Effects of Deposition Conditions and Counter Bodies on the Tribological Properties of Pulsed DC Magnetron Sputtered TiN–MoS<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript> Composite Coating

In the current study, TiN–MoS _x composite coatings were deposited by co-sputtering of MoS₂ and Ti targets under a mixture of Ar and N₂ gas environment using pulsed DC closed-field unbalanced magnetron sputtering. The tribological response of TiN–MoS _x composite coatings was studied against two different counter bodies: cemented carbide (WC–6% Co) ball and pin made of aluminium alloy (AlSiMg). First, the effect of substrate bias was studied on tribological properties using cemented carbide ball. Lowest coefficient of friction in the range of 0.03–0.04 was obtained for the specimen deposited at a substrate bias of −60 V. Wear coefficient was also found to be minimum for the same specimen. Coatings were further deposited at an optimum bias of −60 V in order to vary MoS _x content of TiN–MoS _x composite coating. Effect of variation of chemical composition of the coating was then studied on tribological performance of the coating against aluminium alloy counterface. Excellent anti-sticking property of MoS _x was found to have enabled the TiN–MoS _x composite coating to achieve considerably low coefficient of friction against aluminium alloy. It was shown that with optimum MoS _x content of TiN–MoS _x composite coating, it was possible to attain as low coefficient of friction as 0.09 against aluminium alloy even under normal atmospheric condition.     

Tribological behaviour and wear mechanism of MoS2–Cr coatings sliding against various counterbody

MoS₂–Cr coatings with different Cr contents have been deposited on high speed steel substrates by closed field unbalanced magnetron (CFUBM) sputtering. The tribological properties of the coatings have been tested against different counterbodies under dry conditions using an oscillating friction and wear tester. The coating microstructures, mechanical properties and wear resistance vary according to the Cr metal-content. MoS₂ tribological properties are improved with a Cr metal dopant in the MoS₂ matrix. The optimum Cr content varies with different counterbodies. Showing especially good tribological properties were MoS₂–Cr8% coating sliding against either AISI 1045 steel or AA 6061 aluminum alloy, and MoS₂–Cr5% coating sliding against bronze. Enhanced tribological behavior included low wear depth on coating, low wear width on counterbody, low friction coefficients and long durability.     

Friction and endurance of MoS2/ta-C coatings produced by Laser Arc deposition

The tribological behaviour of MoS₂/ta-C double layer coatings deposited by Laser-Arc technology was investigated in vacuum and air. In vacuum environment, the friction coefficient against steel balls varies between 0.005 and 0.02 depending on the contact pressure. At high contact pressures, the friction coefficient is as low as 0.005 and the life time between 340,000 and 500,000 cycles. Furthermore, it is shown that a ta-C base layer improves the performance of MoS₂ coating.Surface analyses were performed before and after the tribological tests by means of SEM, EDX, XRD, and TEM. They show that in the top layer beneath the sliding surface crystallization of the initially quasi-amorphous MoS₂ took place. TEM images also verified an orientation of the basal MoS₂-lattice planes parallel to the surface.     

Effect of Atmosphere and Temperature on the Tribological Behavior of the Ti Containing MoS<Subscript>2</Subscript> Coatings Against Aluminum

MoS₂ coatings exhibit low coefficient of friction (COF) when sliding against aluminum; however, the magnitudes of their COF show high sensitivity to environmental conditions. Ti could reduce the sensitivity of the frictional behavior of MoS₂ coatings to moisture. This study examines the tribological properties of Ti containing MoS₂ coating (Ti–MoS₂) tested against an aluminum alloy (Al-6.5% Si) in ambient air (58% relative humidity, RH), dry oxygen, dry air and dry N₂ (< 4% RH) atmospheres. The Ti–MoS₂ coating exhibited similar COF values under an ambient (0.14), dry oxygen (0.15) and dry air (0.16) atmospheres. It was found that oxidation of MoS₂ to MoO₃ was responsible for high COF under these testing conditions as revealed by Energy-dispersive X-ray Spectroscopy (EDS) and micro-Raman spectroscopy. However, a low and stable COF of 0.07 was observed under a dry N₂ condition. This work further showed that the tests performed at elevated temperatures, up to 400 °C in a dry N₂ atmosphere sustained the low and stable COF of the Ti–MoS₂ coatings. The sliding tests performed under a dry N₂ atmosphere prevented the formation of MoO₃ and as a result, the Ti–MoS₂ coatings maintained low COF values. Low COF values were also attributed to the formation of MoS₂ transfer layers.     

Influence of low friction coatings on the scuffing load capacity and efficiency of gears

The influence of multilayer composite surface coatings on gear scuffing load carrying capacity, gear friction coefficient and gearbox efficiency is discussed in this work.The deposition procedures of molybdenum disulphide/titanium (MoS₂/Ti) and carbon/chromium (C/Cr) composite coatings are described.Tests reported in the literature, such as Rockwell indentations, ball cratering, pin-on-disc and reciprocating wear, confirm the excellent adhesion to the substrate and the tribological performance of these coatings, suggesting they can be applied with success in heavy loaded rolling–sliding contacts, such as those found in gears.FZG gear scuffing tests were performed in order to evaluate the coatings anti-scuffing performance, which both improved very significantly in comparison to uncoated gears. These results in conjunction with the friction power intensity (FPI) scuffing criterion allowed the determination of a friction coefficient factor X_SC to include the coating influence on the friction coefficient expression.The composite coatings were also applied to the gears of a transfer gearbox and its efficiency was measured and compared at different input speeds and torques with the uncoated carburized steel gears. Significant efficiency improvement was found with the MoS₂/Ti coating.     

Tribological properties of selected PVD coatings when slid against ductile materials

In this paper, a physical vapour deposited (PVD) deposited TiB₂ coating is compared in dry sliding with commercial PVD titanium nitride (TiN), titanium aluminium nitride (TiAlN) and titanium carbonitirde (TiCN) as to frictional properties and tendency of counter material pick-up. The aim is to investigate if the superior behaviour of the TiB₂ coating experienced in severe sliding applications against aluminium alloys can be extended to other materials with a similarly poor tribological characteristics.A new tribological test for sliding contact has been used. The test configuration involves two crossed elongated cylindrical test specimens which are forced to slide axially against each other at a constant sliding speed and a gradually increasing normal load, while recording the friction. The evaluation is performed by correlating the friction history with the width, topography and composition of the sliding tracks as detected by optical and scanning electron microscopy.Coated cemented carbide (CC) test cylinders have been slid against cylinders of a Ti alloy (Ti–6Al–4V), an Al alloy (Al 7075) and Inconel 718. It was shown that the TiB₂ surface displayed superior friction and anti-sticking properties, when tested against the aluminium alloy. Against the Ti and Inconel alloys no major difference between the coatings could be found. Instead, it is concluded that the friction coefficient is determined by the plastic properties of the counter material since a complete transfer layer instantly builds up on the coating.It proved possible to estimate the friction force from the width of the sliding tracks, the Vickers hardness of the counter material and simple plastic considerations. This estimation also verifies the unexpectedly low friction of all coatings against the Ti alloy.     

Effect of MoS2-based composite coatings on tribological behavior and efficiency of gear

MoS₂-based Ti composite coatings were deposited on the SCM420 alloy and gears using an RF magnetron sputtering (RFMS) system. While MoS₂ coating had been coated on the silicon substrate. The coatings structures were compared to each other to find the effect of Ti. The composite coatings have been tested in a ball-on-disk tribometer to investigate tribological behavior at various conditions. The scratch test was conducted to characterize adhesion force between composite coatings and substrates. The structure of the coatings has been extensively studied by a variety of techniques, including optical microscopy, X-ray diffraction (XRD) and scanning electron microscopy (SEM), etc. The composite coatings were also applied to the gears of a reduction gearbox. The efficiency of uncoated and MoS₂-based Ti coated gear was measured and compared at various input rotating speed under absorption oil film condition. It was found that the efficiency of gear had significantly improved after MoS₂-based Ti composite coatings deposition.     

Deposition of duplex Al2O3/TiN coatings on aluminum alloys for tribological applications using a combined microplasma oxidation (MPO) and arc ion plating (AIP)

Microplasma oxidation (MPO) has recently been studied as a cost-effective plasma electrolytic process to provide thick and hard ceramic coatings with excellent surface load-bearing capacity on aluminum alloys. However, for sliding wear applications, such ceramic coatings often exhibit relatively high friction coefficients against many counterface materials. Although coatings deposited by physical vapour deposition (PVD) techniques such as TiN coatings are well known for providing surfaces with a high hardness, in practice they often exhibit poor performance under mechanical loading, since the coatings are usually too thin to protect the substrate from the contact conditions. In this paper, these challenges were overcome by a duplex process of microplasma oxidation and arc ion plating (AIP), in which an alumina layer Al₂O₃ was deposited on an Al alloy substrate (using MPO as a pre-treatment process) for load support, and a TiN hard coatings were deposited (using AIP) on top of the Al₂O₃ layer for low friction coefficient. Microhardness measurements, pin-on-disc sliding wear tests, and antiwear tests using a Timken tester were performed to evaluate the mechanical and tribological properties. Scanning electron microscopy (SEM) was used to observe coating morphology, and to examine wear scars from pin-on-disc test. The research demonstrates that a hard and uniform TiN coating, with good adhesion and a low coefficient of friction, can successfully be deposited on top of an alumina intermediate layer to provide excellent load support. The investigations indicate that a duplex combination of MPO coating and TiN PVD coating represents a promising technique for surface modification of Al alloys for heavy surface load bearing application.     

Influence of Parameters of Reactive Magnetron Sputtering on Tribomechanical Properties of Protective Nanostructured Ti–Al–N Coatings

The influence of substrate temperature and bias voltage on the structure and tribomechanical properties of the Ti–Al–N coatings obtained by reactive magnetron sputtering technique has been investigated. The structure and elemental and phase compositions have been studied by scanning electron microscopy, Rutherford backscattering, and X-Ray diffraction. The results of friction and wear experiments indicated that the lowest coefficient of friction (three times lower than 12Cr18Ni10Ti) corresponded to a coating deposited at a bias voltage of–200 V and a substrate temperature of 340°С, while the most wear-resistant coating (under a load of 700 mN and the testing time of 1080 s) was Ti–Al–N sputtered at a bias voltage of–200 V and a substrate temperature of 440°С.     

Investigation of antiwear coatings deposited by the pvd process

The tribological properties of various PVD‐deposited coatings (vacuum arc method) have been tested, both single‐layer coatings (TiN, CrN, Ti(C,N), and Cr(C,N)) and multilayer coatings (Cr(C,N)/CrN/Cr and CR(C,N)/(CrN+Cr₂N)/CrN/Cr). An unlubricated ball‐on‐disc tribosystem was used in which an Al₂O₃ ball is pressed against a coated steel disc rotating in the horizontal plane. A novelty of the method is the removal of wear debris from the contact zone using a draught of dry argon. This improves the repeatability of the test results and the stability of the tribological characteristics. It is shown that CrN coatings exhibit the best antiwear properties and Ti(C,N) the worst. Multilayer coatings have better antiwear properties than single‐layer ones. The friction coefficients for CrN and Cr(C,N) coatings are much smaller than for the commonly used TiN. A correlation has also been found between the physical properties of the coatings tested (adhesion of the coating to the substrate assessed in scratch tests, and coating hardness) and their antiwear properties. An improvement in coating‐substrate adhesion results in wear reduction, while greater hardness (causing a coating embrittlement increase and a change in the wear mechanism) brings about greater wear. There is no correlation between the physical properties and the friction coefficients of the coatings tested.     

Wear-Resistant Coatings with Engineered Structure by Laser Cladding

Several types of wear-resistant and/or low-friction coefficient coatings with engineered structure (e.g., metal matrix composites, MMC) have been produced by coaxial laser cladding. The MoS₂ graded layer is created after thermal diffusion synthesis on the surface of a previously deposited molybdenum coating. MMC coatings with identical composition and different microstructure show different tribological behavior.     

Wear resistant multilayer nanocomposite WC1−x/C coating on Ti–6Al–4V titanium alloy

A significant improvement of tribological properties on Ti–6Al–4V has been achieved by developed in this study multilayer treatment method for the titanium alloys. This treatment consists of an intermediate 2 μm thick TiC_xN_y layer which has been deposited by the reactive arc evaporation onto a diffusion hardened material with interstitial O or N atoms by glow discharge plasma in the atmosphere of Ar+O₂ or Ar+N₂. Subsequently, an external 0.3 μm thin nanocomposite carbon-based WC_1−x/C coating has been deposited by a reactive magnetron sputtering of graphite and tungsten targets. The morphology, microstructure, chemical and phase compositions of the substrate material after treatment and coating deposition have been investigated with use of AFM, SEM, EDX, XRD, 3D profilometry and followed by tribological investigation of wear and friction analysis. An increase of hardness in the diffusion treated near-surface zone of the Ti–6Al–4V substrate has been achieved. In addition, a good adhesion between the intermediate gradient TiC_xN_y coating and the Ti–6Al–4V substrate as well as with the external nanocomposite coating has been obtained. Significant increase in wear resistance of up to 94% when compared to uncoated Ti–6Al–4V was reported. The proposed multilayer system deposited on the Ti–6Al–4V substrate is a promising method to significantly increase wear resistance of titanium alloys.     

Molybdenum disulphide/titanium low friction coating for gears application

Multi-layer composite surface coatings made of MoS₂/titanium, exhibit good mechanical and tribological properties in several industrial applications. Its applicability to industrial gears is discussed in this work.Several tests, like Rockwell indentations, ball cratering, pin-on-disc and reciprocating wear tests, were performed in order to evaluate the adhesion to the substrate and the tribological performance of this coating.Twin-disc tests, performed at high-contact pressure and high-slide-to-roll ratios, confirmed the good adhesive and tribological properties of the MoS₂/titanium coating and left good indications about the applicability of the MoS₂/titanium coating to gears.Scuffing gear tests were performed in the FZG machine in order to evaluate the anti-scuffing performance of this coating. Finally, the MoS₂/titanium coating was applied to the gearing in a gearbox and its influence on the gearbox efficiency was studied.     

Effect of deposition pressure on microstructure and tribological behavior of MoS<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>/MoS<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>-Mo nanoscale multi-layer films

MoS _x /MoS _x -Mo multi-layer films consisted of several bilayers and a surface layer on steel substrate were deposited by d.c. magnetron sputtering at different deposition pressures. Each bilayer contained a MoS _x layer with 80 nm in thickness and a MoS _x -Mo composite layer with 20 nm in thickness. With the increase of deposition pressure, the perpendicular orientation of the basal plane prevailed while the parallel orientation decreased. The tribological properties of the multi-layer films were investigated by using a ball-on-disk tribometer both in vacuum and in humid air. The multi-layer film deposited at 0.24 Pa had a compact, consistent layered structure with high intensity of (002) plane and low S content compared to the others deposited at 0.32 and 0.40 Pa, and showed the lowest friction coefficient and wear rate in humid air.     

Characterisation of ZrO2 layers deposited on Al2O3 coating

The paper describes a method of coating combining two different layer types. The first layer is Al₂O₃ produced by plasma spraying with a thickness of around 200 μm which was deposited on a stainless steel substrate. Subsequently, ZrO₂ layers were deposited on to the Al₂O₃ coating by a sol–gel process using a dip coating technique. The dip coating process was repeated in order to see the influence of the number of ZrO₂ layers. Moreover, the effect of annealing temperature was investigated. In order to study their tribological behaviour, the coatings were subjected to micro-scale abrasion, scratch testing and ball-on-disc tests. The result shows that sol–gel ZrO₂ top layers reduce friction and enhance the wear resistance of the coating system.     

MoS2‐based alloys and nanocomposites for solid lubrication

The development of MoS₂ coatings has involved the modification of substrate surfaces, the addition of metals or compounds to the MoS₂, and variation in the deposition process parameters affecting the properties of deposited films. More recently, multilayer and periodic nanolayer coating structures have also been investigated. At present, work is concentrated on alloys of MoS₂, mainly with various metals, and targeted at terrestrial (ambient air) applications. The addition of metals or compounds to physical‐vapour‐deposited MoS₂ has led to improvements in coating performance, for example, greater stability of friction coefficient, greater film endurance, and increased temperature/oxidation resistance. The metal or compound can be either in the form of nanoscale multilayers or mixed with the MoS₂, sometimes leading to nanoclusters within a MoS₂ matrix. Microstructural analysis seems to show that the primary function of these additives is to suppress the formation of low‐density, columnar structures. At certain concentrations an added metal can also enhance the formation of the tribologically favourable (002) orientation of the MoS₂ crystallites. Other changes in the properties of MoS₂—metal composites may be due to their oxidation resistance, as indicated by the stability of these films against storage in air and their increased endurance when in sliding contacts at elevated temperatures.     

Tribological characteristics of nanocomposite vacuum-plasma Ti-Hf, Ti-Hf-N, and Ti-Hf-Si-N coatings

The tribological characteristics of nanocomposite Ti-Hf, Ti-Hf-N, and Ti-Hf-Si-N coatings deposited by the pulse HF-assisted vacuum arc method are studied. A substantial increase in the wear resistance and a decrease in the coefficient of friction of a protective Ti-Hf-Si-N coating compared to the steel substrate and protective Ti-Hf and (Ti, Hf)N coatings are found and explained.     

Corrosion and wear behaviour of ZrN thin films

Abstract

ZrN coating is an alternative candidate to replace the conventional TiN coating especially for high temperature oxidation resistance applications. ZrN coatings of varying thickness (1·5, 2·0, 2·5, 3·0 and 4·0 μm) were deposited on 316 stainless steel substrates by cathodic arc evaporation in a reactive nitrogen atmosphere. The influences of lamellae thickness on the microstructure, tribological and corrosive properties of the films were investigated. The coefficient of steady state friction of the films ranged from 0·213 to 0·659. The corrosion resistance of the coatings was tested in 1 N H₂SO₄ solution. The results indicate that the microstructure, wear and corrosion properties of the films were dependent on lamellae thicknesses and film structure.     

Effect of current density,MoS2 content and bath agitation on tribological properties of electrodeposited nanostructured Ni-MoS2 composite coatings

ABSTRACT

Nanostructured nickel coatings with molybdenum disulphide particles were electrodeposited to form composite coatings. Three different current densities, i.e. 3, 5 and 7?A/dm² were investigated initially. The best results were obtained with 5 A/dm² for codeposition of nanostructured Ni-MoS₂ composite coatings. With the addition of 1–4?g/L molybdenum disulphide to the bath, the weight percentages of MoS₂ particles in the coatings were 23–38%. This increase of MoS₂ content was accompanied with decrease in friction coefficient of the coatings from 0.35 to 0.08. Wear resistance of the coatings was increased with increasing MoS₂ content and the weight loss was decreased from 1.4 to 0.7?mg. Hardness was decreased from 585 to 400 VHN with increasing the MoS₂ content. By increasing bath agitation speed up to 150?rpm, more MoS₂ particles were embedded in the matrix and the coatings showed better wear resistance. However, increase of agitation speed from 150 to 200?rpm caused a decrease of MoS₂ particles in the nickel matrix due to the turbulent motion of particles in the bath. Overall, it was shown that the lubricating effect of MoS₂ in the coating was more influential than the nanocrystallinity of the nickel matrix in improving tribological properties of these composite coatings.     

Tribological Properties of Reactive Magnetron Sputtered V2O5 and VN–V2O5 Coatings

Next generation of advanced hard coatings for tribological applications should combine the advantages of hard wear resistant coatings with low-friction films. In this study, the tribological behaviour of vanadium pentoxide (V₂O₅) single-layer as well as VN–V₂O₅ bi-layer coatings was investigated in the temperature ranging between 25 and 600 °C. For VN–V₂O₅ bi-layer coatings, the V₂O₅ top-layers were deposited by dc and bipolar-pulsed dc reactive magnetron sputtering, where the V₂O₅ phase shows preferred growth orientation in (200) and (110), respectively. The V₂O₅ single-layer coatings were prepared by dc reactive magnetron sputtering with a substrate bias of −80 V which leads to a preferred (200) growth orientation. Tribological properties were evaluated using a ball-on-disc configuration in ambient air with alumina balls as counterpart. The structure of the as-deposited films and eventual changes after tribometer testing were identified using X-ray diffraction, Raman spectroscopy and scanning electron microscopy. The friction coefficient of VN–V₂O₅ bi-layer coatings deposited in dc and pulsed dc mode decreases from room temperature to 600 °C, where the pulsed dc VN–V₂O₅ coatings have a significantly lower coefficient of friction over the whole testing temperatures reaching a value of 0.28 at 600 °C. Up to 400 °C, V₂O₅ single-layer coatings showed almost the same coefficient of friction as pulsed dc VN–V₂O₅ bi-layer coatings but reached a value of 0.15 at 600 °C. It seems that thermal activation of crystallographic slip systems is necessary for V₂O₅ films to show a low-friction effect.