Hydrothermal synthesis of S-doped TiO2 nanoparticles and their photocatalytic ability for degradation of methyl orange

A simple synthesis route to nanocrystalline S-doped TiO₂ photocatalysts by a hydrothermal method at 180 °C was developed and the photocatalytic activity of the obtained powders for the degradation of methyl orange was studied. The products were characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). The phase composition (anatase/rutile ratio) and the photocatalytic activity of the final materials were found to be markedly influenced by the amount of the incorporated sulphur. On increasing the S-dopant amount, the anatase/rutile ratio and the photocatalytic activity of the as-prepared powders increased.     

Photocatalytic activity of nanocrystalline mesoporous-assembled TiO2 photocatalyst for degradation of methyl orange monoazo dye in aqueous wastewater

In this work, nanocrystalline mesoporous-assembled TiO₂ photocatalyst was synthesized by a sol–gel process with the aid of a structure-directing surfactant and employed for the photocatalytic degradation of methyl orange azo dye (monoazo dye), as compared to various commercially available non-mesoporous-assembled TiO₂ powders. The experimental results showed that the synthesized mesoporous-assembled TiO₂ nanocrystal calcined at 500 °C provided superior decolorization and degradation performance to the non-mesoporous-assembled commercial TiO₂ powders. In addition, several operational parameters affecting the decolorization and degradation of methyl orange, namely photocatalyst dosage, initial dye concentration, H₂O₂ concentration, and initial solution pH, were systematically investigated, using the mesoporous-assembled TiO₂ nanocrystal. The optimum conditions were a photocatalyst dosage of 7 g/l, an initial dye concentration of 5 mg/l, a H₂O₂ concentration of 0.5 M, and an initial solution pH of 4.7, exhibiting the highest decolorization rate of methyl orange.     

Heterogeneous photocatalytic removal of the herbicide clopyralid and its comparison with UV/H2O2 and ozone oxidation techniques

Clopyralid is a herbicide that has recently been reported to occur in drinking water at concentrations above the Permitted Concentration Value (PCV) of 0.1 μg/L for an individual pesticide (EU directive 98/83/EC). An extensive laboratory study on clopyralid removal with UV/TiO₂, was carried out and was compared to UV/H₂O₂ and O₃ removal efficiencies. The effectiveness of three TiO₂ photocatalysts (Degussa P25, VP Aeroperl, Hombifine N) was studied and Degussa P25 was selected since it outperformed the other two. Complete removal of clopyralid was achieved with UV/TiO₂ in about 90 min at an optimum catalyst concentration of 1 g/L. Pseudo-zero-order kinetics were suitable to describe the first stage of the photocatalytic reaction in the concentration range 0.078–0.521 mM. pH was found to significantly affect the removal rates of clopyralid due to changes in TiO₂ surface charges and clopyralid ionisation degree. The rate constant was maximum at pH 5 and its value was 2.1 × 10⁻⁶ ± 4.3 × 10⁻⁷ M min⁻¹. Pure oxygen bubbled in solution was found to slightly affect unfavourably the photocatalytic removal of clopyralid as compared to air. With UV/H₂O₂ and O₃ systems, the initial removal rates were high but these systems were not effective in achieving high removal percentages overall.     

Photoelectro-Fenton combined with photocatalytic process for degradation of an azo dye using supported TiO2 nanoparticles and carbon nanotube cathode: Neural network modeling

In this work, treatment of an azo dye solution containing C.I. Basic Red 46 (BR46) by photoelectro-Fenton (PEF) combined with photocatalytic process was studied. Carbon nanotube-polytetrafluoroethylene (CNT-PTFE) electrode was used as cathode. The investigated photocatalyst was TiO₂ nanoparticles (Degussa P25) having 80% anatase and 20% rutile, specific surface area (BET) 50 m²/g, and particle size 21 nm immobilized on glass plates. A comparison of electro-Fenton (EF), UV/TiO₂, PEF and PEF/TiO₂ processes for decolorization of BR46 solution was performed. Results showed that color removal follows the decreasing order: PEF/TiO₂ > PEF > EF > UV/TiO₂. The influence of the basic operational parameters such as initial pH of the solution, initial dye concentration, the size of anode, applied current, kind of ultraviolet (UV) light and initial Fe³⁺ concentration on the degradation efficiency of BR46 was studied. The mineralization of the dye was investigated by total organic carbon (TOC) measurements that showed 98.8% mineralization of 20 mg/l dye at 6 h using PEF/TiO₂ process. An artificial neural network (ANN) model was developed to predict the decolorization of BR46 solution. The findings indicated that artificial neural network provided reasonable predictive performance (R² = 0.986).     

Chemical vapor deposition of carbon on particulate TiO2 from CH4 and subsequent carbothermal reduction for the synthesis of nanocrystalline TiC powders

The present study aims to investigate chemical vapor deposition of carbon from CH₄ on TiO₂ particles and to establish optimal conditions for the synthesis of nanocrystalline TiC powders. Mass measurements, XRD, HR-TEM and SEM were used to characterize the products at various stages of the reactions. Oxide particles gained mass rapidly at 1300 K under CH₄ atmosphere and were coated with thin pyrolytic carbon layers of 10-20 nm. XRD analysis showed that the coated powders consisted of C, TiO₂ and titanium sub-oxides. The powders containing ∼33 ± 2 wt% carbon were used for the carbothermal reduction of TiO₂ to TiC at 1600-1800 K under Ar flow. Lattice constant and mass loss of the samples increased to the levels of TiC with temperature and time. Nearly pure TiC powders with a mean particle size of ∼125 nm were synthesized at 1750-1800 K within 30 min.     

Study on photocatalytic deposition of bismuth onto nanocrystalline TiO2 by quartz crystal microbalance and electrochemical method

In situ techniques of quartz crystal microbalance (QCM), differential pulse voltammetry (DPV) and amperometric measurement were employed to investigate the adsorption Bi(III) ions and the photocatalytic deposition Bi process at the surface of nanocrystalline TiO₂. It was obtained that the adsorption of Bi(III) ions onto nanocrystalline TiO₂ accords with the pseudo-second-order reaction and the reaction rate constant k was about 13.3 g mol⁻¹ min⁻¹. In addition, the photocatalytic deposition of Bi onto the surface of TiO₂ was further investigated. It was found that photocatalytic deposition rate at the surface of TiO₂ was enhanced by increasing pH value or initial concentration of Bi(III) ions. The influence of organic hole-scavegeners on the photocatalytic deposition of Bi was also investigated, and it was obtained that formic acid may be the best for the photocatalytic reduction of Bi. The mass ratio between the Bi(III) and Bi metal deposition was calculated as 7.48:1. Therefore, it can be concluded that QCM, DPV and amperometric measurement may be effective and reliable for the investigation of the photocatalytic deposition of Bi onto the surface of nanocrystalline TiO₂.     

Preparation of TiO2 ultrafine nanopowder with large surface area and its photocatalytic activity for gaseous nitrogen oxides

TiO₂ nanopowder with a large surface area and high crystallinity was synthesized by a thermal decomposition process. The physicochemical properties of the prepared powders were examined by X-ray diffraction, transmission electron microscopy and nitrogen adsorption-desorption isotherms. The nanocrystallites of the prepared powers were considerably smaller than those of the commercial photocatalyst (Degussa, P25), and the particles had a dense polyhedral structure. In addition, the particles had a mainly disordered mesoporous structure with a pore volume that varied according to the pore size in the range of 2-20 nm. The photocatalytic activity of the prepared photocatalyst was obviously higher than that of P25 on the photodegradation of gaseous nitrogen oxides under UV_{254 + 185 nm} lamp irradiation. Above 40% relative humidity, the NO_x removal efficiency of the prepared photocatalyst was 10% higher than that of P25. Furthermore, a suitable relative humidity and longer residence time were found to enhance the photocatalytic oxidation of gaseous nitrogen oxides by UV_{254 + 185 nm} lamp irradiation and TiO₂ nanoparticles.     

Photocatalytic abatement of naphthalene catalyzed by nanosized TiO2 particles: Assessment of operational parameters

Naphthalene removal from wastewater sources was investigated in a batch slurry system using photocatalytic process as a subset of advanced oxidation processes. At low concentrations of naphthalene, the pseudo-first order rate equation on the base of Langmuir-Hinshelwood model described the degradation kinetics very well. Also, the photocatalytic process was employed to evaluate the effect of various operational parameters such as agitation speed (0–200 rpm), injected air flow (0–6 L/h), TiO₂ concentration (0–3 g/L) and UV power intensity (0–24 W). Experimental results demonstrated that by increment in the mass transfer coefficient, the agitation speed positively affected naphthalene degradation. Due to the “screening effect”, concentration of TiO₂ showed an optimum amount equal to 2 g/L. Aeration to the solution affected the amount of oxygen as an electron scavenger and so enhanced naphthalene degradation rate. Meanwhile in the absence of UV radiation to the solution, the rate of naphthalene removal decreased significantly. In other hand, augmentation in UV radiation more than 8 W had a low influence on the amount of removed naphthalene and reaction rate.     

Synthesis and photocatalytic activity of ring-like anatase TiO2 with {001} facts exposed

Developing photocatalysts with specific morphology and good photocatalytic activities promises good opportunities to discover the geometry-dependent properties. In the present work, ring-like anatase TiO₂ with dominant {001} facets exposed were successfully synthesized via a one-pot solvothermal process of tetrabutyl titanate and hydrofluoric acid solution at 180 °C for 8 h. We found that hydrofluoric acid plays an important role in the formation of ring-like TiO₂. The morphology and microstructure were investigated by scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), and Brunauer–Emmett–Teller N₂ gas adsorption–desorption isotherms. The photocatalytic activity was evaluated by photocatalytic oxidation degradation of methylene blue aqueous solution under UV light. Results showed that ring-like TiO₂ with {001} facets exposed exhibited an excellent photocatalytic activities due to its unique structure: Nanosheets with hole.     

Structure and photocatalytic performance of magnetically separable titania photocatalysts for the degradation of propachlor

A magnetic photocatalyst was prepared by modification of TiO₂ nanoparticles (Degussa P25) with nanocrystalline γ-Fe₂O₃ nanoparticles through a protective lining made up of two oppositely charged polyelectrolytes. As-prepared magnetically separable photocatalysts differing in γ-Fe₂O₃ loading (3, 8, 13, 20 and 30 wt.%) were characterized by XRD, TEM, thermal analysis, Mössbauer and magnetic measurements. The photocatalytic efficiency of the nanocomposite catalysts was evaluated using a chloroacetanilide herbicide (propachlor) in water as model compound. The primary degradation of propachlor followed pseudo-first-order kinetics according to the Langmuir–Hinshelwood model. Generally, all magnetic photocatalysts exhibit good catalytic activity towards organic pollutants, do not suffer from photodissolution and can be reused several times without any decrease in their photocatalytic activity.     

Template-assisted hydrothermal synthesis and photocatalytic activity of novel TiO2 hollow nanostructures

TiO₂ hollow nanostructures were successfully synthesized by a controlled hydrothermal precipitation reaction using Resorcinol–Formaldehyde resin spheres as templates in aqueous solution, and then removal of the RF resins spheres by calcination in air at 450 °C for 4 h. The obtained TiO₂ hollow spheres were characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, N₂ adsorption–desorption analysis, and UV–visible diffuse reflectance spectroscopy. The photocatalytic activity of the as-prepared samples was evaluated by photocatalytic decolorization of rhodamine B aqueous solution at ambient temperature under UV illumination. The results indicated TiO₂ hollow nanostructures exhibit the excellent photocatalytic activity probably due to the unique hollow micro-architectures.     

Improved performance of dense TiO2/CdSe coupled thin films by low temperature process

Dense TiO₂ and TiO₂/CdSe coupled nanocrystalline thin films were synthesized onto ITO coated glass substrate by chemical route at relatively low temperature (≤100 °C). TiO₂ films were nanocrystalline and crystallinity disappears after CdSe deposition as evidenced by X-ray powder diffraction. Surface morphology and physical appearance of films were studied from SEM and actual photo-images, reveals dense nature of TiO₂ (10-12 nm spherical grains, faint violet) and CdSe (80-90 nm spherical grains, deep brown), respectively. Presence of two absorption edges in UV spectra implies existence of separate phases rather than composite formation. TiO₂ film was found to have higher water contact angle (71°) than TiO₂/CdSe (61°) and CdSe (56°). I-V and stability tests of photo-electrochemical cells were performed with TiO₂ and TiO₂/CdSe film electrodes (under light of illumination intensity 80 mW/cm²) in lithium iodide as an electrolyte using two-electrode system.     

Efficient visible-light photocatalysts from Gd–La codoped TiO2 nanotubes

Robust visible-light Gd–La codoped TiO₂ nanotubes were successfully synthesized via an ultrasonic hydrothermal method and the photocatalytic activities were evaluated by photodegrading Rhodamine B (RB). The calcined Gd–La codoped TiO₂ nanotubes have significantly enhanced photocatalytic activities than the uncalcined ones. The La³⁺ and Gd³⁺ in the lattices of rare earth oxides may be substituted by Ti⁴⁺, creating abundant oxygen vacancies and surface defects for electron trapping and dye adsorption, accelerating the separation of photogenerated electron–hole pairs and RB photodegradation. The formation of an excitation energy level below the conduction band of TiO₂ from the binding of electrons and oxygen vacancies decreases the excitation energy of Gd–La codoped TiO₂ nanotubes, resulting in robust photocatalysts. The results suggest that Gd–La codoped TiO₂ nanotubes calcined at 500 °C are very promising for enhancing the photocatalytic activity of photocatalysts in visible-light region.     

Synthesis of titania/carbon nanotube heterojunction arrays for photoinactivation of E. coli in visible light irradiation

TiO₂/multi-wall carbon nanotube (MWNT) heterojunction arrays were synthesized and immobilized on Si(0 0 1) substrate as photocatalysts for inactivation of Escherichia coli bacteria. The vertically aligned MWNT arrays were grown on ∼5 nm Ni thin film deposited on the Si by using plasma enhanced chemical vapor deposition at 650 °C. Then, the MWNTs were coated by TiO₂ using dip-coating sol-gel method. Post annealing of the TiO₂/MWNTs at 400 °C resulted in crystallization of the TiO₂ coating and formation of Ti-C and Ti-O-C carbonaceous bonds at the heterojunction. The visible light-induced photoinactivation of the bacteria increased from MWNTs to TiO₂ to TiO₂/MWNTs, in which the bacteria could even slightly breed on the MWNTs. In addition, the TiO₂/MWNTs annealed at 400 °C showed a highly improved antibacterial activity than the TiO₂/MWNTs annealed at 100 °C. The excellent visible light-induced photocatalytic efficiency of the TiO₂/MWNTs/Si film annealed at 400 °C was attributed to formation of the carbonaceous bonds at the heterojunction, in contrast to the 100 °C annealed TiO₂/MWNTs/Si sample which had no such effective bonds.     

TiO2, TiO2/Ag and TiO2/Au photocatalysts prepared by spray pyrolysis

TiO₂, TiO₂/Ag and TiO₂/Au photocatalysts exhibiting a hollow spherical morphology were prepared by spray pyrolysis of aqueous solutions of titanium citrate complex and titanium oxalate precursors in one-step. Effects of precursor concentration and spray pyrolysis temperature were investigated. By subsequent heat treatment, photocatalysts with phase compositions from 10 to 100% rutile and crystallite sizes from 12 to 120 nm were obtained. A correlation between precursor concentration and size of the hollow spherical agglomerates obtained during spray pyrolysis was established. The anatase to rutile transformation was enhanced with metal incorporations and increased precursor concentration. The photocatalytic activity was evaluated by oxidation of methylene blue under UV-irradiation. As-prepared TiO₂ particles with large amounts of amorphous phase and organic residuals showed similar photocatalytic activity as the commercial Degussa P25. The metal incorporated samples showed comparable photocatalytic activity to the pure TiO₂ photocatalysts.     

Effect of calcination temperature on the structural properties and photocatalytic activities of solvothermal synthesized TiO2 hollow nanoparticles

TiO₂ hollow nanoparticles were prepared by the solvothermal method, calcined at different temperatures and characterized by XRD, BET, SEM, PL and FT-IR. The effects of morphology, size and calcination temperature on the photocatalytic activity of the prepared materials were discussed in detail. It was found that the calcination temperature altered the crystallinity, morphology, surface area, and the porous structure. The photocatalytic activity of the TiO₂ powders evaluated through photocatalytic degradation of gaseous acetone under UV-light irradiation, showed TiO₂ calcined at 250 °C to exhibit a higher photocatalytic activity than commercial powders (Degussa P25).     

Photoassisted mineralization of remazole red F3B over NiO/TiO2 and CdO/TiO2 nanoparticles under simulated sunlight

In this work, a series of titania-supported NiO and CdO materials were synthesized by a modified sol-gel process. The prepared photocatalysts were characterized by X-ray diffraction (XRD), UV-Vis diffuse reflectance spectroscopy (DRS), and transmission electron microscopy (TEM). The activities of titania-supported NiO and CdO photocatalysts for photocatalytic degradation of Remazole Red F3B (RR) dye, under simulated sunlight, were investigated. The photocatalytic mineralization of an RR dye solution over various NiO-x/TiO₂ and CdO-x/TiO₂ photocatalysts under simulated sunlight was investigated. It was worthy noticing that the photocatalytic activity of titania improved using the prepared catalysts. The prepared TiO₂, NiO-5/TiO₂, and CdO-2/TiO₂ photocatalysts exhibited higher photocatalytic activity under simulated sunlight than did commercial TiO₂. The prepared photocatalysts were stable after photocatalytic degradation of the dye. The observed photocatalytic mineralization of the dye was 51 and 71% over NiO-10/TiO₂ and CdO-2/TiO₂ after 180 min of irradiation, respectively. Juxtaposing a p-NiO-5/TiO₂ semiconductor provided a potential approach for decreasing charge recombination. The prepared photocatalystsNiO-5/TiO₂ and CdO-2/TiO₂ are promising composites for the solar detoxification of textile wastewater.     

Microwave hydrothermal synthesis and photocatalytic properties of TiO2/BiVO4 composite photocatalysts

TiO₂/BiVO₄ composite photocatalysts with heterojunction structures were synthesized by the one-step microwave hydrothermal method. The physical and photophysical properties of the as-prepared photocatalysts were fully characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), energy dispersive spectroscopy (EDS), UV–vis diffuse reflectance spectra, photoluminescence (PL) and BET surface area analysis. The photocatalytic activities were evaluated by the decolorization of rhodamine B under UV and simulated sun-light irradiation. The results reveal that the as-prepared TiO₂/BiVO₄ composites exhibit higher photocatalytic activities than pure BiVO₄. The 20% TiO₂/BiVO₄ sample shows the best photocatalytic activity. The enhancement of photocatalytic activity is mainly attributed to the increasing separation rate of photogenerated charge carriers. The possible photocatalytic mechanism is discussed on the basis of the calculated energy band positions.     

The degradation of an azo dye in a batch slurry photocatalytic reactor

The photocatalytic degradation of a commercial azo-reactive textile dye, Remazol Red F-3B, has been investigated in a batch slurry reactor using semiconductor catalysts like, ZnO and TiO₂, and two UV sources emitting mainly at 254 and 365 nm. Non-irradiated catalysts and non-catalyzed UV irradiation have negligible effect on the dye degradation. Initial pH, dye concentration, light power and catalyst loading as well as the catalyst type and UV wavelength are considered as process variables. The results showed that decolorization and TOC removal efficiencies of ZnO are higher under 365 nm UV. On the other hand, when two photocatalysts are compared, the decolorization performance of ZnO is higher than TiO₂ under 365 nm UV_, while TiO₂ performs better under 254 nm UV. Furthermore, from the TOC removal point, TiO₂ performs better than ZnO irrespective of the UV wavelength. TiO₂ irradiated under 254 nm UV degrades successfully both benzene and naphthalene derivatives.     

Nanoflower-like CdS and SnS2 loaded TiO2 nanotube arrays for photocatalytic wastewater treatment and hydrogen production

In this work, nanoflower-like CdS/SnS₂/TiO₂ NTs ternary heterojunction photocatalysts were synthesized by a hydrothermal method, the relationship between the morphology, microscopic morphology, crystallinity, elemental presence state and hydrogen production performance of the ternary photocatalysts were investigated by SEM, TEM, XRD and XPS, respectively. The photocatalytic performance, electrochemical property and hydrogen production capacity of CdS/SnS₂/TiO₂ NTs were compared with pure TiO₂ NTs, CdS/TiO₂ NTs and SnS₂/TiO₂ NTs. After 2 h of photocatalytic reaction, the removal efficiency of MB wastewater reached 100%, and the photocatalytic efficiencies toward RhB and Cr(VI) removal reached 86.08% and 80.93% after 3 h, respectively. The electron spin resonance (ESR) technique certified the active radical groups that played a role in the catalytic process and further investigated the possible photocatalytic mechanism. Hydrogen production per unit time achieved 97.14 μmol h^?1 cm^?2, this work provides the new technique to achieve solar energy conversion for hydrogen generation.