Effects of calcium on the microstructures and tensile properties of Mg-5Li-3Al alloys

The as-cast Mg-5Li-3Al-xCa (x = 0, 0.5, 1, 1.5 wt.%) was prepared with vacuum induction melting furnace, then processed by hot extrusion. The microstructures and tensile properties were investigated. The results show that the grains of as-cast alloys were refined gradually with the increase of Ca content from 0.5 wt.% to 1 wt.%, while the Ca content increases to 1.5 wt.%, the grain size increases. The microstructures of investigated alloys were further refined after hot extrusion. Both as-cast and as-extruded Mg-5Li-3Al-0.5Ca alloys have the highest mechanical properties, which is mainly attributed to the grain refinement caused by the addition of Ca and the formation of strengthening phase, Al₄Ca. When the addition of Ca is up to 1-1.5 wt.%, the tensile properties of alloys are worsened due to the excessive (Mg, Al)₂Ca eutectic phase forming at grain boundary.     

Microstructural refinement of Al-10.2%Si alloy by intensive shearing

Al-10.2%Si alloy when cast near the liquidus temperature has tremendous potential for producing fine grain structure. However, for casting applications, it requires casting at higher superheating, where this alloy results in large dendritic grain structure. Here, we show that, by applying intensive shearing to the liquid metal prior to casting, dendritic growth can be largely suppressed and fine grain structure can be achieved at higher casting temperature.     

Microstructural evolution and superplasticity of rolled Mg-9Al-1Zn

Microstructural evolution and superplasticity of a Mg-9Al-1Zn alloy rolled at 673 K were investigated at 573 K and 1.5×10⁻³ s⁻¹. The grain size of the as-rolled Mg alloy was 39.5 μm. However, the grain size of the specimen deformed to a true strain of 0.6 was 9.1 μm. The grain refinement was attributed to dynamically continuous recrystallization during an initial stage of tensile test. Stabilization of subgrain boundaries by fine particles and stimulation of continuous recrystallization by prior warm-deformation were not needed to attain dynamically continuous recrystallization in the Mg alloy. As a result of the grain refinement, the rolled Mg alloy exhibited superplastic behavior.     

An improved process for grain refinement of large 2219 Al alloy rings and its influence on mechanical properties

The large 2219 Al alloy rings used to connect propellant tank components of a satellite launch vehicle to each other are conventionally manufactured by radial-axial ring rolling at 460°C with 50% deformation,but often suffer from coarse elongated grain and low ductility. An improved process(hot ring rolling at460°C with 30% deformation, then air cooling to 240°C, followed by ring rolling at 240°C with 20% deformation) was tested for ring manufacturing. The corresponding microstructure evolution and mechanical properties of the produced rings were studied. The results show that the improved process can successfully be applied to manufacture the large 2219 Al alloy rings without formation of macroscopic defects,resulting in a product with fine and uniform grains after heat treatment. The fracture mechanism of both rings was mainly intergranular fracture. With the resulting grain size refinement due to the improved process, more homogeneous slip occured and the crack propagation path became more tortuous during the tensile testing process. Thus, the elongation in all three orthogonal directions was greatly improved,and the axial elongation increased from 3.5% to 10.0%.     

Texture and mechanical properties of ultrafine-grained Mg-3Al-1Zn alloy sheets prepared by high-ratio differential speed rolling

Mechanical properties and textures of the ultrafine grained (UFG) Mg-3Al-1Zn (AZ31) alloy with a mean grain size of 1 μm produced by high-ratio differential speed rolling were investigated. The resulting material exhibited high strength and relatively high ductility at ambient temperature. The high strength was attributed to grain-size and texture strengthening, while the high ductility was attributed to suppression of inhomogeneous twinning and increased strain-rate-sensitivity. The rolling temperature and the amount of shear strain accumulated during HRDSR affected the basal texture intensity and the rotation angle of the basal poles. Bimodal grain-size distribution obtained by annealing the UFG AZ31 at 573 K for a short time period resulted in considerable improvement of uniform elongation.     

Performance of AlTi5B1, AlTi3B3 and AlB3 master alloys in refining grain structure of aluminium foundry alloys

Abstract

The capacity of AlTi5B1, AlTi3B3 and AlB3 grain refiners to refine the grain structures of AlSi7Mg and AlSi11Cu2 foundry alloys was investigated. The performance of AlTi5B1, well established to be the best grain refiner for wrought aluminium alloys, is not nearly as good with the AlSi7Mg and AlSi11Cu2 alloys. Relatively smaller grains are obtained with the AlTi3B3 grain refiner in both alloys. The AlB3 grain refiner, on the other hand, improves the grain structure only as much as the AlTi5B1 grain refiner does. With as much as 0·04–0·1 wt-%Ti, the commercial alloys cannot enjoy the outstanding potency of the AlB₂ particles since the B supply is readily transformed to TiB₂ particles. However, the grains of the Ti free AlSi7Mg and AlSi11Cu2 alloys (～0·005 wt-%Ti) are very small and nearly globular for the entire range of holding times when inoculated with AlB3, implying not only a remarkable grain refining capacity but also a strong resistance to fading of the grain refinement effect. The lack of Ti in the melt allows the entire B to form AlB₂ particles, the perfect substrates to promote the nucleation of α-Al crystals. Aluminium castings can enjoy grain sizes well below 200 μm, with an addition of 0·02 wt-%B, provided that they are Ti free. That the potent substrates are made available just before the nucleation of α-Al crystals avoids fading effects and is a further advantage of the AlB3 grain refiner in recycling operations.     

Effect of grain refinement on mechanical properties and sliding wear resistance of extruded Sc-free 7042 aluminum alloy

The present study deals with an investigation on dry sliding wear behavior of grain refined Sc-free 7042 aluminum alloy by using a pin-on-disc wear test machine. Al–5Ti–1B and Al–15Zr master alloys were used as grain refining agents. The optimum amounts of added Ti and Zr in the alloy were found to be 0.03 wt.% and 0.3 wt.%, respectively. Extrusion was carried out and T6 heat treatment ware applied for all rod specimens before testing. Significant improvement in mechanical properties was obtained with the addition of grain refiners. The worn surfaces were characterized by energy dispersive X-ray spectrometry microanalysis. Results showed that the wear resistance of unrefined alloy increased with the addition of both grain refiners. Furthermore, the worn surface studies showed a mixed type of wear mechanisms; delaminating, adhesive and abrasive which took place at higher applied load.     

Grain refinement of AZ91 alloy by introducing ultrasonic vibration during solidification

Ultrasonic vibration was introduced into the solidification of AZ91 alloy. Various microstructures were produced in this alloy using ultrasonic vibrations at different temperatures of the melt. The coarse dendrite microstructures were obtained with ultrasonic vibrations at temperatures below the liquidus temperature. The fine uniform grains were achieved under ultrasonic vibrations during the nucleation stage, which was mainly attributed to the cavitation and the acoustic flow induced by the ultrasonic vibration.     

Mechanical properties and microstructural evolution of Al 6061 alloy processed by multidirectional forging at liquid nitrogen temperature

Al–Mg–Si alloy was subjected to multidirectional forging (MDF) at liquid nitrogen temperature (LNT), to cumulative strains of 1.8, 3.6 and 5.4. The deformed microstructures were examined by optical microscopy under polarized light and transmission electron microscopy (TEM). The deformed samples showed the formation of dislocation cells structure with high dislocation density at lower strains. Composite structure consisting of lamellar morphology at deformation bands and equiaxed grain morphology was observed. Significant differences in microstructure of the deformed samples were observed with increasing strain at LNT. At cumulative strain of 5.4, the microstructure shows nearly equiaxed subgrain structure with an average size of 250 nm with high angle grain boundaries. The mechanical properties were studied through Vickers hardness testing machine and tensile tester. The hardness value of MDFed alloy at LNT has increased from 50 Hv to 115 Hv for cumulative strain of 5.4. Tensile strength has increased from 180 MPa to 388 MPa with 4.5% percentage of elongation to failure. The improvement in hardness and tensile strength of forged alloy is attributed to the formation of equiaxed sub-grain structures and the presence of high dislocation density.     

The effect of chemical grain refinement and low superheat pouring on the structure of NRC castings of aluminium alloy Al–7Si–0.4Mg

The effect of the addition of Al–5Ti–1B (wt.%) chemical grain refiners on the nuclei generation for a range of superheats during pouring in new rheocasting (NRC) of aluminium alloy Al–7Si–0.4Mg (wt.%) has been investigated. The contributions to the grain density by the grain refiner additions and impurity particles were quantified and it was found that the addition of grain refiner provides increasing number of nucleation sites as the superheat is decreased from 105 to 35 °C. However, at superheats of 15 °C, which are more typical of NRC, the grain density is similar in the alloy both with and without grain refiner additions. At this superheat, the equiaxed grain morphology is globular rather than dendritic and it is postulated that the grain size is dependant upon grain coarsening mechanisms rather than the number of heterogeneous nucleation events. In agreement with previous studies on semi-solid processing, it was found that the achievement of a fine globular grain structure led to a more homogeneous casting being produced. The mechanism of the macrosegregation observed in these castings is discussed and explained by the ‘sponge effect’.     

碳和碱土元素复合细化对Mg-3Al合金抗拉强度的影响

利用碳和碱土金属(Ca和Sr)对Mg-3Al合金进行单独或复合细化处理,研究其品粒细化效果及其晶粒细化对Mg-3Al合金抗拉强度特性的影响规律.结果表明:0.2%C(质量分数,下同)、0.2%Ca及0.2%Sr均可显著细化Mg-3Al合金,而经0.2%C与0.2%Ca或0.2%Sr复合细化可进一步提高细化效果.细化后M...     

Grain refinement of biomedical Co-27Cr-5Mo-0.16N alloy by reverse transformation

Advanced grain refinement of a biomedical Ni-free Co-27Cr-5Mo-0.16N alloy without hot or cold plastic deformation was successfully achieved by a reverse transformation from a lamellar (hcp + Cr₂N) phase to an fcc phase. The technique consisted of a two-step heat treatment. First, the solution-treated specimen was subjected to isothermal aging at 1073 K for 90 ks, forming a lamellar structure of hcp and Cr₂N phases. Then, the aged specimen having a completely lamellar microstructure was reverse-treated at temperatures from 1273 to 1473 K, where the fcc phase is stable. The resultant grains were approximately 1/10 of their initial size. Moreover, tensile testing after reverse transformation showed excellent strength with good ductility compared to samples examined before the reverse transformation. Our results will contribute to the development of biomedical Ni-free Co-Cr-Mo-N alloys with refined grain size and good mechanical properties, without requiring any hot workings.     

Microstructural study of cold forged and annealed Mg alloys

Cold forging deformations (3 and 8%) were carried out on extruded AZ31 and AZ61 Mg alloys, and subsequent annealing is performed at 573?K for different durations. The microstructure evolution is investigated and further analysed. The results show that the thick lenticular twinning is mainly formed at initial deformation stage and subsequently transforms into narrow band twinning. Compared to AZ31, AZ61 produces broader twins with lower volume fraction in response to 3% cold forging due to Al–Mn phase hindering the twinning activity and plastic deformation. Twin boundary plays an important role in refining grains as it provides the nucleation sites of static recrystallisation. Moreover, as for AZ61, the starting and ending times of static recrystallisation are much later than those of AZ31.     

Effects of Al and Zn additions on mechanical properties and precipitation behaviors of Mg-Sn alloy system

For the Mg-Sn-Al alloys, the ultimate strength (UTS) of an extruded Mg-9wt.%Al-2wt.%Sn alloy reached 390 MPa. TEM observation indicated that plate-like Mg₁₇Al₁₂ precipitates having Burgers orientation relationship with the matrix are responsible for the strength. This alloy also exhibits an age hardening behavior: the peak hardness appears after 15-20 h of heat treatment at 473 K. On the other hand, the UTS of the Mg-Mg-Sn-Zn alloys are on the order of 300 MPa. The precipitates in these alloys are composed of the Mg₂Sn and MgZn₂ particles. It was found that these phases often precipitate together, suggesting that the MgZn₂ phase can act as a nucleation sites for Mg₂Sn.     

Microstructural evolution of aluminum alloy during friction stir welding under different tool rotation rates and cooling conditions

The microstructural evolution during friction stir welding (FSW) has long been studied only using one single welding parameter. Conclusions were usually made based on the final microstructure observation and hence were one-sided. In this study, we used the “take-action” technique to freeze the microstructure of an Al-Mg-Si alloy during FSW, and then systematically investigated the microstructures along the material flow path under different tool rotation rates and cooling conditions. A universal characteristic of the microstructural evolution including four stages was identified, i.e. dynamic recovery (DRV), dislocation multiplication, new grain formation and grain growth. However, the dynamic recrystallization (DRX) mechanisms in FSW depended on the welding condition. For the air cooling condition, the DRX mechanisms were related to continuous DRX associated with subgrain rotation and geometric DRX at high and low rotation rates, respectively. Under the water cooling condition, we found a new DRX mechanism associated with the progressive lattice rotation resulting from the pinning of the second-phase particles. Based on the analyses of the influencing factors of grain refinement, it was clearly demonstrated that the delay of DRV and DRX was the efficient method to refine the grains during FSW. Besides, ultra-high strain rate and a short duration at high temperatures were the key factors to produce an ultrafine-grained material.     

Effect of heating rate on the grain refinement of a TiAl alloy by cyclic heat treatment

This letter reports the effect of heating rate on the grain refinement of a Ti–46Al–2Cr–2Nb (at.%) alloy by cyclic heat treatment. Results show that microstructures with two different sizes were developed at two different heating rates. A coarse fully lamellar structure can be refined to a fine one with a size of 15 μm if the heating rate, together with the heating temperature, is appropriately controlled.     

A study on microstructure and mechanical properties of Al 6061-TiB2 in-situ composites

In situ reinforced aluminium based metal matrix composites (AMMCs) are emerging as one of the most promising alternatives for eliminating the inherent defects associated with ex situ reinforced AMMCs. Researchers in recent past have attempted various processing techniques for the development of in-situ composites, of which liquid metallurgy is the most widely adopted technique. Development of in-situ composites via liquid metallurgy route using master alloys is a relatively new processing technique. Very little information is available providing the usage value of these reinforcing materials.The present study is an attempt to explore the processing and characterization of in situ AMMCs using master alloys as reinforcement materials. Al 6061-TiB₂ in-situ composites were fabricated by liquid metallurgy route using Al 6061 as the matrix material and Al-10%Ti and Al-3%B as reactive reinforcements. Tests carried out on the fabricated composites include XRD, metallographic studies, EDAX analysis, microhardness, grain size analysis and tensile strength tests. The developed composites exhibited superior structural properties when compared with base alloy.     

Accelerated precipitation behavior of cast Mg-Al-Zn alloy by grain refinement

This study demonstrates that the precipitation behavior of β-Mg₁₇Al₁₂ phase during aging and the resultant variation in hardness and mechanical properties of cast Mg-Al-Zn alloy are strongly dependent on initial grain size. Grain size reduction accelerates discontinuous precipitation at the early stage of aging treatment by increasing the area fraction of grain boundaries that can act as nucleation sites for discontinuous precipitates (DP), but it does not influence DP growth rate. Grain refinement also prematurely terminates continuous precipitation because the formation of a large number of DP reduces the amount of Al dissolved in the matrix, which is required for the formation of continuous precipitates (CP). This promotion of DP formation and early termination of CP formation significantly decrease the peak-aging time to one-third. The enhanced precipitation behavior also leads to an additional hardness improvement in the aged alloy, along with an increase in hardness owing to grain boundary strengthening by grain refinement. The amount of increase in hardness changes with aging time, which is determined by the variation of three variables with aging time: DP fraction difference between refined and nonrefined alloys, hardness difference between DP and matrix, and matrix hardness difference between the two alloys. Grain refinement improves both tensile strength and ductility of the homogenized alloy owing to grain boundary strengthening and suppression of twinning activation, respectively. However, the loss of ductility after peak-aging treatment is greater in the refined alloy because of the larger amount of DP acting as a crack source in this alloy.     

Effect of Cu addition on microstructures and tensile properties of high-pressure die-casting Al-5.5Mg-0.7Mn alloy

In this study, Cu was added into the high-pressure die-casting Al-5.5Mg-0.7Mn (wt%) alloy to improve the tensile properties. The effects of Cu addition on the microstructures, mechanical properties of the Al-5.5Mg-0.7Mn alloys under both as-cast and T5 treatment conditions have been investigated. Additions of 0.5 wt%, 0.8 wt% and 1.5 wt% Cu can lead to the formation of irregular-shaped Al₂CuMg particles distributed along the grain boundaries in the as-cast alloys. Furthermore, the rest of Cu can dissolve into the matrixes. The lath-shaped Al₂CuMg precipitates with a size of 15–20 nm × 2–4 nm were generated in the T5-treated Al-5.5Mg-0.7Mn-xCu (x = 0.5, 0.8, 1.5 wt%) alloys. The room temperature tensile and yield strengths of alloys increase with increasing the content of Cu. Increasing Cu content results in more Al₂CuMg phase formation along the grain boundaries, which causes more cracks during tensile deformation and lower ductility. Al-5.5Mg-0.7Mn-0.8Cu alloy exhibits excellent comprehensive tensile properties under both as-cast and T5-treated conditions. The yield strength of 179 MPa, the ultimate tensile strength of 303 MPa and the elongation of 8.7% were achieved in the as-cast Al-5.5Mg-0.7Mn-0.8Cu alloy, while the yield strength significantly was improved to 198 MPa after T5 treatment.     

Microstructural evaluation of dross formation on Mg- and non-Mg-containing Al alloys from industrial furnaces

Abstract

The microstructural aspects of dross formation in industrial Al re-melt furnaces for several different alloy compositions have been evaluated. The Al alloys used in this study included 1350 (no Mg), 3004 (low Mg), and 5182 (high Mg). Dross specimens were collected directly from the different Al alloy melts in industrial furnaces using a consistent sampling protocol in order to compare the microstructure and phase development of the dross as a function of melt temperature and composition. The results showed that the sequence of phases formed during the re-melt process was the same for all the alloys examined; amorphous-Al₂O₃ forms first followed by either α-Al₂O₃+AlN (for non-Mg-containing alloys) or cubic MgO, then MgAl₂O₄, and lastly α-Al₂O₃ (for low- or high-Mg content). The formation of MgAl₂O₄ is associated with accelerated oxidation rates (known as breakaway oxidation) and this reaction proceeds until the Mg is depleted at the molten surface. At this point, aluminum oxidation is predominant and occurs at a significantly lower oxidation rate. The results obtained in this study are consistent with models developed for dross grown on similar Al alloys in laboratory environments and show that Mg oxidation (and the accelerated formation of MgAl₂O₄) dominates the oxidation process during Al melting, whether the Al contains low or high Mg contents. The oxide morphology within the dross layer differed according to the particular alloy being melted and thus the amount of Al recovery from dross can vary with composition.