Prediction model of carbonation depth for recycled aggregate concrete

The prediction of carbonation depth for recycled aggregate concrete (RAC) is investigated in this paper. The existing prediction models were evaluated, and it showed that the coefficient of variation (COV) of model error for the existing models is high. By introducing the weighed water absorption of aggregates, the COV of model error can be effectively decreased. Compared with the existing models, the proposed model can predict more accurate carbonation depths. For RAC specimens, compared with the fib model and Xiao and Lei's model-a, the COV of model error of the proposed model is 0.36 which is decreased by 33.3%, and when compared with Xiao and Lei's model-b and Silva et al.’s model, the corresponding decreases are 55.2% and 16.2%. Finally, the proposed model is validated by a 10-year-old carbonation experiment, which indicates that the proposed model is reasonable and can be applied to predict the carbonation depth of RAC.     

Durability of recycled aggregate concrete prepared with carbonated recycled concrete aggregates

The mechanical properties of recycled aggregate concrete (RAC) incorporating carbonated recycled concrete aggregates (RCAs) have previously been reported. However, the durability of RAC prepared with carbonated RCAs remains to be accessed. In this study, the durability properties of RAC prepared with non-carbonated RCAs and carbonated RCAs, in terms of deformation (drying shrinkage), water absorption and permeability (bulk electrical conductivity, gas and chloride ion permeability), are presented. The experimental results indicated that: (i) the incorporation of the carbonated RCAs in RAC not only helped to reduce the water absorption of RAC, but also reduced its permeability; (ii) when 100% carbonated NRCAs was used, the improvement extent of impermeability was 15.1%, 36.4% and 42.4% for bulk electrical conductivity, chloride ion permeability and gas permeability, respectively. Comparing the results of the mechanical and durability properties, the CO₂ curing treatment of RCAs had a greater beneficial impact on the durability properties of the RAC; and (iii) there was a good correlation between the water absorption of RAC and its permeability indicators. The water absorption value of RAC may be used as a criterion of the durability of RAC.     

高强再生骨料混凝土的配制及性能研究

采用再生粗骨料配制强度在50MPa或更大的高强再生骨料混凝土,并对其变形能力和耐久性进行测定,为高强再生骨料混凝土在工程上的应用提供理论和实验基础。通过一系列的抗压实验确定再生粗骨料的强度极限,并通过对水灰比的调整,使配制的高强再生骨料混凝土在强度上达到设计值,并以再生粗骨料取代率为0、30%、50%、80%和100%的高强再生骨料混凝土为研究对象进行实验。当再生粗骨料取代率为30%时,对再生混凝土的强度影响不大;之后混凝土强度随再生骨料的增加而降低。高强再生骨料混凝土与天然混凝土在耐久性上具有相似的性能,可以将高强再生混凝土应用于工程中。     

Bond strength prediction for deformed steel rebar embedded in recycled coarse aggregate concrete

This paper summarizes the results of an experimental investigation into the bond behavior between recycled aggregate concrete (RAC) and deformed steel rebars, with the main variables being the recycled coarse aggregate replacement ratio (RCAr) and water-to-cement ratio of the concrete mixture. The investigation into splitting cracking strength indicates that the degradation of the bond splitting tensile stress of the cover concrete was affected by not only the roundness of the coarse aggregate particles but also the weak interfacial transition zone (ITZ) between the cement paste and the RCA that has a more porous structure in the ITZ than normal concrete. In this study, a linear relationship between the bond strength and the density of the RCA was found, but the high compressive strength reduced the effects of the parameters. To predict the bond strength of RAC using the main parameters, a multivariable model was developed using nonlinear regression analysis. It can be inferred from this study that the degradation characteristic of the bond strength of RAC can be predicted well, whereas other empirical equations and code provisions are very conservative.     

Assessment of mechanical properties of concrete incorporating carbonated recycled concrete aggregates

An accelerated carbonation technique was employed to strengthen the quality of recycled concrete aggregates (RCAs) in this study. The properties of the carbonated RCAs and their influence on the mechanical properties of new concrete were then evaluated. Two types of RCAs, an old type of RCAs sourced from demolished old buildings and a new type of RCAs derived from a designed concrete mixture, were used. The chosen RCAs were firstly carbonated for 24 h in a carbonation chamber with a 100% CO₂ concentration at a pressure level of 0.1 Bar and 5.0 Bar, respectively. The experimental results showed that the properties of RCAs were improved after the carbonation treatment. This resulted in performance enhancement of the new concrete prepared with the carbonated RCAs, especially an obvious increase of the mechanical strengths for the concrete prepared with the 100% carbonated new RCAs. Moreover, the replacement percentage of natural aggregates by the carbonated RCAs can be increased to 60% with an insignificant reduction in the mechanical properties of the new concrete.     

再生骨料掺配比对再生透水混凝土性能的影响

为研究再生骨料在透水混凝土（RPC）中的应用,选用废弃路面素混凝土块为再生骨料来源,设计2种系列,研究再生骨料透水混凝土中再生骨料掺配问题,即分别以粒径9.5~19.0 mm,再生骨料按0%、25%、50%、75%和100%（基准）质量替代同粒径天然骨料碎石（系列1）和以4.75~9.5 mm、9.5~19.0 mm两种粒径,再生骨料按0∶1、1∶1、1∶2、2∶1、2∶3和3∶2掺比（系列2）制备RPC,并分析其物理、力学、透水性能及其相互关系,得到了合理的再生骨料替代率和双粒级掺比,在1∶1和2∶1掺配下能够得到较好的强度及透水性能。通过切割试块的图像化处理,分析其孔隙分布特征和趋势,并将平面孔隙率、等效孔径和透水系数联系起来。结果表明,再生透水混凝土的透水能力主要取决于截面孔隙个数和面积。     

Assessing relationships among properties of demolished concrete, recycled aggregate and recycled aggregate concrete using regression analysis

Recycled demolished concrete (DC) as recycled aggregate (RA) and recycled aggregate concrete (RAC) is generally suitable for most construction applications. Low-grade applications, including sub-base and roadwork, have been implemented in many countries; however, higher-grade activities are rarely considered. This paper examines relationships among DC characteristics, properties of their RA and strength of their RAC using regression analysis. Ten samples collected from demolition sites are examined. The results show strong correlation among the DC samples, properties of RA and RAC. It should be highlighted that inferior quality of DC will lower the quality of RA and thus their RAC. Prediction of RAC strength is also formulated from the DC characteristics and the RA properties. From that, the RAC performance from DC and RA can be estimated. In addition, RAC design requirements can also be developed at the initial stage of concrete demolition. Recommendations are also given to improve the future concreting practice.     

基于需水量比和强度比的再生粗骨料分类方法

我国尚无再生骨料的技术标准,因此,研究再生粗骨料分类方法、制定再生粗骨料的技术标准,对于推动再生混凝土产业化具有重要意义.通过对再生粗骨料与普通粗骨料制备的混凝土工作性和强度的试验研究,首次提出了需水量比和强度比的概念,并给出了相应的试验方法.结果表明,需水量比和强度比两项指标能够很好地反映再生粗骨料与普通粗骨料之间的性能差异.基于上述指标,可将再生粗骨料分成3个等级,以保证再生混凝土满足在不同领域应用的性能要求.     

不同土工合成材料与再生混凝土骨料界面动剪切特性研究

针对研究5种不同土工合成材料与再生混凝土骨料(RCA)之间的界面循环剪切及后直剪特性,在不同法向应力与循环剪切幅值条件下进行了一系列单调直剪(MDS)、循环直剪(CDS)、后循环直剪(PCDS)试验,并综合对比分析了后循环直剪与单调直剪试验结果.试验结果表明,在循环直剪作用下,5种筋-土界面呈现出明显的剪切硬化现象,剪...     

Influence of steam curing on the pore structures and mechanical properties of fly-ash high performance concrete prepared with recycled aggregates

In this research work, High Performance Concrete (HPC) was produced employing 30% of fly ash and 70% of Portland cement as binder materials. Three types of coarse recycled concrete aggregates (RCA) sourced from medium to high strength concretes were employed as 100% replacement of natural aggregates for recycled aggregate concrete (RAC) production. The specimens of four types of concretes (natural aggregate concrete (NAC) and three RACs) were subjected to initial steam curing besides the conventional curing process. The use of high quality RCA (>100 MPa) in HPC produced RAC with similar or improved pore structures, compressive and splitting tensile strengths, and modulus of elasticity to those of NAC. It was determined that the mechanical and physical behaviour of HPC decreased with the reduction of RCA quality. Nonetheless steam-cured RACs had greater reductions of porosity up to 90 days than NAC, which led to lower capillary pore volume.     

颗粒整形对再生粗骨料性能的影响

为了有效提高再生粗骨料的性能,必须对再生骨料进行机械强化处理.首次提出了利用高速(线速度≥80m/s)运动的再生骨料之间的反复相互冲击与摩擦作用,有效地打掉较为突出的棱角和除去颗粒表面附着的砂浆和水泥石的一种新技术.研究表明:颗粒整形使再生骨料的颗粒堆积密度平均提高了9.3%、表观密度从2.56g/cm3提高到2.59g/cm3、空隙率从53.3%降至48.5%、吸水率从4.7%降至2.9%、压碎指标值从15.8%降至9.4%,而且堆积密度、密实密度和针片状骨料含量等指标均优于天然碎石骨料,完全能够满足配制普通混凝土的要求.     

Evaluation of the stress-strain behavior of confined recycled aggregate concrete under monotonic dynamic loadings

Recycled aggregate concrete (RAC) has been attracting worldwide research interests due to its ecological and economic significance. However, RAC has so far mainly been limited to non-structural applications or structural members subjected to static loadings. In this study, the effects of strain rates, the confinement, and the RCA replacement ratio on the mechanical behaviors of confined recycled aggregate concrete (CRAC) are investigated through dynamic tests. The corresponding dynamic increase factor (DIF), confining increase factor (CIF) and replacement ratio influence factor (RIF) are formulated. A constitutive model for CRAC is then proposed through applying DIFs, CIFs, and RIFs to the characteristic parameters. Finally, the predicted stress-strain relationships of test samples using the proposed constitutive model are compared and evaluated with the experimental results. It is concluded that the proposed constitutive model can be applied to the further dynamic nonlinear analysis of RAC structures.     

Impact of particle packing mix design method on fracture properties of natural and recycled aggregate concrete

The fracture properties of four types of concrete prepared using natural coarse aggregate and recycled coarse aggregate and conventional and particle packing method (PPM) of mix design approaches are studied. The three‐point bending (TPB) test is performed using three different sizes of single edge notched beam. The fracture energy is calculated from the load‐CMOD curve obtained in the TPB test, and in this process the load‐CMOD curve is curtailed at 2% of the depth of the beam. Based on CTOD_c and w₁ relationship, appropriate softening function is used to estimate the double‐K fracture parameters. The fracture energy and fracture toughness parameters of recycled aggregate concrete (RAC) is inferior to the natural aggregate concrete (NAC). The PPM mix design improves the fracture properties of concrete in comparison to the conventional mix design approach. The fracture properties of PPM mix designed RAC are comparable to that of NAC prepared using conventional method.     

再生混凝土动态直接拉伸的试验研究

利用大直径(75 mm)分离式霍普金森拉杆(SHTB),对再生粗骨料取代率分别为0%、25%、50%、75%和100%的5组圆柱体再生混凝土试样进行应变率范围为100~102s-1的动态直接拉伸实验,研究再生混凝土的动态直接拉伸力学性能及其破坏形态。试验结果表明,再生混凝土的抗拉强度随平均应变率的增加而增大,而再生混凝土的破坏形态与平均应变率有关,这表明再生混凝土具有明显的率敏感性。在相同水灰比下,再生混凝土准静态拉伸强度比普通混凝土低1.3%~15.9%,动态拉伸强度比普通混凝土低1.7%~29%,此研究为再生混凝土的工程应用提供一定的理论依据。     

Biphasic carbonation behaviour of structural lightweight aggregate concrete produced with different types of binder

This study aims to characterise the carbonation behaviour of structural lightweight aggregate concrete (SLWAC) produced with different types of aggregate, w/c ratios and types and content of mineral admixtures (silica fume, fly ash, lime filler) by means of accelerated carbonation tests. A new biphasic model to describe the carbonation behaviour of SLWAC is suggested. Based on this model, the carbonation coefficient of SLWAC is estimated as a function of the w/c ratio, for different density classes of lightweight aggregates. It is concluded that the carbonation resistance of SLWAC cannot be properly predicted by its compressive strength and that the carbonation rate is little affected by the type of binder, being appropriate to neglect the contribution of mineral admixtures in carbonation resistance of SLWAC. It is also concluded that even with pastes of moderate quality, the carbonation mechanism should not be relevant to the durability of SLWAC.     

多因素对再生混凝土力学性能及抗冻性的影响

为研究不同因素、不同水平对再生混凝土力学性能的作用。该文通过正交试验研究钢纤维掺量、再生粗骨料掺量和粉煤灰掺量对再生混凝土力学性能(抗压强度、劈裂抗拉强度和抗折强度)的影响,确定各因素对再生混凝土力学性能的影响程度,并加以量化表征,并提出多因素共同作用下再生混凝土力学性能的多元非线性回归模型且进行验证。在此基础上,该文进一步研究再生混凝土的抗冻性。结果表明:再生混凝土的力学性能随钢纤维掺量的增加而提高;随粉煤灰掺量增加而降低;再生粗骨料掺量对再生混凝土的力学性能影响较小。钢纤维的掺入可提高再生粗骨料的掺量。再生混凝土力学性能的实测值与通过建立的回归模型得到的计算值的最大误差在6.5%以内。此外,钢纤维的掺入和减少再生粗骨料的掺量均可以提高再生混凝土的抗冻性。     

Evaluation of the bond behavior of steel reinforcing bars in recycled fine aggregate concrete

This paper describes pullout test results on deformed reinforcing bars in natural and recycled fine aggregate (RFA) concrete. The effects of bar location and RFA grade on bond strength between reinforcing bar and recycled aggregate concrete (RAC) were evaluated through the experimental program. A total of 150 pullout specimens were fabricated for the experiment. Two reinforcing bar orientations were considered with respect to the casting direction; vertical bars and horizontal bars, the latter of which was prepared to evaluate top-bar effect. Considered variables included four RFA replacement ratios (RFArs), two water-absorption grades (RFA-A: 5.83%, RFA-B: 7.95%) of RFA and three reinforcing bar locations (75, 225 and 375 mm height from the bottom of the casting mold). In addition, to evaluate the thermal and aging effect on bond behavior between the reinforcing bar and RFA concrete, some parts of pullout specimens had exposed to rapid freeze–thaw environment or been cured at air during 28 or 730 days. Test results demonstrated that bond strength does not seem to be affected by the RFAr for higher RFA grades (RFA-A), at least up to 60% RFAr. In contrast, the RAC including lower RFA grade (RFA-B) showed clear decreases in bond strength with increasing RFAr, similar to the trend observed for compressive strength. For horizontal pullout specimens, RFA concrete specimens showed higher bond strength gap between top and bottom bars than natural aggregate concrete (NAC) specimens. Bond strengths of the horizontally cast pullout specimens were affected by the flowability of concrete rather than the RFAr or RFA grade. No noticeable degradation occurred during freeze–thaw cycling of the RAC specimens, indicating that the RFA used in this study is appropriate for use in freeze–thaw environments.     

Impact performances of steel tube-confined recycled aggregate concrete (STCRAC) after exposure to elevated temperatures

The impact behaviours of steel tube-confined recycled aggregate concrete (STCRAC) following exposure to elevated temperatures of 20 °C, 200 °C, 500 °C and 700 °C were experimentally investigated using a 100 mm-diameter split Hopkinson pressure bar (SHPB). The recycled coarse aggregate (RCA) replacement ratios were set as 0, 50% and 100%. The effect of RCA replacement ratio and exposure temperature on the impact properties of STCRAC were analysed in terms of failure modes, stress-strain time history curve and dynamic increase factor (DIF). The results show that the fire-damaged STCRAC can maintain its integrity during impact load. However, there were evident degradations in the dynamic behaviour of STCRAC after exposure to high temperatures of 500 °C and 700 °C. The ultimate impact strength, impact secant modulus and residual impact strength of STCRAC obviously decreased because of the damage due to high temperature exposure. But the degradations of both the ultimate impact strength and impact secant modulus of STCRAC under impact loading were less severe than those under quasi-static loading. The remaining strength factor and the DIF tended to increase with the raise of the elevated temperatures. Overall, during the impact loading, the fire-deteriorated STCRAC exhibited excellent impact behaviour.     

Base force element method based on the complementary energy principle for the damage analysis of recycled aggregate concrete

The finite element method (FEM) is an effective approach for exploring the failure mechanism of heterogeneous materials. According to the complementary energy principle, the use of FEM might suffer from several difficulties in terms of keeping the elements and their boundaries balanced, as well as finding interpolation functions. In this study, we introduced an efficient approach to researching the failure mechanism of the material, named base force element method (BFEM), according to complementary energy principle. Specifically, the element compliance matrix of an arbitrary quadrilateral element with four mid-edge nodes was expressed based on the complementary energy principle. Then, the node displacement was obtained by the governing equation using the Lagrange multiplier method. In addition, both the compliance matrix and the node displacement were represented as explicit expressions without the use of Gaussian integration. A numerical model of the recycled aggregate concrete (RAC) was established according to the Monte Carlo method. A comparative sample of the digital image model was also established using digital image technology. The influences of substituting recycled aggregate and the relative mechanical properties of adhered mortar to those of new mortar on the failure mechanism of RAC were studied. The simulation results indicated that the BFEM is an effective approach to researching the damage mechanism of heterogeneous materials.     

A comprehensive investigation into the effect of aging and coarse aggregate size and volume on mechanical properties of self-compacting concrete

The popularity of self-compacting concrete (SCC), as an innovative construction materials in concrete industry, has increased all over the world in recent decades. SCC offers a safer construction process and durable concrete structure due to its typical fresh concrete behavior which is achieved by SCC’s significantly different mixture composition. This modification of mix composition may have significant effect on the hardened mechanical properties of SCC as compared to normal vibrated concrete (NVC). Therefore, it is necessary to know whether the use of all rules and relations that have been formulated for NVC in current design codes based on years of experience are also valid for SCC. Furthermore, this study represents an extensive evaluation and comparison between mechanical properties of SCC using current international codes and prediction equations proposed by other researchers. Thus, in this experimental study, major mechanical properties of SCC are investigated for twelve SCC mixes with wide spectrum of different variables i.e. maximum coarse aggregate size, coarse aggregate volume and aging. In the present study, an extensive body of data reported by many researchers for SCC and NVC has been used to validate the obtained results.