Investigation into sliding wear performance of zinc-based alloy reinforced with SiC particles in dry and lubricated conditions

The objective of the present investigation was to assess the influence of SiC particle dispersion in the alloy matrix, applied load, and the presence of oil and oil plus graphite lubricants on the wear behaviour of a zinc-based alloy. Sliding wear performance of the zinc-based alloy and its composite containing SiC particles has been investigated in dry and lubricated conditions. Base oil or mixtures of the base oil with different percentages of graphite were used for creating the lubricated conditions. Results show a large improvement in wear resistance of the zinc-based alloy after reinforcement with SiC particles. The lubrication improved the wear resistance and friction behaviour of both the reinforced and base alloys. It was also observed that there exists an optimum concentration of graphite particles in the lubricant mixture that leads to the best wear performance. The composite experienced higher frictional heating and friction coefficient than the matrix alloy in all the cases except oil lubricated conditions; a mixed trend was noticed in the latter case. The wear rate and frictional heating increased with load while friction coefficient was affected in an opposite manner. Test duration influenced the frictional heating and friction coefficient of the samples in a mixed manner.Examination of worn surfaces revealed a change of predominating wear mechanisms from severe ploughing and/or abrasive wear for base alloy to delamination wear for the reinforced material under dry sliding conditions. The presence of the lubricant increased the contribution of adhesive wear component while reducing the severity of abrasion. This was attributed to the generation of more stable lubricant films on the contacting surfaces. Cross-sections of worn surfaces indicated substantial wear-induced plastic deformation, thereby suggesting adhesive wear to be a predominant wear mechanism in this study. The debris particles revealed deformed flakes and machining chips signifying the involvement of adhesion and abrasion modes of wear respectively.     

Tribological Behavior of Composites Based on ZA-27 Alloy Reinforced with Graphite Particles

The objective of this investigation is to assess the influence of graphite reinforcement on tribological behavior of ZA-27 alloy. The composite with 2 wt% of graphite particles was produced by the compocasting procedure. Tribological properties of unreinforced alloy and composite were studied, using block-on-disk tribometer, under dry and lubricated sliding conditions at different specific loads and sliding speeds. The worn surfaces of the samples were examined by the scanning electron microscopy (SEM). The obtained results revealed that ZA-27/graphite composite specimens exhibited significantly lower wear rate and coefficient of friction than the matrix alloy specimens in all the combinations of applied loads (F _n ) and sliding speeds (v) in dry and lubricated tests. The positive tribological effects of graphite reinforcement of ZA-27 in dry sliding tests were provided by the tribo-induced graphite film on the contact surface of composite. In test conditions, characterized by the small graphite content and modest sliding speeds and applied loads, nonuniform tribo-induced graphite films were formed leading to the increase of the friction coefficient and wear rate, with increase of the sliding speed and applied load. In conditions of lubricated sliding, the very fine graphite particles formed in the contact interface mix with the lubricating oil forming the emulsion with improved tribological characteristics. Smeared graphite decreased the negative influence of F _n on tribological response of composites, what is manifested by the mild regime of the boundary lubrication, as well as by realization of the mixed lubrication at lower values of the v/F _n ratio, with respect to the matrix alloy.     

Tribological Behavior of Ti3Al2.5V Alloy Sliding against EN-31 Steel under Dry Condition

This article aims to study the friction and wear behavior of Ti3Al2.5V alloy sliding against EN-31 steel under dry condition using a multi-tribotester. The effect of variation in load and sliding velocity on wear rate, average coefficient of friction, and contact temperature has been studied and analysis of wear debris has been carried out. Scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS) were employed to study the morphology of the wear tracks and deduce microchemical information at the elemental level of worn samples, respectively. Results reveal that the wear rate of Ti-3Al-2.5V increases with increasing sliding velocity and increasing normal load with few exceptions. The average coefficient of friction decreases as the normal load increases with exceptions at some loads. SEM micrographs of worn samples obtained at different loads and sliding velocities show the formation of wear tracks on the surface due to ploughing and flaking of the matrix. The main mechanism responsible for wear of Ti3Al2.5V alloy sample is rupture of the matrix and abrasion. Wear debris analysis shows irregular-shaped wear particles with very sharp edges that appeared to be plastically deformed at high sliding velocity, whereas the wear debris is very loose and fine at lowest sliding velocity.     

Friction and wear behavior of Ni-P coated Si3N4 reinforced Al6061 composites

Al6061 matrix composite reinforced with nickel coated silicon nitride particles were manufactured by liquid metallurgy route. Microstructure and tribological properties of both matrix alloy and developed composites have been evaluated. Dry sliding friction and wear tests were carried out using pin on disk type machine over a load range of 20-100 N and sliding velocities of range 0.31-1.57 m/s. Results revealed that, nickel coated silicon nitride particles are uniformly distributed through out the matrix alloy. Al6061-Ni-P-Si₃N₄ composite exhibited lower coefficient of friction and wear rate compared to matrix alloy. The coefficient of friction of both matrix alloy and developed composite decreased with increase in load up to 80 N. Beyond this, with further increase in the load, the coefficient of friction increased slightly. However, with increase in sliding velocity coefficient of friction of both matrix alloy and developed composite increases continuously. Wear rates of both matrix alloy and developed composites increased with increase in both load and sliding velocity. Worn surfaces and wear debris was examined using scanning electron microscopy (SEM) for possible wear mechanisms. Energy dispersive spectroscope (EDS), X-ray diffraction (XRD) and X-ray photoelectron spectroscope (XPS) techniques were used to identify the oxides formed on the worn surfaces and wear debris.     

Friction and wear properties of bronze–graphite composite under water lubrication

Bronze–graphite composite was prepared using powder metallurgy. The friction and wear behaviors of the resulting composites in dry- and water-lubricated sliding against a stainless steel were comparatively investigated on an MM-200 friction and wear tester in a ring-on-block contact configuration. The wear mechanisms of the bronze–graphite composite were discussed based on examination of the worn surface morphologies of both the composite block and the stainless steel ring by means of scanning electron microscopy equipped with an energy dispersion spectrometry and on determination of some typical elements on the worn surfaces by means of X-ray photoelectron spectroscopy. It was found that the friction coefficient was higher under water lubrication than that under dry sliding and it showed margined change with increasing load under the both sliding conditions. A considerably decreased wear rate of the bronze–graphite composite was registered under water-lubricated sliding than under dry sliding, though it rose significantly at a relatively higher load. This was attributed to the hindered transfer of the composite onto the counterpart steel surface under water-lubricated sliding and the cooling effect of the water as a lubricant, while its stronger transfer onto the steel surface accounted for its higher wear rate under dry sliding. Thus, the bronze–graphite composite with much better wear-resistance under water-lubricated sliding than under dry sliding against the stainless steel could be a potential candidate as the tribo-material in aqueous environment.     

Influence of Thermal Fatigue on the Wear Behavior of Brake Discs Sliding against Organic and Semimetallic Friction Materials

ABSTRACT

In this article, brake discs are exposed to high thermal stress, causing thermal fatigue damage. The aim of this work is to study the evolution of the wear behavior of brake disc materials, such as cast iron, chromium steel, and metal matrix composites, under the influence of thermal fatigue. The brake disc specimens are heated and then cooled rapidly. Then, wear tests are carried out using a pin-on-disc-type tribometer. Organic and semimetallic friction materials are used for all wear tests. The results show that thermal fatigue affects the structure of the contact surfaces of all of the disc specimens by increasing their roughness. Furthermore, the wear rate of the friction materials increased, except a reduction of the wear rate is noted for the semimetallic friction material rubbing against cast iron. Moreover, thermal fatigue has no significant influence on the coefficient of friction. The worn surface of the metal matrix composite sliding against semimetallic friction material is characterized by abrasive and adhesive wear mechanisms.     

颗粒增强铝基复合材料干摩擦磨损特性研究

采用自制的干摩擦磨损试验机研究了3种ZL101-SiCp、Al2O3p复合材料及对比材料与半金属摩擦材料配副的摩擦磨损性能.结果表明,随接触压力的增加,材料的磨损率增加;随摩擦速度的增加,材料的磨损率减小.ZL101合金的磨损率比复合材料要大近3个数量级.复合材料的磨损率仅为HT250的1/3.随接触压力、速度的增加,材料的摩擦系数降低.复合材料的摩擦系数与HT250的相当,摩擦系数稳定性优于HT250.     

Tribological properties of flame sprayed Fe–Ni–RE alloy coatings under reciprocating sliding

Fe–Ni–RE self-fluxing alloy powders were flame sprayed onto 1045 carbon steel. The tribological properties of Fe–Ni–RE alloy coatings under dry sliding against SAE52100 steel at ambient conditions were studied on an Optimol SRV oscillating friction and wear tester in a ball-on-disc contact configuration. Effects of load and sliding speed on tribological properties of the Fe–Ni–RE coatings were investigated. The worn surfaces of the Fe–Ni–RE alloy coatings were examined with a scanning electron microscopy(SEM) and an energy-dispersive spectroscopy(EDS). It was found that the Fe–Ni–RE alloy coatings had better wear resistance than the SAE52100 steel. An adhered oxide debris layer was formed on the worn surface in friction. Area of the friction layer varied with variety of sliding speed, but did not vary with load. The oxide layer contributed to decreased wear, but increased friction. Wear rate of the material increased with the load, but dramatically decreased at first and then slightly decreased the sliding speed. The friction coefficient of the material was 0.40-0.58, and decreased slightly with the load, but increased with sliding speed at first, and then tended to be a constant value. Wear mechanism of the coatings was oxidation wear and a large amount of counterpart material was transferred to the coatings.     

Tribological Behavior of Micrometer- and Submicrometer-Size Cenosphere Particulate-Filled Glass Fiber–Reinforced Vinylester Composites Under Dry and Water-Lubricated Sliding Conditions

In this work, the tribological behavior of micrometer and submicrometer cenosphere particulate–filled E-glass fiber–reinforced vinylester composites have been investigated on a pin-on-disc tester under dry sliding and water-lubricated sliding conditions. Three different uniform sizes of cenosphere particles (2 μm, 900 nm, 400 nm) were used as fillers in the glass fiber–reinforced vinylester composites. The weight fraction of cenosphere particles has been varied in the ranges from 5, 10, 15, to 20 wt%. The experimental results show that all of the composites exhibited lower coefficient of friction and lower wear resistance under water-lubricated sliding conditions than under dry sliding. It has been noted that the submicrometer size (400 nm) cenosphere particulates as fillers contributed significantly to improve the wear resistance. It has also been noted that 10 wt% of the cenosphere particles is the most effective in reducing the wear rate and coefficient of friction. Effects of various wear parameters such as applied normal loads, sliding speeds, particle size, and particle content on the tribological behavior were also discussed. In order to understand the wear mechanism, the morphologies of the worn surface were analyzed by means of scanning electron microscopy (SEM) for composite specimens under both dry and water-lubricated sliding conditions.     

Dry sliding wear behaviour of cast high strength aluminium alloy (Al–Zn–Mg) and hard particle composites

This paper describes the results of dry sliding wear tests of aluminium alloy (Al–Zn–Mg) and aluminium (Al–Zn–Mg)–10, 15 and 25 wt.% SiCp composite was examined under varying applied pressure (0.2 to 2.0 MPa) at a fixed sliding speed of 3.35 m/s. The sliding wear behaviour was studied using pin-on-disc apparatus against EN32 steel counter surface, giving emphasis on the parameters such as coefficient of friction, rise in temperature, wear and seizure resistance as a function of sliding distance and applied pressure. It was observed that the wear rate of the alloy was noted to be significantly higher than that of the composite and is suppressed further due to addition of silicon carbide particles. The temperature rise near the contacting surfaces and the coefficient of friction followed reversed trend. Detailed studies of wear surfaces and subsurface deformation have been carried out. The wear mechanism was studied through worn surfaces and microscopic examination of the developed wear tracks. The wear mechanism strongly dictated by the formation and stability of oxide layer, mechanically mixed layer (MML) and subsurface deformation and cracking. The overall results indicate that the aluminium alloy–silicon carbide particle composite could be considered as an excellent material where high strength and wear resistance are of prime importance.     

Sliding wear behavior of planar random zinc-alloy matrix composites

The friction and wear behavior of planar random zinc-alloy matrix composites reinforced by discontinuous carbon fibres under dry sliding and lubricated sliding conditions has been investigated using a block-on-ring apparatus. The effects of fibre volume fractions and loads on the sliding wear resistance of the zinc-alloy matrix composites were studied. Experiments were performed within a load range of 50–300 N at a constant sliding velocity of 0.8 m s⁻¹. The composites with different volume fractions of carbon fibres (0–30%) were used as the block specimens, and a medium-carbon steel used as the ring specimen. Increasing the carbon fibre volume fraction significantly decreased the coefficient of friction and wear rates of both the composites and the medium-carbon steel under dry sliding conditions. Under lubricated sliding conditions, however, increasing the carbon fibre volume fraction substantially increased the coefficient of friction, and slightly increased the wear of the medium-carbon steel, while reducing the wear of the composite.Under dry sliding conditions, an increasing load increased not only the wear rates of both the composite and the unreinforced zinc alloy, but also those of their corresponding steel rings. However, the rate of increase of wear with increasing load for both the composite and its corresponding steel ring was much smaller than for the unreinforced zinc alloy and its corresponding steel ring. The coefficient of friction under dry sliding conditions appeared to be constant as load increased within a load range of 50–150 N for both the composite and the unreinforced zinc alloy, but increased at the higher loads. Under any load the coefficient of friction of the composite was lower than half that of the unreinforced zinc alloy under dry sliding conditions.     

铜碲硒铁合金的干摩擦磨损性能

利用环-盘式摩擦磨损试验机研究了铜碲硒铁合金的干摩擦磨损行为,分析了载荷和摩擦速度等参数对该合金摩擦磨损性能的影响,并用扫描电子显微镜对磨损形貌进行了观察.结果表明:铜碲硒铁合金的摩擦因数随载荷的增加变化不大,但随摩擦速度的增加而明显增大;合金的磨损率随载荷和摩擦速度的增加均增大;在轻载低速条件下,合金的磨损机制以犁削磨损和粘着磨损为主;在重载高速条件下,磨粒磨损和粘着磨损加剧.     

Application of grey-taguchi method for optimization of dry sliding wear properties of aluminum MMCs

Through a pin-on-disc type wear setup, the dry sliding wear behavior of SiC-reinforced aluminum composites produced using the molten metal mixing method was investigated in this paper. Dry sliding wear tests were carried on SiC-reinforced metal matrix composites (MMCs) and its matrix alloy sliding against a steel counter face. Different contact stresses, reinforcement percentages, sliding distances, and sliding velocities were selected as the control variables, and the responses were selected as the wear volume loss (WVL) and coefficient of friction (COF) to evaluate the dry sliding performance. An L25 orthogonal array was employed for the experimental design. Initially, the optimization of the dry sliding performance of the SiC-reinforced MMCs was performed using grey relational analysis (GRA). Based on the GRA, the optimum level parameters for overall grey relational grade in terms of WVL and COF were identified. Analysis of variance was performed to determine the effect of individual factors on the overall grey relational grade. The results indicated that the sliding velocity was the most effective factor among the control parameters on dry sliding wear, followed by the reinforcement percentage, sliding distance, and contact stress. Finally, the wear surface morphology and wear mechanism of the composites were investigated through scanning electron microscopy.     

聚酰亚胺复合材料与不同金属间干滑动时的摩擦学性能

采用MPX-2000型摩擦磨损试验机研究了聚四氟乙烯和二硫化钼填充聚酰亚胺复合材料在干滑动摩擦条件下与45钢、镍铬合金、铜和铝对磨时的摩擦磨损性能,并利用扫描电子显微镜和光学显微镜分析了复合材料及对偶件的磨损表面形貌。结果表明:复合材料与铝对磨时的摩擦因数和磨损率最低,分别约为与钢摩擦时的43%和49%;摩擦后铝表面形成均匀连续的转移膜,45钢、镍铬合金和铜的表面没有形成有效转移膜,因此复合材料的摩擦因数较大;复合材料与不同金属材料摩擦时的磨损机理主要是粘着磨损与疲劳磨损。     

磨料粒度对表面微织构纯钛干摩擦性能的影响

为了提高钛及钛合金钻具在超深钻探、深海钻探和外太空钻探工程中的减摩抗磨性能。利用激光表面加工技术在工业纯钛（TA2）表面制备了不同参数的点阵微织构。采用MS-T3000摩擦磨损试验机测试了微织构钛合金在不同粒度模拟月壤作用下的摩擦学性能。利用扫描电子显微镜和能谱分析仪分析磨痕形貌及元素含量。研究结果表明：当磨料粒度小于微织构点阵的直径时,磨料压入微织构点阵里,磨料具有滚动和滑动两种运动方式。当粒度大于微织构点阵的直径时,磨料不能完全压入微织构点阵里,磨料对微织构TA2表面产生了滑动犁削作用。由于两种磨料磨损的作用机理不同,同等条件下,小粒度的磨料作用下的微织构TA2的摩擦因数和磨损率较大粒度磨粒作用下的最大减少量分别为50%和53%。考虑磨料粒度与微结构的匹配性,可以大大降低摩擦减少磨损。     

Tribological behavior of microwave processed copper–nanographite composites

Excellent properties offered by nanographite particles are exploited as a reinforcement to the copper matrix. The effects of graphite particle size, spatial distribution, normal load and sliding speed on the friction and wear performance of microwave sintered copper metal matrix composites were studied using a pin-on-disc tribometer. Copper–nanographite composites show higher wear resistance and low coefficient of friction compared to copper–graphite composites. High surface area of nanographite particles embedded in copper matrix exhibited high adherent graphite tribo-layer at the contact surface. Formed graphite layer reduces the sub-surface deformation of the composite by way of reduced frictional force.     

Tribological behaviour of PTFE modified cotton polyester composites

Abstract

An attempt on modification of tribological behaviour of cotton polyester composite was done with polytetrafluoroethylene (PTFE). PTFE modified polyester–cotton composites were developed and studied for their friction and sliding wear behaviour at different applied loads. The sliding wear tests of composites were conducted against EN-31 steel counter face. The coefficient of friction μ as well as the sliding wear rate of cotton–polyester composites reduced significantly on addition of PTFE. The reduction in wear rate of PTFE modified polyester–cotton composite has been discussed with the help of SEM observations of worn surfaces and coefficient of friction.     

颗粒增强铝基复合材料摩擦磨损性能研究

对颗粒增强铝基复合材料及其基体与 4 0Cr钢摩擦材料组成的摩擦副的摩擦磨损特性进行了对比试验研究 ,并采用SEM对颗粒增强铝基复合材料及其基体磨损表面进行了观察 ,探讨了其磨损机理。试验表明 :复合材料具有较稳定的摩擦系数、低的磨损率 ;复合材料的主要磨损形式是磨粒磨损 ,基体材料的主要磨损形式是粘着磨损。     

Friction and wear properties of Kevlar pulp reinforced epoxy composites under dry sliding condition

In this work, the friction and wear properties of Kevlar pulp reinforced epoxy composites against GCr15 steel under dry sliding condition were evaluated on a reciprocating ball-on-block UMT-2MT tribometer. The effects of Kevlar pulp content on tribological properties of the composites were investigated. The worn surface morphologies of neat epoxy and its composites were examined by scanning electron microscopy (SEM) and the wear mechanisms discussed. The results show that the incorporation of Kevlar pulp into epoxy contributed to improve the friction and wear behavior considerably. The maximum wear reduction was obtained when the content of Kevlar pulp is 40 vol%. The friction coefficient of epoxy and its composites increased with load while increase in the sliding frequency induced a reverse effect. Fatigue wear and scuffing were notable for the neat epoxy. The fatigue cracks were greatly abated when the filler content was 40 vol%. The wear grooves appeared on the worn surface at higher filler content.     

Friction and wear behaviour of aluminium alloy coconut shell char particulate composites

The friction and wear characteristics of Al-11.8%Si alloys containing 10–25 vol.% (3–8 wt.%) dispersions of coconut shell char particles (average size, 125 μm) were evaluated under dry conditions with a pin-on-disc machine. At the lower sliding speed of 0.56 m s^?1, the wear rates and friction coefficients of the composites decreased with increasing volume per cent of dispersed char particles in the aluminium alloy matrix. Scanning electron microscopy observations have revealed the presence of adhering shell char fragments on the worn-out surface of the composites and the average roughness R_a for the worn-out surface of the composite (Al-11.8%Si-8%char) was much less (1.9 μm) than for the worn-out surface of the matrix (3.2 μm). At the higher sliding speed of 5.38 m s^?1, the wear rates increased with increasing volume per cent of dispersed char particles in the matrix and the R_a value for the composite (Al-11.8%Si-8%char) was higher (5.2 μm) than for the matrix (4.6 μm). The worn-out surface of the composites did not show the presence of adhering shell char fragments. The reduction in wear rates and friction coefficients of composites at the lower sliding speed of 0.56 m s^?1 with respect to the matrix alloy wear was attributed to the presence of adhered fragmented bits of shell char on the wearing composite surface.