Design for Shear in Curved Composite Multiple Steel Box Girder Bridges

Modern highway bridges are often subject to tight geometric restrictions and, in many cases, must be built in curved alignment. These bridges may have a cross section in the form of a multiple steel box girder composite with a concrete deck slab. This type of cross section is one of the most suitable for resisting the torsional, distortional, and warping effects induced by the bridge’s curvature. Current design practice in North America does not specifically deal with shear distribution in horizontally curved composite multiple steel box girder bridges. In this paper an extensive parametric study, using an experimentally calibrated finite-element model, is presented, in which simply supported straight and curved prototype bridges are analyzed to determine their shear distribution characteristics under dead load and under AASHTO live loadings. The parameters considered in this study are span length, number of steel boxes, number of traffic lanes, bridge aspect ratio, degree of curvature, and number and stiffness of cross bracings and of top-chord systems. Results from tests on five box girder bridge models verify the finite-element model. Based on the results from the parametric study simple empirical formulas for maximum shears (reactions) are developed that are suitable for the design office. A comparison is made with AASHTO and CHBDC formulas for straight bridges. An illustrative example of the design is presented.     

Experimental and Analytical Studies of a Horizontally Curved Steel I-Girder Bridge during Erection

A series of studies on an experimental, full-scale curved steel bridge structure during erection are discussed. The work was part of the Federal Highway Administration’s curved steel bridge research project (CSBRP). The CSBRP is intended to improve the understanding of curved bridge behavior and to develop more rational design guidelines. The main purpose of the studies reported herein was to assess the capability of analytical tools for predicting response during erection. Nine erection studies, examining six different framing plans, are presented. The framing plans are not necessarily representative of curved bridge subassemblies as they would be erected in the field; however, they represent a variety of conditions that would test the robustness of analysis tools and assess the importance of erection sequence on initial stresses in a curved girder bridge. The simply supported, three I-girder system used for the tests is described and methods for reducing and examining the data are discussed. Comparisons between experimental and analytical results demonstrate that analysis tools can predict loads and deformations during construction. Comparison to the V-load method indicates that it predicts stresses in exterior girders well, but can underpredict them for interior girders.     

Effect of Multilanes on Wheel Load Distribution in Steel Girder Bridges

This paper presents the results of a parametric study that investigated the effect of multilanes and continuity on wheel load distribution in steel girder bridges. Typical one- and two-span, two-, three-, and four-lane, straight, composite steel girder bridges were selected for this study. The major bridge parameters chosen for this study were the span length, girder spacing, one- versus two-spans, and the number of lanes. These parameters were varied within practical ranges to study their influence on the wheel load distribution factors. A total of 144 bridges were analyzed using the finite-element method. The computer program, SAP90, was used to model the concrete slab as quadrilateral shell elements and the steel girders as space frame members. Simple supports were used to model the boundary conditions. AASHTO HS20 design trucks were positioned in all lanes of the one- and two-span bridges to produce the maximum bending moments. The calculated finite-element wheel load distribution factors were compared with the AASHTO and the National Cooperative Highway Research Program (NCHRP) 12-26 formulas. The results of this parametric study agree with the newly developed NCHRP 12-26 formula and both were, in general, less than the empirical AASHTO formula (S∕5.5) for longer span lengths [>15.25 m (50 ft)] and girder spacing >1.8 m (6 ft). This paper demonstrates that the multiple lane reduction factors are built into the newly developed distribution factors for steel girder bridges that were presented in the NCHRP 12-26 final report. It should be noted that AASHTO LRFD contains a similar expression that results in a value that is 50% of the value in the equations developed as a part of NCHRP 12-26. This is due to the fact that AASHTO LRFD consider the entire design truck instead of half-truck (wheel loads) as the case in the NCHRP 12-26 report and the AASHTO Standard Specifications for Highway Bridges. Therefore, this paper supports the use of the new distribution factors for steel girder bridges developed as a part of NCHRP 12-26 and consequently the distribution factors presented in the AASHTO LRFD Bridge Design Specifications.     

The beta-adrenomimetic effect of human and animal blood serum

The conventional analysis and design of highway bridges ignore the contribution of sidewalks and∕or railings in a bridge deck when calculating the flexural strength of superstructures. The presence of sidewalks and railings or parapets acting integrally with the bridge deck have the effect of stiffening the outside girders and attracting more load while reducing the load effects in the interior girders. This paper presents the results of a parametric study showing the influence of typical sidewalks and railings on wheel load distribution as well as on the load-carrying capacity of highway bridges. A typical one-span, two-lane, simply supported, composite steel girder bridge was selected in order to investigate the influence of various parameters such as: span length, girder spacing, sidewalks, and railings. A total of 120 bridges were analyzed using three-dimensional finite-element analysis. American Association of State Highway and Transportation Officials (AASHTO) HS20 design trucks were positioned in both lanes to produce the maximum moments. The finite-element analysis results were also compared with AASHTO wheel load distribution factors. The AASHTO load and resistance factor design (LRFD) wheel load distribution formula correlated conservatively with the finite-element results and all were less than the typical empirical formula (S∕5.5). The presence of sidewalks and railings were shown to increase the load-carrying capacity by as much as 30% if they were included in the strength evaluation of highway bridges.     

Examination of Level of Analysis Accuracy for Curved I-Girder Bridges through Comparisons to Field Data

To evaluate the accuracy of different levels of analysis used to predict horizontally curved steel I-girder bridge response, a field test was performed on a three-span structure. Collected strain data were reduced to determine girder vertical and bottom flange lateral bending moments. Experimental moments were compared to numerical moments obtained from three commonly employed levels of analysis. Level 1 analysis includes two manual calculation methods: a line girder analysis method described in the AASHTO Guide Specification for Horizontally Curved Highway Bridges, and the V-load method. Grillage models represent Level 2 and were created using three commercially available computer programs: SAP2000, MDX, and DESCUS. Level 3 consists of three-dimensional (3D) finite element models created using SAP2000 and the BSDI 3D system. Responses obtained from each level are compared and discussed for a single radial cross section of the structure, and the compared results involve truck loads and placement schemes that do not represent those used for bridge design. The field test and numerical data presented are used solely to determine the accuracy of each level of analysis for predicting structure response to a specific live load at a specific cross section. Results showed that Level 2 and Level 3 analyses predict girder vertical bending moment distributions more accurately than Level 1 analyses throughout the tested cross section. The comparisons indicate that Level 3 girder vertical bending moment distributions offered no appreciable increase in accuracy over Level 2 analyses. The study also indicates that both Level 1 and Level 3 analyses provide bottom flange lateral bending moment distributions that do not correlate well with field test results for the studied bridge cross section.     

Experimental Verification of Horizontally Curved I-Girder Bridge Behavior

Past research has been conducted on the behavior of horizontally curved girders by testing scaled models and full-scale laboratory bridges and by analyzing numerical models. Current design specifications are based on this past research; however, little field data of in-service bridges exist to support the findings of the past research on which the current design criteria are based. The purpose of the present study was to gather field response data from three in-service, curved, steel I-girder bridges to determine behavior when subjected to a test truck and normal truck traffic. Transverse bending distribution factors and dynamic load allowance were calculated from the data collected. Numerical grillage models of the three bridges were developed to determine if a simple numerical model will accurately predict actual field measured transverse bending distribution, deflections, and cross-frame and diaphragm shear forces. The present study found that AASHTO specifications are conservative for both dynamic load allowance and transverse bending moment distribution. The grillage models were found to predict with reasonable accuracy the behavior of a curved I-girder bridge.     

Wheel Load Distribution in Simply Supported Concrete Slab Bridges

This paper presents the results of a parametric study related to the wheel load distribution in one-span, simply supported, multilane, reinforced concrete slab bridges. The finite-element method was used to investigate the effect of span length, slab width with and without shoulders, and wheel load conditions on typical bridges. A total of 112 highway bridge case studies were analyzed. It was assumed that the bridges were stand-alone structures carrying one-way traffic. The finite-element analysis (FEA) results of one-, two-, three-, and four-lane bridges are presented in combination with four typical span lengths. Bridges were loaded with highway design truck HS20 placed at critical locations in the longitudinal direction of each lane. Two possible transverse truck positions were considered: (1) Centered loading condition where design trucks are assumed to be traveling in the center of each lane; and (2) edge loading condition where the design trucks are placed close to one edge of the slab with the absolute minimum spacing between adjacent trucks. FEA results for bridges subjected to edge loading showed that the AASHTO standard specifications procedure overestimates the bending moment by 30% for one lane and a span length less than 7.5 m (25 ft) but agrees with FEA bending moments for longer spans. The AASHTO bending moment gave results similar to those of the FEA when considering two or more lanes and a span length less than 10.5 m (35 ft). However, as the span length increases, AASHTO underestimates the FEA bending moment by 15 to 30%. It was shown that the presence of shoulders on both sides of the bridge increases the load-carrying capacity of the bridge due to the increase in slab width. An extreme loading scenario was created by introducing a disabled truck near the edge in addition to design trucks in other lanes placed as close as possible to the disabled truck. For this extreme loading condition, AASHTO procedure gave similar results to the FEA longitudinal bending moments for spans up to 7.5 m (25 ft) and underestimated the FEA (20 to 40%) for spans between 9 and 16.5 m (30 and 55 ft), regardless of the number of lanes. The new AASHTO load and resistance factor design (LRFD) bridge design specifications overestimate the bending moments for normal traffic on bridges. However, LRFD procedure gives results similar to those of the FEA edge+truck loading condition. Furthermore, the FEA results showed that edge beams must be considered in multilane slab bridges with a span length ranging between 6 and 16.5 m (20 and 55 ft). This paper will assist bridge engineers in performing realistic designs of simply supported, multilane, reinforced concrete slab bridges as well as evaluating the load-carrying capacity of existing highway bridges.     

Dynamic and Static Behavior of a Curved-Girder Bridge with Varying Boundary Conditions

A curved, three-span continuous, steel I-girder bridge in Salt Lake City was tested in order to determine its dynamic and static load carrying properties for three boundary condition states. For each of the three boundary condition states, two dynamic forced vibration methods were applied to the bridge as well as a static live-load test. The first forced vibration method used an eccentric mass shaker. The second method involved striking the side of the bridge with an impact hammer. The live-load test was performed by slowly driving a truck at a crawl speed across the bridge. Velocity transducers, accelerometers, and strain gauges were utilized to record the response of the bridge. The analysis and compilation of recorded dynamic response of the bridge enabled the preparation of mode shapes and natural frequencies for each boundary condition. This paper discusses the resulting changes in relevant dynamic properties and compares them with the changes in the static properties that were determined from the bridge response recorded from the live-load tests.     

Simply Supported Curved Cellular Bridges: Simplified Design Method

The use of curved composite bridges in interchanges of modern highway systems has become increasingly popular for economic and aesthetic considerations. Bridges with a concrete deck composite with a steel multicell section can adequately resist torsional and warping effects induced by high curvature. Although current design practices in North America recommend few analytical methods for the design of curved multicell box girder bridges, economical requirements in the design process point to a need for a simplified design method. This paper summarizes the results from an extensive parametric study, using the finite-element method, in which simply supported curved composite multicell bridge prototypes are analyzed to evaluate the moment and deflection distributions between girders, as well as the axial forces expected in the bracing system, due to truck loading as well as dead load. Results from tests on four, 1∕12 linear-scale, simply supported curved composite concrete deck-steel multicell bridge models are used to substantiate and verify the analytical modeling. The parameters considered in the study are cross-bracing system, aspect ratio, number of lanes, number of cells, and degree of curvature. Based on the data generated from the parametric study, expressions for moment and deflection distribution factors are deduced. Expressions for the maximum axial force in bracing members are also derived. An illustrative design example is presented.     

Construction of a Horizontally Curved Steel I-Girder Bridge. Part II: Inconsistent Detailing

The erection of horizontally curved steel I-girder bridges tends to be more complex than the erection of straight steel I-girder bridges. The erection of a curved steel I-girder bridge can be further complicated when the cross-frame members and girders are detailed inconsistently in an effort to force bridge components into some desirable geometric condition. Inconsistent detailing involves the intentional specification of cross-frame members that are either too long or too short to align with girder connector plates properly so as to force the girders into a given position, resulting in connection misalignments that must be resolved by applying external forces to the bridge components. The current research investigates the erection of a recently constructed horizontally curved steel I-girder bridge and highlights the fact that practice of inconsistent detailing can lead to very formidable and costly fit-up problems in the field; especially when girder sizes are large.     

Evaluation of Live-Load Lateral Flange Bending Distribution for a Horizontally Curved I-Girder Bridge

This paper focuses on levels of live-load lateral bending moment (bimoment) distribution in a horizontally curved steel I-girder bridge. Work centered primarily on the examination of (1) data from field testing of an in-service horizontally curved steel I-girder bridge and (2) results from a three-dimensional numerical model. Experimental data sets were used for calibration of the numerical model and the calibrated model was then used to examine the accuracy of lateral bending distribution factor equations presented in the 1993 Edition of the (AASHTO) Guide Specifications for Horizontally Curved Bridges. It is of interest to examine these equations for potential use in preliminary design even though they have been eliminated during recent AASHTO specification modifications that addressed curved bridge analysis, the 2005 Interims to the AASHTO LRFD Bridge Design Specifications. In addition, they were developed using idealized computer models and small-scale laboratory testing with very few field tests of in-service full-scale curved steel bridges conducted to support or refute their use. Results from such experimental and numerical studies are presented and discussed herein.     

Enhancement of Flexural Design of Horizontally Curved Prestressed Bridges

In this paper, flexural behavior of horizontally curved prestressed (posttensioned) box bridges is studied by using three-dimensional and refined finite-element modeling and analysis. Bridge length, section geometry, and material properties are the same in all the models, while angle of curvature varies from 0 to 90°. The results of analysis show that in curved bridges, stress distribution is significantly different in comparison to straight bridges. Also, the level of stresses at some locations of section width is considerably high. It is proposed to vary the distribution of the prestressing tendons across section width in order to optimize the bridge capacity. Results show that by proper redistribution of prestressing in section width, significant reduction in resultant stress is possible.     

Integral Abutment Bridge Behavior: Parametric Analysis of a Massachusetts Bridge

Integral abutment bridges are often a preferred bridge type for moderate spans throughout the United States. However, design methods and construction details vary from state to state. Variations between states are noted in the methods employed to accommodate deformations in the piles. The significance of these differences was evaluated through a finite-element study. The effects of backfill properties and soil restraint on piles were evaluated with regard to bridge distortions and maximum moment realized in the piles. Results show that bridge expansion is predominantly affected by backfill conditions, whereas contraction is influenced by pile restraint conditions. Pile moments are minimized when denser backfill and lower pile restraint are provided. The influence of abutment soil-structure spring modeling assumptions is addressed. Models were calibrated to the reference bridge at Orange-Wendell, Mass, which has been instrumented and data collected for 4 years.     

Construction of a Horizontally Curved Steel I-Girder Bridge. Part I: Erection Sequence

In the case of horizontally curved steel I-girder bridges, girder and cross-frame members are frequently detailed for erection in the no-load condition as a matter of convention. As a result, it is imperative that the erection sequence used to construct such bridges be comprehensively studied to ensure that the no-load condition can be achieved in the field and that significant superstructure component fit-up problems do not occur. The current research investigates the erection of a recently constructed horizontally curved steel I-girder bridge, in which significant difficulties were encountered during erection. The bridge erection is recreated through an analytical simulation using a detailed nonlinear finite element model. The analytical results demonstrate that a condition that closely resembles the no-load condition can be achieved in the field during construction with the proper implementation of temporary support structures; and that the difficulties encountered during the erection of the subject bridge superstructure could not be attributed to the erection scheme followed.     

Impact Factors for Curved Continuous Composite Multiple-Box Girder Bridges

The results from a parametric study on the impact factors for 180 curved continuous composite multiple-box girder bridges are presented. Expressions for the impact factors for tangential flexural stresses, deflection, shear forces and reactions are deduced for AASHTO truck loading. The finite-element method was utilized to model the bridges as three-dimensional structures. The vehicle axle used in the analysis was simulated as a pair of concentrated forces moving along the concrete deck in a circumferential path with a constant speed. The effects of bridge configurations, loading positions, and vehicle speed on the impact factors were examined. Bridge configurations included span length, span-to-radius of curvature ratio, number of lanes, and number of boxes. The effect of the mass of the vehicle on the dynamic response of the bridges is also investigated. The data generated from the parametric study and the deduced expressions for the impact factors would enable bridge engineers to design curved continuous composite multiple-box girder bridges more reliably and economically.     

Full-Scale Test and Analysis of a Curved Steel-Box Girder Bridge

Since the first edition of the AASHTO Guide Specifications for Horizontally Curved Steel Girder Highway Bridges was published in 1980, there have been two more editions including many revisions to the specifications. Some changes were based on valid research results and others were based on limited or uncertain research results and information. The current edition of the specifications contains provisions that may result in unreasonably conservative load capacity ratings. In this paper, the results of field tests and analyses conducted on the Veterans’ Memorial curved steel-box girder bridge are discussed. Test and analytical results show: (1) current AASHTO guide specifications regarding the first transverse stiffener spacing at the simple end support of a curved girder may be too conservative for bridge load capacity ratings; (2) current AASHTO guide specifications may greatly overestimate the dynamic loadings of curved box girder bridges with long span lengths; and (3) a plane grid finite-element model of about 20 elements per span in the longitudinal direction can be used to analyze curved multigirder bridges with external bracings located only over supports. The research results are instructive and applicable to bridge design and bridge load-rating activities.     

Development and Implementation of a Continuous Strain Monitoring System on a Multi-Girder Composite Steel Bridge

This paper describes the implementation and evaluation of a long-term strain monitoring system on a three-span, multisteel girder composite bridge located on the interstate system. The bridge is part of a network of bridges that are currently being monitored in Connecticut. The three steel girders are simply supported, whereas the concrete slab is continuous over the interior supports. The bridge has been analyzed using the standard AASHTO Specifications and the analytical predictions have been compared with the field monitoring results. The study has included determination of the location of the neutral axes and the evaluation of the load distributions to the different girders when large trucks cross the bridge. A finite-element analysis of the bridge has been carried out to further study the distribution of live load stresses in the steel girders and to study how continuity of the slabs at the interior joints would influence the overall behavior. The results of the continuous data collection are being used to evaluate the influence of truck traffic on the bridge and to establish a baseline for long-term monitoring.     

Lateral Load Distribution in Curved Steel I-Girder Bridges

The purpose of this paper is to develop new formulas for live load distribution in horizontally curved steel I-girder bridges. The formulas are developed by utilizing computer model results for a number of different horizontally curved steel I-girder bridges. The bridges used in this study are modeled as generalized grillage beam systems composed of horizontally curved beam elements for steel girders and substructure elements for lateral wind bracing and cross frames which consist of truss elements. Warping torsion is taken into consideration in the analysis. The effect of numerous parameters, including radius of curvature, girder spacing, overhang, etc., on the load distribution are studied. Key parameters affecting live load distribution are identified and simplified formulas are developed to predict positive moment, negative moment, and shear distribution for one-lane and multiple-lane loading. Comparisons of the formulas with finite element method and grillage analysis show that the proposed formulas have more accurate results than the various available American Association of State Highway and Transportation Officials specifications. The formulas developed in this study will assist bridge engineers and researchers in predicting the actual live load distribution in horizontally curved steel I-girder bridges.     

Live-Load Distribution Factors in Prestressed Concrete Girder Bridges

This paper presents an evaluation of flexural live-load distribution factors for a series of three-span prestressed concrete girder bridges. The response of one bridge, measured during a static live-load test, was used to evaluate the reliability of a finite-element model scheme. Twenty-four variations of this model were then used to evaluate the procedures for computing flexural live-load distribution factors that are embodied in three bridge design codes. The finite-element models were also used to investigate the effects that lifts, intermediate diaphragms, end diaphragms, continuity, skew angle, and load type have on distribution factors. For geometries similar to those considered in the development of the American Association of State Highway and Transportation Officials Load and Resistance Factor Design Specifications, the distribution factors computed with the finite-element models were within 6% of the code values. However, for the geometry of the bridge that was tested, the discrepancy was 28%. Lifts, end diaphragms, skew angle, and load type significantly decreased the distribution factors, while continuity and intermediate diaphragms had the least effect. If the bridge had been designed using the distribution factors calculated with the finite-element model rather than the code values, the required concrete release strength could have been reduced by 6.9 MPa (1,000 psi) or the live load could have been increased by 39%.     

Solver and Shell Element Performances for Curved Bridge Analysis

A study has been undertaken to investigate different solver and shell element performances for curved bridge finite-element analysis. Three sparse solvers were implemented into a bridge finite-element analysis code, and the solution times and memory requirements for typical bridges were compared. In addition, the use of four-node and nine-node shell elements in modeling was investigated for different mesh densities. Based on the comparative studies performed, modeling guidelines for practicing engineers have been developed and are presented herein.