Characteristics of transparent ZnO based thin film transistors with amorphous HfO2 gate insulators and Ga doped ZnO electrodes

Coplanar type transparent thin film transistors (TFTs) have been fabricated on the glass substrates. The devices consist of intrinsic ZnO, Ga doped ZnO (GZO), and amorphous HfO₂ for the semiconductor active channel layer, electrode, and gate insulator, respectively. GZO and HfO₂ layers were prepared by using a pulsed laser deposition (PLD) and intrinsic ZnO layers were fabricated by using an rf-magnetron sputtering. The transparent TFT exhibits n-channel, enhancement mode behavior. The field effect mobility, threshold voltage, and a drain current on-to-off ratio were measured to be 14.7 cm²/Vs, 2 V, and 10⁵, respectively. High optical transmittance (> 85%) in visible region makes ZnO TFTs attractive for transparent electronics.     

The influence of fabrication process on top-gate thin-film transistors

Amorphous indium zinc oxide (a-IZO) thin-film transistors (TFTs) with bottom- and top-gate structures were fabricated at room temperature by direct current (DC) magnetron sputter in this research. High dielectric constant (κ) hafnium oxide (HfO₂) films and a-IZO were deposited for the gate insulator and the semiconducting channel under a mixture of ambient argon and oxygen gas, respectively. The bottom-gate TFTs showed good TFT characteristics, but the top-gate TFTs did not display the same characteristics as the bottom-gate TFTs despite undergoing the same process of sputtering with identical conditions. The electrical characteristics of the top-gate a-IZO TFTs exhibited strong relationships with sputtering power as gate dielectric layer deposition in this study. The ion bombardment and incorporation of sputtering ions damaged the interface between the active layer and the gate insulator in top-gate TFTs. Hence, the sputtering power was reduced to decrease damage while depositing HfO₂ films. When using 50 W DC magnetron sputtering, the top-gate a-IZO TFTs showed the following results: a saturation mobility of 5.62 cm²/V-s; an on/off current ratio of 1 × 10⁵; a sub-threshold swing (SS) of 0.64 V/decade; and a threshold voltage (V_th) of 2.86 V.     

High mobility bottom gate nanocrystalline-Si thin-film transistors

We developed high mobility bottom gate nanocrystalline (nc)-Si thin-film transistors (TFTs). nc-Si film was deposited using inductively coupled plasma chemical vapor deposition method on SiN_x gate insulator. Because of good film crystallinity and low ion damage, we could get high performance TFT characteristics. Our TFT showed field effect mobility of 9.4 cm² V^− 1 s^− 1 for electrons. These results showed that bottom gate nc-Si TFT could be used in applications such as next generation high definition television and organic light-emitting diode display.     

Effect of thickness of ZnO active layer on ZnO-TFT's characteristics

We have investigated the electrical characteristics of ZnO thin film transistors with respect to the thickness of ZnO active layers. The ZnO layers with the thickness of 30 nm to 150 nm were deposited on bottom gate patterned Si substrate by RF sputtering at room temperature. The low-temperature oxide served as gate dielectric. As ZnO channel layer got thicker, the leakage current at V_DS = 30 V and V_G = 0 V greatly increased from 10^− 10 A to 10^− 6 A, while the threshold voltage decreased from 15 V to 10 V. On the other hand, the field effect mobility got around 0.15 cm²/V s except for the 30-nm-thick channel. Overall, the 55-nm-thick ZnO channel layer showed the best performance.     

Wet etching rates of InGaZnO for the fabrication of transparent thin-film transistors on plastic substrates

The wet etch process for amorphous indium gallium zinc oxide (a-IGZO or a-InGaZnO) by using various etchants is reported. The etch rates of a-IGZO, compared to another indium-based oxides including indium gallium oxide (IGO), indium zinc oxide (IZO), and indium tin oxide (ITO), are measured by using acetic acid, citric acid, hydrochloric acid, perchloric acid, and aqua ammonia as etchants, respectively. In our experimental results, the etch rate of the transparent oxide semiconductor (TOS) films by using acid solutions ranked accordingly from high to low are IZO, IGZO, IGO and ITO. Comparatively, the etch rate of the TOS films by using alkaline ammonia solution ranked from high to low are IGZO, IZO, IGO and ITO, in that order.Using the proposed wet etching process with high etch selectivity, bottom-gate-type thin-film transistors (TFTs) based on a-IGZO channels and Y₂O₃ gate-insulators were fabricated by radio-frequency sputtering on plastic substrates. The wet etch processed TFT with 30 µm gate length and 120 µm gate width exhibits a saturation mobility of 46.25 cm² V^− 1 s^− 1, a threshold voltage of 1.3 V, a drain current on-off ratio > 10⁶ , and subthreshold gate voltage swing of 0.29 V decade^− 1. The performance of the TFTs ensures the applicability of the wet etching process for IGZO to electronic devices on organic polymer substrates.     

Comparison of a-Si TFTs fabricated by Cat-CVD and PECVD methods

We investigate the characteristics of amorphous silicon thin film transistors (a-Si TFTs) fabricated by plasma-enhanced chemical vapor deposition (PECVD) and catalytic CVD (Cat-CVD), and their stability under bias and temperature (BT) accelerated stress. The Cat-CVD a-Si TFTs have off-leak current as small as 10^− 14 A, and a smaller threshold voltage shift under the BT stress. The superiority in off-leak current and stability is observed in the Cat-CVD a-Si TFTs fabricated at both 320 °C and 180 °C. The high performance and stability of the Cat-CVD a-Si TFTs will enable to use low-cost glass substrates and result in a cost reduction of TFT fabrication.     

Effect of hafnium addition on the electrical properties of indium zinc oxide thin film transistors

This study reports the performance and stability of hafnium-indium zinc oxide (HfInZnO) thin film transistors (TFTs) with thermally grown SiO2. The HfInZnO channel layer was deposited at room temperature by a co-sputtering system. We examined the effects of hafnium addition on the X-ray photoelectron spectroscopy properties and on the electrical characteristics of the TFTs varying the concentration of the added hafnium. We found that the transistor on-off currents were greatly influenced by the composition of hafnium addition, which suppressed the formation of oxygen vacancies. The field-effect mobility of optimized HfInZnO TFT was 1.34 cm² V⁻¹ s⁻¹, along with an on-off current ratio of 10⁸ and a threshold voltage of 4.54 V. We also investigated the effects of bias stress on HfInZnO TFTs with passivated and non-passivated layers. The threshold voltage change in the passivated device after positive gate bias stress was lower than that in the non-passivated device. This result indicates that HfInZnO TFTs are sensitive to the ambient conditions of the back surface.     

Fullerene thin-film transistors fabricated on polymeric gate dielectric

Thin-film transistors with fullerene as n-type organic semiconductor have been fabricated. A polymeric gate dielectric, polymethyl methacrylate, has been used as an alternative to usual inorganic dielectrics. No significant differences in the microstructure of fullerene thin-films grown on polymethyl methacrylate were observed. Devices with either gold or aluminium top electrodes have been fabricated. Although the lower work-function of aluminium compared to gold should favour electron injection, similar field-effect mobilities in the range of 10^− 2 cm² V^− 1 s^− 1 were achieved in both cases. Actually, the output characteristics indicate that organic thin-film transistors behave more linearly with gold than with aluminium electrodes. These results confirm that not only energy barriers determine carrier injection at metal/organic interfaces, but also chemical interactions.     

Amorphous structure and electrical performance of low-temperature annealed amorphous indium zinc oxide transparent thin film transistors

The effect of low-temperature (200 °C) annealing on the threshold voltage, carrier density, and interface defect density of amorphous indium zinc oxide (a-IZO) thin film transistors (TFTs) is reported. Transmission electron microscopy and x-ray diffraction analysis show that the amorphous structure is retained after 1 h at 200 °C. The TFTs fabricated from as-deposited IZO operate in the depletion mode with on-off ratio of > 10⁶, sub-threshold slope (S) of ~ 1.5 V/decade, field effect mobility (μ_FE) of 18 ± 1.6 cm²/Vs, and threshold voltage (V_Th) of − 3 ± 0.7 V. Low-temperature annealing at 200 °C in air improves the on-current, decreases the sub-threshold slope (1.56 vs. 1.18 V/decade), and increases the field effect mobility (μ_FE) from 18.2 to 23.3 cm²/Vs but also results in a V_Th shift of − 15 ± 1.1 V. The carrier density in the channel of the as-deposited (4.3 × 10¹⁶ /cm³) and annealed at 200 °C (8.1 × 10¹⁷ /cm³) devices were estimated from test-TFT structures using the transmission line measurement methods to find channel resistivity at zero gate voltage and the TFT structures to estimate carrier mobility.     

Enhancement-mode thin film transistor with nitrogen-doped ZnO channel layer deposited by laser molecular beam epitaxy

The thin film transistors (TFTs) based on nitrogen doped zinc oxide (ZnO) were investigated by laser molecular beam epitaxy. The increase of ZnO films' resistivity by nitrogen doping was found and applied in enhancement mode ZnO-TFTs. The ZnO-TFTs with a conventional bottom-gate structure were fabricated on thermally oxidized p-type silicon substrate. Electrical measurement has revealed that the devices operate as an n-channel enhancement mode and exhibit an on/off ratio of 10⁴. The threshold voltage is 5.15 V. The channel mobility on the order of 2.66 cm² V^− 1 s^− 1 has been determined.     

High-performance amorphous indium-gallium-zinc oxide thin-film transistors with polymer gate dielectric

The fabrication of amorphous indium-gallium-zinc oxide (a-IGZO) thin-film transistors (TFTs) with a spin-coated polymer gate dielectric on a glass substrate is reported. The interface state density at the poly(4-vinylphenol)/a-IGZO interface is only around 4.05 × 10¹¹ cm^− 2. The TFTs' threshold voltage, subthreshold swing, on-off current ratio, and carrier mobility are 2.6 V, 1.3 V/decade, 1 × 10⁵, and 21.8 cm²/V s, respectively. These characteristics indicate that the TFTs are suitable for use as nonvolatile memory devices and in flexible electronic applications.     

Physical/chemical properties of tin oxide thin film transistors prepared using plasma-enhanced atomic layer deposition

Thin film transistors (TFTs) with tin oxide films as the channel layer were fabricated by means of plasma enhanced atomic layer deposition (PE-ALD). The as-deposited tin oxide films show n-type conductivity and a nano-crystalline structure of SnO₂. Notwithstanding the relatively low deposition temperatures of 70, 100, and 130 °C, the bottom gate tin oxide TFTs show an on/off drain current ratio of 10⁶ while the device mobility values were increased from 2.31 cm²/V s to 6.24 cm²/V s upon increasing the deposition temperature of the tin oxide films.     

Investigation on indium concentration dependence of solution processed indium tin oxide thin film transistors

The effect of the indium content in indium tin oxide (ITO) films fabricated using a solution-based process and ITO channel thin film transistors (TFTs) was examined as a function of the indium mole ratio. The carrier concentration and resistivity of the ITO films could be controlled by the appropriate treatments. The TFTs showed an increase in the off-current due to the enhanced conductivity of the ITO channel layer with increasing indium mole ratios, producing an increase in the field effect mobility. The characteristics of the a-ITO channel TFT showed the best performance (μ_FE of 3.0 cm² V^− 1 s^− 1, V_th of 2.0 V, and S value of 0.4 V/decade) at In:Sn = 5:1.     

Fabrication and comparative study of top-gate and bottom-gate ZnO–TFTs with various insulator layers

Transparent ZnO thin film transistors (ZnO–TFTs) with different structures and dielectric layers were fabricated by rf magnetron sputtering. The PbTiO₃, AlO _x , SiN _x and SiO _x films were attempted to serve as the gate dielectric layers in the devices, respectively, and XRD was employed to investigate the crystal structure of ZnO films deposited on these dielectric layers. The optical properties of transparent TFTs were measured and revealed the average transmittance ranged from 60 to 80% in the visible part of the spectrum. Electrical measurement shows the properties of the ZnO–TFTs have great relations with the device structure. The bottom-gate TFTs have better behaviors than top-gate ones with the mobility, threshold voltage and the current on/off ratio of 18.4 cm² V⁻¹ s⁻¹, −0.7 V and 10⁴, respectively. The electrical difference of the devices may be due to different character of the interface between the channel and dielectric layers.     

An investigation of contact resistance between metal electrodes and amorphous gallium-indium-zinc oxide (a-GIZO) thin-film transistors

This paper reports our investigation of different source/drain (S/D) electrode materials in thin-film transistors (TFTs) based on an indium-gallium-zinc oxide (IGZO) semiconductor. Transfer length, contact resistance, channel conductance, and effective resistances between S/D electrodes and amorphous IGZO thin-film transistors were examined. Intrinsic TFT parameters were extracted by the transmission line method (TLM) using a series of TFTs with different channel lengths measured at a low drain voltage. The TFTs fabricated with Cu S/D electrodes showed the lowest contact resistance and transfer length indicating good ohmic characteristics, and good transfer characteristics with intrinsic field-effect mobility (μ_FE-i) of 10.0 cm²/Vs.     

Effect of oxygen partial pressure on electrical characteristics of amorphous indium gallium zinc oxide thin-film transistors fabricated by thermal annealing

We report the fabrication and electrical characteristics of high-performance amorphous indium gallium zinc oxide (a-IGZO) thin-film transistors (TFTs) with a polymer gate dielectric prepared by spin coating on a glass substrate at different oxygen partial pressure values. The transmittance of the deposited polymer film was greater than 90% at 600 nm a-IGZO thin films were deposited on glass substrates using RF magnetron sputtering at different oxygen partial pressure values. The a-IGZO TFTs were prepared by rapid thermal annealing at 350 °C for 10 min at a 0.2% oxygen partial pressure. It was observed that a-IGZO TFTs with an active channel layer exhibited enhanced mode operation, a threshold voltage of 1 V, an on-off current ratio of 10³, and a field-effect mobility of 18 cm²/Vs.     

Analysis of carrier modulation in channel of ferroelectric-gate transistors having polar semiconductor

We have been fabricated and characterized a ferroelectric-gate thin-film transistors (TFTs) using ZnO as a channel polar semiconductor and YMnO₃ as a ferroelectric gate. A typical n-channel transistor property showing clear drain current saturation in I_D-V_D (drain current - drain voltage) characteristics was recognized. When the 3 V of the gate voltage is applied under the 4 V of drain voltage, the large drain current of about 1.1 mA is obtained. These controlled-polarization-type ferroelectric-gate TFTs using ZnO-channel TFTs operate in the accumulation-depletion mode and the ON/OFF state of the ferroelectric-gate TFTs strongly depends on the polarization switching of P_SFe. In this paper, therefore, the polarization switching of P_SFe in the TFT is carefully examined and the relationship between the polarization switching and the carrier accumulation (depletion) state is discussed using impedance spectroscopy and Capacitance-Voltage (C-V) measurements at applied the gate voltage.     

Effect of oxygen partial pressure on electrical characteristics of amorphous indium gallium zinc oxide thin-film transistors fabricated by thermal annealing

We report the fabrication and electrical characteristics of high-performance amorphous indium gallium zinc oxide (a-IGZO) thin-film transistors (TFTs) with a polymer gate dielectric prepared by spin coating on a glass substrate at different oxygen partial pressure values. The transmittance of the deposited polymer film was greater than 90% at 600 nm a-IGZO thin films were deposited on glass substrates using RF magnetron sputtering at different oxygen partial pressure values. The a-IGZO TFTs were prepared by rapid thermal annealing at 350 °C for 10 min at a 0.2% oxygen partial pressure. It was observed that a-IGZO TFTs with an active channel layer exhibited enhanced mode operation, a threshold voltage of 1 V, an on-off current ratio of 10³, and a field-effect mobility of 18 cm²/Vs.     

High performance self-aligned top-gate ZnO thin film transistors using sputtered Al2O3 gate dielectric

High performance self-aligned top-gate zinc oxide (ZnO) thin film transistors (TFTs) utilizing high-k Al₂O₃ thin film as gate dielectric are developed in this paper. Good quality Al₂O₃ thin film was deposited by reactive DC magnetron sputtering technique using aluminum target in a mixed argon and oxygen ambient at room temperature. The resulting transistor exhibits a field effect mobility of 27 cm²/V s, a threshold voltage of − 0.5 V, a subthreshold swing of 0.12 V/decade and an on/off current ratio of 9 × 10⁶. The proposed top-gate ZnO TFTs in this paper can act as driving devices in the next generation flat panel displays.     

Effect of gallium content on bias stress stability of solution-deposited Ga-Sn-Zn-O semiconductor transistors

We generated solution-processed thin film transistor (TFTs) using gallium tin zinc oxide (GTZO, Ga-Sn-Zn-O) layers as the channel that exhibit improved bias-stress stability during device operation under ambient conditions. The cause of the bias-stress stability was investigated through comparisons with zinc tin oxide (ZTO, Zn-Sn-O)-based TFTs, which suffer red from bias stress instability. Based on in-depth analysis of the electrical characteristics and chemical structure of both GTZO and ZTO layers, it was discovered that the GTZO layers had a significantly lower oxygen vacancy concentration than did the ZTO layer, which influenced the electrical performance of the GTZO transistors as well as their bias-stress stability. When 5 mol% gallium was added, a bias stress-stable transistor was obtained, exhibiting typical semiconductor behavior with a field-effect mobility of 1.2 cm² V^− 1 s^− 1, on/off ratio of 10⁶, off-current of 1 × 10^− 10 A, and threshold voltage of 19.6 V. Further doping of Ga deteriorated the device performance, which was found to be associated with decreased carrier concentration and segregation of an insulating secondary phase.