Epoxy‐tert‐butyl poly(cyanoarylene ether) blends: Phase morphology,fracture toughness,and mechanical properties

Tert‐butyl hydroquinone–based poly(cyanoarylene ether) (PENT) was synthesized by the nucleophilic aromatic substitution reaction of 2,6‐dichlorobenzonitrile with tert‐butyl hydroquinone using N‐methyl‐2‐pyrrolidone (NMP) as solvent in the presence of anhydrous potassium carbonate in a nitrogen atmosphere at 200°C. PENT‐toughened diglycidyl ether of bisphenol A epoxy resin (DGEBA) was developed using 4,4′‐diaminodiphenyl sulfone (DDS) as the curing agent. Scanning electron micrographs revealed that all blends had a two‐phase morphology. The morphology changed from dispersed PENT to a cocontinuous structure with an increase in PENT content in the blends from 5 to 15 phr. The viscoelastic properties of the blends were investigated using dynamic mechanical thermal analysis. The storage modulus of the blends was less than that of the unmodified resin, whereas the loss modulus of the blends was higher than that of the neat epoxy. The tensile strength of the blends improved slightly, whereas flexural strength remained the same as that of the unmodified resin. Fracture toughness was found to increase with an increase in PENT content in the blends. Toughening mechanisms like local plastic deformation of the matrix, crack path deflection, crack pinning, ductile tearing of thermoplastic, and particle bridging were evident from the scanning electron micrographs of failed specimens from the fracture toughness measurements. The thermal stability of the blends were comparable to that of the neat resin. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 3536–3544, 2006     

Toughening of an epoxy resin with hydroxy‐terminated poly(arylene ether nitrile) with pendent tertiary butyl groups

Hydroxy‐terminated poly(arylene ether nitrile) oligomers with pendent tert‐butyl groups (PENTOH) were synthesized by the nucleophilic aromatic substitution reaction of 2,6‐dichlorobenzonitrile with tert‐butyl hydroquinone in N‐methyl‐2‐pyrrolidone medium with anhydrous potassium carbonate as a catalyst at 200°C in a nitrogen atmosphere. The PENTOH oligomers were blended with diglycidyl ether of bisphenol A epoxy resin and cured with 4,4′‐diaminodiphenyl sulfone. The curing reaction was monitored with infrared spectroscopy and differential scanning calorimetry. The morphology, fracture toughness, and thermomechanical properties of the blends were investigated. The scanning electron micrographs revealed a two‐phase morphology with a particulate structure of the PENTOH phase dispersed in the epoxy matrix, except for the epoxy resin modified with PENTOH with a number‐average molecular weight of approximately 4000. The storage modulus of the blends was higher than that of the neat epoxy resin. The crosslink density calculated from the storage modulus in the rubbery plateau region decreased with an increase in PENTOH in the blends. The fracture toughness increased more than twofold with the addition of PENTOH oligomers. The tensile strength of the blends increased marginally, whereas the flexural strength decreased marginally. The dispersed PENTOH initiated several toughening mechanisms, which improved the fracture toughness of the blends. The thermal stability of the epoxy resin was not affected by the addition of PENTOH to the epoxy resin. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Toughening of epoxy/polycaprolactone composites via reaction induced phase separation

A series of melt processable thermoset/thermoplastic blends were prepared by mixing bisphenol‐A diglycidyl ether (Epon‐828)/diaminodiphenyl sulfone (DGEBA/DDS) system with two grades of polycaprolactone resin. Phase separation behavior of the blends was investigated by means of optical microscopy, microstructure by scanning electron microscopy (SEM), and thermo‐mechanical properties. The toughness of polycaprolactone modified epoxies was measured by instrumented falling weight impact (IFWI) testing. Various blend morphologies were observed depending upon the cured epoxy network/thermoplastic composition. Spinodal decomposition as characterized by modulated structure of unique periodicity and phase connectivity was found to be the probable mechanism of phase separation. SEM examination of fracture surfaces indicated a strong adhesion between the epoxy‐rich and polycaprolactone‐rich phases. Optimum improvement in failure energy was obtained for the compositions containing 10‐20% polycaprolactone without significantly compromising the elastic modulus and the thermo‐mechanical stability of the epoxy. In light of morphological evidences, a possible toughening effect was postulated in terms of tearing of the thermoplastic component and induced plastic deformation of the epoxy matrix.     

Epoxy modification with poly(vinyl acetate) and poly(vinyl butyral). I. Structure,thermal, and mechanical characteristics

Efficiency of the application of high strength heat resistant thermoplastics for improving fracture toughness and impact properties of epoxy resins motivated authors to try large‐scale production thermoplastics for the same purpose. Epoxy/anhydride systems were modified by up to 8 wt % poly(vinyl acetate) (PVAc) and up to 6 wt % poly(vinyl butyral) (PVB). In epoxy–PVAc blends it was possible to obtain morphologies with continuous thermoplastic phase. However, only sea‐island morphologies with a very small size of PVB‐rich phase were observed in epoxy–PVB matrices. The former type of morphology allowed a notable 2.4‐fold increase in the fracture toughness of epoxy resin and simultaneous up to 30% decrease in its' impact strength. The latter type of morphology caused a notably lower (45%) enhancement of the epoxy fracture toughness combined with a 50% increase in its' impact strength. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44081.     

Hydroxyl terminated poly(ether ether ketone) with pendent methyl group toughened epoxy resin: miscibility, morphology and mechanical properties

The synthesis, processing, thermal and mechanical properties and fracture toughness of epoxy resin formulated with hydroxyl terminated poly(ether ether ketone) with pendent methyl group are reported. Hydroxyl terminated poly(ether ether ketone) oligomers based on methyl hydroquinone (PEEKMOH) were synthesised from methylhydroquinone and 4,4′-difluorobenzophenone in N-methyl-2-pyrrolidone. PEEKMOH oligomers with different molecular weights were synthesised and characterised. Blends of diglycidyl ether of bisphenol-A epoxy resin with PEEKMOH were prepared by melt mixing. The uncured blends were homogeneous and the T_g-composition behaviour was predicted using Fox, Gordon–Taylor and Kelley–Bueche equations. Reaction induced phase separation occurred in the blends on curing with 4,4′-diaminodiphenyl sulfone. Scanning electron microscopy studies revealed the two-phase morphology of the blends. Domain size of the blends increased with increase in PEEKMOH8 in the blends. Phase separation in the blends occurred by nucleation and growth mechanism. Infrared spectroscopic studies revealed that some of the epoxy groups were opened up by hydroxyl group of PEEKMOH. The tensile and flexural properties of the blends were comparable to that of neat epoxy resin and the properties were dependent on the composition of the blend and molecular weight of PEEKMOH used. Dynamic mechanical analysis revealed two glass transition temperatures corresponding to epoxy rich and thermoplastic rich phases. The crosslink density of epoxy resin decreased with the addition of PEEKMOH to epoxy resin. The blends exhibited superior fracture toughness compared to unmodified epoxy resin. The increase in fracture toughness was due to local plastic deformation of the matrix, crack path deflection and crack pinning. The thermal stability of amine cured epoxy resin was not affected by the incorporation of PEEKMOH into the epoxy resin.     

Surface morphology,thermomechanical and barrier properties of poly(ether sulfone)‐toughened epoxy clay ternary nanocomposites

Poly(ether sulfone) (PES)‐toughened epoxy clay ternary nanocomposites were prepared by melt blending of PES with diglycidyl ether of bisphenol A epoxy resin along with Cloisite 30B followed by curing with 4,4′‐diaminodiphenylsulfone. The effect of organoclay and thermoplastic on the fracture toughness, permeability, viscoelasticity and thermomechanical properties of the epoxy system was investigated. A significant improvement in fracture toughness and modulus with reduced coefficient of thermal expansion (CTE) and gas permeability were observed with the addition of thermoplastic and clay to the epoxy system. Scanning electron microscopy of fracture‐failed specimens revealed crack path deflection and ductile fracture without phase separation. Oxygen gas permeability was reduced by 57% and fracture toughness was increased by 66% with the incorporation of 5 phr clay and 5 phr thermoplastic into the epoxy system. Optical transparency was retained even with high clay content. The addition of thermoplastic and organoclay to the epoxy system had a synergic effect on fracture toughness, modulus, CTE and barrier properties. Planetary ball‐milled samples gave exfoliated morphology with better thermomechanical properties compared to ultrasonicated samples with intercalated morphology. Copyright © 2010 Society of Chemical Industry     

Enhanced fracture toughness of epoxy resins with novel amine‐terminated poly(arylene ether sulfone)–carboxylic‐terminated butadiene‐acrylonitrile–poly(arylene ether sulfone) triblock copolymers

Amine‐terminated poly(arylene ether sulfone)–carboxylic‐terminated butadiene‐acrylonitrile–poly(arylene ether sulfone) (PES‐CTBN‐PES) triblock copolymers with controlled molecular weights of 15,000 (15K) or 20,000 (20K) g/mol were synthesized from amine‐terminated PES oligomer and commercial CTBN rubber (CTBN 1300x13). The copolymers were utilized to modify a diglycidyl ether of bisphenol A epoxy resin by varying the loading from 5 to 40 wt %. The epoxy resins were cured with 4,4′‐diaminodiphenylsulfone and subjected to tests for thermal properties, plane strain fracture toughness (K_IC), flexural properties, and solvent resistance measurements. The fracture surfaces were analyzed with SEM to elucidate the toughening mechanism. The properties of copolymer‐toughened epoxy resins were compared to those of samples modified by PES/CTBN blends, PES oligomer, or CTBN. The PES‐CTBN‐PES copolymer (20K) showed a K_IC of 2.33 MPa m^0.5 at 40 wt % loading while maintaining good flexural properties and chemical resistance. However, the epoxy resin modified with a CTBN/8K PES blend (2:1) exhibited lower K_IC (1.82 MPa m^0.5), lower flexural properties, and poorer thermal properties and solvent resistance compared to the 20K PES‐CTBN‐PES copolymer‐toughened samples. The high fracture toughness with the PES‐CTBN‐PES copolymer is believed to be due to the ductile fracture of the continuous PES‐rich phases, as well as the cavitation of the rubber‐rich phases. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1556–1565, 2002; DOI 10.1002/app.10390     

Epoxidized natural rubber/epoxy blends: Phase morphology and thermomechanical properties

Epoxidized natural rubbers (ENRs) were prepared. ENRs with different concentrations of up to 20 wt % were used as modifiers for epoxy resin. The epoxy monomer was cured with nadic methyl anhydride as a hardener in the presence of N,N‐dimethyl benzyl amine as an accelerator. The addition of ENR to an anhydride hardener/epoxy monomer mixture gave rise to the formation of a phase‐separated structure consisting of rubber domains dispersed in the epoxy‐rich phase. The particle size increased with increasing ENR content. The phase separation was investigated by scanning electron microscopy and dynamic mechanical analysis. The viscoelastic behavior of the liquid‐rubber‐modified epoxy resin was also evaluated with dynamic mechanical analysis. The storage moduli, loss moduli, and tan δ values were determined for the blends of the epoxy resin with ENR. The effect of the addition of rubber on the glass‐transition temperature of the epoxy matrix was followed. The thermal stability of the ENR‐modified epoxy resin was studied with thermogravimetric analysis. Parameters such as the onset of degradation, maximum degradation temperature, and final degradation were not affected by the addition of ENR. The mechanical properties of the liquid‐natural‐rubber‐modified epoxy resin were measured in terms of the fracture toughness and impact strength. The maximum impact strength and fracture toughness were observed with 10 wt % ENR modified epoxy blends. Various toughening mechanisms responsible for the enhancement in toughness of the diglycidyl ether of the bisphenol A/ENR blends were investigated. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39906.     

Preparation and properties of TiO2‐filled poly(acrylonitrile‐butadiene‐styrene)/epoxy hybrid composites

Poly (acrylonitrile‐butadiene‐styrene) (ABS) was used to modify diglycidyl ether of bisphenol‐A type of epoxy resin, and the modified epoxy resin was used as the matrix for making TiO₂ reinforced nanocomposites and were cured with diaminodiphenyl sulfone for superior mechanical and thermal properties. The hybrid nanocomposites were characterized by using thermogravimetric analyzer (TGA), dynamic mechanical analyzer (DMA), universal testing machine (UTM), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The bulk morphology was carefully analyzed by SEM and TEM and was supported by other techniques. DMA studies revealed that the DDS‐cured epoxy/ABS/TiO₂ hybrid composites systems have two T_gs corresponding to epoxy and ABS rich phases and have better load bearing capacity with the addition of TiO₂ particles. The addition of TiO₂ induces a significant increase in tensile properties, impact strength, and fracture toughness with respect to neat blend matrix. Tensile toughness reveals a twofold increase with the addition of 0.7 wt % TiO₂ filler in the blend matrix with respect to neat blend. SEM micrographs of fractured surfaces establish a synergetic effect of both ABS and TiO₂ components in the epoxy matrix. The phenomenon such us cavitation, crack path deflection, crack pinning, ductile tearing of the thermoplastic, and local plastic deformation of the matrix with some minor agglomerates of TiO₂ are observed. However, between these agglomerates, the particles are separated well and are distributed homogeneously within the polymer matrix. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Morphology and properties of an epoxy alloy system containing thermoplastics and a reactive rubber

A novel approach for toughening thermosetting epoxy matrices using both thermoplastics and liquid reactive rubbers as modifiers has been investigated. The network structure of the modified epoxy systems was characterized using dynamic mechanical analysis, and the morphology of the multiphase structure was examined using scanning electron microscopy (SEM). To investigate the continuity of the phase domains, the constituents in the phase domains were positively identified using solving etching and RuO₄ staining techniques for transmission electron microscopy (TEM). The fracture toughness of the modified and basic epoxy samples was measured using compact tension (CT) specimens. Quite limited toughness improvement was achieved for the epoxy modified with only the PSu thermoplastic, or the liquid rubber by itself. However, the fracture toughness was found to increase dramatically when a proper combination of both the liquid reactive rubber and thermoplastic was simultaneously incorporated into the epoxy. Toughening by using dual modifiers resulted in maximum improvement of fracture toughness with minimal compromises in processability and T_g depression by rubbers.     

Miscibility and mechanical properties of tetrafunctional epoxy resin/phenolphthalein poly(ether ether ketone) blends

Phenolphthalein poly(ether ether ketone) (PEK‐C) was found to be miscible with uncured tetraglycidyl 4,4′‐diaminodiphenylmethane (TGDDM), which is a type of tetrafunctional epoxy resin (ER), as shown by the existence of a single glass transition temperature (T_g) within the whole composition range. The miscibility between PEK‐C and TGDDM is considered to be due mainly to entropy contribution. Furthermore, blends of PEK‐C and TGDDM cured with 4,4′‐diaminodiphenylmethane (DDM) were studied using dynamic mechanical analysis (DMA), Fourier‐transform infrared (FTIR) spectroscopy, and scanning electron microscopy (SEM). DMA studies show that the DDM‐cured TGDDM/PEK‐C blends have only one T_g. SEM observation also confirmed that the blends were homogeneous. FTIR studies showed that the curing reaction is incomplete due to the high viscosity of PEK‐C. As the PEK‐C content increased, the tensile properties of the blends decreased slightly and the fracture toughness factor also showed a slight decreasing tendency, presumably due to the reduced crosslink density of the epoxy network. SEM observation of the fracture surfaces of fracture toughness test specimens showed the brittle nature of the fracture for the pure ER and its blends with PEK‐C. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 79: 598–607, 2001     

Cure kinetics and morphology of blends of epoxy resin with poly (ether ether ketone) containing pendant tertiary butyl groups

The cure kinetics and morphology of diglycidyl ether of bisphenol-A (DGEBA) epoxy resin modified with a poly (ether ether ketone) based on tertiary butyl hydroquinone (PEEK-T) cured with diamino diphenyl sulphone (DDS) were investigated using differential scanning calorimetry (DSC), scanning electron microscopy (SEM) and dynamic mechanical thermal analysis (DMTA). The results obtained from DSC were applied to autocatalytic and diffusion controlled kinetic models. The reaction mechanism broadly showed autocatalytic behaviour regardless of the presence of PEEK-T. At higher PEEK-T concentration, more diffusion controlled mechanism was observed. The rate of curing reaction decreased with increase in thermoplastic content and also with the lowering of curing temperature. The activation energies of the blends are higher than that of the neat resin. The blends showed a phase separated morphology. The dispersed phase showed a homogeneous particle size distribution. The T_g of the neat resin decreased with the decrease in cure temperature. Two T_g's corresponding to the epoxy rich and thermoplastic rich phases were observed in the dynamic mechanical spectrum. The storage modulus of 10 and 20 phr PEEK-T blends are found to be greater than the neat resin.     

High performance HTLNR/epoxy blend—Phase morphology and thermo-mechanical properties

An attempt was made to toughen diglycidyl ether of bisphenol A (DGEBA) type epoxy resin with liquid natural rubber possessing hydroxyl functionality (HTLNR). Epon 250 epoxy monomer is cured using nadic methyl anhydride as hardener in presence of N, N dimethyl benzyl amine as accelerator. HTLNR of different concentrations up to 20 wt % is used as modifier for epoxy resin. The addition HTLNR to an anhydride hardener/epoxy monomer mixture has given rise to the formation of phase-separated structure, consisting of small spherical liquid natural rubber particles bonded to the surrounding epoxy matrix. The particle size increased with increase in rubber content. The viscoelastic properties of the blends were analyzed using dynamic mechanical thermal analysis. The T_g corresponding to epoxy rich phase was evident from the dynamic mechanical spectrum, while the T_g of the rubber phase was overlapped by the β relaxation of epoxy phase. Glass transition of the epoxy phase decreased linearly as a function of the amount of rubber. The mechanical properties such as impact and fracture toughness were also carefully examined. The impact and fracture toughness increase with HTLNR content. A threefold increase in impact strength was observed with 15 wt % HTLNR/epoxy blend. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Mechanical,thermal, and viscoelastic response of novel in situ CTBN/POSS/epoxy hybrid composite system

The present study focuses on the preparation of a novel hybrid epoxy nanocomposite with glycidyl polyhedral oligomeric silsesquioxane (POSS) as nanofiller, carboxyl terminated poly(acrylonitrile‐co‐butadiene) (CTBN) as modifying agent and diglycidyl ether of bisphenol A (DGEBA) as matrix polymer. The reaction between DGEBA, CTBN, and glycidyl POSS was carefully monitored and interpreted by using Fourier transform infrared (FTIR) and differential scanning calorimetry (DSC). An exclusive mechanism of the reaction between the modifier, nanofiller, and the matrix is proposed herein, which attempts to explains the chemistry behind the formation of an intricate network between POSS, CTBN, and DGEBA. The mechanical properties, such as tensile strength, and fracture toughness, were also carefully examined. The fracture toughness increases for epoxy/CTBN, epoxy/POSS, and epoxy/CTBN/POSS hybrid systems with respect to neat epoxy, but for hybrid composites toughening capability of soft rubber particles is lost by the presence of POSS. Field emission scanning electron micrographs (FESEM) of fractured surfaces were examined to understand the toughening mechanism. The viscoelastic properties of epoxy/CTBN, epoxy/POSS, and epoxy/CTBN/POSS hybrid systems were analyzed using dynamic mechanical thermal analysis (DMTA). The storage modulus shows a complex behavior for the epoxy/POSS composites due to the existence of lower and higher crosslink density sites. However, the storage modulus of the epoxy phase decreases with the addition of soft CTBN phase. The T_g corresponding to epoxy‐rich phase was evident from the dynamic mechanical spectrum. For hybrid systems, the T_g is intermediate between the epoxy/rubber and epoxy/POSS systems. Finally, TGA (thermo gravimetric analysis) studies were employed to evaluate the thermal stability of prepared blends and composites. POLYM. COMPOS., 37:2109–2120, 2016. © 2015 Society of Plastics Engineers     

Study on phenolphthalein poly(ether sulfone)‐modified cyanate ester resin and epoxy resin blends

In this work, the phenolphthalein poly(ether sulfone) (PES‐C)‐modified cyanate ester (CE) and epoxy (EP) blends were prepared. This work mainly discusses the curing behaviors, fracture toughness, dynamic mechanical properties, and thermal and mechanical properties of the blends. The Fourier transform infrared and differential scanning calorimetric analyses are used to confirm the curing behaviors, demonstrating that the main reaction pathways are not varied with the addition of PES‐C, but the reaction rate could be evidently accelerated. The fracture morphologies of the blends are observed by Scanning electron microscope (SEM) and the fracture causes of the failed surface are also analyzed. With the addition of PES‐C, the modified blends display higher fracture toughness (K_Ic) and impact strength when compared with neat CE. Domain sizes of the blends first increase then decrease with the addition of PES‐C. The results of dynamic mechanical analysis and thermogravimetric analysis show that the T_g, storage modulus, and thermal stability of the crosslink network slightly decreases with the addition of PES‐C. The mechanical strength of blends with the addition of PES‐C is far better than that of the blends without PES‐C both at ambient temperature and elevated temperature. POLYM. ENG. SCI., 55:2591–2602, 2015. © 2015 Society of Plastics Engineers     

Improving the toughness of epoxy with a reactive tetrablock copolymer containing maleic anhydride

Reactive block copolymers (BCPs) provide a unique means for toughening epoxy thermosets because covalent linkages provide opportunities for greater improvement in the fracture toughness (K_IC). In this study, a tailored reactive tetrablock copolymer, poly[styrene‐alt‐(maleic anhydride)]‐block‐polystyrene‐block‐poly(n‐butyl acrylate)‐block‐polystyrene, was incorporated into a diglycidyl ether of bisphenol A based epoxy resin. The results demonstrate the advantage of reactive BCP in finely tuning and controlling the structure of epoxy blends, even with 95 wt % epoxy‐immiscible triblocks. The size of the dispersed phase was efficiently reduced to submicrometer level. The mechanical properties, such as K_IC, of these cured blends were investigated. The addition of 10 wt % reactive BCP into the epoxy resins led to considerable improvements in the toughness, imparting nearly a 70% increase in K_IC. The designed reactive tetrablock copolymer opened good prospects because of its potential novel applications in toughening modification of engineering polymer composites. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 132, 42826.     

Modified continuous carbon fiber‐reinforced poly(phthalazinone ether sulfone ketone) composites by blending polyetherimide and polyethersulfone

Poly(phthalazinone ether sulfone ketone) (PPESK) is a novel high performance thermoplastic with outstanding high temperature resistance and excellent mechanical properties and therefore, it is a very ideal candidate matrix for advanced composites. However, its high melting viscosity makes the melting process difficult. In this article, two well‐known high performance thermoplastics, polyetherimide (PEI) and polyethersulfone (PES) were introduced to PPESK in order to reduce the melting viscosity of PPESK and to improve the properties of composites. The effect of addition of PEI and PES on the resultant composites was studied. A series of unidirectional composites were made of PPESK and its PEI and PES blends as matrix and continuous carbon fiber (T700) as reinforcement. The solution prepregging method and hot‐press molding method were used in preparation of composites. The effects of polymer blends matrix on mechanical properties, interfacial adhesion, and fracture mode were studied by three points bending, interlaminar shearing, porosity, and scanning electron microscope test. The results show that the mechanical properties and interfacial adhesion increases, and the porosity decrease after blending PEI or PES in the matrix. Addition of PEI and PES to PPESK results in an obvious transition of fracture mode. POLYM. COMPOS., 2009. © 2008 Society of Plastics Engineers     

Control of morphologies and mechanical properties of thermoplastic‐modified epoxy matrices by addition of a second thermoplastic

Ternary mixtures based on stoichiometric mixtures of the diglycidyl ether of bisphenol‐A (DGEBA) and 4,4′‐diaminodiphenyl sulfone (DDS) and two miscible thermoplastics, poly(methyl methacrylate) (PMMA) and the poly(hydroxy ether of bisphenol‐A) (phenoxy), were investigated by optical microscopy (OM), atomic force microscopy (AFM) and dynamic mechanical analysis (DMA). Mechanical testing was used to study the ultimate behavior. All the modified epoxy mixtures were heterogeneous. DMA has been shown to be an excellent technique for detecting the morphologies generated after curing when the loss modulus is used for analysis. Morphology varied with the thermoplastic content on the mixtures. The addition of a second thermoplastic in small amounts changed the morphological features from particulated to co‐continuous and from that to phase‐inverted morphologies. A significant increase in fracture toughness was observed above all for the mixtures with some level of co‐continuity within the epoxy‐rich matrix. Phase inversion led to poor strength and also fracture toughness. Copyright © 2003 Society of Chemical Industry     

Blends of epoxy resin with amine‐terminated polyoxypropylene elastomer: Morphology and properties

A liquid diglycidyl ether of bisphenol A (DGEBA) epoxy resin is blended in various proportions with amine‐terminated polyoxypropylene (POPTA) and cured using an aliphatic diamine hardener. The degree of crosslinking is varied by altering the ratio of diamine to epoxy molecules in the blend. The mixture undergoes almost complete phase separation during cure, forming spherical elastomer particles at POPTA concentrations up to 20 wt %, and a more co‐continuous morphology at 25 wt %. In particulate blends, the highest toughness is achieved with nonstoichiometric amine‐to‐epoxy ratios, which produce low degrees of crosslinking in the resin phase. In these blends, the correlation between G_IC and plateau modulus (above the resin T_g), over a wide range of amine‐to‐epoxy ratios, confirms the importance of resin ductility in determining the fracture resistance of rubber‐modified thermosets. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 72: 427–434, 1999     

Morphology,viscoelastic properties,and mechanical behavior of epoxy resin modified with hydroxyl‐terminated poly(ether ether ketone) oligomer with pendent tert‐butyl groups

Hydroxyl‐terminated poly (ether ether ketone) with pendent tert‐butyl groups (PEEKTOH) synthesized from 4,4′‐difluorobenzophenone and tert‐butyl hydroquinone was blended with diglycidyl ether of bisphenol‐A (DGEBA) epoxy resin. A diamine, 4,4′‐diaminodiphenyl sulfone (DDS) was used as the curing agent. The thermal and mechanical properties, fracture toughness, and morphology of the blends were investigated. Morphological analysis of the blends revealed a particulate structure with PEEKTOH phase dispersed in the epoxy matrix. Unlike classical polymer blend systems, increase in concentration of PEEKTOH does not increase the domain size. Instead, a decrease is obtained. The fracture toughness increased with the addition of oligomer without much decrease in tensile and flexural strengths. Addition of 15 phr oligomer gave maximum toughness. The dispersed PEEKTOH initiated several mechanisms that improved the fracture toughness of the blends. The cross‐link density calculated from the storage modulus in the rubbery plateau region decreased with the increase in PEEKTOH. The thermal stability of epoxy resin remained unaffected even after blending with PEEKTOH. POLYM. ENG. SCI., 45:1645–1654, 2005. © 2005 Society of Plastics Engineers