Development of high Tg epoxy resin and mechanical properties of its fiber‐reinforced composites

A new epoxy resin with high glass transition temperature (T_g) (～ 180°C) and a viscosity low enough for infiltration into dry reinforcements at 40°C was developed for the vacuum‐assisted resin transfer molding process. To study the curing behavior and viscosity, several blends were formulated using multifunctional resin, aromatic hardener, and reactive diluents. Effects of these components on the viscosity and T_g were investigated by thermomechanical analysis, dynamic scanning calorimetry, and rheometer. Experimental results showed that a liquid aromatic hardener and multifunctional epoxy resin should be used to decrease the viscosity to <1 Pa·s at 40°C. Moreover, the addition of a proper reactive diluent decreased the viscosity and simultaneously minimized the deterioration of T_g. Mechanical properties of the composite produced with the optimized blend were evaluated at both room‐temperature and high‐temperature conditions. According to the results, the composite showed comparable mechanical properties with that of the current commercial resin. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Physical and mechanical properties of kenaf/flax hybrid composites

This research investigates the physical and mechanical properties of hybrid composites made of epoxy reinforced by kenaf and flax natural fibers to investigate the hybridization influences of the composites. Pure and hybrid composites were fabricated using bi-directional kenaf and flax fabrics at different stacking sequences utilizing the vacuum-assisted resin infusion method. The pure and hybrid composites' physical properties, such as density, fiber volume fraction (FVF), water absorption capacity, and dimensional stability, were measured. The tests of tensile, flexural, interlaminar shear and fracture toughness (Mode II) were examined to determine the mechanical properties. The results revealed that density remained unchanged for the hybrid compared to pure kenaf/epoxy composites. The tensile, flexural, and interlaminar shear performance of flax/epoxy composite is improved by an increment of kenaf FVF in hybrid composites. The stacking sequence significantly affected the mechanical properties of hybrid composites. The highest tensile strength (59.8 MPa) was obtained for FK2 (alternative sequence of flax and kenaf fibers). However, FK3 (flax fiber located on the outer surfaces) had the highest interlaminar shear strength (12.5 MPa) and fracture toughness (3302.3 J/m²) among all tested hybrid composites. The highest water resistance was achieved for FK5 with the lowest thickness swelling.     

短碳纤维增强碳化硅基复合材料的制备

短纤维的分散均匀性一直是短纤维复合材料应用受限的主要原因．采用固相球磨分散和熔融渗硅工艺,可得到均匀分散的短碳纤维增强碳化硅基复合材料．并利用金相显微镜见察复合材料微观形貌,测试复合材料的抗弯强度和断后韧性．     

The effect of fiber concentration on mechanical and thermal properties of fiber‐reinforced polypropylene composites

A novel composite material consisting of polypropylene (PP) fibers in a random poly(propylene‐co‐ethylene) (PPE) matrix was prepared and its properties were evaluated. The thermal and mechanical properties of PP–PPE composites were studied by dynamic mechanical analysis (DMA) and differential scanning calorimetry (DSC) with reference to the fiber concentration. Although, by increasing PP fiber concentration in PPE, no significant difference was found in melting and crystallization temperatures of the PPE, the storage, and the tensile and flexural modulus of the composites increased linearly with fiber concentrations up to 50%, 1.5, 1.0, 1.3 GPa, respectively, which was approximately four times higher than that for the pure PPE. There is a shift in glass transition temperature of the composite with increasing fiber concentration in the composite and the damping peak became flatter, which indicates the effectiveness of fiber–matrix interaction. A higher concentration of long fibers (>50% w/w) resulted in fiber packing problems, difficulty in dispersion, and an increase in void content, which led to a reduction in modulus. Cox–Krenchel and Haplin–Tsai equations were used to predict tensile modulus of random fiber‐reinforced composites. A Cole–Cole analysis was performed to understand the phase behavior of the composites. A master curve was constructed based on time–temperature superposition (TTS) by using data over the temperature range from −50 to 90°C, which allowed for the prediction of very long and short time behavior of the composite. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 2260–2272, 2005     

Preparation and mechanical properties of high‐performance short ramie fiber‐reinforced polypropylene composites

Short ramie fiber (RF) was used to reinforce the polypropylene (PP). The composites were prepared in a twin‐screw extruder followed by injection molding. The experimental results showed that both the strength and the modulus of the composites increase considerably with increasing RF content. The tensile strength and flexural strength are as high as 67 and 80 MPa by the incorporation of ramie up to 30 wt %. To the best of our knowledge, this is one of the best results for short natural fiber‐reinforced PP composites. However, the preparation method in this study is more simple and economic. This short RF‐reinforced PP composites extend the application field for short‐nature fiber‐reinforced PP composites. Morphological analysis revealed that it is the high aspect ratio of the fiber and good interfacial compatibility that result in the high performance of the composites. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Influence of thermooxidative aging on the static and dynamic mechanical properties of long‐glass‐fiber‐reinforced polyamide 6 composites

The static and dynamic mechanical properties, thermal behaviors, and morphology of pure long‐glass‐fiber‐reinforced samples [polyamide 6 (PA6)/long glass fiber (LGF)] with different thermal exposure times at 160°C were studied by comparison with stabilized samples in this study. The aging mechanism of the PA6/LGF samples under heat and oxygen was studied with the methods of thermal Fourier transform infrared (FTIR), differential scanning calorimetry, dynamic mechanical analysis, scanning electron microscopy (SEM), and so on. The results indicate that the static mechanical strength, melting temperature, and crystallization temperature decreased because of the decomposition of the macromolecular chain of PA6 resin and the debonding of the interface between the glass fibers and matrix. The glass‐transition temperature and crystallinity also increased and decreased, respectively, after aging. The macromolecular chain decomposition dominated in the subsequent aging process; this resulted in many sharp and brittle microcracks appearing on the surfaces of the aged samples, as shown by SEM and the FTIR spectra. The existence of stabilizers endowed the PA6/LGF composites with better retention of static and dynamic mechanical properties. The reason was that the metal ions of the copper salt antioxidant acted as an anti‐aging catalyst in the reinforced PA6 system. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39594.     

Dynamic mechanical properties of three‐component composites (acrylic polymer/epoxy/SiO2) in the glass‐transition region

In previous studies, we reported the linear and nonlinear rheological properties of three‐component composites consisting of acrylic polymer (AP), epoxy resin (EP), and various SiO₂ contents (AP/EP/SiO₂) in the molten state. In this study, the dynamic mechanical properties of AP/EP/SiO₂ composites with different particle sizes (0.5 and 8 μm) were investigated in the glass‐transition region. The EP consisted of three kinds of EP components. The α relaxation due to the glass transition shifted to a higher temperature with an increase in the volume fraction (?) for the AP/EP/SiO₂ composites having a particle size of 0.5 μm, but the α relaxation scarcely shifted for the composite having a particle size of 8 μm as a general result. This result suggested that the SiO₂ nanoparticles that were 0.5 μm in size adsorbed a lot of the low‐glass‐transition‐temperature (T_g) component because of their large surface area. The AP/SiO₂ composites did not exhibit a shift in T_g; this indicated that the composite did not adsorb any component. The modulus in the glassy state (E′_g) exhibited a very weak &phis; dependence for the AP/EP/SiO₂ composites having particle sizes of 0.5 and 8 μm, although E′_g of the AP/SiO₂ composites increased with &phis;. The AP/EP/SiO₂ composites exhibited a peculiar dynamic mechanical behavior, although the AP/SiO₂ composites showed the behavior of general two‐component composites. Scanning electron microscopic observations indicated that some components in the EP were adsorbed on the surface of the SiO₂ particles. We concluded that the peculiar behavior of the AP/EP/SiO₂ composites was due to the selective adsorption of the EP component. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40409.     

Fabrication and mechanical properties of glass fiber‐reinforced wood plastic hybrid composites

To fully utilize the resource in the municipal solid waste (MSW) and improve the strength and toughness of wood plastic composites, glass fiber (GF)‐reinforced wood plastic hybrid composites (GWPCs) were prepared through compounding of recycled high‐density polyethylene (HDPE) from MSW, waste wood fibers, and chopped GF. Mechanical tests of GWPCs specimens with varying amounts of GF content were carried out and the impact fractured surface of GWPCs was observed through scanning electron microscope (SEM). The tensile strength of GWPCs and the efficiency coefficient values were predicted by Kelly‐Tyson method. The results indicated that the tensile strength and impact strength of GWPCs could be improved simultaneously by adding type L chopped GF (L‐GF), and would be dropped down when type S chopped GF (S‐GF) was included. The tensile strength of GWPCs was well accordant with the experimental result. The efficiency coefficient values of S‐GF and L‐GF are ?0.19 and 0.63, respectively. Inspection of SEM micrographs indicated that L‐GF had achieved full adhesion with the plastic matrix through addition of maleic anhydride‐g‐polyethylene. The main fracture modes of GWPCs included pullout of GF, broken of matrix, and interfacial debonding. Because of the synergistic effects between hybrid components in GF/wood fiber/HDPE hybrid system, a special 3D network microstructure was formed, which was the main contribution to the significant improvement in the tensile strength and impact strength of L‐GF‐reinforced hybrid composites. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Effect of layering pattern on dynamic mechanical properties of randomly oriented short banana/sisal hybrid fiber–reinforced polyester composites

Dynamic mechanical test methods have been widely employed for investigating the structures and viscoelastic behavior of polymeric materials to determine their relevant stiffness and damping characteristics for various applications. Randomly oriented short banana/sisal hybrid fiber–reinforced polyester composites were prepared by keeping the volume ratio of banana and sisal 1 : 1 and the total fiber loading 0.40 volume fraction. Bilayer (banana/sisal), trilayer (banana/sisal/banana and sisal/banana/sisal), and intimate mix composites were prepared. The effect of layering pattern on storage modulus (E′), damping behavior (tan δ), and loss modulus (E″) was studied as a function of temperature and frequency. Bilayer composite showed high damping property while intimately mixed and banana/sisal/banana composites showed increased stiffness compared to the other pattern. The Arrhenius relationship has been used to calculate the activation energy of the glass transition of the composites. The activation energy of the intimately mixed composite was found to be the highest. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 2168–2174, 2005     

Mechanical properties of injection‐molded isotactic polypropylene/roselle fiber composites

Natural fiber‐thermoplastic composite materials, based on their cost‐effectiveness and environmental friendliness, have attracted much interest both scientifically and technologically in recent years. Other advantages of natural fibers are good specific strength, less abrasion, and less irritation upon inhalation (in comparison with some common inorganic fillers). In the present contribution, roselle (Hibiscus sabdariffa L.) fibers were chosen and used as reinforcing fillers for isotactic polypropylene (iPP) for the first time, due mainly to the cost‐effectiveness and natural abundance on Thai soil. Processibility and mechanical properties of the resulting composites were investigated against the type and the mean size of the fibers. The results showed that the highest mechanical properties were observed when roselle bast fibers were incorporated. When whole‐stalk (WS) fibers (i.e., the weight ratio of bast and core fibers was 40 : 60 w/w) were used, moderate mechanical properties of the resulting composites were realized. The optimal contents of the WS fibers and the maleic anhydride‐grafted iPP compatibilizer that resulted in an improvement in some of the mechanical properties of the resulting composites were 40 and 7 wt %, respectively. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3291–3300, 2006     

Mechanical and dynamic mechanical properties of epoxy syntactic foams reinforced by short carbon fiber

Epoxy syntactic foams were prepared with diglycidyl ether of bisphenol‐A (DGEBA) epoxy resin, 2.4.6‐tri(dimethylaminomethyl)phenol (DMP‐30), coupling treated microsphere and short carbon fiber. The density of the foam was maintained between 0.56 and 0.91 g/cm³ for all compositions. Compressive, flexural, tensile and dynamic mechanical properties of the foams were investigated with respect to hollow glass microsphere (HGM) and carbon fiber (CF) content. A considerable improvement in the mechanical properties viz. compressive, flexural and tensile strengths was observed for the foams on incorporation of a small quantity of CF. The storage modulus were higher for the foam composites containing CF. The presence of HGM has significant influence on T_g of the syntactic foams, spherical filler diminished the T_g of the syntactic foams due to the plasticizing effect of the coupling treatment of HGM, that is helpful for enhancing damping properties of syntactic foams. POLYM. COMPOS., 37:1960–1970, 2016. © 2015 Society of Plastics Engineers     

Effect of fiber treatment on the mechanical properties of hybrid fiber reinforced polystyrene composites. Part II. Use of glass fiber and wood pulp as hybrid fiber

The mechanical properties of polystyrene reinforced with a mixture of hardwood aspen chemithermomechanical pulp (CTMP) and surface-treated glass fiber have been studied. The adhesion of cellulose fiber to glass fiber as well as to thermoplastics improved thanks to various surface treatments of CTMP, e.g. coating with polymer+isocyanate or with silane, and grafting with polystyrene. In general, compared with non-treated CTMP-filled composites, the mechanical properties improved when surface-treated wood fiber was used as a filler. Experimental results indicate better compatibility between treated wood fiber and surface-treated glass fiber as well as polystyrene and, consequently, the mechanical properties were enhanced.     

Structure and properties of UHMWPE fiber/carbon fiber hybrid composites

Ultrahigh molecular weight polyethylene (UHMWPE) fiber/carbon fiber hybrid composites were prepared by inner‐laminar and interlaminar hybrid way. The mechanical properties, dynamic mechanical analysis (DMA), and morphologies of the composites were investigated and compared with each other. The results show that the hybrid way was the major factor to affect mechanical and thermal properties of hybrid composites. The resultant properties of inner‐laminar hybrid composite were better than that of interlaminar hybrid composite. The bending strength, compressive strength, and interlaminar shear strength of hybrid composites increased with an increase in carbon fiber content. The impact strength of inner‐laminar hybrid composite was the largest (423.3 kJ/m²) for the UHMWPE fiber content at 43 wt % to carbon fiber. The results show that the storage modulus (E′), dissipation factor (tan δ), and loss modulus (E″) of the inner‐laminar hybrid composite shift toward high temperature remarkably. The results also indicate that the high‐performance composite with high strength and heat resistance may be prepared by fibers' hybrid. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1880–1884, 2006     

Preparation and dynamic mechanical properties of polyurethane‐modified epoxy composites filled with functionalized fly ash particulates

Fly ash (FA) is a porous ceramic, which has proved to have some favorable functions. In this article, we have prepared a series of fly ash filled composites, where the polyurethane‐(PU) modified epoxy (EP) was acted as the matrix. With the purpose of characterizing the effect of the content of PU in the matrices and the surface‐treatment (ST) of fly ash particulates on the dynamic mechanical properties of composites, Fourier transform infrared spectral analysis (FTIR), microstructure observation, impact property test as well as dynamic mechanical analysis (DMA) were systematically investigated. With FTIR test, it can be found that the chemical reactions occur, and new chemical structures are formed between EP and PU, and the functionalized groups existing on the surface of fly ash particulates can also be detected. In fractographs observation of composites, it can be seen that the silane coupling agent improves the interfacial bonding conditions between fly ash particulates and the matrix. Impact property test result reveals that PU improves the toughness of EP. Dynamic mechanical analysis of the composites is carried out from ?40 to 150°C using a tension‐compression mode. Results show that the composites, whose matrices are with 10 and 20 wt % PU, may possess better dynamic mechanical properties as compared with the other composites. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Investigation of mechanical properties of alumina nanoparticle‐loaded hybrid glass/carbon‐fiber‐reinforced epoxy composites

This research work investigates the tensile strength and elastic modulus of the alumina nanoparticles, glass fiber, and carbon fiber reinforced epoxy composites. The first type composites were made by adding 1–5 wt % (in the interval of 1%) of alumina to the epoxy matrix, whereas the second and third categories of composites were made by adding 1–5 wt % short glass, carbon fibers to the matrix. A fourth type of composite has also been synthesized by incorporating both alumina particles (2 wt %) and fibers to the epoxy. Results showed that the longitudinal modulus has significantly improved because of the filler additions. Both tensile strength and modulus are further better for hybrid composites consisting both alumina particles and glass fibers or carbon fibers. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39749.     

Effect of fiber treatments on mechanical properties of coir or oil palm fiber reinforced polyester composites

The use of plant fibers as a reinforcement in polyester matrices requires the issue of compatibility between the two phases to be addressed. Because plant fibers present hydrophilic surfaces and polyesters are generally hydrophobic, poor fiber–matrix dispersion and wetting of the fibers by the matrix may result. As a consequence, the mechanical properties of the composite are severely reduced. This study considers the effect of fiber treatment by chemical modification of the fibers (acetylation) or the use of silane or titanate coupling agents on the mechanical properties of coir or oil palm reinforced polyester composites. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 78: 1685–1697, 2000     

Thermal and mechanical properties of plasticized poly(L‐lactic acid)

Acetyl tri‐n‐butyl citrate (ATBC) and poly(ethyleneglycol)s (PEGs) with different molecular weights (from 400 to 10000) were used in this study to plasticize poly(L‐lactic acid) (PLA). The thermal and mechanical properties of the plasticized polymer are reported. Both ATBC and PEG are effective in lowering the glass transition (T_g) of PLA up to a given concentration, where the plasticizer reaches its solubility limit in the polymer (50 wt % in the case of ATBC; 15–30 wt %, depending on molecular weight, in the case of PEG). The range of applicability of PEGs as PLA plasticizers is given in terms of PEG molecular weight and concentration. The mechanical properties of plasticized PLA change with increasing plasticizer concentration. In all PLA/plasticizer systems investigated, when the blend T_g approaches room temperature, a stepwise change in the mechanical properties of the system is observed. The elongation at break drastically increases, whereas tensile strength and modulus decrease. This behavior occurs at a plasticizer concentration that depends on the T_g‐depressing efficiency of the plasticizer. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1731–1738, 2003     

Effects of amino‐functionalized carbon nanotubes on the properties of amine‐terminated butadiene–acrylonitrile rubber‐toughened epoxy resins

Amino‐functionalized multiwalled carbon nanotubes (MWCNT‐NH₂s) as nanofillers were incorporated into diglycidyl ether of bisphenol A (DGEBA) toughened with amine‐terminated butadiene–acrylonitrile (ATBN). The curing kinetics, glass‐transition temperature (T_g), thermal stability, mechanical properties, and morphology of DGEBA/ATBN/MWCNT‐NH₂ nanocomposites were investigated by differential scanning calorimetry (DSC), thermogravimetric analysis, a universal test machine, and scanning electron microscopy. DSC dynamic kinetic studies showed that the addition of MWCNT‐NH₂s accelerated the curing reaction of the ATBN‐toughened epoxy resin. DSC results revealed that the T_g of the rubber‐toughened epoxy nanocomposites decreased nearly 10°C with 2 wt % MWCNT‐NH₂s. The thermogravimetric results show that the addition of MWCNT‐NH₂s enhanced the thermal stability of the ATBN‐toughened epoxy resin. The tensile strength, flexural strength, and flexural modulus of the DGEBA/ATBN/MWCNT‐NH₂ nanocomposites increased increasing MWCNT‐NH₂ contents, whereas the addition of the MWCNT‐NH₂s slightly decreased the elongation at break of the rubber‐toughened epoxy. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40472.     

Mechanical properties of carbon fiber reinforced bisphenol A dicyanate ester composites modified with multiwalled carbon nanotubes

A novel electrophoretic deposition (EPD) method was employed for grafting multiwalled carbon nanotubes (MWCNTs) on carbon fibers, which, after impregnation with bisphenol A dicyanate ester (BADCy), synergistically reinforced BADCy matrix composites (CNT‐C/BADCy). The effect of MWCNT presence on the mechanical properties of the composites was investigated. Composite tensile strength increased by 45.2% for an EPD duration of 2 min, while flexural strength exhibited a decreasing trend with EPD duration. Optical microscopy revealed that the existence of MWCNTs enhanced the fiber‐matrix interface while a large number of CNTs were observed to have pulled‐out from the matrix, a finding which explained the observed tensile strength increase in terms of energy dissipation by the specific toughening mechanism. The flexural strength decrease of the composites with CNTs as compared to specimens without nanotubes was found linked to the increased stress concentration in the BADCy matrix due to tube presence which weakens the adhesion between carbon fabrics. In a word, carbon nanotubes will enhance the micro interface and weaken the macro interface of the composites. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45100.     

Injection‐molded short hemp fiber/glass fiber‐reinforced polypropylene hybrid composites—Mechanical,water absorption and thermal properties

Natural fiber‐based thermoplastic composites are generally lower in strength performance compared to thermoset composites. However, they have the advantage of design flexibility and recycling possibilities. Hybridization with small amounts of synthetic fibers makes these natural fiber composites more suitable for technical applications such as automotive interior parts. Hemp fiber is one of the important lignocellulosic bast fiber and has been used as reinforcement for industrial applications. This study focused on the performance of injection‐molded short hemp fiber and hemp/glass fiber hybrid polypropylene composites. Results showed that hybridization with glass fiber enhanced the performance properties. A value of 101 MPa for flexural strength and 5.5 GPa for the flexural modulus is achieved from a hybrid composite containing 25 wt % of hemp and 15 wt % of glass. Notched Izod impact strength of the hybrid composites exhibited great enhancement (34%). Analysis of fiber length distribution in the composite and fracture surface was performed to study the fiber breakage and fracture mechanism. Thermal properties and resistance to water absorption properties of the hemp fiber composites were improved by hybridization with glass fibers. Overall studies indicated that the short hemp/glass fiber hybrid polypropylene composites are promising candidates for structural applications where high stiffness and thermal resistance is required. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 2432–2441, 2007