Hydraulic Conductivity of Nonprehydrated Geosynthetic Clay Liners Permeated with Inorganic Solutions and Waste Leachates

To investigate systematically the effects of electrolytic solutions on the barrier performance of geosynthetic clay liners (GCLs), a long-term hydraulic conductivity test for 3 years at longest was conducted on a nonprehydrated GCL permeated with inorganic chemical solutions. The hydraulic conductivity test for waste leachates was also conducted. The results of the test show that the hydraulic conductivity of GCLs significantly correlates with the swelling capacity of bentonite contained in GCLs. GCLs have excellent barrier performance of k<1.0×10^-8 cm/s when the free swell is larger than 15 mL/2 g-solid regardless of the type and concentration of the permeant solution. In addition, when the results of the hydraulic conductivity test with chemical inorganic solutions were compared to those with waste leachates, the hydraulic conductivity of GCL permeated with chemical solution was almost the same within the electric conductivity of 0-25 S/m as that permeated with waste leachate having similar electric conductivity. The hydraulic conductivity of GCLs to be used in landfill bottom liners can be estimated by the hydraulic conductivity values obtained from the experiment using chemical solutions having the similar electric conductivity values, if the chemical solution had the electric conductivity within=25 S/m.     

Hydraulic conductivity of geosynthetic clay liners to tailings impoundment solutions

The results of a comprehensive testing program conducted to evaluate the hydraulic conductivity (k) of two geosynthetic clay liners (GCLs) considered as a liner component for a tailings impoundment at a proposed zinc and copper mine are reported. The two GCLs were permeated with a relatively low ionic-strength ground water (GW) from the mine site and two electrolyte solutions, a process water (PW) and a simulated leachate (SL), with chemical compositions consistent with those expected during operation of the impoundment. A total of 22 flexible-wall tests were performed to determine the effects of prehydration with the GW, type of GCL, type of permeant liquid, and duration of the back-pressure stage of the test. The k values for both GCLs permeated with the GW were 1.7 × 10⁻⁹ cm/s, which is within the range 1–3 × 10⁻⁹ cm/s typically reported for GCLs permeated with low ionic-strength liquids, such as deionized water. However, the mean values of k based on permeation of duplicate specimens of both types of GCL with either PW or SL relative to the values of k based on permeation with GW, or k/k_w, ranged from a factor of 200 (2.3 orders of magnitude) to a factor of 7600 (3.9 orders of magnitude). Thus, both tailings impoundment solutions had significant adverse impacts on the hydraulic performance of both GCLs. Given the overall range of k/k_w values, factors such as prehydration, type of GCL, type of permeant liquid, and duration of back pressure, were relatively insignificant. The results of this study serve to emphasize the need to perform hydraulic conductivity testing using site specific materials.     

Hydraulic conductivity of bentonite-polymer composite geosynthetic clay liners permeated with bauxite liquor

The high ionic strength of the porewater in red mud (bauxite liquor from digestion) can suppress swelling of montmorillonite, resulting in geosynthetic clay liners (GCLs) that are too permeable to be effective as liners in red mud disposal facilities. Bentonite-polymer composite GCLs (BPC GCLs) have been developed as more resilient lining materials, and some BPC GCLs have been shown to have very low hydraulic conductivity to bauxite liquors that have extreme ionic strength and pH. In this study, a nationwide investigation was conducted in China to evaluate the characteristics of bauxite liquor in Chinese impoundments, and to evaluate the suitability of GCLs containing granular sodium bentonite or BPCs for containment. Hydraulic conductivity tests were conducted on six BPC GCLs with two characteristic Chinese bauxite liquors that are hyperalkaline (pH > 12) and had ionic strengths of 76.9 mM and 620.3 mM. The BPC GCLs had hydraulic conductivity ranging from 10^?8-10^?12 m/s, which is higher than the hydraulic conductivity of BPC GCLs to deionized water (10^?12-10^?13 m/s), but lower than the hydraulic conductivity of conventional GCLs with granular sodium bentonite GCLs to the same liquors (10^?7-10^?8 m/s). The hydraulic conductivity of the BPC GCLs depends on the chemical properties of the leachate, the polymer loading, and the type of polymer. Microstructural analysis by scanning electron microscopy (SEM) suggests that the hydraulic conductivity of BPC GCLs is controlled by pore-blocking by polymer hydrogel, which is affected by the bauxite liquor.     

Interface transmissivity of conventional and multicomponent GCLs for three permeants

A laboratory investigation of the interface transmissivity is reported for five different geosynthetic clay liners (GCLs) and a range of different geomembranes (GMBs) for a range of stresses from 10 to 150?kPa. The GCLs were prehydrated under normal stress before permeation. The GCLs examined comprised three multicomponent (a smooth coated, a smooth laminated, and textured coated) and two conventional (one with granular and one with powdered sodium bentonite) GCLs. The effect of a 4?mm circular defect in the coating of a multicomponent GCL directly below the 10?mm diameter hole in the GMB is investigated. The effect of GMB stiffness and texture is examined. Additionally, the effect of hydration and permeation of smooth coated GCL with highly saline solution and synthetic landfill leachate (SL3) is presented. It is shown that the 2-week interface transmissivity (θ_2-week) can be one to two orders of magnitude higher than steady-state interface transmissivity (θ _steady-state) at low stresses (10?kPa–50?kPa), whereas at high stresses (150?kPa) the variation is substantially less. For a smooth coated GCL hydrated and permeated with reverse osmosis (RO) water, GMB stiffness and texture has a limited effect on interface transmissivity when the coating is placed in contact with GMB at normal stresses of 10?kPa–150?kPa, whereas coating indentations result in much high interface transmissivity when placed in contact with GMB. GCL prehydration and permeation with highly saline solutions leads to higher interface transmissivity compared to RO water. With a 4.0?mm defect in the coating, the interface transmissivity between the coating and woven geotextile is higher than that between the coating and GMB for the stress levels and GCL examined.     

Investigating factors influencing polymer elution and the mechanism controlling the chemical compatibility of GCLs containing linear polymers

A study was conducted to investigate (1) physicochemical factors that influence polymer elution from GCLs containing a blend of bentonite and linear (water-soluble) polymer (LPB GCLs) and (2) the mechanism that controls the chemical compatibility of LPB GCLs when polymer elutes. A series of hydraulic conductivity (k), free swell and viscosity tests were performed on a commercial LPB GCL using DI water, varying concentrations of NaCl and CaCl?. Comparable tests were also performed on a conventional bentonite (CB) GCL containing the same untreated bentonite and the same physical properties as the LPB GCL. The LPB GCL showed improved swelling and hydraulic performance compared to the CB GCL when permeated with salt solutions. Total organic carbon analysis of the effluents showed that polymer eluted from the LPB GCL regardless of the permeant solution. However, the rate at which polymer eluted increased as the concentration and valence of the dominant cation increased. The rate at which polymer eluted also increased with hydraulic gradient. The mass of polymer retained inside the GCL matrix did not correlate with the k of the LPB GCL. Free swell tests coupled with chemical analysis suggest that, the improved chemical compatibility of the LPB GCL was due to the ability of the polymer to scavenge cations from the solution which allows the bentonite to undergo adequate swelling during the initial hydration period. Analogous to water-prehydrated CB GCLs, the dispersed structure of the bentonite fabric and increased adsorbed water molecules attained during initial swelling controls the k of the LPB GCL when polymer elutes.     

Impact of a synthetic leachate on permittivity of GCLs measured by filter press and oedopermeameter tests

Geosynthetic clay liners (GCLs) are used in landfill liner applications due primarily to their low hydraulic conductivity to water. The low hydraulic conductivity of GCLs comes from the structure of the clay in the bentonite. However, the interaction between clay and aggressive liquids may alter the structure of the clay and, thus, result in an increase in the hydraulic conductivity of the GCL. This paper presents the results of a project aimed at evaluating the impact of a synthetic leachate on the structure of four different bentonites used in the manufacturing of GCLs. The preparation of bentonite dispersions increased the interaction between the bentonites and the various liquids. The hydraulic properties of the dispersions also were tested using filter press tests to obtain flow curves. Results of these tests were correlated with the cationic concentration, electrical conductivity and pH of the dispersions, swell indexes of the bentonite extracted from the GCLs, and permittivities of the intact GCLs determined in oedopermeameter tests. The results showed that one bentonite was more sensitive to the synthetic leachate than the other bentonites. For example, the permittivities of the more sensitive bentonite based on the oedopermeameter tests and filter press tests were respectively 2.11 × 10⁻⁸ s⁻¹ and 5.6 × 10⁻⁸ s⁻¹, whereas the permittivities for other bentonites, including a natural sodium bentonite and two sodium-activated calcium bentonites, were respectively 5.7 to 6.5 × 10⁻⁹ s⁻¹ and 3.2 to 3.5 × 10⁻⁸ s⁻¹. The filter press test served as a quick and easy-to-use test to compare the performance of the various bentonites in containing a given liquid. However, the oedopermeameter test or direct permeation test is preferable to filter press tests or fluid loss tests for evaluating the long-term impact of a liquid on a bentonite.     

Hydraulic conductivity of bentonite-polymer geosynthetic clay liners to coal combustion product leachates

Hydraulic conductivity of seven geosynthetic clay liners (GCLs) to synthetic coal combustion product (CCP) leachates were evaluated in this study. The leachates are chemically representative of typical and worst scenarios observed in CCP landfills. The ionic strength (I) of the synthetic CCP leachates ranged from 50 mM to 4676 mM (TCCP-50, LRMD-96, TFGDS-473, LR-2577, HI-3179 and HR-4676). One of the GCLs contained conventional sodium bentonite (Na–B) and the other six contained bentonite-polymer (B–P) mixture with polymer loadings ranging from 0.5% to 12.7%. Hydraulic conductivity tests were conducted at an effective confining stress of 20 kPa. The hydraulic conductivity of the Na–B GCLs were >1 × 10⁻¹⁰ m/s when permeated with all six CCP leachates, whereas the B–P GCLs with sufficient polymer loading maintained low hydraulic conductivity to synthetic CCP leachates. All the B–P GCLs showed low hydraulic conductivity (<1 × 10⁻¹⁰ m/s) to low ionic strength leachates (TCCP-50, I = 50 mM and LRMD-96, I = 96 mM). B–P GCLs with P > 5% showed low hydraulic conductivity (<1 × 10⁻¹⁰ m/s) up to HI-3179 leachates. These results suggest that B–P GCLs with sufficient polymer loading can be used to manage aggressive CCP leachates.     

Combined effects of ammonium permeation and dry-wet cycles on the hydraulic conductivity and internal properties of geosynthetic clay liners

The hydraulic conductivity of geosynthetic clay liners (GCLs) permeated with deionized water (S0) and NH₄⁺ solutions, with concentrations of 100 mg/L (S100) and 1000 mg/L (S1000), was examined under six dry-wet cycles. The internal properties of virgin, desiccated, and healed GCLs were analyzed and quantified using X-ray computed tomography images. The hydraulic conductivity of the GCLs permeated with S0 and S100 underwent a negligible change during the six dry-wet cycles, whereas that of S1000 increased by almost three orders of magnitude after two desiccations. Each desiccation, after permeating with S0 and S100, generated a completely different macro-crack pattern; however, generation of macro-cracks at the same locations from dry cycles 2 to 6 and an abundance of micro-cracks were typical for S1000. This implies the severe deterioration of bentonite due to multi-desiccations and chemical compatibility with S1000. Moreover, the swell index of bentonite exposed to S1000 was reduced by approximately half, after six dry-wet cycles. Despite the lower volume percentage of macro-cracks for S1000 compared to S0 and S100, the swelling capacity of this bentonite was insufficient to fully heal these cracks. Hence, the swelling properties of bentonite dominate crack volume with regard to determining the hydraulic conductivity of GCLs.     

Suction and crack propagation in GCLs subjected to drying and wetting in CaCl2-solutions

The current study addresses the cracking and self-healing capacity of Geosynthetic clay liners (GCLs) subjected to drying and wetting in a divalent salt solution. Commercially available GCLs, initially saturated under a load of 3.92 kPa, were stepwise dried for different durations in an oven at 30 °C and rewetted afterwards in deionised water and divalent salt solutions (CaCl₂) of different molarities (0.05 mol/l, 0.5 mol/l and 0.05 mol/l prehydrated). The evolution of cracks and their patterns were studied by analysing X-ray images. In parallel, the water retention behavior was tested on the raw bentonite using micro-cells and a chilled-mirror hygrometer. The morphology of the crack patterns in the GCLs was highly affected by the pore fluid, which was reasoned by reduced tensile strength caused by the salt induced aggregation. The ability to retain water at a given suction was found to be higher for the samples subjected to CaCl₂-solutions in comparision to the sample saturated with deionised water. However, a calculation of the osmotic suction caused by the additional CaCl₂ in the porewater shows that the matric suction of the samples subjeted to CaCl₂ decreases. The crack intensitiy factor (CIF) followed a similar trend and three different drying regimes were identified.     

Hydraulic performance and chemical compatibility of a powdered Na-bentonite geosynthetic clay liner permeated with mine drainage

The hydraulic and chemical compatibility of a geosynthetic clay liner (GCL), containing powdered Na-bentonite, was evaluated against artificial acid rock drainage (ARD) in terms of the swell index, hydraulic conductivity and heavy metal retention. Six artificial ARDs with an approximate pH of 3 and different metal concentrations (electrical conductivity, EC, ranging between 75 and 1000 mS/m; ionic strength ranging between 8 and 400 mM) were used in the experiments. The results of free swelling tests showed that high metal concentrations (EC higher than 70 mS/m) negatively impact the swell volume by lowering it. The hydraulic conductivity of the GCL permeated with distilled water was 1.2 × 10^?11 m/s, falling in the range of 7.9 × 10^?12 to 1.1 × 10^?10 m/s when prehydrated with distilled water and permeated with ARDs. The ion exchange and metal precipitation appeared to be the main mechanisms controlling the metal attenuation on the bentonite. The ion exchange mechanism starts with the release of Na from the bentonite and the sorption of the bi- and tri-metals present in the ARDs onto the bentonite. After the depletion of Na, the ion exchange reaction proceeds with the desorption of Ca and Mg from the bentonite and the sorption of cations present in the ARDs onto the bentonite layers. The depletion of Na from the bentonite and the subsequent release of Ca and Mg correlate to the sudden drop in pH and a gradual increase or equilibration of the hydraulic conductivity. It is possible to say that, after this point, hydraulic and chemical equilibrium is reached. From the overall results, the tested GCL showed acceptably low hydraulic conductivity and the potential to attenuate heavy metals present in ARDs.     

Effect of prehydration,permeant, and desiccation on GCL/Geomembrane interface transmissivity

A laboratory investigation was conducted on two different conventional GCLs (one with fine granular and another one with powdered bentonite) to explore the effect of prehydration and permeant fluid; GCL desiccation on the interface transmissivity, θ, between the interfaces of a 1.5 mm-thick high-density polyethylene (HDPE) geomembrane (GMB) and a GCL. The study also aimed to assess the self-healing capacity of desiccated GCLs for three different permeant solutions under a range of applied stresses (10–150 kPa). It was found that at stresses less than 70 kPa, θ was dominated by variability in the initial contact condition between the GMB-GCL interfaces. The effect of other factors was largely masked by the contact variability. At 100–150 kPa, the effects of initial variability were largely eliminated, but there was no notable effect of other factors on θ in the absence of desiccation. GCL desiccation increased θ by up to three orders of magnitude than an intact specimen at 10–100 kPa. Even at 150 kPa, desiccated specimens had a θ ≤ 8.0 × 10⁻⁹ m²/s for all specimens tested. The chemical composition of the permeant solutions, crack width, and nature of bentonite could play an important role in healing the cracks of desiccated GCLs.     

Chemical interaction and hydraulic performance of geosynthetic clay liners isothermally hydrated from silty sand subgrade

The effects of the silt aggregation, compaction density, and water content of the subgrade on the hydration of five different geosynthetic clay liner (GCL) products is reported based on a series of laboratory column experiments conducted over a six-year period. GCLs meeting typical specifications in terms of minimum hydraulic conductivity and swell index are hydrated to equilibrium from the same subgrade soil with sufficient cations to cause cation exchange during hydration. It is then shown that the GCL bentonite granularity and GCL structure can have a significant (~four orders of magnitude) effect on hydraulic conductivity under the same test conditions (from 8 × 10⁻¹² m/s for one GCL to 6 × 10⁻⁸ m/s for another GCL product). The effect of subgrade water content on the hydraulic performance of GCLs are not self-evident and quite dependent on the bentonite granularity, GCL structure, and permeant. Varying the subgrade water content from 5 to 16% and allowing the GCL to hydrate to equilibrium before permeation led to up to 5-fold difference in hydraulic conductivity when permeated with tap water and up to 60-fold difference when the same product is permeated with synthetic municipal solid waste leachate. When permeated with synthetic leachate, increasing stress from 70 kPa to 150 kPa led to a slight (average 37%; maximum 2.7-fold) decrease in hydraulic conductivity due to a decrease in bulk void ratio. It is shown that hydraulic conductivity is lower for GCLs with a scrim-reinforced geotextile, and/or with finer bentonite. It is shown that selecting a GCL based on the initial hydraulic conductivity and swell index in a manufacturers product sheet provides no assurance of good performance in field applications and it is recommended that designers pay more attention to selection of a GCL and preparation of the subgrade for important projects.     

Investigation of initial hydration and rehydration of geosynthetic clay liners from sandy subgrades via X-ray computed tomography images

The hydraulic conductivity of geosynthetic clay liners (GCLs) widely used as barrier systems considerably depends on their hydration status after the initial hydration of virgin GCLs and the rehydration of desiccated GCLs. Free hydration tests were performed on virgin and desiccated GCLs over sandy subgrades to compare their hydration level. In addition, high-resolution micro-X-ray computed tomography (CT) images of both GCLs and sandy subgrades with different gravimetric water content (i.e. 15%, 20%, and 25%) after the initial hydration were analyzed for better insights. The results show significant influences of subgrade water content on moisture content and thickness of virgin GCLs. Water loss of sandy subgrades and the time interval necessary for reaching a steady state of desiccated GCLs during rehydration was greater and longer than virgin GCLs during initial hydration. X-ray CT images verified a dense distribution of bentonite particles, macropores, and minor desiccation cracks that existed in poorly-hydrated GCLs over unsaturated sand. On the other hand, the completely saturated sandy subgrade facilitated the hydration of GCLs, leaving a lot of macropores in the sand. The relationship between water distribution and the frequency of macropore generation observed in the upper contact zone of sandy subgrades was also indicated via these X-ray CT images.     

Hydrodynamic assessment of bentonite granule size and granule swelling on hydraulic conductivity of geosynthetic clay liners

Flow in an idealized geosynthetic clay liner (GCL) containing bentonite comprised of equisized and equispaced square granules was simulated using a hydrodynamic model to quantitatively evaluate the premise that the hydraulic conductivity of GCLs diminishes as the bentonite granules hydrate and swell into adjacent intergranular pores, creating smaller and tortuous intergranular flow paths. Predictions with the model indicate that hydraulic conductivity decreases as granules swell and intergranular pores become smaller, and that greater granule swelling during hydration is required to achieve low hydraulic conductivity when the bentonite is comprised of larger granules, or the bentonite density is lower (lower bentonite mass per unit area). Predictions made with the model indicate that intergranular pores become extremely small (<1 μm) as the hydraulic conductivity approaches 10⁻¹¹ m/s. These outcomes are consistent with experimental data showing that GCLs are more permeable when hydrated and permeated with solutions that suppress swelling of the bentonite granules, and that the hydraulic conductivity of GCLs with bentonite having smaller intergranular pores (e.g., GCLs with smaller bentonite granules, more broadly graded particles, or higher bentonite density) is less sensitive to solutions that suppress swelling.     

Hydraulic conductivity of two geosynthetic clay liners permeated with a hyperalkaline solution

GCLs containing powdered Na-bentonite treated with different dosages of a proprietary additive intended to reduce the impacts of chemical interactions were permeated with three solutions: a hyperalkaline solution (1 M NaOH and 1.3 mM CsCl) having similar pH to aluminum refining leachate, a 1.3 mM CsCl solution (no NaOH), and DI water. For a given permeant solution, the hydraulic conductivity of both GCLs was similar. Thus, the higher additive dosage had no measureable impact on hydraulic conductivity. Hydraulic conductivity of both GCLs decreased by a factor of approximately 1.5–1.8 during permeation with CsCl in response to osmotic swelling induced by the low ionic strength of the CsCl solution entering the pore space. In contrast, permeation with the NaOH–CsCl solution caused the hydraulic conductivity of both GCLs to increase modestly (<50 times the hydraulic conductivity to DI water), and then level out (or decrease slightly) as a result of reduced osmotic swelling in the interlayer combined with dissolution of the mineral. For the tests conducted with CsCl solution, nearly all of the Cs was adsorbed by the bentonite. In contrast, Cs broke through readily when the NaOH–CsCl solution was used as the permeant solution. Permeation with the NaOH–CsCl solution also increased the sodicity of the bentonite by replacing bound K, Ca, and Mg on the mineral surface.     

Laboratory investigation of GCL hydration from Lateritic subsoils

A laboratory investigation on the hydration behavior of GCLs from lateritic soils was conducted under isothermal and thermal conditions (tropical climate), varying subsoil moisture contents, GCLs bentonite particle size and mineralogy. GCL hydration levels from lateritic subsoils under isothermal conditions (55%) were similar to literature findings. A slight decrease in water content of some GCLs after long periods of contact with the lateritic soils indicates that equilibrium can demand long time in these soils. GCL with granular bentonites were less efficient to hydrate from lateritic subsoils. GCLs with activated-calcium bentonites maintained hydration levels in long-term. Nonwoven geotextile facing down favored capillary effects. Thermal cycles significantly influenced GCLs hydration from subsoils. Capillary connections developed during hydration under isothermal conditions due to suction gradient reductions. Post-hydration tests under isothermal conditions showed more alterations in GCLs swelling and cation exchange properties than thermal cycles test. An increase in the saturated hydraulic conductivity of GCLs was observed in both lateritic soils, mainly for isothermal condition, although continued attending hydraulic conductivity requirements for barrier applications.     

赤泥渗滤液对改性GCL防渗性能的影响

旨在评价商用土工合成材料黏土衬垫(GCL)用于阻隔赤泥渗滤液的有效性.赤泥渗滤液作用下GCL的防渗特性是评价其防污性能的关键因素.以商用改性GCL中膨润土为研究对象,通过自由膨胀试验,研究了4种赤泥渗滤液中膨润土的自由膨胀指数.以商用改性GCL为研究对象,通过改进滤失试验,研究了4种赤泥渗滤液作为渗透液作用下GCL渗透...     

竖向应力作用下GCL的膨胀特性和渗透性能

近年来,土工织物膨润土垫(GCL)被越来越多地应用到各种防渗工程之中,它的防渗有效性也成为了设计人员和研究人员所关注的焦点。GCL的防渗有效性包括渗透性能、吸附能力和内部剪切强度三个方面。通过水化膨胀试验和渗透试验研究了GCL在竖向应力作用下的膨胀特性和渗透性能,并分析了正应力和加压水化顺序的影响。试验结果表明:(1)随着竖向应力的增大,GCL的膨胀量不断减小,而GCL的渗透系数则出现先减小后略有增大的规律;(2)水化加压顺序对GCL的膨胀量和渗透系数均有影响;(3)在实际工程应用中,GCL铺设完成后在堆载之前最好完全水化,这样能够大大提高GCL的防渗有效性。     

Membrane behavior of bentonite-amended compacted clay

The performance of landfill liners can be enhanced if they exhibit a semipermeable membrane behavior, which restricts the migration of contaminants. Consequently, enhancing the membrane property of clays used for liners is becoming increasingly important. As bentonite has already proven to be an excellent additive for improving the membrane behavior of clay, the hydraulic conductivities and membrane behaviors of a locally available clay, known as Fukakusa clay, amended with different amounts of dry bentonite (5%, 10%, 15%, and 20%) were herein evaluated. The chemico-osmotic efficiency coefficient, ω, was obtained under different concentration differences of KCl solution (0.5, 1, 5, 10, and 50 mM) for specimens in rigid-wall cells. The test results show that the ω of unamended clay is very low and can be ignored unless amended with bentonite, and that hydraulic conductivity k is suitably low (1.58×10⁻⁹ m/s). Additionally, ω decreased as the KCl concentration increased, which is consistent with the theory that increasing concentration causes progressively greater shrinkage of the diffuse-double layers of the clay particles. Furthermore, the mechanisms that influence the membrane behavior are discussed from the viewpoints of the diffuse-double layer and the interparticle pore size with the assistance of SEM.