Air-stable triarylamine-based amorphous polymer as donor material for bulk-heterojunction organic solar cells

A new air-stable triarylamine-based amorphous polymer, TSP-T11, which consists of thiophene and triarylamine units, can be successfully utilized to fabricate bulk-heterojunction organic photovoltaics (OPVs) using PC₆₀BM or PC₇₀BM as acceptor materials. The highest level of performance of OPVs optimized at TSP-T11:PC₇₀BM (weight ratios of 1:4) with thicknesses of 68 nm exhibited an open circuit voltage (V_oc) of 0.75 V, a short circuit current (J_sc) of 8.03 mA cm⁻², and a power-conversion efficiency (PCE) of 2.22% under simulated air mass 1.5 solar irradiation at 100 mW cm⁻². Although TSP-T11 has a lower hole mobility (1.5×10⁻⁴ cm² V⁻¹ s⁻¹) than P3HT, the use of amorphous film of TSP-T11 as a donor material for OPVs offers advantages over the use of polycrystalline film of P3HT in terms of its air-stability and pinhole-free homogeneous morphology.     

P3HT/TiO2 bulk-heterojunction solar cell sensitized by a perylene derivative

In this work, a new type of dye-sensitized bulk-heterojunction hybrid solar cells has been developed. The heterojunction films were prepared to contain poly(3-hexylthiophene) (P3HT), N,N′-diphenyl glyoxaline-3,4,9,10-perylene tetracarboxylic acid diacidamide (PDI) and TiO₂. In the architecture, TiO₂ and P3HT were designed to act as the electron acceptor and donor. PDI was used as sensitizer to enhance the photon absorption. Results showed that by incorporation of PDI in the P3HT/TiO₂ composite, the light absorption, exciton separation and photocurrent under white light were dramatically enhanced. Solar decay analyses showed that devices contained TiO₂ required 12 h to obtain maximum current density and the addition of PDI did not affect the solar decay behavior and stability of device composed of P3HT/TiO₂. The devices of P3HT, P3HT/TiO₂, P3HT/TiO₂/PDI could work for 5, 42, 45 h under continuous white light illumination (100 mW/m²) under the ambient condition.     

Flexible large area polymer solar cells based on poly(3-hexylthiophene)/fullerene

Photovoltaic devices based on regioregular poly(3-hexylthiophene) (P3HT) and ([6,6]-phenyl-C61-butyric acid methyl ester) (PCBM) were fabricated and characterized using 5×5 cm ITO polyester foils with an active cell area of 0.5×0.5 cm². The HOMO/LUMO of P3HT and PCBM were estimated from cyclic voltammetry data. The complete quenching of photoluminescence of P3HT after mixing with PCBM indicates an effective charge transfer from P3HT to PCBM. The absorption spectrum of a blend (1:3 wt%) of both components shows that there is no ground state doping. Following device parameters without any special postproduction treatment were determined: V_OC=600 mV, I_SC=6.61 mA/cm², FF=0.39 and η_AM1.5 (P_IN:100 mW/cm²)=1.54%.     

Effect of solution processed graphene oxide/nickel oxide bi-layer on cell performance of bulk-heterojunction organic photovoltaic

We report the solution processed graphene oxide (GO), NiO_x and GO/NiO_x bi-layer used as an anode interfacial layer in organic bulk-heterojunction solar cells. The bulk-heterojunction solar cells using GO, NiO_x and GO/NiO_x bi-layer exhibited the conversion efficiency of 2.33%, 3.10% and 3.48%, respectively. The cell efficiency is correlated with the matching of energy levels between ITO, hole transport layer and P3HT and thus a well-matched stack layer of ITO/GO/NiO_x/P3HT:PCBM/LiF/Al shows the best cell efficiency of 3.48% with the J_SC of 8.71 mA/cm², V_OC of 0.602 V and FF of 66.44%.     

Electrodeposition zinc-oxide inverse opal and its application in hybrid photovoltaics

This article reports the preparation of three-dimensional (3D) mesoporous zinc oxide (ZnO) films and their application in solar cells. The films were obtained through electrochemical deposition in DMSO solutions by using PS colloidal crystal as templates. The ZnO films with inverse opal (IO) structure were obtained after removing the templates by thermolysis. The ordered porous ZnO films were used to prepare hybrid solar cells by infiltrating the films with poly(3-hexylthiophene) (P3HT) or P3HT:ZnO nanocomposite. Results showed that the interpenetrating network of both ZnO(IO) and P3HT can form continuous pathways for electron and hole transport. By infiltrating a P3HT:ZnO nanocomposite into the porous ZnO films, the photocurrent of the solar cell can be dramatically improved. The cell shows the V_oc and I_sc of 462 mV and 444.3 μA/cm², respectively. By using a 420 nm cutoff filter, the cell retains about 80% and 50% of its original V_oc and I_sc after continuous white-light illumination (100 mW/cm²) for 10 h. Stability of the device under above conditions was estimated to be 51 h.     

Widening of harvesting layer and area of P3HT/PCBM bulk-heterojunction photovoltaic cells

We have fabricated P3HT/PCBM based bulk-heterojunction photovoltaic cells with P3HT layer as the hole transport layer and PCBM layer as the electron transport layer between electrode and blended P3HT/PCBM layer in order to widen the photon harvesting layer. Current density has increased by about 1 mA/cm² by the insertion of P3HT layer and the resulting conversion efficiency has been improved by about 20%. We have also fabricated a centimeter-scale active area with an efficiency of ∼1%.     

Characterization of N, N′-bis-2-(1-hydoxy-4-methylpentyl)-3, 4, 9, 10-perylene bis (dicarboximide) sensitized nanocrystalline TiO2 solar cells with polythiophene hole conductors

We have fabricated solid-state, dye-sensitized nanocrystalline TiO₂ solar cells (DSSC) based on perylene derivative dye, N,N′-bis-2-(1-hydoxy-4-methylpentyl)-3,4,9,10-perylene bis (dicarboximide) (HMPER) with two different polythiophenes as hole conductors; i.e. poly (3-octyl thiophene) (P3OT) and poly (3-hexyl thiophene) (P3HT), respectively. HMPER adsorbs strongly to the surface of nanocrystalline TiO₂ and inject electrons into TiO₂ conduction band upon absorption of light. Polythiophene derivatives are well-known materials as hole conductors in solid-state dye-sensitized solar cells. We obtained quite similar results with P3OT and P3HT yielding a short-circuit current density of around 80 μA/cm² and open-circuit voltage of around 0.7 V at 80 mW/cm² AM 1.5 light intensity. The results are compared with Ru-535 TBA-sensitized nc-TiO₂ cells prepared by using the same polythiophene derivatives.     

Synthesis and photovoltaic properties of biindene-C70 monoadduct as acceptor in polymer solar cells

A new fullerene derivative, biindene-C₇₀ monoadduct (BC₇₀MA), was synthesized by [4+2] cycloaddition reaction between 1,1′-biindene and C₇₀, for the application as acceptor in polymer solar cells (PSCs). BC₇₀MA is soluble in common organic solvents such as tetrahydrofuran, chloroform, toluene, o-dichlorobenzene, etc., and shows stronger absorption in the visible region and a slightly up-shifted lowest unoccupied molecular orbital (LUMO) energy level than that of PCBM. PSCs were fabricated with BC₇₀MA as acceptor and poly(3-hexylthiophene) (P3HT) as donor for investigating the photovoltaic properties of BC₇₀MA. The power conversion efficiency of the PSC based on P3HT/BC₇₀MA (1:1, w/w) with the additive of 3% octane-1,8-dithiol and thermal annealing at 110 °C for 10 min reached 3.44% with open circuit voltage of 0.64 V, short circuit current of 8.02 mA/cm² and fill-factor of 0.67, under the illumination of AM1.5, 100 mW/cm².     

Enhancing the short-circuit current and efficiency of organic solar cells using MoO3 and CuPc as buffer layers

Efficient bulk-heterojunction (BHJ) (regioregular poly (3-hexylthiophene) (P3HT): (6, 6)-phenyl C₆₁ butyric acid methyl ester (PCBM)) solar cells were fabricated with molybdenum trioxide (MoO₃) and copper phthalocyanine (CuPc) as buffer layers. The insertion of MoO₃ layer was found to be critical to the device performance, effectively extracting holes to prevent the exciton quenching and reducing the interfacial resistance because of alignment of energy levels. The introduction of CuPc buffer layer was observed to be ameliorative for device performance, further enlarging the visible absorption spectra range of the devices. The effect of the MoO₃ and CuPc layer thickness on device performance was studied. The optimized thickness was achieved when MoO₃ layer was 12 nm and CuPc layer was 6 nm, resulting in optimized power conversion efficiency (PCE) of 3.76% under AM1.5G 100 mW/cm² illumination.     

Efficiency enhancement of polymer solar cells by incorporating a self-assembled layer of silver nanodisks

We report the efficiency enhancement of polymer solar cells by incorporating a silver nanodisks' self-assembled layer, which was grown on the indium tin oxide (ITO) surface by the electrostatic interaction between the silver particles and modified ITO. Polymer solar cells with a structure of ITO (with silver nanodisks)/poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) (Clevious P VP AI 4083)/poly(3-hexylthiophene):[6,6]-phenyl-C61 butyric acid methyl ester (P3HT:PC₆₁BM)/LiF/Al exhibited an open circuit voltage (V_OC) of 0.61±0.01 V, short-circuit current density (J_SC) of 9.24±0.09 mA/cm², a fill factor (FF) of 0.60±0.01, and power conversion efficiency (PCE) of 3.46±0.07% under one sun of simulated air mass 1.5 global (AM1.5G) irradiation (100 mW/cm²). The PCE was increased from 2.72±0.08% of the devices without silver nanodisks to 3.46±0.07%, mainly from the improved photocurrent density as a result of the excited localized surface plasmon resonance (LSPR) induced by the silver nanodisks.     

High-performance polymer photovoltaic devices with inverted structure prepared by thermal lamination

Use of a lamination process for the introduction of Au electrode, instead of conventional metal evaporation, improved the power conversion efficiency (PCE) of inverted-structure photovoltaic devices from 1.6% to 2.6% based on a bulk heterojunction of poly(3-hexylthiophene) (P3HT) and (6,6)-phenyl C₆₁ butyric acid methyl ester (PCBM). X-ray photoelectron spectroscopy indicated that a thin layer of P3HT is spontaneously formed at the air/polymer blend layer interface during the spin-coating process. It is suggested that the vacuum-evaporated gold could destroy the surface-segregated thin layer of P3HT, while the lamination process preserves the surface structure working as an electron-blocking layer. The insertion of a PEDOT:PSS layer, between the metal electrode and polymer layer, in the lamination process further improved the PCE to 3.3% with a short-circuit current density of 9.94 mA cm⁻², an open-circuit voltage of 0.60 V, and a fill factor of 55% under AM1.5 100 mW cm⁻² irradiation.     

Molecular engineering of Diketopyrrolopyrrole-based photosensitizer for solution processed small molecule bulk heterojunction solar cells

New symmetrical low band-gap small molecule materials, DPP-bis[ter-3HT-TPA] and DPP-bis[ter-3HT] as novel derivatives of Diketopyrrolopyrrole-thiophene with/without triphenylamine (TPA) end group have been synthesized and characterized. And the effects of TPA moiety were investigated. Compared to DPP-bis[ter-3HT], DPP-bis[ter-3HT-TPA] shows red-shifted absorption and significantly higher molar absorption coefficient. And the HOMO level of DPP-bis[ter-3HT-TPA] is elevated than DPP-bis[ter-3HT]. Moreover, DPP-bis[ter-3HT-TPA] exhibited one order higher hole mobility than DPP-bis[ter-3HT], suggesting that TPA contributes to a better hole mobility. The bulk-heterojunction photovoltaic devices with DPP-bis[ter-3HT-TPA] showed better efficiencies than DPP-bis[ter-3HT], showing the best power-conversion efficiency (PCE) of 1.5% (±0.12) under 100 mW/cm² with a short-circuit current (J_sc)=5.73 mA/cm², a fill factor (FF)=0.45, and an open-circuit voltage (V_oc)=0.59 mV.     

Efficient hybrid carboxylated polythiophene/nanocrystalline TiO2 heterojunction solar cells

Efficient hybrid solar cells fabricated from TiO₂, novel carboxylated polythiophene poly (3-thiophenemalonic acid) P3TMA as sensitizer as well as hole conductor and poly (3-hexylthiophene) (P3HT) as hole transporter was described. UV-Vis absorption and morphology of the active layer were investigated. Device J/V characterizations with different P3HT layer thickness were measured and discussed. Efficiency improvements were observed in thinner P3HT layer thickness and with poly[3,4-(ethylenedioxy)-thiophene]:poly(styrene sulfonate) (PEDOT:PSS) as charge collection layer, and such device showed a short-circuit current density of 1.32 mA/cm², an open-circuit voltage of 0.44 V, a fill factor of 0.43, and a energy conversion efficiency of 0.25% at A.M. 1.5 solar illumination (100 mW/cm²).     

Facile SILAR preparation of Fe(OH)3/Ag/TiO2 nanotube arrays ternary hybrid for supercapacitor negative electrode

The ternary hybrid composite electrode of Fe(OH)₃/Ag/TNTA (where TNTA stands for TiO₂ nanotube arrays) was prepared by a simple successive ionic layer adsorption and reaction method. The effects of calcination temperature of Ag/TNTA, drying temperature of Fe(OH)₃/Ag/TNTA, and deposition amount of Ag and Fe(OH)₃ on the supercapacitor performance of the composite electrode were investigated, and the related reasons were discussed in detail. The results show that Ag modification can obviously improve the performance of Fe(OH)₃/TNTA composite electrode. Both the calcination temperature of Ag/TNTA and the deposition amount of Ag affect the particle size of Ag and the reaction resistance of the electrode. The deposition amount of Fe(OH)₃ also has influence on the reaction resistance of the electrode. Under the optimized conditions, the capacitance value of the Fe(OH)₃/Ag/TNTA composite electrode is as high as 84.67 mF cm^?2@5 mV s^?1（596.30 F g^?1@5 mV s^?1）, and the electrode has high rate performance and good cycle stability. The asymmetric supercapacitor assembled with Fe(OH)₃/Ag/TNTA as the negative electrode and activated carbon as the positive electrode can store energy stably under the potential window of 0–1.5 V. When the power density is 2.77 kW kg^?1 (50 mW cm^?3), the energy density can reach 18.34 Wh kg^?1 (0.33 mWh cm^?3).     

Improving the current density Jsc of organic solar cells P3HT:PCBM by structuring the photoactive layer with functionalized SWCNTs

Several works concerning the incorporation of carbon nanotubes (CNTs) in bulk polymer RR-P3HT (regio-regular poly(3-hexylthiophene-2,5-diyl)):PCBM (methanofullerene phenyl–C₆₁–butyric-acid–methyl-ester) heterojunction have been already reported by a number of research groups. The optical and electrical properties of organic cells have been extensively studied. We investigated the incorporation of functionalized single wall carbon nanotubes (SWCNTs) into the matrix of P3HT:PCBM photovoltaic (PV) cells. The photovoltaic characteristics of the cells depend on the concentration of SWCNT. The incorporation of low concentrations of SWCNT in the photoactive layer increases the current density J_sc before annealing and it can reach above 9 mA/cm². We attribute the improved PV performances to partial crystallization of the RR-P3HT. As revealed by XRD studies and confirmed by the absorbance spectra, which exhibit the typical shoulder at 600 nm and absorbance in the near infrared region. Interestingly, we observe also that doping the P3HT:PCBM active layer by the functionalized SWCNTs increases the open circuit voltage V_oc.     

Bulk-heterojunction photovoltaic devices based on donor–acceptor organic small molecule blends

We present a systematic study on photovoltaic devices that combine an organic small molecule photoactive donor–acceptor bulk heterojunction system with controlled doping of the charge transport layers. The doped transport layers are formed using high vacuum co-evaporation deposition technique (i.e. co-sublimation of matrix and dopant). Solar cell devices have been fabricated based on zinc-phthalocyanine (ZnPc) as donor (D) and fullerene (C₆₀) as electron acceptor (A) with doped charge transport layers. The cells show a short circuit current, I_sc=1.5 mA/cm², an open circuit voltage, V_oc=450 mV, a fill factor, FF=0.5, and a power conversion efficiency, η_e=3.37% under sun (10 mW/cm²) white light illumination. In addition, these bulk-heterojunction photovoltaic devices were characterized under 1 sun (100 mW/cm²) white light illumination showing I_sc=6.3 mA/cm², V_oc=500 mV, and η_e=1.04%. We have observed that the performance of such ‘bulk-heterojunction’ photovoltaic devices is critically dependent on the transport properties of the interpenetrating network D/A system and doped charge transport layers.     

Improving the efficiency of organic solar cell with a novel ambipolar polymer to form ternary cascade structure

This study describes the utilization of a novel conjugated copolymer, namely, poly[2,3-bis(thiophen-2-yl)-acrylonitrile-9,9′-dioctyl-fluorene] (FLC8) for organic solar cell application for the first time. The highest occupied molecular orbital and the lowest unoccupied molecular orbital of FLC8 are −5.68 and −3.55 eV, respectively, which lie between the corresponding values of poly(3-hexylthiophene) (P3HT) and [6,6]-phenyl-C61-butyric acid methylester (PCBM). In addition, both electron and hole mobilities of FLC8 are in the range of 10⁻⁴ (cm²/V s), making it an excellent ambipolar polymer. Such unique properties make FLC8 a good candidate to form a ternary cascade bulk-heterojunction organic solar cell when blending with P3HT and PCBM. The power conversion efficiency (PCE) of the ternary cascade solar cell can be increased by up to 30% as compared with the reference cell without FLC8. We suspect that this enhancement of PCE is caused by the additional charge separation offered by the cascade structure and the fast charge transfer due to the ambipolarity of FLC8.     

Investigation of multi-donor bulk-heterojunction photovoltaic cells based on P3HT:PCBM system

(2,7-bis[5′-(9,9-dioctylfluorene-2-yl)-2,2′-dithienyl-5-yl]-9,9-dioctylfluorene) (F3Th4) was used as a secondary electron donor material in the poly(3-hexylthiophene) (P3HT):[6,6]-phenyl C61-butyric acid methyl ester (PCBM) bulk-heterojunction photovoltaic cell. It is shown that the combination of F3Th4 with P3HT allows strong light absorption. The mechanism of charge transfer in the multi-donor PV cell was investigated; it shows that efficient energy transfer takes place from F3Th4 to P3HT. However, the short-circuit current (J_SC) of the multi-donor bulk-heterojunction photovoltaic (PV) cell still decreased. The possible reason for the smaller photocurrent is worsening of transport property after addition of F3Th4.     

Optimization of inverted tandem organic solar cells

Inverted tandem organic solar cells, consisting of two bulk heterojunction sub-cells with identical poly(3-hexylthiophene) (P3HT) and 1-(3-methoxycarbonyl)-propyl-1-phenyl-(6,6)C₆₁ (PCBM) active layer and a MoO₃/Ag/Al/Ca intermediate layer, have been presented and optimized. Indium tin oxide (ITO) modified by Ca acts as a cathode for electron collection and Ag is used as the anode for hole collection for the tandem device. A proper thickness of Ca (3 nm) forms a continuous layer, working as a cathode for the top sub-cell. MoO₃ as the anode buffer layer prevents exciton quenching and charge loss at the anode side, which could result in increase in interfacial resistance. The variance of sub-cell thickness adjusts the optical field distribution in the entire device, facilitating light absorption and good current matching in both sub-cells. The optimal inverted tandem device achieves a maximum power conversion efficiency of 2.89% with a short-circuit current density of 4.19 mA/cm², an open-circuit voltage of 1.17 V, and a fill factor of 59.0% under simulated 100 mW/cm² (AM 1.5G) solar irradiation.     

Nanostructured polymer blends (P3HT/PMMA): Inorganic titania hybrid photovoltaic devices

We have fabricated a photovoltaic (PV) device based on the polymer blends of (poly(3-hexylthiophene) (P3HT)/polymethylmethacrylate (PMMA)) and inorganic TiO₂ nanorod bulk heterojunction. The optimized photovoltaic device with 1.6 wt% PMMA concentration has a power conversion efficiency of 0.65% under simulated AM 1.5 illumination (100 mW/cm²), which is 38% more efficient than the device without the incorporation of PMMA. Furthermore, the PMMA-included device gives a short-circuit current density of 2.57 mA/cm², an open-circuit voltage of 0.53 V, and a fill factor of 0.48. Our studies have shown that having optimal PMMA concentration in the photovoltaic devices helps to smoothen the surface of the hybrid thin film, broaden the absorption spectrum, and improve the electrical conductivity. The results implying improvement in cell performance can be illustrated using atomic force microscopy (AFM), a UV/vis spectrophotometer and electrical measurements.