Effects of Powder Characteristics on Electrodischarge Machining Efficiency

This paper presents the effects of various powder characteristics on the efficiency of electrodischarge machining (EDM) SKD-11. The additives examined include aluminium (Al), chromium (Cr), copper (Cu), and silicon carbide (SiC) powders that have significant differences in their thermophysical properties. The machining mechanism with the addition of the foreign particles, the tool wear rate (TWR), and the material removal rate (MRR) have been investigated. It was found experimentally that the particle concentration, the particle size, the particle density, the electrical resistivity, and the thermal conductivity of powders were important characteristics that significantly affected the machining performance in the EDM process. Proper addition of powders to the dielectric fluid increased the MRR and, thus, decreased the TWR. Under the same particle concentration experiments, the smallest suspended particle size led to the greatest MRR and, thus, the lowest TWR. Of the additives investigated, chromium powder produced the greatest MRR and the lowest TWR, whereas the process without foreign particles has the converse effects. The addition of copper powder to the dielectric fluid was found to make almost no difference to the pure kerosene EDM system.     

INVESTIGATING THE EFFECTS OF EDM PARAMETERS ON SURFACE INTEGRITY,MRR AND TWR IN MACHINING OF Ti–6Al–4V

Ti–6Al–4V is a kind of difficult-to-cut material with poor machinability by traditional machining methods, while electrical discharge machining (EDM) is suitable for machining titanium alloys. In this paper, three input machining parameters including pulse current, pulse on time and open circuit voltage were changed during EDM tests. To investigate the output characteristics; material removal rate (MRR), tool wear ratio (TWR) and different aspects of surface integrity for Ti–6Al–4V samples such as topography of machined surface, crack formation, white layer (recast layer) thickness and microhardness were considered as performance criteria. The variations of MRR and TWR versus input machining parameters were investigated by means of main and interaction effect plots and also verified by ANOVA results. The effect of pulse energy based on pulse on time and pulse current variations against recast layer thickness and microhardness was studied. The possibility of forming different chemical elements and compounds on the work surface after EDM process was investigated by EDS and XRD analyses. The experimental results revealed that general aspects of surface integrity for machined samples are mostly affected by pulse current and pulse on time. The approximate density of cracks, micro holes and pits on the work surface is intensively dependent on pulse energy variations. Although increase of pulse energy improves the material removal efficiency but leads to increase of average thickness and microhardness of recast layer.     

A study on electrode wear sensing and compensation in Micro-EDM using machine vision system

This paper presents an electrode wear compensation method based on a machine vision system for micro-electro-discharge machining (EDM). Front wear and corner wear of tool electrode can be measured and evaluated in a direct manner by the vision system’s image-processing software capabilities. Tool electrode images have depicted that the front wear and corner wear were increased rapidly during EDM drilling and EDM milling, respectively, and thus contributing to an arc and a tapering shape at the end of tool electrode, respectively. Both the depth of the hole and depth of the groove are linearly proportional to the length of the front wear. A new electrode wear compensation method is presented based on the direct measurement of the front wear. Experimental results not only verify the usefulness of the electrode wear compensation method in micro-EDM, they also demonstrate that the machining time can be significantly reduced by 40% when using the proposed method, compared to the uniform wear method.     

Investigation of emulsion for die sinking EDM

Machining fluid is a primary factor that affects the material removal rate, surface quality, and electrode wear of electrical discharge machining (EDM). Kerosene is the most commonly used working fluid in die sinking EDM, but it shows low ignition temperature and high volatility; if the improper operations are undertaken, it can cause conflagration. Using distilled water or pure water as the machining fluid in EDM, no fire hazard occurs, and the working environment is well; however, using distilled water or pure water as the machining fluid in EDM, the material removal rate of machining large surface is low, and the machine tool is easily eroded. Emulsion-1 and emulsion-2 used as working fluid in die sinking EDM are developed. The compositions of emulsion-1 and emulsion-2 are introduced. In comparison with kerosene, emulsion-1 and emulsion-2 used in EDM show high material removal rate, low surface roughness, high discharge gap, and good working environment. The electrode wear ratio in emulsion-1 is lower than that in kerosene. The electrode wear ratio in emulsion-2 is higher than that in kerosene. The effects of composition and concentration of emulsifier on the emulsion property and EDM performance have been investigated. The comparative tests of EDM performance with kerosene, emulsion-1, and emulsion-2 have been done.     

分散剂在电火花小孔加工中的作用机理及试验研究

从研究水分散剂的分散机理入手,分析研究了水分散剂对电火花小孔加工的排屑、加工速度和加工质量的影响。通过电火花小孔加工中采用自来水工作液和分散剂工作液的加工效果对比,发现在电火花小孔加工的水基工作液中加入一定比例的分散剂后,不仅使电火花小孔加工的加工速度提高、电极相对损耗降低,而且有效脉冲数增加,二次放电数明显减少,工具电极作用端和被加工孔的锥度变小,加工质量提高。     

Feasibility study of micro-slit EDM machining using pure water

This study addresses micro-slit EDM machining feasibility using pure water as the dielectric fluid. Experimental results revealed that pure water could be used as a dielectric fluid and adopting negative polarity EDM machining could obtain high material removal rate (MRR), low electrode wear, small slit expansion, and little machined burr, compared to positive polarity machining. In comparing kerosene versus pure water, pure water was observed to cause low carbon adherence to the electrode surface. Also discharge energy does not decrease and the discharge processes are not interrupted. Therefore, MRR was higher, and related electrode wear ratio compared to kerosene use was lower. In a continual EDM with multi-slit machining, kerosene will cause carbon element adherence, creating an initially high MRR and electrode wear, with rapid decline. However, pure water will not cause carbon element adherence on the electrode surface, so MRR and electrode wear is always stable in this process.     

Multi-response optimization of machining process parameters for powder mixed electro-discharge machining of H-11 die steel using grey relational analysis and topsis

Electro-discharge machining (EDM) is an enormously used nonconventional process for removing material in die making, aerospace, and automobile industries. It consists of limitations like poor volumetric material removal rate (MRR) and reduced surface quality. Powder mixed EDM (PMEDM) is a new development in EDM to enhance its machining capabilities. The present work investigates the effect of powder concentration (C_p), peak current (I_p), pulse on time (T_on), duty cycle (DC) and gap voltage (V_g) on MRR, tool wear rate (TWR), electrode wear ratio (EWR), and surface roughness (SR) simultaneously for H-11 die steel using SiC powder. Taguchi's L₂₇ orthogonal array has been used to conduct the experiments. Multiobjective optimization using grey relational analysis (GRA) and technique for order of preference by similarity to ideal solution (TOPSIS) has been used to maximize the MRR and minimize the TWR, EWR, and SR and determine the optimal set of process parameters. Analysis of variance (ANOVA) has been performed to understand the significance of each process parameter. Results were verified by conducting confirmatory tests. GRA and TOPSIS exhibit an improvement of 0.1843 and 0.14308 in the preference values, respectively. Microstructure analysis has been done using scanning electron microscope (SEM) for the optimum set of parameters.     

Influence of parameters and optimization of EDM performance measures on MDN 300 steel using Taguchi method

Maraging steel (MDN 300) exhibits high levels of strength and hardness. Optimization of performance measures is essential for effective machining. In this paper, Taguchi method, used to determine the influence of process parameters and optimization of electrical discharge machining (EDM) performance measures on MDN 300 steel, has been discussed. The process performance criteria such as material removal rate (MRR), tool wear rate (TWR), relative wear ratio (RWR), and surface roughness (SR) were evaluated. Discharge current, pulse on time, and pulse off time have been considered the main factors affecting EDM performance. The results of the present work reveal that the optimal level of the factors for SR and TWR are same but differs from the optimum levels of the factors for MRR and RWR. Further, discharge current, pulse on time, and pulse off time have been found to play a significant role in EDM operations. Detailed analysis of structural features of machined surface was done by using scanning electron microscope (SEM) to understand the influence of parameters. SEM of electrical discharge machining surface indicates that at higher discharge current and longer pulse on duration give rougher surface with more craters, globules of debris, pockmarks or chimneys, and microcracks than that of lower discharge current and lower pulse on duration.     

Effect of ultrasonic vibration of tool on electrical discharge machining of cemented tungsten carbide (WC-Co)

This paper deals with the effect of copper tool vibration with ultrasonic (US) frequency on the electrical discharge machining (EDM) characteristics of cemented tungsten carbide (WC-Co). It was found that ultrasonic vibration of the tool (USVT) was more effective in attaining a high material removal rate (MRR) when working under low discharge currents and low pulse times (finishing regimes). In general, the surface roughness and the tool wear ratio (TWR) were increased when ultrasonic vibration was employed. It was observed that application of ultrasonic vibration significantly reduced arcing and open circuit pulses, and the stability of the process had a remarkable improvement. This study showed that, there were optimum conditions for ultrasonic assisted machining of cemented tungsten carbide, although the conditions may vary by giving other input parameters for those which had been set constant in the present work.     

A study of die helical thread cavity surface finish made by Cu-W electrodes with planetary EDM

An experimental research study intended for the application of a planetary electrical discharge machining (EDM) process with copper-tungsten (Cu-W) electrodes in the surface micro-finishing of die helical thread cavities made with AISI H13 tool steel full-hardened at 53 HRC is presented. To establish the EDM parameters’ effect on various surface finishing aspects and metallurgical transformations, three tool electrode Cu-W compositions are selected, and operating parameters such as the open-circuit voltage (U ₀), the discharge voltage (u _e), the peak discharge current (î _e), the pulse-on duration (t _i), the duty factor (τ) and the dielectric flushing pressure (p _in), are correlated. The researched machining characteristics are the material removal rate (MRR—V _w), the relative tool wear ratio (TWR—?), the workpiece surface roughness (SR—Ra), the average white layer thickness (WLT—e _wl) and the heat-affected zone (HAZ—Z _ha). An empirical relation between the surface roughness (SR—Ra) and the energy per discharge (W _e) has been determined. It is analysed that copper-tungsten electrodes with negative polarity are appropriate for planetary EDM die steel surface micro-finishing, allowing the attaining of good geometry accuracy and sharp details. For die steel precision EDM, the relative wear ratio optimum condition and minor surface roughness takes place at a gap voltage of 280 V, discharge current of 0.5–1.0 A, pulse-on duration of 0.8 μs, duty factor of 50%, dielectric flushing pressure of 40 kPa and copper tungsten (Cu20W80) as the tool electrode material with negative polarity. The copper-tungsten electrode’s low material removal rate and low tool-wear ratio allows the machining of EDM cavity surfaces with an accurate geometry and a “mirror-like” surface micro-finishing. A planetary EDM application to manufacture helical thread cavities in steel dies for polymer injection is presented. Conclusions are appointed for the planetary EDM of helical thread cavities with Cu-W electrodes validating the accomplishment as a novel technique for manufacturing processes.     

Micro-hole Maching of Copper Using the Electro-discharge Machining Process with a Tungsten Carbide Electrode Compared with a Copper Electrode

This paper describes micro-hole machining of a copper plate using the electro-discharge machining (EDM) process. Tungsten carbide was selected as the material for the electrode and compared with a copper-electrode. A precision centreless grinding process was employed to grind the electrode down to the desired diameter. A series of experiments were performed on a traditional EDM machine to investigate the effects of electrode material polarity setting and of a rotating electrode. Results have shown that electrode wear and hole enlargement are both smaller when positive polarity machining is selected; whereas electrode wear is larger and machining speed is higher when negative polarity machining is selected. High-quality micro-hole machining in copper can be achieved by the proposed method.     

Optimization of machining parameters in rotary EDM process by using the Taguchi method

Electrical discharge machining (EDM) is one of the advanced methods of machining. Most publications on the EDM process are directed towards non-rotational tools. But rotation of the tool provides a good flushing in the machining zone. In this study, the optimal setting of the process parameters on rotary EDM was determined. A total of three variables of peak current, pulse on time, and rotational speed of the tool with three types of electrode were considered as machining parameters. Then some experiments have been performed by using Taguchi's method to evaluate the effects of input parameters on material removal rate, electrode wear rate, surface roughness, and overcut. Moreover, the optimal setting of the parameters was determined through experiments planned, conducted, and analyzed using the Taguchi method. Results indicate that the model has an acceptable performance to optimize the rotary EDM process.     

Error calculation for corrective machining with allowance requirements

Electroforming copper from the copper sulfate baths or the pyrophosphate baths is one of commonly used methods for manufacturing electro-discharge machining (EDM) tool electrode, in particular for the fabrication of micro- and meso-scale tool electrodes with complex cross-section, but few literature on the electrode-wear performance of electroformed copper electrode has been available until today. To better select copper tool electrode materials, the wear resistance of the macroscopic and tiny copper tool electrodes deposited from the copper sulfate baths and the pyrophosphate baths were investigated comparatively with the same micro-EDM parameters. The optimal electrodeposition parameters in which the deposited copper had the lowest electrode-wear ratio were first obtained from the two baths, respectively. And then, the wear resistance of the micro-featured copper tool electrode electroformed using the optimal deposition conditions from the two baths were evaluated comparatively. Experimental investigations showed that, both at the macro-scale level and at the micro-scale level, the copper tool electrode electroformed from the pyrophosphate baths (the smallest electrode-wear ratio was 10% for the macro-electrode and 12.8% for the micro-electrode) exhibited better wear resistance than that deposited from the copper sulfate baths (the smallest electrode-wear ratio was 11.95% for the macro-electrode and 17.3% for the micro-electrode).     

4Cr5MoVSi电火花加工试验特征规律研究

采用紫铜工具电极,在峰值电流为4-24A、脉冲宽度为25-200μs、加工电压为80-200V的电参数范围内,综合应用因子试验和正交试验方法,对难加工材料4Cr5MoVSi进行了电火花加工试验。在进行电加工基础特征规律分析的基础上,考查了电参数对加工速度、双边侧面放电间隙、电极损耗的影响,并对电火花加工机理进行了分析。研究结果表明:采用紫铜电极电火花加工4Cr5MoVSi,在本试验范围内,峰值电流Ip与脉冲宽度ti、加工电压U、脉冲间隔t0存在一定的交互作用;与其它三个因素相比,峰值电流对加工速度、电极损耗、双边侧面放电间隙的影响更显著;随脉冲宽度和加工电压的增大,电极损耗逐渐减小。     

Investigations into the effect of tool shapes with size factor consideration in sink electrical discharge machining (EDM) process

In sink electric discharge machining (EDM) process, the tool shape and size along with wear are of great importance because they adversely affect the accuracy of machined features. This paper presents the application of response surface methodology (RSM) for investigating the effect of tool shapes such as triangular, square, rectangular, and circular with size factor consideration along with other process parameters like discharge current, pulse on-time, pulse off-time, and tool area. The RSM-based mathematical models of material removal rate (MRR) and tool wear rate (TWR) have been developed using the data obtained through central composite design. The analysis of variance was applied to verify the lack of fit and adequacy of the developed models. Further, the confirmation tests were performed to ascertain the accuracy of the developed models. The investigations revealed that the best tool shape for higher MRR and lower TWR is circular, followed by triangular, rectangular, and square cross sections. From the parametric analysis, it is also observed that the interaction effect of discharge current and pulse on-time is highly significant on MRR and TWR, whereas the main factors such as pulse off-time and tool area are statistically significant on MRR and TWR.     

Investigation of near dry EDM compared with wet and dry EDM processes

Journal of Mechanical Science and Technology - Material removal rate (MRR), tool wear ratio (TWR) and surface roughness (SR) obtained by near-dry EDM process were compared with wet and dry EDM at...     

Analysis of the machining characteristics of EDM as functions of the mobilities of electrons and ions

Electrical discharge machining (EDM) is a process that can be used effectively to machine conductive metals regardless of their hardness. In the EDM process, material removal occurs because of the thermal energy of the plasma channel between the electrode and the workpiece. During EDM, the electrode as well as the workpiece is abraded by the thermal energy. Tool wear adversely affects the machining accuracy and increases tooling costs. Many previous studies have focused on mitigating the problems of tool wear by investigating various EDM parameters. In this study, the tool wear problem was investigated on the basis of the mobilities of electrons and ions in the plasma channel. The material removal volumes of both the electrode and the workpiece were compared as functions of the gap voltage. The material removal difference according to the capacitance was also investigated. The tool wear ratio was calculated under different EDM condition and an EDM conditions for reducing the tool wear ratio was suggested.     

弯曲孔电加工工艺的实验研究

实验研究探讨了一种使用线框电极的电火花套料加工的新工艺.根据正交试验方法来分析精加工时加工参数对加工速度、电极损耗和加工表面粗糙度的影响,以确定套料精加工时最佳的电规准参数.依据直孔套料加工参数在模具材料中加工出了圆弧弯曲孔.     

A method to predict possibility of arcing in EDM of TiB2p reinforced ferrous matrix composite

Electrical Discharge Machining (EDM) is very popular for machining conductive metal matrix composites (MMCs) because the hardness rendered by the ceramic reinforcements to these composites causes very high tool wear and cutting forces in conventional machining processes. EDM requires selection of a number of parameters for desirable results. Inappropriate parameter selection can lead to high overcuts, tool wear, excessive roughness, and arcing during machining and adversely affect machining quality. Arcing leads to short circuit gap conditions resulting in large energy discharges and uncontrolled machining. Arcing is a detrimental phenomenon in EDM which causes spoiling of workpiece and tool electrode and tends to damage the power supply of EDM machine. Parameter combinations that lead to arcing during machining have to be identified and avoided for every tool, work material, and dielectric combination. Proper selection of parameter combinations to avoid arcing is essential in EDM. In the work, experiments were conducted using L27 design of experiment to determine the parameter settings which cause arcing in EDM machining of TiB₂p reinforced ferrous matrix composite. Important EDM process parameters were selected in roughing, intermediate, and finishing range so as to study the occurrence of arcing. Using the experimental data, an artificial neural network (ANN) model was developed as a tool to predict the possibility of arcing for selected parameter combinations. This model can help avoid the parameter combinations which can lead to arcing during actual machining using EDM. The ANN model was validated by conducting validation experiments to ensure that it can work accurately as a predicting tool to know beforehand whether the selected parameters will lead to arcing during actual machining using EDM. Validation results show that the ANN model developed can predict arcing possibility accurately when the depth of machining is included as input variable for the model.     

EDM electrode manufacturing using RP combining electroless plating with electroforming

This study investigates an effective method for manufacturing electrical discharge machining (EDM) electrodes using the rapid prototyping (RP) system based on electroless plating (nickel plating) and electroforming (copper). This method was shown to finish the development of die-sinking electrical discharge machining (EDM) electrodes, shorten the electrode manufacturing process, decrease the manufacturing duration as well as the cost of electrodes. The electrode prototype was drawn with Pro/E 3D CAD, and the CAD model was then transformed into the stereo lithography (STL) file format. A Zcorp 402 3DP rapid prototyping machine was adopted to make a gypsum powder electrode prototype with a complex appearance. The gypsum material is sealed by resin permeation, enhancing its water-resistance and strength. Electroless plating was then performed to introduce electric conductivity onto the gypsum electrode surface, followed by copper electroforming of the thickness about 1 mm to obtain the EDM electrode. Furthermore, die-sinking electric discharge machining was performed. Test results indicate that no crack was found on the electrode and that the electrical discharge machining effects are promising.