UASB/曝气沉淀/IC反应器处理高浓度硫酸盐有机废水

在赤霉素生产过程中产生的高浓度硫酸盐有机废水,处理难度较大。采用UASB／曝气沉影IC反应器工艺处理该废水,UASB中的硫酸盐还原菌将硫酸根还原为硫化物,曝气池中的脱硫杆菌则将硫化物氧化为单质硫,并在沉淀池中去除,IC反应器去除COD。系统稳定运行后,对硫酸盐的去除率〉90％,对COD的去除率〉80％。     

Effect of specific gas loading rate on thermophilic (55 degrees C) acidifying (pH 6) and sulfate reducing granular sludge reactors

The effect of the specific gas loading rate on the acidifying, sulfate reducing and sulfur removal capacity of thermophilic (55 degrees C; pH 6.0) granular sludge bed reactors treating partly acidified wastewater was investigated. A comparison was made between a regular UASB reactor and a UASB reactor continuously sparged with N(2) at a specific gas loading rate of 30 m(3)m(-2)d(-1). Both UASB reactors (upflow velocity 1.0 mh(-1), hydraulic retention time about 5h) were fed a synthetic wastewater containing starch, sucrose, lactate, propionate and acetate and a low sulfate concentration (COD/SO(4)(2-) ratio of 10) at volumetric organic loading rates (OLR) ranging from 4.0 to 49.8 gCODl(-1) reactord(-1). Immediately after imposing an OLR of 25 gCODl(-1) reactord(-1), the acidification and sulfate reduction efficiency dropped to 80% and 30%, respectively, in the UASB reactor. Both efficiencies recovered slowly to 100% during the course of the experiment. In the N(2) sparged reactor, both the acidification and sulfate reduction efficiency remained 100% following the OLR increase to 25 gCODl(-1) reactord(-1). However, the sulfate reduction efficiency gradually decreased to about 20% at the end of the experiment. The biogas (CO(2) and CH(4)) production rate in the UASB was very low, i.e. <3l biogasl(-1) reactorday(-1), resulting in negligible amounts (<20%) of H(2)S stripped from the reactor liquid. The total H(2)S concentration of the N(2) sparged UASB reactor effluent was always below 25 mgl(-1), but incomplete sulfate reduction kept the maximal H(2)S stripping efficiency below 70%.     

Organic removal by denitritation and methanogenesis and nitrogen removal by nitritation from landfill leachate

A system consisting of a two-stage UASB and anoxic-oxic reactor was used to enhance COD and nitrogen removal from landfill leachate. To improve denitrification efficiency, the raw leachate with recycled final effluent was pumped into the first-stage UASB (UASB1) to carry out simultaneous denitrification and methanogenesis. The results over 180 d show that the maximum organic removal rate in UASB1 and UASB2 was 12.5 and 8.5 kgCODm(-3)d(-1) in the oxic zone of the A/O reactor, respectively. The COD and biochemical oxygen demand (BOD5) removal efficiency of the system was 80-92% and about 99%, respectively. Without controlling temperature (17-30 degrees C) and dissolved oxygen (0.5-4.0 mgL(-1)), the maximum NH4+-N removal rate was 0.68 kg NH4+-Nm(-3)d(-1), and about 99% of NH4+-N removal was obtained by nearly complete nitritation. The 81-93% total nitrogen removal was obtained by complete denitrification in the UASB1 and in the anoxic zone of the A/O reactor. Fluorescence in situ hybridization (FISH) analysis of the sludge samples from A/O reactor showed that ammonia oxidizing bacteria (AOB) consisted 4% of the eubacterium, while nitrite oxidizing bacteria (NOB) counted less than 0.2% of that. The study shows that the main factors achieving and maintaining nitritation are a proper range of free ammonia concentration obtained by dilution recycled final effluent that inhibits NOB but not AOB; effective control on aeration time by indication of "ammonia valley" on pH profile; and highly efficient denitrification and its reproducing alkalinity to result in pH above 8.5.     

Steady-state model-based evaluation of sulfate reduction, autotrophic denitrification and nitrification integrated (SANI) process

Recently we developed a process for wastewater treatment in places where part of the fresh water usage is replaced by seawater usage. The treatment of this saline sewage consists of sulfate reduction, autotrophic denitrification and nitrification integrated (SANI) process. The process consists of an up-flow anaerobic sludge bed (UASB) for sulfate reduction, an anoxic filter for autotrophic denitrification using dissolved sulfide produced in the UASB and an aerobic filter for nitrification. The system was operated for 500 days with 97% COD removal and 74% total nitrogen removal without withdrawal of sludge. To verify these results and to understand this novel process, a steady-state model was developed from the COD, nitrogen and sulfur mass and charge balances based on the stoichiometries of the sulfate reduction, the autotrophic denitrification and the autotrophic nitrification. The model predictions agreed well with measured data on COD, nitrate and sulfate removal, sulfide production, effluent TSS, and mass balances of COD, sulfur and nitrogen in the three reactors. The model explains why withdrawal of sludge from the SANI system is not needed through comparisons of the predictions and measurements of effluent TSS and phosphorus concentrations.     

Anaerobic biodegradability and treatment of grey water in upflow anaerobic sludge blanket (UASB) reactor

Feasibility of grey water treatment in an upflow anaerobic sludge blanket (UASB) reactor operated at different hydraulic retention time (HRT) of 16, 10 and 6h and controlled temperature of 30 degrees C was investigated. Moreover, the maximum anaerobic biodegradability without inoculum addition and maximum removal of chemical oxygen demand (COD) fractions in grey water were determined in batch experiments. High values of maximum anaerobic biodegradability (76%) and maximum COD removal in the UASB reactor (84%) were achieved. The results showed that the colloidal COD had the highest maximum anaerobic biodegradability (86%) and the suspended and dissolved COD had similar maximum anaerobic biodegradability of 70%. Furthermore, the results of the UASB reactor demonstrated that a total COD removal of 52-64% was obtained at HRT between 6 and 16 h. The UASB reactor removed 22-30% and 15-21% of total nitrogen and total phosphorous in the grey water, respectively, mainly due to the removal of particulate nutrients. The characteristics of the sludge in the UASB reactor confirmed that the reactor had a stable performance. The minimum sludge residence time and the maximum specific methanogenic activity of the sludge ranged between 27 and 93 days and 0.18 and 0.28 kg COD/(kg VS d).     

Tannery effluent as a carbon source for biological sulphate reduction

Tannery effluent was assessed as a carbon source for biological sulphate reduction in a pilot-scale upflow anaerobic sludge blanket (UASB), stirred tank reactor (STR) and trench reactor (TR). Sulphate removals of between 60-80% were obtained in all three reactors at total sulphate feed levels of up to 1800 mg l(-1). Sulphate removal in the TR (400-500 mg SO4 l(-1) day(-1)) and UASB (up to 600 mg SO4 l(-1) day(-1)) were higher than those obtained in the STR (250 mg SO4 l(1) day(-1)). A change in operation mode from a UASB to a STR had a large impact on chemical oxygen demand (COD) removal efficiencies. COD removal rates decreased by 25% from 600-700 mg COD l(-1) day(-1) to 200-600 mg COD l(-1) day(-1). The TR had an average COD removal rate of 500 mg COD l(-1) day(-1). Large quantities of sulphide were produced in the reactors (up to 1500 mg l(-1)). However due to the elevated pH in the reactor, only a small amount was in the form of H2S and thus the odour problem normally associated with biological sulphate reduction was not present.     

Effect of process configuration and substrate complexity on the performance of anaerobic processes

The roles of substrate complexity (molecular size of the substrate) and process configuration in anaerobic wastewater treatment were investigated to determine optimal methanogenic technology parameters. Five substrates (glucose, propionate, butyrate, ethanol, and lactate) plus a mixed waste (60% carbohydrate, 34% protein, and 6% lipids) were studied under five reactor configurations: batch-fed single-stage continuous stirred tank reactor (CSTR), continuously fed single-stage CSTR, two-phase CSTR, two-stage CSTR, and single-stage upflow anaerobic sludge blanket (UASB). The substrate feed concentration was 20,000 mg/L as COD. The solids retention time (SRT) and hydraulic retention time (HRT) in the CSTR reactors were 20 d, while HRT in the UASB was 2 d. All reactors were operated for at least 60 d (equal to 3SRT). Substrate complexity was observed to be less significant under two-phase, two-stage and UASB reactor configurations. Two-phase CSTR, two-stage CSTR, and single-stage UASB configurations yielded the lowest effluent chemical oxygen demands (130-550, 60-700, and 50-250 mg/L, respectively). The highest effluent chemical oxygen demands were detected when feeding glucose, propionate, and lactate to continuously fed single-stage CSTRs (10, 400, 9900, and 4700 mg/L COD, respectively) and to batch-fed single-stage CSTRs (11, 200, 2500, and 2700 mg/L COD, respectively). Ironically, the one stage CSTR--most commonly utilized in the field--was the worst possible reactor configuration.     

Application of bacteria involved in the biological sulfur cycle for paper mill effluent purification

In anaerobic wastewater treatment, the occurrence of biological sulfate reduction results in the formation of unwanted hydrogen sulfide, which is odorous, corrosive and toxic. In this paper, the role and application of bacteria in anaerobic and aerobic sulfur transformations are described and exemplified for the treatment of a paper mill wastewater. The sulfate containing wastewater first passes an anaerobic UASB reactor for bulk COD removal which is accompanied by the formation of biogas and hydrogen sulfide. In an aeration pond, the residual COD_organic and the formed dissolved hydrogen sulfide are removed. The biogas, consisting of CH₄ (80-90 vol.%), CO₂ (10-20 vol.%) and H₂S (0.8-1.2 vol.%), is desulfurised prior to its combustion in a power generator thereby using a new biological process for H₂S removal. This process will be described in more detail in this paper. Biomass from the anaerobic bioreactor has a compact granular structure and contains a diverse microbial community. Therefore, other anaerobic bioreactors throughout the world are inoculated with biomass from this UASB reactor. The sludge was also successfully used in investigation on sulfate reduction with carbon monoxide as the electron donor and the conversion of methanethiol. This shows the biotechnological potential of this complex reactor biomass.     

产甲烷UASB中颗粒污泥的快速培养及特性研究

在两相厌氧反应器的基础上,进行了产甲烷UASB中颗粒污泥的快速培养及特性研究.采用低负荷启动方式,通过快速提高进水COD和缩短水力停留时间使产甲烷UASB在最佳条件下运行,36d后产甲烷UASB中粒径>1.0 mm的颗粒污泥占64%,出水COD稳定在300 mg/L以下,可认为颗粒污泥培养成功.颗粒污泥的成熟经历了形成不规则核心、挤压架桥、分割成长、修剪长大四个阶段,加速污泥颗粒化的因素包括适宜的生长环境、良好的水力特征等.     

Anaerobic sewage treatment in a one-stage UASB reactor and a combined UASB-Digester system

The treatment of sewage at 15 degrees C was investigated in a one-stage upflow anaerobic sludge blanket (UASB) reactor and a UASB-Digester system. The latter consists of a UASB reactor complemented with a digester for mutual sewage treatment and sludge stabilisation. The UASB reactor was operated at a hydraulic retention time of 6h and a controlled temperature of 15 degrees C, the average sewage temperature during wintertime of some Middle East countries. The digester was operated at 35 degrees C. The UASB-Digester system provided significantly (significance level 5%) higher COD removal efficiencies than the one-stage UASB reactor. The achieved removal efficiencies in the UASB-Digester system and the one-stage UASB reactor for total, suspended, colloidal and dissolved COD were 66%, 87%, 44% and 30%, and 44%, 73%, 3% and 5% for both systems, respectively. The stability values of the wasted sludge from the one-stage UASB reactor and the UASB-Digester system were, respectively, 0.47 and 0.36g CH(4)-COD/g COD. Therefore, the anaerobic sewage treatment at low temperature in a UASB-Digester system is promising.     

Inhibition of sulfate-reducing and methanogenic activities of anaerobic sewer biofilms by ferric iron dosing

Ferric iron is commonly used for sulfide precipitation in sewers, thus achieving corrosion and odour control. Its impact on the activities of sulfate-reducing bacteria and methanogens in anaerobic sewer biofilms is investigated in this study. Two lab-scale rising main sewer systems fed with real sewage were operated for 8 months. One received Fe³⁺ dosage (experimental system) and the other was used as a control. In addition to precipitating sulfide from bulk water, Fe³⁺ dosage was found to significantly inhibit sulfate reduction and methane production by sewer biofilms. The experimental reactor discharged an effluent containing a higher concentration of sulfate and a lower concentration of methane in comparison with the reference reactor. Batch experiments showed that the addition of ferric ions reduced the sulfate reduction and methane production rates of the sewer biofilms by 60% and 80%, respectively. The batch experiments further showed that Fe³⁺ dosage changed the final products of sulfate reduction with sulfide accounting for only 54% of the sulfate reduced. The other products could not be confirmed, but were not dissolved inorganic sulfur species such as sulfite or thiosulfate. The results suggest the addition of Fe³⁺ at upstream locations would minimize the ferric salts required for achieving the same level of sulfide removal. Fe³⁺ dosing could also substantially reduce the formation of methane, a potent greenhouse gas, in sewers.     

固定化酶酸化反应器/UASB处理黄浆废水的研究

针对现有两相厌氧反应器微生物易流失以及单方面延长酸化相的停留时间导致的过酸化影响后续甲烷化过程的现象，开发了一套新型两相厌氧处理系统，其酸化相是采用大孔树脂固定化酶作生物载体的水解酸化反应器，产甲烷相则是接种了经长期驯化培养的高温厌氧污泥的UASB。采用该装置处理玉米加工过程中产生的富含蛋白质废水（黄浆废水），考察了进水COD浓度和负荷、C／N值等因素对系统处理效能的影响。结果表明：该装置运行稳定，在低C／N值和低负荷条件下，酸化相的酸化率（VFA／COD）即可达30％以上，其出水pH值稳定在6．7～7．0；产甲烷相对COD的去除率为91．3％，进水C／N值对产甲烷相去除COD有明显影响。     

以农田灌溉为目的的酒糟污水厌氧——脱硫处理新工艺

以试验为根据报导了采用高负荷上流式厌氧污泥床(UASB)反应器对酒糟污水进行中温(35℃)厌氧处理,厌氧出水进行空气氧化脱硫,最终出水用于农田灌溉的酒糟污水处理新工艺。试验还对UASB反应器中颗粒污泥的培养和高于中温时温度对UASB反应器工艺性能的影响作了较系统的研究。     

Sulfide removal in wastewater from petrochemical industries by autotrophic denitrification

An alternative flowchart for the biological removal of hydrogen sulfide from oil-refining wastewater is presented; autotrophic denitrification in a multi-stage treatment plant was utilized. A pilot-scale plant was fed with a mixture of the following constituents: (a) original wastewater from an oil refining industry (b), the effluent of the existing nitrification-stage treatment plant and (c) sulfide in the form of Na2S. Anoxic sulfide to sulfate oxidation, with nitrate as a terminal electron acceptor, proved very successful, as incoming concentrations of 110 mg S2-/L were totally converted to SO(4)2-. At complete denitrification, the concentration of S2- in the reactor effluent was less than 0.1mg/L. Fluctuating S2- concentration in the feed could be tolerated without any problems, as the accumulated sulfide in the effluent of the denitrification stage is oxidized aerobically in a subsequent activated-sludge treatment stage. This alternative new treatment scheme was further introduced at the refinery's wastewater processing plant. Thus, complete H2S removal is now accomplished by the combination of the proposed biological method and the existing stripping with CO2. As a result, stripping, and thus its cost, is reduced by 70%.     

Factors affecting removal of selenate in agricultural drainage water utilizing rice straw

Microbial reduction of selenate [Se(VI)] to elemental selenium [Se(0)] is a useful technique for removing Se from agricultural drainage water. A series of batch experiments were conducted in the laboratory to determine the effects of pH (5-10), NO(3)(-) (100-500 mg/l), and SO(4)(2-) (0-5000 mg/l) on the removal of Se(VI) from drainage water with 1000 microg/l of Se(VI) and different amounts (1-4 g) of rice straw. Results showed that rice straw was very effective in creating a reducing environment (Eh=-205 to -355 mV) in the first 3 days of the pH-effect experiments. The optimum conditions for rapid Se(VI) removal from drainage water were a pH range of 6-9, high amounts of SO(4)(2-) (1000-5000 mg/l), low amounts of NO(3)(-) (100 mg/l) and high amounts of rice straw (3-4 g). Under these conditions, it took 5-7 days to reduce 93-95% of the added Se(VI) to Se(0). This study indicates that rice straw may be an inexpensive reducing agent to remediate Se(VI)-dominant San Joaquin Valley drainage water in the field.     

A novel sulfate reduction, autotrophic denitrification, nitrification integrated (SANI) process for saline wastewater treatment

This paper reports on a lab-scale evaluation of a novel and integrated biological nitrogen removal process: the sulfate reduction, autotrophic denitrification and nitrification integrated (SANI) process that was recently proposed for saline sewage treatment. The process consisted of an up-flow anaerobic sludge bed (UASB) for sulfate reduction, an anoxic filter for autotrophic denitrification and an aerobic filter for nitrification. The experiments were conducted to evaluate the performance of the lab-scale SANI system with synthetic saline wastewater at various hydraulic retention times, nitrate concentrations, dissolved oxygen levels and recirculation ratios for over 500 days. The system successfully demonstrated 95% chemical oxygen demand (COD) and 74% nitrogen removal efficiency without excess sludge withdrawal throughout the 500 days of operation. The organic removal efficiency was dependent on the hydraulic retention time, up-flow velocity, and mixing conditions in the UASB. Maintaining a sufficient mixing condition in the UASB is important for achieving effective sulfate reduction. For a typical Hong Kong wastewater composition 80% of COD can be removed through sulfate reduction. A minimum sulfide sulfur to nitrate nitrogen ratio of 1.6 in the influent of the anoxic filter is necessary for achieving over 90% nitrate removal through autotrophic denitrifiers which forms the major contribution to the total nitrogen removal in the SANI system. Sulfur balance analyses confirmed that accumulation of elementary sulfur and loss of hydrogen sulfide in the system were negligible.     

UASB处理低浓度城市污水的生产性研究

广东某城市污水处理厂采用UASB-好氧工艺处理低浓度城市污水，对UASB的实际处理效能进行了考察。结果表明，在试验的进水水质条件下，当UASB的水力停留时间为6h时，系统对COD和BOD5的平均去除率分别为50％和60％，对TP的去除率为15％～38％。当HRT由5．67h延长至10h时，出水VFA浓度会随之降低，而pH值则始终稳定在6．5～7．5，系统对COD和BOD5的去除率分别增加9％和19％，对溶解性COD和BOD5的去除率分别增加25％和24％。     

Occurrence of methanogenesis during start-up of a full-scale synthesis gas-fed reactor treating sulfate and metal-rich wastewater

The start-up of a full-scale synthesis gas-fed gas-lift reactor treating metal and sulfate-rich wastewater was investigated. Sludge from a pilot-scale reactor was used to seed the full-scale reactor. The main difference in design between the pilot- and full-scale reactor was that metal precipitation and sulfate reduction occurred in the same reactor. After 7 weeks the full-scale reactor achieved the sulfate conversion design rate of 15 kg/m3day. Zinc sulfide precipitation inside the reactor did not interfere with obtaining a high rate of sulfate reduction. 16S rRNA gene analysis demonstrated that the bacterial communities in both reactors were dominated by the sulfate-reducing genus Desulfomicrobium. Archaeal communities of both reactors were dominated by the methanogenic genus Methanobacterium. Most Probable Number (MPN) counts confirmed that heterotrophic Sulfate-Reducing Bacteria (SRB) were dominant (10(11) -10(12) cells/g VSS) compared to homoacetogens (10(5) -10(6) cells/g VSS) and methanogens (10(8) -10(9) cells/g VSS). Methanogenesis was not suppressed during start-up of the full scale-reactor, despite the predominance of SRB, which have a lower hydrogen threshold. Due to the short sludge retention time (4-7 days) competition for hydrogen is determined by Monod kinetics, not hydrogen thresholds. As the kinetic parameters for SRB and methanogens are similar, methanogenesis may persist which results in a loss of hydrogen.     

Characterization of tributyltin in shipyard waters and removal through laboratory and full-scale treatment

Characterization and treatment studies were conducted in an effort to evaluate treatment options capable of removing tributyltin (TBT) in shipyard waters from above 1,000,000 ng/L to effluent concentrations below 50 ng/L. Laboratory studies and operation of a full-scale treatment plant were used to examine treatment options for TBT removal and included physicochemical treatment processes of coagulation-clarification, filtration, and granular activated carbon (GAC) adsorption. Significant variability was observed in TBT-containing shipyard waters (generated from different ships) in terms of their particulate solids, conductivity, and TBT and dissolved organic carbon concentrations. Laboratory tests with aluminum sulfate and ferric sulfate showed that on average 90% of TBT in shipyard waters could be removed by coagulation-flocculation-clarification under optimum conditions. No statistically significant difference was found in TBT removal capabilities between the two metal salts when compared at equivalent metal doses and coagulation pH. Much lower removals were observed for the coagulation-flocculation-clarification portion of the full-scale plant while the complete full-scale treatment plant averaged 99.8% TBT removal over a period of 3 years. While relatively high % removals were achieved, the total treatment process did not consistently remove TBT to levels that would meet the regulatory requirements proposed (50 ng/L) at the time the study was conducted. Based on the results from limited efforts to characterize the dissolved and particulate TBT fractions in the full-scale treatment plant effluent, particulate TBT was observed to be the dominant component of the effluent TBT from the full-scale plant and may be associated with polymer carry through.     

DEAMOX--new biological nitrogen removal process based on anaerobic ammonia oxidation coupled to sulphide-driven conversion of nitrate into nitrite

This paper reports about the successful laboratory testing of a new nitrogen removal process called DEAMOX (DEnitrifying AMmonium OXidation) for treatment of typical strong nitrogenous wastewater such as baker's yeast effluent. The concept of this process combines the recently discovered anammox (anaerobic ammonium oxidation) reaction with autotrophic denitrifying conditions using sulphide as an electron donor for the production of nitrite from nitrate within an anaerobic biofilm. To generate sulphide and ammonia, a Upflow Anaerobic Sludge Bed (UASB) reactor was used as a pre-treatment step. The UASB effluent was split and partially fed to a nitrifying reactor (to generate nitrate) and the remaining part was directly fed to the DEAMOX reactor where this stream was mixed with the nitrified effluent. Stable process performance and volumetric nitrogen loading rates of the DEAMOX reactor well above 1000 mgN/l/d with total nitrogen removal efficiencies of around 90% were obtained after long-term (410 days) optimisation of the process. Important prerequisites for this performance are appropriate influent ratios of the key species fed to the DEAMOX reactor, namely influent N-NO(x)/N-NH(4) ratios >1.2 (stoichiometry of the anammox reaction) and influent S-H(2)S/N-NO(3) ratios >0.57 mgS/mgN (stoichiometry of the sulphide-driven denitrification of nitrate to nitrite). The paper further describes some characteristics of the DEAMOX sludge as well as the preliminary results of its microbiological characterisation.