Shear Strengthening Masonry Panels with Sheet Glass-Fiber Reinforced Polymer

This paper investigates strengthening masonry walls using glass-fiber reinforced polymer (GFRP) sheets. An experimental research program was undertaken. Both clay and concrete brick specimens were tested, with and without GFRP strengthening. Single-sided strengthening was considered, as it is often not practicable to apply the reinforcement to both sides of a wall. Static tests were carried out on six masonry panels, under a combination of vertical preload, and in-plane horizontal shear loading. The mechanisms by which load was carried were observed, varying from the initial, uncracked state, to the final, fully cracked state. The results demonstrate that a significant increase of the in-plane shear capacity of masonry can be achieved by bonding GFRP sheets to the surface of masonry walls. The experimental data were used to assess the effectiveness of the GFRP strengthening, and suggestions are made to allow the test results to be used in the design of sheet GFRP strengthening for masonry structures.     

Strengthening of Infill Masonry Walls with FRP Materials

This paper evaluates the effectiveness of different externally bonded glass fiber–reinforced polymer (GFRP) systems for increasing the out-of-plane resistance of infill masonry walls to loading. The research included a comprehensive experimental program comprising 14 full-scale specimens, including four unstrengthened (control) specimens and 10 strengthened specimens. To simulate the boundary conditions of infill walls, all specimens consisted of a reinforced concrete (RC) frame, simulating the supporting RC elements of a building superstructure, which was infilled with solid concrete brick masonry. The specimens were loaded out-of-plane using uniformly distributed pressure to simulate the differential (suction) pressure induced by a tornado. Parameters investigated in the experimental program included aspect ratio, FRP coverage ratio, number of masonry wythes, and type of FRP anchorage. Test results indicated that the type of FRP anchorage had a significant effect on the failure mode. Research findings concluded that GFRP strengthening of infill masonry walls is effective in increasing the out-of-plane load-carrying capacity when proper anchorage of the FRP laminate is provided.     

Retrofitting of Deficient RC Cantilever Slabs Using GFRP Strips

Despite many studies on beams and slabs strengthened using fiber-reinforced plastic (FRP) plates, no study has been reported on the strengthening of RC cantilever slabs (e.g., canopies and balconies) using FRP materials. This paper presents the results of an experimental study of the feasibility of strengthening deficient RC cantilever slabs by bonding glass FRP (GFRP) strips∕sheets on the top surface (the tension side). As the key to the success of this strengthening method is a proper way of anchoring the GFRP strips into the supporting wall and the slab, the effectiveness of different anchorage systems was the focus of the experiments. Based on the test results, a simple and effective method is identified in which the GFRP strips are anchored into the walls through horizontal slots and onto the slab using fiber anchors.     

Assessment of Design Formulas for In-Plane FRP Strengthening of Masonry Walls

Masonry structures have demonstrated their seismic vulnerability during recent world seismic events. This paper investigates in-plane seismic performance of unreinforced masonry (URM) walls before and after they are retrofit using fiber-reinforced polymer (FRP) materials. An assessment of available design formulas for evaluating both the in-plane performance of URM walls and the contribution of FRP strengthening systems was performed. Walls with two configurations of the FRP reinforcement have been analyzed: one based on FRP strips installed parallel to the mortar joints, the other characterized by FRP strips arranged along the diagonals of the wall. Based on shear–compression tests carried out on FRP-strengthened masonry walls available in the literature, a comparison between theoretical and experimental data is performed. A discussion about the FRP strains at failure of the walls is provided and values of effective FRP strains to be used for design purposes are proposed.     

Experimental Evaluation of a Sacrificial Seismic Fuse Device for Masonry Infill Walls

Presented herein are the details and results of an experimental study conducted to evaluate the performance of a proposed infill wall fuse system. The purpose of this system, referred to as the seismic infill wall isolator subframe (SIWIS) system, is to prevent damage to columns or infill walls due to infill-frame interaction through a “sacrificial” component or a “structural fuse.” The SIWIS system conceptually consists of two vertical and one horizontal sandwiched light-gauge steel studs with SIWIS elements in the vertical members. The experimental study presented here involves the in-plane lateral load testing of a two-bay three-story steel frame in three forms of bare frame, infilled braced frame, and pinned frame equipped with the proposed SIWIS device. In addition, a brick wall in-plane strength test and a series of component tests on three different designs for fuse element were conducted. In the conducted tests, the suggested technique initially engages the infill walls in seismic resistance of the frame, but ultimately isolates them. It is concluded, thus, that the proposed fuse system has the potential for the development of an effective way to reduce earthquake damage in framed buildings with infill walls.     

Cyclic Flexure Tests of Masonry Walls Reinforced with Glass Fiber Reinforced Polymer Sheets

The research work reported here investigates the out-of-plane flexural behavior of masonry walls reinforced externally with glass fiber reinforced polymer (GFRP) sheets and subjected to cyclic loading. A full-scale test program consisting of eight wall specimens was conducted. Nine tests were performed, in which three parameters were studied. These included the level of compressive axial load, amount of internal steel reinforcement, and amount of externally bonded GFRP sheet reinforcement. Of the three parameters studied, varying the amount of GFRP sheets was the only parameter that significantly affected the behavior of the walls. The GFRP sheet reinforcement governed the linear response of the bending moment versus centerline deflection hysteresis. Increasing or decreasing the amount of GFRP sheet reinforcement either increased or decreased both the wall stiffness and the ultimate strength, respectively. Except for visible cracks, the walls maintained their structural integrity throughout the out-of-plane cyclic loading. The unloading/reloading paths for successive loading cycles were similar, indicating little degradation. Thus, the general behavior of the walls was very predictable. The system, therefore, could be used to advantageously rehabilitate older masonry structures that are inadequately reinforced to withstand seismic events. A simple model of the behavior is also presented to allow for the evaluation of the strength and deformation characteristics of these elements.     

Tests on Seismically Damaged Reinforced Concrete Walls Repaired and Strengthened Using Fiber-Reinforced Polymers

The behavior of six 1:2.5-scale reinforced concrete cantilever wall specimens having an aspect ratio of 1.5, tested to failure and subsequently repaired and strengthened using fiber-reinforced polymer (FRP) sheets is investigated. Specimens were first repaired by removing heavily cracked concrete, lap splicing the fractured steel bars by welding new short bars, placing new hoops and horizontal web reinforcement, and finally casting nonshrink high-strength repair mortar. The specimens were then strengthened using FRP sheets and strips, with a view to increasing flexural as well as shear strength and ductility. In addition to different arrangements of steel and FRP reinforcement in the walls, a key parameter was the way carbon-FRP strips added for flexural strengthening were anchored; steel plates and steel angles were used to this effect. Steel plates were anchored using U-shaped glass-FRP (GFRP) strips or bonded metal anchors. Test results have shown that by using FRP reinforcement, the flexural and shear strength of the specimens can be increased. From the anchorage systems tested, metal plates combined with FRP strips appear to be quite efficient. The effectiveness of the bonded metal anchors used was generally less than that of the combination of plates and GFRP strips. In all cases, final failure of the FRP anchorage is brittle, but only occurs after the peak strength is attained and typically follows the fracture of steel reinforcement in critical areas, hence the overall behavior of the strengthened walls is moderately ductile.     

CFRP Composite Connector for Concrete Members

Steel plate connections are frequently used in tilt-up and precast concrete building construction to tie adjacent wall panels together for shear and overturning effects, and to provide continuous diaphragm chord connections for wind and seismic loading. These welded connectors perform poorly in regions of high seismicity and are vulnerable to corrosion. Until now, retrofit and repair strategies for in-plane shear transfer strengthening were limited to attaching steel sections across panel edges. In the present paper, an experimental program is described that utilizes carbon fiber reinforced plastic (CFRP) composites to develop a viable retrofit scheme for precast concrete shear walls and diaphragms. Nine full-scale precast wall panel assemblies with CFRP composite connectors have been tested. The results show that the CFRP composite connection is an effective solution for the seismic retrofit and repair of precast concrete wall assemblies and other precast concrete elements, such as horizontal diaphragms, that require in-plane shear transfer strengthening.     

Tests on Seismically Damaged Reinforced Concrete Structural Walls Repaired Using Fiber-Reinforced Polymers

This paper presents the results of an experimental study on the seismic performance of axially loaded reinforced concrete (RC) walls with boundary elements confined by limited transverse reinforcement. These specimens were initially subjected to axial compression loading and cyclic lateral loading to failure, and subsequently repaired and subjected to loading again. The test specimens include two low-rise walls of aspect ratio 1.125 and two medium-rise walls of aspect ratio 1.625. Results show that significant drift capacities were achieved from the strengthened walls. The performance of the repaired walls was similar to the original walls before repair in terms of the flexural behavior, shear strength, and ductility capacities. While the fiber-reinforced polymer (FRP) anchorage may undergo premature failure, it however failed only after the peak lateral strength of the repaired wall was attained. This paper demonstrates that repair of damaged RC walls using FRP is able to restore the performance of damaged RC walls while also serving as repair method of relative ease.     

Static Cyclic Response of Masonry Walls Retrofitted with Fiber-Reinforced Polymers

The behavior of seven one-half scale masonry specimens before and after retrofitting using fiber-reinforced polymer (FRP) is investigated. Four walls were built using one-half scale hollow clay masonry units and weak mortar to simulate walls built in central Europe in the mid-20th century. Three walls were first tested as unreinforced masonry walls; then, the seismically damaged specimens were retrofitted using FRPs. The fourth wall was directly upgraded after construction using FRP. Each specimen was retrofitted on the entire surface of a single side. All the specimens were tested under constant gravity load and incrementally increasing in-plane loading cycles. The tested specimens had two effective moment/shear ratio, namely, 0.5 and 0.7. The key parameter was the amount of FRP axial rigidity, which is defined as the amount of FRP reinforcement ratio times its E modulus. The single-side retrofitting/upgrading significantly improved the lateral strength, stiffness, and energy dissipation of the test specimens. The increase in the lateral strength was proportional to the amount of FRP axial rigidity. However, using high amount of FRP axial rigidity led to very brittle failure. Finally, simple existing analytical models estimated the ultimate lateral strengths of the test specimens reasonably well.     

FRP-Retrofitted URM Walls under In-Plane Shear: Review and Assessment of Available Models

In the last two decades, several seismic retrofitting techniques for masonry structures have been developed and practiced and fiber-reinforced polymer (FRP) material has been increasingly used owing to its high strength/stiffness to mass ratio and easy application. Although much research has been carried out on FRP strengthening of unreinforced masonry (URM) structures, most of it has been experimental studies to investigate the effectiveness of retrofitting techniques rather than the development of a rational design model. In addition, more research has been conducted on FRP-retrofitted URM walls under out-of-plane loads where flexural behavior dominates, the research on the shear strength of FRP-retrofitted URM walls has been limited. This paper presents a review of research in this area. Existing retrofitting techniques are overviewed, followed by a detailed discussion of experimental results of failure modes as they are directly related to the design model. The available design models are then assessed based on a test database collected from the available literature. Limitations of each model are addressed.     

Behavior of Composite Unreinforced Masonry–Fiber-Reinforced Polymer Wall Assemblages Under In-Plane Loading

An experimental investigation was conducted to study the in-plane behavior of face shell mortar bedded unreinforced masonry (URM) wall assemblages retrofitted with fiber-reinforced polymer (FRP) laminates. Forty-two URM assemblages were tested under different stress conditions present in masonry shear and infill walls. Tests included prisms loaded in compression with different bed joint orientation (on/off-axis compression), diagonal tension specimens, and specimens loaded under joint shear. The behavior of each specimen type is discussed with emphasis on modes of failure, strength and deformation characteristics. Results showed that the application of FRP laminates on URM has a great influence on strength, postpeak behavior, as well as altering failure modes and maintaining the specimen integrity. The retrofitted specimens reached compressive strength of 1.62–5.64 times that of their unretrofitted counterparts, depending on the bed joint orientation, and joint shear strength increased by eightfold.     

Tensile Behavior of FRP Anchors in Concrete

Strengthening of concrete structures using fiber-reinforced polymer (FRP) systems has become a widely accepted technology in the construction industry over the past decade. Externally bonded FRP sheets are proven to be a feasible alternative to traditional methods for strengthening and stiffening deficient reinforced or prestressed concrete members. However, the delamination of FRP sheets from the concrete surface poses major concerns, as it usually leads to a brittle member failure. This paper reports on the development of FRP anchors to overcome delamination problems encountered in surface bonded FRP sheets. An experimental investigation was conducted on the performance of carbon FRP anchors that were embedded in normal- and high-strength concrete test specimens. A total of 81 anchors were tested under monotonic uniaxial loading. Test parameters included the length, diameter, and angle of inclination of the anchors and the compressive strength of the concrete. The experimental results indicate that FRP anchors can be designed to achieve high pullout capacities and hence can be used effectively to prevent or delay the delamination of externally bonded FRP sheets. The results also indicate that the diameter, length, and the angle of inclination of the anchors have a significant influence on the pullout capacity of FRP anchors.     

Numerical Modeling of FRP Shear-Strengthened Reinforced Concrete Beams

An attractive technique for the shear strengthening of reinforced concrete beams is to provide additional web reinforcement in the form of externally bonded fiber-reinforced polymer (FRP) sheets. So far, theoretical studies concerning the FRP shear strengthening of reinforced concrete members have been rather limited. Moreover, the numerical analyses presented to date have not effectively simulated the interfacial behavior between the bonded FRP and concrete. The analysis presented here aims to capture the three-dimensional and nonlinear behavior of the concrete, as well as accurately model the bond–slip interfacial behavior. The finite-element model is applied to various strengthening strategies; namely, beams with vertical and inclined side-bonded FRP sheets, U-wrap FRP strengthening configurations, as well as anchored FRP sheets. The proposed numerical analysis is validated against published experimental results. Comparisons between the numerical predictions and test results show excellent agreement. The finite-element model is also shown to be a valuable tool for gaining insight into phenomena (e.g., slip profiles, debonding trends, strain distributions) that are difficult to investigate in laboratory tests.     

Monte Carlo Simulation of Shear Capacity of URM Walls Retrofitted by Polyurea Reinforced GFRP Grids

A model proposed in the literature for the evaluation of the in-plane shear capacity of unstrengthened and strengthened concrete and clay brick unreinforced masonry (URM) walls was modified and calibrated following the results from an experimental research program. The tested walls were strengthened with grids made from glass fiber-reinforced polymer (GFRP) embedded within a rapid-setting sprayed polyurea. Various GFRP grid reinforced polyurea layouts were investigated, and consisted of strips oriented in either the vertical or horizontal direction and installed on one or both faces. The prediction models proposed in this paper were subsequently evaluated using a probabilistic Monte Carlo simulation (MCS) by considering the uncertainty and variability of the independent variables, which were assumed to follow a truncated normal distribution. Corroborated by the MCS, test results clearly show that the failure modes of the strengthened URM walls were affected by the strengthening scheme. Experimental and simulation results are presented and discussed in this paper.     

Nonlinear Behavior of a Masonry Subassemblage Before and After Strengthening with Inorganic Matrix-Grid Composites

Past experimental tests on a full-scale masonry wall with an opening evidenced the key role of the spandrel panel in the in-plane nonlinear response of the system. Recent seismic codes do not provide specific criteria to assess and to strengthen existing masonry spandrel panels with inorganic matrix-grid (IMG) composites. Numerical finite-element (FE) analyses are used to deepen the knowledge about the nonlinear response of masonry walls and the role of the IMG strengthening system. The comparison of experimental and numerical results contributes to the development of a simplified analytical model to assess the influence of the external reinforcement system on the in-plane seismic response of masonry wall systems. Some hints about the strengthening design that could change the failure mode from brittle shear to ductile flexure are given. Finally, a further enhancement of the IMG strengthening system is proposed to avoid the undesirable splitting phenomena attributable to compression forces and to exploit the full compressive strength of masonry against bending moments.     

Numerical Analysis of FRP-Composite-Strengthened RC Panels with Anchorages against Blast Loads

Extensive research has been conducted to investigate the blast effects on building structures and the protective design methods using the fiber-reinforced polymer (FRP) strengthening concepts in resisting structural damage and preventing injuries against dynamic explosive impacts. Both numerical and experimental studies have proved the effectiveness of FRP in strengthening structures to resist blast loads. However, problems related to end anchorage, bond length, and premature peeling have been concerns when strengthening structures in flexure or shear using FRP. In this paper, numerical analyses of FRP-composite-strengthened RC walls with or without additional anchors are carried out to examine the structural response under blast loads. The results illustrated that an anchor system is often necessary when using external FRP laminates for strengthening RC walls to prevent premature peeling. This study presents three simulations of RC walls, namely, an unstrengthened RC wall, an FRP-composite-strengthened RC wall with end anchorage, and an FRP-composite-strengthened RC wall with both end anchorage and anchors applied at a minimum spacing across the width and height of the RC wall. Commercial software LS-DYNA is used to carry out the structural response analysis. Numerical results show that anchorage of the FRP sheet may prevent peeling damage and therefore enhances the capacity of the FRP-strengthened RC walls against blast loads. However, anchors result in stress concentration and may cause FRP rupture.     

Durability of GFRP Bars’ Bond to Concrete under Different Loading and Environmental Conditions

In the last decade, noncorrodible fiber-reinforced polymer (FRP) reinforcing bars have been increasingly used as the main reinforcement for concrete structures in harsh environments. Also, owing to their lower cost compared with other types of FRP bars, glass-FRP (GFRP) bars are more attractive to the construction industry, especially for implementation in bridge deck slabs. In North America, bridge deck slabs are exposed to severe environmental conditions, such as freeze-thaw action, in addition to traffic fatigue loads. Although the bond strength of GFRP bars has been proved to be satisfactory, their durability performance under the dual effects of fatigue-type loading and freeze-thaw action is still not well understood. Few experimental test data are available on the bond characteristics of FRP bars in concrete elements under different loading and environmental conditions. This research investigates the individual and combined effects of freeze-thaw cycles along with sustained axial load and fatigue loading on the bond characteristics of GFRP bars embedded in concrete. An FRP-reinforced concrete specimen was developed to apply axial-tension fatigue or sustained loads to GFRP bars within a concrete environment. A total of thirty-six test specimens was constructed and tested. The test parameters included bar diameter, concrete cover thickness, loading scheme, and environmental conditioning. After conditioning, each specimen was sectioned into two halves for pullout testing. Test results showed that fatigue load cycles resulted in approximately 50% loss in the bond strength of sand-coated GFRP bars to concrete, while freeze-thaw cycles enhanced their bond to concrete by approximately 40%. Larger concrete covers were found more important in cases of larger bar sizes simultaneously subjected to fatigue load and freeze-thaw cycles.     

Seismic Behavior of RC Columns with Bond-Critical Regions: Criteria for Bond Strengthening Using External FRP Jackets

In 2003, an experimental research program was initiated at the American University of Beirut with the objectives of (1) evaluating the effectiveness of external fiber-reinforced polymer (FRP) confinement in improving the bond strength of spliced reinforcement in reinforced-concrete (RC) columns and its implications on the lateral load capacity and ductility of the columns under seismic loading; and (2) establishing rational design criteria for bond strengthening of spliced reinforcement using external FRP jackets. This paper presents a discussion of recent experimental results dealing with rectangular columns and the results of a pilot study conducted on circular columns with particular emphasis on aspects related to the bond strength of the spliced column reinforcement. A nonlinear analysis model is developed for predicting the envelope load–drift response, taking into account the effect of FRP confinement on the stress–strain behavior of concrete in compression. Results predicted by the model showed excellent agreement with the test results. Design expressions of the bond strength of spliced bars in FRP-confined concrete were assessed against the current experimental data, and a criterion for seismic FRP strengthening of bond-critical regions in RC members is proposed.     

Bond Strength of Tension Lap Splices in High-Strength Concrete Beams Strengthened with Glass Fiber Reinforced Polymer Wraps

This paper presents the experimental results of the first phase of a study undertaken at the American University of Beirut to examine the effectiveness of fiber reinforced polymer (FRP) wraps to confine steel reinforcement in a tension lap splice region anchored in high-strength reinforced-concrete beams. Seven beam specimens were constructed. The specimens were reinforced on the tension side with three deformed bars spliced at midspan. The splice region was devoid of any transverse reinforcement to allow a full examination of the FRP wrap contribution. Glass fiber reinforced polymer (GFRP) sheets were used. The main test variables were the GFRP configuration in the splice region (one strip, two strips, or a continuous strip), and the number of layers of the GFRP wraps placed around the splice region (one layer or two layers). All GFRP wraps were U-shaped. Except for the epoxy adhesive, no other anchorage mechanism or bonding procedure was applied for the GFRP wraps on the concrete beam. Following the application of the GFRP wraps, the beams were tested in positive bending. The test results demonstrated that GFRP wraps were effective in enhancing the bond strength and ductility of failure mode of the tension lap splices, especially when continuous strips were applied over the splice region.