride grafted ethylene‐propylene‐diene monomer (EPDM‐g‐MA), high‐density polyethylene (HDPE) were simultaneously added into an internal mixer to melt‐mixing for different periods. The relationship between morphology and rheological behaviors, crystallization, mechanical properties of PA6/EPDM‐g‐MA/HDPE blends were studied. The phase morphology observation revealed that PA6/EPDM‐g‐MA/HDPE (70/15/15 wt %) blend is constituted from PA6 matrix in which is dispersed core‐shell droplets of HDPE core encapsulated by EPDM‐g‐MA phase and indicated that the mixing time played a crucial role on the evolution of the core‐shell morphology. Rheological measurement manifested that the complex viscosity and storage modulus of ternary blends were notable higher than the pure polymer blends and binary blends which ascribed different phase morphology. Moreover, the maximum notched impact strength of PA6/EPDM‐g‐MA/HDPE blend was 80.7 KJ/m² and this value was 10–11 times higher than that of pure PA6. Particularly, differential scanning calorimetry results indicated that the bulk crystallization temperature of HDPE (114.6°C) was partly weakened and a new crystallization peak appeared at a lower temperature of around 102.2°C as a result of co‐crystal of HDPE and EPDM‐g‐MA. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Reactive Compatibilizer Precursors for LDPE/PA6 Blends, 4

Summary: The effectiveness of some thermoplastic elastomers grafted with maleic anhydride (MA) or with glycidyl methacrylate (GMA) as compatibilizer precursors (CPs) for blends of low density polyethylene (LDPE) with polyamide‐6 (PA) has been studied. The CPs were produced by grafting different amounts of MA or GMA onto a styrene‐block‐(ethylene‐co‐1‐butene)‐block‐styrene copolymer (SEBS) (KRATON G 1652), either in the melt or in solution. A commercially available SEBS‐g‐MA copolymer with 1.7 wt.‐% MA (KRATON FG 1901X) was also used. The effect of the MA concentration and of other characteristics of the SEBS‐g‐MA CPs was also studied. The specific interactions between the CPs and the blends components were investigated through characterizations of the binary LDPE/CP and PA/CP blends, in the whole composition range. It was demonstrated that the SEBS‐g‐GMA copolymers display poor compatibilizing effectiveness due to cross‐linking resulting from reactions of the epoxy rings of these CPs with both the amine and the carboxyl end groups of PA. On the contrary, the compatibilizing efficiency of the MA‐grafted elastomers, as revealed by the thermal properties and the morphology of the compatibilized blends, was shown to be excellent. The results of this study confirm that the anhydride functional groups possess considerably higher efficiency, for the reactive compatibilization of LDPE/PA blends, than those of the ethylene‐acrylic acid and ethylene‐glycidyl methacrylate copolymers investigated in previous works.

SEM micrograph of the 75/25 LD08/PA blend (with 2 phr SEBSMA1).     

Ternary polymer composites: PA6,6/maleated SEBS/glass beads

Polyamide 6,6 (PA6,6)/maleated styrene–hydrogenated butadiene–styrene (SEBS) blends filled with up to 20% spherical glass beads (GBs) were prepared by extrusion and subsequent injection molding. Tensile and impact tests were used to examine the effect of GB additions on the mechanical behavior of PA6,6/SEBS–g–MA 80/20 blend. Tensile measurements showed that the GB additions improve the stiffness of the PA6,6/SEBS–g–MA 80/20 blend but had little effect on its tensile ductility. The impact test revealed that the impact strength of PA6,6/SEBS–g–MA 80/20 blend tends to decrease with increasing GB content. Therefore, the GB additions were beneficial to maintain a stiffness-to-toughness balance of the PA6,6/SEBS–g–MA 80/20 blend. Finally, the correlation between the experimental tensile stiffness and strength with various theoretical models is discussed. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 3231–3237, 2001     

Effects of molecular weight and grafted maleic anhydride of functionalized polylactic acid used in reactive compatibilized binary and ternary blends of polylactic acid and thermoplastic cassava starch

Polylactic acid (PLA) was reactively functionalized with maleic anhydride (MA) and 2,5‐bis(tert‐butylperoxy)?2,5‐dimethylhexane (Luperox 101 or L101) using a twin screw extruder (TSE). The effects of functionality (grafted MA level) and/or number average molecular weight of functionalized PLA (PLA‐g‐MA) as the reactive polymer pairs (binary blends) and reactive compatibilizer (ternary blends) were investigated. Due to the dominant side reaction during melt free radical grafting, polymer degradation or chain scission, PLA‐g‐MA having a higher grafted MA had lower molecular weights and intrinsic viscosity as well as broader molecular weight distribution values. The thermal, physical, mechanical, and morphological properties of binary blends produced by using the TSE and injection molding at a ratio of 70 wt % PLA‐g‐MA and 30 wt % thermoplastic cassava starch (TPCS) were analyzed. The reactive blends having grafted MA more than 0.4 wt % had poor tensile strength and elongation at break. Similar trends in morphology and tensile properties were observed in the reactive ternary blends. The use of PLA‐g‐MA strongly impacted the elongation at break but not the modulus or tensile strength. An increase of PLA‐g‐MA's number average molecular weight ( or M_n) improved the tensile properties of the blends. The reactive ternary blend having 0.1 wt % grafted MA on PLA and PLA‐g‐MA basis and PLA‐g‐MA's M_n of 45 kDa offered the highest elongation at break. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42230.     

Effects of maleated styrene–(ethylene‐co‐butene)–styrene on the morphology and mechanical and thermal properties of polystyrene/polyamide 1212 blends

Polystyrene (PS)/polyamide 1212 (PA 1212) blends were compatibilized with a maleated triblock copolymer of styrene–(ethylene‐co‐butene)–styrene (SEBS‐g‐MA). Scanning electron microscopy revealed that the addition of SEBS‐g‐MA was beneficial to the dispersion of PA 1212 in the PS matrix because of the reaction between them. The variation of the fraction of SEBS‐g‐MA in the blends allowed the manipulation of the phase structure, which first formed a sheetlike structure and then formed a cocontinuous phase containing PA 1212/SEBS‐g‐MA core–shell morphologies. As a result, the mechanical properties, especially the Charpy notched impact resistance, were significantly improved with the addition of SEBS‐g‐MA. Differential scanning calorimetry (DSC) data indicated that the strong interaction between SEBS‐g‐MA and PA 1212 in the blends retarded the crystallization of PA 1212. The heat distortion temperature of the compatibilized blends was improved in comparison with that of the unmodified blend, probably because of the apparent increase in the glass‐transition temperature with an increasing concentration of SEBS‐g‐MA. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 95: 1354–1360, 2005     

Effects of maleated syndiotactic polystyrene on the morphology,mechanical properties,and crystallization behavior of syndiotactic polystyrene/polyamide 6 blends

The compatibilization of syndiotactic polystyrene (sPS)/polyamide 6 (PA‐6) blends with maleic anhydride grafted syndiotactic polystyrene (sPS‐g‐MA) as a reactive compatibilizer was investigated. The sPS/PA‐6 blends were in situ compatibilized by a reaction between the maleic anhydride (MA) of sPS‐g‐MA and the amine end group of PA‐6. The occurrence of the chemical reaction was substantiated by the disappearance of a characteristic MA peak from the Fourier transform infrared spectrum. Morphology observations showed that the size of the dispersed PA‐6 domains was significantly reduced and that the interfacial adhesion was much improved by the addition of sPS‐g‐MA. As a result of reactive compatibilization, the impact strengths of the sPS/PA‐6 blends increased with an increase in the sPS‐g‐MA content. The crystallization behaviors of the blends were affected by the compatibilization effect of sPS‐g‐MA. A single melting peak of sPS in the noncompatibilized blend was gradually split into two peaks as the amount of the compatibilizer increased. A single crystallization peak of PA‐6 in the noncompatibilized blend became two peaks with the addition of 3 wt % sPS‐g‐MA. The new peak was a result of the fractionation crystallization. As the amount of sPS‐g‐MA increased, the intensity of the new peak increased, and the original peak nearly disappeared. Finally, the crystallization peak of PA‐6 disappeared with 20 wt % sPS‐g‐MA in the blend. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 2502–2506, 2003     

Effect of compatibilization on the properties of HIPS/PA1010 blends

Blends consisting of high‐impact polystyrene (HIPS) as the matrix and polyamide 1010 (PA1010) as the dispersed phase were prepared by mixing. The grafting copolymers of HIPS and maleic anhydride (MA), the compatibilizer precursors of the blends, were synthesized. The contents of the MA in the grafting copolymers are 4.7 wt % and 1.6 wt %, and were assigned as HAM and LMA, respectively. Different blend morphologies were observed by scanning electron microscopy (SEM); the domain size of the PA1010 dispersed phase in the HIPS matrix of compatibilized blends decreased comparing with that of uncompatibilized blends. For the blend with 25 wt % HIPS‐g‐MA component, the T_c of PA1010 shifts towards lower temperature, from 178 to 83°C. It is found that HIPS‐g‐MA used as the third component has profound effect on the mechanical properties of the resulting blends. This behavior has been attributed to the chemical reaction taking place in situ during the mixing between the two components of PA1010 and HIPS‐g‐MA. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 799–806, 2000     

The mechanical and rheological behavior of the PA/TPU blend with POE‐g‐MA modifier

In this research, we attempt to improve the impact strength and the viscosity of PA (polyamide) by blending two elastomers, TPU (thermoplastic polyurethane) and POE‐g‐MA (maleic anhydride‐grafted polyethylene‐octene elastomer), in PA matrix with twin screw extruder. The ratio of blending is 80PA/20TPU and 80PA/20TPU/20POE‐g‐MA (66.66PA/16.67TPU/16.67POE‐g‐MA). Results indicate that POE‐g‐MA improves the low viscosity of PA and TPU during the blending process, and also their compatibility. Thus, the 80PA/20TPU/20POE‐g‐MA blend has better tensile stress and elongation than 80PA/20TPU blend, and furthermore POE‐g‐MA significantly improves the impact strength of PA, even to super‐toughness grade. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Toughening of polyamide 6 with a maleic anhydride functionalized acrylonitrile–butadiene–styrene copolymer

Maleic anhydride functionalized acrylonitrile–butadiene–styrene (ABS‐g‐MA) copolymers were prepared via an emulsion polymerization process. The ABS‐g‐MA copolymers were used to toughen polyamide 6 (PA‐6). Fourier transform infrared results show that the maleic anhydride (MA) grafted onto the polybutadiene phase of acrylonitrile–butadiene–styrene (ABS). Rheological testing identified chemical reactions between PA‐6 and ABS‐g‐MA. Transmission electron microscopy and scanning electron microscopy displayed the compatibilization reactions between MA of ABS‐g‐MA and the amine and/or amide groups of PA‐6 chain ends, which improved the disperse morphology of the ABS‐g‐MA copolymers in the PA‐6 matrix. The blends compatibilized with ABS‐g‐MA exhibited notched impact strengths of more than 900 J/m. A 1 wt % concentration of MA in ABS‐g‐MA appeared sufficient to improve the impact properties and decreased the brittle–ductile transition temperature from 50 to 10°C. Scanning electron microscopy results show that the shear yielding of the PA‐6 matrix was the major toughening mechanism. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Blends of polyamide1010 with unmodified and maleic‐anhydride‐grafted high‐impact polystyrene

The crystallization behaviors, dynamic mechanical properties, tensile, and morphology features of polyamide1010 (PA1010) blends with the high‐impact polystyrene (HIPS) were examined at a wide composition range. Both unmodified and maleic‐anhydride‐(MA)‐grafted HIPS (HIPS‐g‐MA) were used. It was found that the domain size of HIPS‐g‐MA was much smaller than that of HIPS at the same compositions in the blends. The mechanical performances of PA1010–HIPS‐g‐MA blends were enhanced much more than that of PA1010–HIPS blends. The crystallization temperature of PA1010 shifted towards higher temperature as HIPS‐g‐MA increased from 20 to 50% in the blends. For the blends with a dispersed PA phase (≤35 wt %), the T_c of PA1010 shifted towards lower temperature, from 178 to 83°C. An additional transition was detected at a temperature located between the T_g's of PA1010 and PS. It was associated with the interphase relaxation peak. Its intensity increased with increasing content of PA1010, and the maximum occurred at the composition of PA1010–HIPS‐g‐MA 80/20. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 857–865, 1999     

Thermoplastic biodegradable material elaborated from unripe banana flour reinforced with metallocene catalyzed polyethylene

To meet the challenge of procuring new sources of natural polymers without affecting the demands for food crops, a thermoplastic unripe banana flour (TPF) was produced, characterized, and blended with metallocene‐catalyzed polyethylene (mPE). Both the pulp and peels of unripe banana were used to produce flour, whose stability and thermoplastic properties allowed blending with mPE in high proportions, that is, 50, 60, 70, and 80%. The blends were injection molded, and the thermal, mechanical, microstructural, and infrared spectral properties of the resulting samples were characterized. The blend containing 50% TPF yielded a robust, elastic, and nonbrittle material. Maleic anhydride grafting on mPE (mPE‐g‐MA) promoted interphase adhesion of the polymers and homogeneity in the blends. Grafting also influenced the mechanical, thermal, and microstructural properties of the blends. The characteristics of the blends make them ideal for designing biodegradable plastics while exploiting banana peels, which are usually considered agricultural waste. POLYM. ENG. SCI., 55:866–876, 2015. © 2014 Society of Plastics Engineers     

Polyethylene grafted maleic anhydride to improve wettability of liquid on polyethylene films

Blends of linear low density polyethylene (LLDPE) and LLDPE grafted maleic anhydride (LLDPE‐g‐MA) were prepared by melt mixing. The surface of cast films with different contents and types of maleated PE were characterized through contact angle and wetting tension measurements, as well as attenuated total reflection IR spectroscopy. The tensile properties and light transmission of extruded films, as well as the performance of these films compared with commercial “antifog” films, for greenhouses were determined. The carbonyl polar groups on the surface of LLDPE/LLDPE‐g‐MA blends increased, and the equilibrium contact angles of water and dimethylformamide decreased when the content of maleated PE increased. Films made with these blends showed a noticeable reduction in water drop formation as the MA content was increased and when using LLDPE‐g‐MA of lower molecular weight. The light transmission through these films under condensation was improved when using increased contents of MA, which promotes better wetting of the water on the surface. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 79: 1802–1808, 2001     

Gasoline permeation behavior and mechanical properties of polyamide 6/nanoclay,polyamide 6/PE‐g‐maleic anhydride blend,and polyamide 6/PE‐g‐maleic anhydride/clay nanocomposite

In this article, polyamide 6 (PA6)/clay nanocomposites, PA6/polyethylene grafted maleic anhydride (PE‐g‐MA) blends, and PA6/PE‐g‐MA/clay nanocomposites were prepared and their gasoline permeation behavior and some mechanical properties were investigated. In PA6/clay nanocomposites, cloisite 30B was used as nanoparticles, with weight percentages of 1, 3, and 5. The blends of PA6/PE‐g‐MA were prepared with PE‐g‐MA weight percents of 10, 20, and 30. All samples were prepared via melt mixing technique using a twin screw extruder. The results showed that the lowest gasoline permeation occurred when using 3 wt % of nanoclay in PA6/clay nanocomposites, and 10 wt % of PE‐g‐MA in PA6/PE‐g‐MA blends. Therefore, a sample of PA6/PE‐g‐MA/clay nanocomposite containing 3 wt % of nanoclay and 10 wt % of PE‐g‐MA was prepared and its gasoline permeation behavior was investigated. The results showed that the permeation amount of PA6/PE‐g‐MA/nanoclay was 0.41 g m^?2 day^?1, while this value was 0.46 g m^?2 day^?1 for both of PA6/3wt % clay nanocomposite and PA6/10 wt % PE‐g‐MA blend. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40150.