Novel Carbon Dioxide Microsensor Based on Tin Oxide Nanomaterial Doped With Copper Oxide

Carbon dioxide $({rm CO}_{2})$ is one of the major indicators of fire and therefore its measurement is very important for low-false-alarm fire detection and emissions monitoring. However, only a limited number of ${rm CO}_{2}$ sensing materials exist due to the high chemical stability of ${rm CO}_{2}$. In this work, a novel ${rm CO}_{2}$ microsensor based on nanocrystalline tin oxide $({rm SnO}_{2})$ doped with copper oxide (CuO) has been successfully demonstrated. The ${rm CuO}hbox{-}{rm SnO}_{2}$ based ${rm CO}_{2}$ microsensors are fabricated by means of microelectromechanical systems technology and sol-gel nanomaterial-synthesis processes. At a doping level of ${rm CuO}:{rm SnO}_{2} =1:8$ (molar ratio), the resistance of the sensor has a linear response to ${rm CO}_{2}$ concentrations for the range of 1% to 4% ${rm CO}_{2}$ in air at 450$^{circ}{rm C}$. This approach has demonstrated the use of ${rm SnO}_{2}$, typically used for the detection of reducing gases, in the detection of an oxidizing gas.      

CMOS Microelectrode Array for Electrochemical Lab-on-a-Chip Applications

Microelectrode arrays (MEAs) offer numerous benefits over macroelectrodes due to their smaller sample size requirement, small form factor, low-power consumption, and higher sensitivity due to increased rates of mass transport. These features make MEAs well suited for microfluidic lab-on-a-chip applications. This paper presents two implementations of MEAs with and without an on chip potentiostat. We first describe an 8$,times,$ 8 array of 6 $mu{rm m}$ circular microelectrodes with center to center 37 $mu{rm m}$ spacing fabricated on silicon using conventional microfabrication techniques. Pads are provided for external connections to a potentiostat for electrochemical analysis. The second implementation is an individually addressable 32$,times,$32 array of 7 $mu{rm m}$ square microelectrodes with 37 $mu{rm m}$ center to center spacing on a CMOS chip with built-in very-large-scale integration potentiostat for electrochemical analysis. The integrated CMOS MEA is post processed at the die level to coat the exposed Al layers with Au. To verify microelectrode array behavior with individual addressability, cyclic voltammetry was performed using a potassium ferricyanide $({rm K} _{3}{rm Fe}({rm CN})_{6})$) solution.      

Development of a High-k Pr $_{2}$O $_{3}$ Sensing Membrane for pH-ISFET Application

In order to develop a pH sensor having a good pH-sensing characteristic, electrolyte-insulator-semiconductor capacitors using a high-k Pr$_{2}$O$_{3}$ thin film as the sensing membrane were fabricated on silicon substrates by reactive radio frequency sputtering. The structural and morphological features of these films with annealing at various temperatures were studied by X-ray diffraction, atomic force microscopy, and X-ray photoelectron spectroscopy. The Pr$_{2}$O $_{3}$ sensing film after annealing at 900$;^{circ}$C is suggested to the increase in the interfacial SiO $_{2}$ and silicate formation, and the high surface roughness. Therefore, a physical vapor deposition Pr$_{2}$O $_{3}$ film is adopted as a new pH-sensing layer. The result produces a pH response of 52.9 mV/pH $({rm pH}=2hbox{--}12)$, a hysteresis voltage of 17.5 mV $({rm pH}=7 to 4 to 7to 10 to 7)$, and a drift rate of 2.15 mV/h (${rm pH}=7$ buffer solution).      

Magnetic Normal Modes in Squared Antidot Array With Circular Holes: A Combined Brillouin Light Scattering and Broadband Ferromagnetic Resonance Study

We present a combined experimental investigation of magnetic normal modes in an antidot lattice using both Brillouin light scattering and broadband ferromagnetic resonance. It was fabricated on a silicon substrate using optical ultraviolet lithography. The sample consisted of a 30-nm-thick ${rm Ni}_{80}{rm Fe}_{20}$ squared antidot array with circular holes whose diameter and edge-to-edge spacing are 250 and 150 nm, respectively. Experiments were performed as a function of the applied magnetic field $mu_{0}{rm H}_{rm ext}$ in the range from $-$100 to 100 mT, with ${rm H}_{rm ext}$ applied along both the square lattice axis and its diagonal. Several peaks were observed in both the Brillouin light scattering and ferromagnetic resonance spectra, and their evolution with the intensity and the direction of the applied field ${rm H}_{rm ext}$ was measured. Micromagnetic simulations enabled us to identify the modes in terms of their symmetry obtaining a good quantitative agreement with the measured frequencies. In addition, we show how the inhomogeneity of the internal field affected the properties of the magnetic eigenmodes and their localization in different regions of the antidot lattice.      

Effect of Factors on Coercivity in Sr–La–Co Sintered Ferrite Magnets

We varied the composition and sintering temperature of Sr–La–Co ferrite magnets to analyze the effects of various important factors on coercivity $(H_{rm cJ})$. We examined the effects of crystal grain size and distribution, the mechanism of magnetization reversal, the degree of crystal grain orientation (OD), and the anisotropy field $(H_{rm A})$ on $H_{rm cJ}$. We proposed an equation based on the experimental results that expresses the measured $H_{rm cJ}$ and considers these effects as $H_{rm cJ} = C_{rm t}(0.4/R_{rm h})$ OD $(H_{rm A} - H_{rm d} - H_{rm in})$, where $C_{rm t}, R_{rm h}, H_{rm d}$, and $H_{rm in}$ are the crystal grain size effects on $H_{rm cJ}$ of sintered magnet, rotational hysteresis integral corresponding to the mechanism of magnetization reversal, demagnetizing field of shape anisotropy, and interaction field between crystal grains, respectively. We found that apart from the volume ratio for single-domain crystal grains and $H_{rm A}$, the mechanism of magnetization reversal had significant effects on $H_{rm cJ}$ for Sr–La–Co sintered ferrite magnets.      

Electromagnetic Forces Acting on the Planar Armature of a Core-Type Synchronous Permanent-Magnet Planar Motor

The core-type synchronous permanent-magnet planar motor (SPMPM) discussed in this paper includes one or more planar armatures each of which contains two sets of three-phase windings named ${rm x}$-winding and ${rm y}$-winding. For each planar armature, a magnetic field energy equation is established first. This equation describes the mechanism of the coupling between the permanent-magnet array, the ${rm x}$-winding and the ${rm y}$ -winding in the core-type SPMPM. By using virtual work principle, ${rm x}$-direction thrust force, ${rm y}$ -direction thrust force and vertical force acting on the planar armature are modeling analytically. For eliminating the coupling in these force models, the excitation flux linkages and phase currents are all transformed into ${rm d}hbox{-}{rm q}$ synchronous reference frame. From the decoupling force equations, some characteristics of the vertical component of force on the planar armature are obtained. The electromagnetic force model is helpful for the design of the contactless planar bearing and the servo control system of the SPMPM.      

Thermal Diffusivity and Related Properties of Colossal Magnetoresistive La$_{0.67}$Ca$_{0.33}$MnO $_{3}$ With Various Grain Sizes

Using the open-cell photoacoustic technique, we have measured the room-temperature thermal diffusivities of the colossal magnetoresistive material La$_{0.67}$Ca$_{0.33}$MnO$_{3 }$, sintered between 1100$;^{circ}$ C and 1350$;^{circ}$ C, with average grain sizes 1, 3, 5, and 10 $mu$m. We obtained the thermal diffusivities by analyzing the phase of photoacoustic signals in thermally thick samples using Calderon's method. We found that the insulator-metal transition temperature does not depend on the grain size ($T_{rm IM} sim 272$ K). However, the thermal diffusivity increases with grain size, with values between 0.431 and 0.969 mm $^{2}$s $^{-1}$. Other related electrical and thermal properties, including the electrical conductivity, thermal conductivity, and phonon mean free path, are also dependent on the grain size. The electronic contribution to the thermal conductivity is 2%–3% of the total thermal conductivity for smaller grain sizes (1–5 $mu$m) and increases to about 24% when the grain size is increased to 10 $mu$ m.      

Planar Optical Waveguide Evanescent Wave ${rm CO}_{2}$ Sensor Based on a Clad of Alstonia Scholaris Leaf Extract

An evanescent wave biosensor is designed and developed using a single mode planar optical waveguide based on a spin coated clad of leaf extract of Alstonia Scholaris. The fabricated sensor showed ${rm CO}_{2}$ concentration dependent response. The specialty of this sensor is that it can be used when stored at room temperature (25$~^{circ}{rm C}$) up to a maximum of 25–30 days with 90% retention of original sensitivity. These ${rm CO}_{2}$ sensing biochips showed good operational efficiency for 10 cycles. The planar optical waveguide is versatile, easy to fabricate and can be used for ppm level ${rm CO}_{2}$ measurement with good sensitivity. Cross sensitivity with respect to humidity is studied. The sensor exhibited a short response time of 4–5 s and recovery time of 25 s with good repeatability and reproducibility.      

Comparison of Alternative Techniques for Characterizing Magnetostriction and Inverse Magnetostriction in Magnetic Thin Films

We compare the direct and inverse techniques of measuring magnetostriction in magnetic thin films. We chose a set of four magnetic thin film samples (Co$_{95}$Fe$_5$, Co$_{60}$Fe$_{20}$B$_{20}$, Ni$_{65}$Fe$_{15}$Co$_{20}$, and Ni$_{80}$Fe$_{20}$) for the measurements, representing positive and negative magnetostriction and having saturation magnetostriction of magnitudes ranging from $10^{-7}$ to $10^{-5}$. We made the direct measurements on a high-precision optical cantilever beam system, and we carried out the inverse magnetostriction measurements on a nondestructive inductive $Bhbox{-}H$ looper with three-point bending stage.      

Optimization of Spin-Valve Structure NiFe/Cu/NiFe/IrMn for Planar Hall Effect Based Biochips

This paper deals with the planar Hall effect (PHE) of Ta(5)/NiFe$(t_{rm F})$/Cu(1.2)/NiFe$(t_{rm P})$/IrMn(15)/Ta(5) (nm) spin-valve structures. Experimental investigations are performed for 50 $mu$m$times hbox{50} mu$m junctions with various thicknesses of free layer ( $t_{rm F} = 4, 8, 10, 12, 16, 26$ nm) and pinned layer ($t_{rm P} = 1, 2, 6, 8, 9, 12$ nm). The results show that the thicker free layers, the higher PHE signal is observed. In addition, the thicker pinned layers lower PHE signal. The highest PHE sensitivity $S$ of 196 $mu$V/(kA/m) is obtained in the spin-valve configuration with $t_{rm F} = 26$ nm and $t_{bf P} = 1$ nm. The results are discussed in terms of the spin twist as well as to the coherent rotation of the magnetization in the individual ferromagnetic layers. This optimization is rather promising for the spintronic biochip developments.      

Smooth Contact Capacitive Pressure Sensors in Touch- and Peeling-Mode Operation

Capacitive (C) pressure sensors typically sense quadratic changes in $C$ as a pressure difference $(P)$ deflects a flexible conducting diaphragm near a rigid ground plane. Touch-mode capacitive pressure (C-P) sensors, where the conducting diaphragm touches a dielectric coated ground plane, often show a more linear response, but with less sensitivity, particularly at low-$P$ . Initial contact of the diaphragm often occurs at a critical $P$. Until $P_{rm crit}$ is reached, the sensitivity is typically too low for accurate measurements. In this work, two different types of electrodes with “parabolic” and “donut” cavity-shapes have been designed, fabricated, and tested to achieve high-sensitivity at low-pressures. A flexible conducting diaphragm touches the bottom electrode smoothly, and both cavity shapes permit initial contact at a zero-pressure differential. This type of C-P sensors can have touch-mode and peeling-mode operations. The sensitivities of these sensors in two operation modes were measured, and their resolutions were smaller than 0.1 Pa at a mean pressure of ${10} ^{5}~{rm Pa}$. Both sensors in two modes have the resolution over total-pressure less than ${10} ^{-6}$, which is difficult to achieve at atmospheric pressure.      

Combinatorial Screening of the BiDyYb Iron Garnet Material System for High Kerr Rotation Composition

We investigated the $(hbox{Bi}_{rm x}hbox{Dy}_{rm y}hbox{Yb}_{3-{rm x}-{rm y}})hbox{Fe}_{5}hbox{O}_{12}$ ternary combinatorial composition spread with the goal of finding new compositions with a large magneto-optical effect for possible use as magneto-optical storage materials. High-throughput magneto-optical characterization of the spread showed that the $hbox{Dy}_{0.6}hbox{Yb}_{0.5}hbox{Bi}_{1.9}hbox{Fe}_{5}hbox{O}_{12}$ composition has the largest Kerr effect in this ternary system. After annealing at 690 $^{circ}hbox{C}$ for 1 h, a scaled-up thin-film sample of this composition has a remanent magnetization as high as 90% of its saturation magnetization, indicating a good storage application potential.      

Fabrication and Application of Ruthenium-Doped Titanium Dioxide Films as Electrode Material for Ion-Sensitive Extended-Gate FETs

A novel ruthenium-doped titanium dioxide (TiO $_{2}$: Ru) film for pH detection is based on an ion-sensitive extended gate field effect transistor (ISEGFET) sensor. For the preparation of the TiO$_{2}$ : Ru sensing film, a specific processing for metal modification of TiO$_{2}$ thin film is deposited by a co-sputtering system. After thermal annealing treatment, material analysis of the sensing layer is measured by SEM, Hall measurement system and electrical detection system. The average sensitivity of TiO$_{2}$: Ru for hydrogen ion detection is about 55.20 mV/pH (concentration range between pH1 and pH13). The effect of long-term drift for TiO$_{2}$ : Ru ISEGFET-based sensor is presented. Drift rate of the sensor for pH is 0.745 mV/h for 12 h. In order to prepare the calcium ion sensor, the sensing membrane of polymer materials is based on TiO $_{2}$: Ru ISEGFET-based sensor by physical adsorption. The average sensitivity of the calcium ion sensor in the concentration ranging between 1 M and 1$,times,$ 10$^{-3}$ M CaCl$_{2}$ is about 29.65 mV/pCa.      

Full Wheatstone Bridge Spin-Valve Based Sensors for IC Currents Monitoring

Full Wheatstone bridge spin-valve-based electrical current sensors at the IC level are presented. Prototypes with different geometrical parameters have been designed, fabricated and fully characterized. DC characterization has been carried out, for measurement of insertion losses, linearity, voltage offset and sensitivity. Current ranges from 10 $mu{rm A}$ to 100 mA can be covered with these sensors with excellent linearity and sensitivities above 1 ${rm mV}/({rm V}cdot{rm mA})$ . AC characteristics have also been analyzed and bandwidths exceeding 100 kHz are demonstrated. Moreover, the temperature coefficients have been extracted in the range of $-20^{circ}{rm C}$ to $+60^{circ}{rm C}$. In order to highlight the design properties, dependence of the sensor's performance with external magnetic perturbations and self-heating have also been measured and quantified. The associated errors are in the range of 1%–2% of the full scale.      

Microstructure, Electrical, and Magnetic Properties of ZrO$_{2}$ Added MnZn Ferrites

We investigated the influence of ZrO$_{2}$ on the microstructure and electromagnetic properties of MnZn ferrites by characterizing fracture surface micrographs, magnetic properties, and dc resistivity. Powders of Mn $_{0.68}$Zn $_{0.25}$Fe $_{2.07}$O $_{4}$ composition were prepared by the conventional ceramic technique. Toroidal cores were sintered at 1350 $^{circ}$C for 4 h in N$_{2}$/O$_{2}$ atmosphere with 4% oxygen. The results show that the lattice constant and average grain size increase with ZrO$_{2}$ concentration, but excessive ZrO $_{2}$ concentration will result in exaggerated grain growth and porosity increase. The dc resistivity, activation energy, saturation magnetic flux density, and initial magnetic permeability increase monotonically when the ZrO$_{2}$ concentration is not more than 0.04 wt% and then decrease with further increase of ZrO$_{2}$ concentration. On the other hand, the porosity, drift mobility, resonance frequency, and core loss decrease initially and then increase with the increase of ZrO$_{2}$ concentration.      

Effects of Post-Deposition Annealing and Oxygen Content on the Structural and pH-Sensitive Properties of Thin Nd $_{2}$O $_{3}$ Films

This paper describes the structural properties and sensing characteristics of thin Nd$_{2}$O$_{3}$ sensing membranes deposited on silicon substrates by means of reactive sputtering. X-ray diffraction, X-ray photoelectron spectroscopy, and atomic-force microscopy were used to study the chemical and morphological features of these films as functions of the growth conditions (argon-to-oxygen flow ratios of $20/5, 15/10$ and $10/15$; temperatures ranging from 600$~^{circ}$C to 800$~^{circ}$C). The thin Nd$_{2}$O$_{3}$ electrolyte-insulator-semiconductor devices prepared under a 15/10 flow ratio with subsequent annealing at 700$~^{circ}$C exhibited a higher sensitivity (56.01 mV/pH, in the solutions from pH 2 to 12), a smaller hysteresis voltage (4.7 mV in the pH loop $7 to 4 to 7to 10 to 7$), and a lower drift rate (0.41 mV/h in the pH 7 buffer solution) than did those prepared at the other conditions. We attribute this behavior to the optimal oxygen content in this oxide film forming a high density of binding sites and a small surface roughness.      

A Phototransistor-Based High-Sensitivity Biosensing System Using 650-nm Light

A miniature optical biosensing system based on a PMOS phototransistor and absorption photometry is proposed. The phototransistor was manufactured in a standard 0.35-$mu{rm m}$ CMOS process, and it exhibited a responsivity higher than 1000 A/W for 650-nm light. For biochemical applications, the ${rm TMB/H}_{2}{rm O}_{2}/{rm HRP}$ method was adopted as a useful basis in our system. A sample volume of only 10 $mu{rm l}$ was required to be dropped on the slide above the phototransistor. Experimental results demonstrated that a high sensitivity of 2.5 $mu{rm A/pM}$ was achieved, and the minimum HRP concentration successfully detected was 2.7 pM. This detection limit is three orders of magnitude better than that of a lately reported silicon biosensor, and is even comparable to that of a commercial spectrophotometer.      

A Stabilized Fiber Laser for High-Resolution Low-Frequency Strain Sensing

We frequency stabilize a fiber laser for use in low-frequency sensing applications. Using a radio frequency locking technique, an Erbium-doped single longitudinal mode fiber laser is stabilized to a Mach–Zehnder interferometer. The low-frequency fiber laser noise was suppressed by more than 1.5 orders of magnitude at frequencies below 300 Hz reaching a minimum of 2 ${rm Hz}/sqrt {rm Hz}$ between 60 and 250 Hz. The corresponding strain sensitivities are 2 ${rm p}epsilon /sqrt {rm Hz}$ at 1 Hz and 15 ${rm f}epsilon /sqrt {rm Hz}$ from 60 to 250 Hz.      

Development of a New Selective Optical Sensor for Cd(II) Ions Based on 4-Hydroxy Salophen

A new sensor membrane based on immobilization of 4-hydroxy salophen on triacetyl cellulose has been developed for the determination of Cd(II) ions that displays excellent performance. The sensing membrane is capable of spectrophotometric determining of Cd(II) with an outstanding high selectivity over a dynamic range between 1.0$,times 10^{-6}$ and 5.0$,times 10^{-2}$ mol L$^{-1}$ with a limit of detection of 5.3 $,times 10^{-7}~$mol L $^{-1}$ (0.06 $mu$g mL $^{-1}$ The sensor shows a fast response time ($≪ {5}~$ min) and the membrane can be used for more than two months without observing any major deviation. The optode revealed very good selectivity with respect to many cations including alkali, alkaline earth, transition and heavy metal ions. The proposed sensor could be used to determine cadmium ions in water and waste water samples. Different experimental parameters such as variable affecting on sensor preparation and pH of the sample solution plus response time were studied. The optodes developed in the present work were found to be stable, cost effective, easy to prepare, and efficient for direct determination of Cd(II) in a variety of aqueous samples using spectrophotometry, with satisfactory results.      

Proposal of a Novel Pole Type Structures in Perpendicular MRAM for High Gb/Chip

This paper proposes a novel MRAM using perpendicular magnetic tunnel junction device for high capacity. Conventional MRAM has weak points to realize high capacity in the design structure of the cell, one of which is that using simple current injection system can generate only weak switching field. As a solution, we propose a novel MRAM that has two additional poles in this paper. Proposed novel MRAM has a strong switching field owing to two poles added on both sides of the free layer, just like perpendicular magnetic recording heads. In this paper, analysis of the switching field and useful designs for high Gb/Chip are presented. This research was done using three dimensional FEM with injected current density of $8times 10^{7}$ A/cm$^{2}$ –$6times 10^{8}$ A/cm$^{2}$ .