Mechanisms and products of surface-mediated reductive dehalogenation of carbon tetrachloride by Fe(II) on goethite

Natural attenuation processes of chlorinated solvents in soils and groundwaters are increasingly considered as options to manage contaminated sites. Under anoxic conditions, reactions with ferrous iron sorbed at iron(hyro)xides may dominate the overall transformation of carbon tetrachloride (CCl4) and other chlorinated aliphatic hydrocarbons. We investigated mechanisms and product formation of CCl4 reduction by Fe(II) sorbed to goethite, which may lead to completely dehalogenated products or to chloroform (CHCl3), a toxic product which is fairly persistent under anoxic conditions. A simultaneous transfer of two electrons and cleavage of two C-Cl bonds of CCl4 would completely circumvent chloroform production. To distinguish between initial one- or two-bond cleavage, 13C-isotope fractionation of CCl4 was studied for reactions with Fe(II)/ goethite (isotopic enrichment factor epsilon = -26.5% percent per thousand) and with model systems for one C-Cl bond cleavage and either single-electron transfer (Fe(II) porphyrin, epsilon = -26.1 percent per thousand) or partial two-electron transfer (polysulfide, epsilon = -22.2 percent per thousand). These epsilon values differ significantlyfrom calculations for simultaneous cleavage of two C-Cl bonds (epsilon approximately equal to -50 percent per thousand), indicating that only one C-Cl bond is broken in the critical first step of the reaction. At pH 7, reduction of CCl4 by Fe(II)/ goethite produced approximately 33% CHCl3, 20% carbon monoxide (CO), and up to 40% formate (HCOO-). Addition of 2-propanol-d8 resulted in 33% CDCl3 and only 4% CO, indicating that both products were generated from trichloromethyl radicals (*CCl3), chloroform by reaction with hydrogen radical donors and CO by an alternative pathway likely to involve surface-bound intermediates. Hydrolysis of CO to HCOO-was surface-catalyzed by goethite butwastoo slow to account for the measured formate concentrations. Chloroform yields slightly increased with pH at constant Fe(II) sorption density, suggesting that pH-dependent surface processes direct product branching ratios. Surface-stabilized intermediates may thus facilitate abiotic mineralization of CCl4, whereas the presence of H radical donors, such as natural organic matter, enhances formation of toxic CHCl3.     

Reductive dechlorination of carbon tetrachloride in aqueous solutions containing ferrous and copper ions

Fe(II) associated with iron-containing minerals has been shown to be a potential reductant in natural subsurface environments. While it is known that the surface-bound iron species has the capacity to dechlorinate various chlorinated compounds, the role of transition metals to act as catalysts with these iron species is of importance. We previously observed that the reduction of Cu(II) by Fe(II) associated with goethite enhanced the dechlorination efficiency of chlorinated compound. In this study, the reductive dechlorination of carbon tetrachloride (CCl4) by dissolved Fe(II) in the presence of Cu(II) ions was investigated to understand the synergistic effect of Fe(II) and Cu(II) on the dechlorination processes in homogeneous aqueous solutions. The dechlorination efficiency of CCl4 by Fe(II) increased with increasing Cu(II) concentrations over the range of 0.2-0.5 mM and then decreased at high Cu(II) concentrations. The efficiency and rate of CCl4 dechlorination also increased with increasing dissolved Fe(II) concentration in the presence of 0.5 mM Cu(II) at neutral pH. When the Fe(II)/Cu(II) ratio varied between 1 and 10, the pseudo-first-order rate constant (k(obs)) increased 250-fold from 0.007 h(-1) at 0.5 mM Fe(II) to 1.754 h(-1) at 5 mM Fe(II). X-ray powder diffraction and scanning electron microscopy analyses showed that Cu(II) can react with Fe(II) to produce different morphologies of ferric oxides and subsequently accelerate the dechlorination rate of CCl4 at a high Fe(II) concentration. Amorphous ferrihydrite was observed when the stoichiometric Fe(II)/Cu(II) ratio was 1, while green rust, goethite, and magnetite were formed when the molar ratios of Fe(II)/Cu(II) reached 4-6. In addition, the dechlorination of CCl4 by dissolved Fe(II) is pH dependent. CCl4 can be dechlorinated by Fe(II) over a wide range of pH values in the Cu(II)-amended solutions, and the k(obs) increased from 0.0057 h(-1) at pH 4.3 to 0.856 h(-1) at pH 8.5, which was 9-25 times greater than that in the absence of Cu(II) at pH 7-8.5. The high reactivity of dissolved Fe(II) on the dechlorination of CCl4 in the presence of Cu(II) under anoxic conditions may enhance our understanding of the role of Fe(II) and the long-term reactivity of the zerovalent iron system in the dechlorination processes for chlorinated organic contaminants.     

Influence of electrostatics on the oxidation rates of organic compounds in heterogeneous Fenton systems

Electrostatic effects influence the oxidation rates of charged dissolved organic compounds in systems where the hydroxyl radical (*OH) is produced by the iron oxide-catalyzed decomposition of hydrogen peroxide (H2O2). Experiments were performed using goethite and the *OH probes 14C-labeled formic acid, 2-chlorophenol (2-CP), and nitrobenzene. At pH 4 and an ionic strength of 0.01 M, formic acid (pKa = 3.745) detected a steady-state concentration of *OH ([*OH]ss, calculated as a solution average) approximately 50 times higher than the two neutral probes did in the same systems, indicating significant enrichment of formate at the surface of the positively charged iron oxide where the *OH is being produced. Increasing the pH and ionic strength decreased formic acid oxidation rates by factors consistent with predicted decreases in electrostatic effects. In the presence of high 2-CP concentrations, the [*OH]ss measured by formic acid decreased with time, and goethite coagulation increased, due to loss of positive charge on the oxide surface as the oxidation products of 2-CP complexed surface Fe species. The [*OH]ss detected by 2-CP did not change significantly, indicating that neither goethite coagulation nor surface complexation of 2-CP oxidation products interfered with the rate of *OH generation; however, such an effect could have occurred in experiments using dissolved Fe instead of goethite. Model predictions of organic compound oxidation rates in mineral-catalyzed Fenton-like systems were improved by taking electrostatic effects into account.     

Sorption of Sb(III) and Sb(V) to goethite: influence on Sb(III) oxidation and mobilization

Antimony is an element of growing interest for a variety of industrial applications, even though Sb compounds are classified as priority pollutants by the Environmental Protection Agency of the United States. Iron (Fe) hydroxides appear to be important sorbents for Sb in soils and sediments, but mineral surfaces can also catalyze oxidation processes and may thus mobilize Sb. The aim of this study was to investigate whether goethite immobilizes Sb by sorption or whether Sb(III) adsorbed on goethite is oxidized and then released. The sorption of both Sb(III) and Sb(V) on goethite was studied in 0.01 and 0.1 M KClO4 M solutions as a function of pH and Sb concentration. To monitor oxidation processes Sb species were measured in solution and in the solid phase. The results show that both Sb(III) and Sb(V) form inner-sphere surface complexes at the goethite surface. Antimony(III) strongly adsorbs on goethite over a wide pH range (3-12), whereas maximum Sb(V) adsorption is found below pH 7. At higher ionic strength, the desorption of Sb(V) is shifted to lower pH values, most likely due to the formation of ion pairs KSb(OH)6 degrees. The sorption data of Sb(V) can be fitted by the modified triple-layer surface complexation model. Within 7 days, Sb(III) adsorbed on goethite is partly oxidized at pH 3, 5.9 and 9.7. The weak pH-dependence of the rate coefficients suggests that adsorbed Sb(III) is oxidized by 02 and that the coordination of Sb(III) to the surface increases the electron density of the Sb atom, which enhances the oxidation process. At pH values below pH 7, the oxidation of Sb(III) did not mobilize Sb within 35 days, while 30% of adsorbed Sb(III) was released into the solution at pH 9.9 within the same time. The adsorption of Sb(III) on Fe hydroxides over a wide pH range may be a major pathway for the oxidation and release of Sb(V).     

Heterogeneous oxidation of Fe(II) on ferric oxide at neutral pH and a low partial pressure of O2

The objective of this study was to identify the rate and mechanism of abiotic oxidation of ferrous iron at the water-ferric oxide interface (heterogeneous oxidation) at neutral pH. Oxidation was conducted at a low partial pressure of O2 to slow the reactions and to represent very low dissolved oxygen (DO) conditions that can occur at oxic/anoxic fronts. Hydrous ferric oxide (HFO) was partially converted to goethite after 24 h of anoxic contact with Fe(II), consistent with previous results. This resulted in a significant decrease in sorption of Fe(II). No conversion to goethite was observed after 25 min of anoxic contact between HFO and Fe(II). O2 was then introduced into the chamber and sparged (transfer half-time of 1.6 min) into the previously anoxic suspension, and the rate of oxidation of Fe(II) and the distribution between sorbed and dissolved Fe(II) were measured with time. The concentration of sorbed Fe(II) remained steady during each experiment, despite removal of all measurable dissolved Fe(II) in some experiments. The rate of oxidation of Fe(II) was proportional to the concentration of DO and both sorbed and dissolved Fe(II) up to a surface density of 0.02 mol Fe(II) per mol Fe(III), i.e., approximately 0.2 Fe(II) per nm2 of ferric oxide surface area. This result differs from previous studies of heterogeneous oxidation, which found that the rate was proportional to sorbed Fe(II) and DO but did not find a dependence on dissolved Fe(II). Most previous experiments were autocatalytic; i.e., the initial concentration of ferric oxide was low or none, and sorbed Fe(II) was not measured. The results were consistentwith an anode/cathode mechanism, with O2 reduced at electron-deficient sites with strongly sorbed Fe(II) and Fe(II) oxidized at electron-rich sites without sorbed Fe(II). The pseudo-first-order rate constants for oxidation of dissolved Fe(II) were about 10 times faster than those previously predicted for heterogeneous oxidation of Fe(II).     

Effect of aqueous Fe(II) on arsenate sorption on goethite and hematite

Biogeochemical iron cycling often generates systems where aqueous Fe(II) and solid Fe(III) oxides coexist. Reactions between these species result in iron oxide surface and phase transformations, iron isotope fractionation, and redox transformations of many contaminant species. Fe(II)-induced recrystallization of goethite and hematite has recently been shown to cause the repartitioning of Ni(II) at the mineral-water interface, with adsorbed Ni incorporating into the iron oxide structure and preincorporated Ni released back into aqueous solution. However, the effect of Fe(II) on the fate and speciation of redox inactive species incompatible with iron oxide structures is unclear. Arsenate sorption to hematite and goethite in the presence of aqueous Fe(II) was studied to determine whether Fe(II) causes substantial changes in the sorption mechanisms of such incompatible species. Sorption isotherms reveal that Fe(II) minimally alters macroscopic arsenate sorption behavior except at circumneutral pH in the presence of elevated concentrations (10?3 M) of Fe(II) and at high arsenate loadings, where a clear signature of precipitation is observed. Powder X-ray diffraction demonstrates that the ferrous arsenate mineral symplesite precipitates under such conditions. Extended X-ray absorption fine structure spectroscopy shows that outside this precipitation regime arsenate surface complexation mechanisms are unaffected by Fe(II). In addition, arsenate was found to suppress Fe(II) sorption through competitive adsorption processes before the onset of symplesite precipitation. This study demonstrates that the sorption of species incompatible with iron oxide structure is not substantially affected by Fe(II) but that such species may potentially interfere with Fe(II)-iron oxide reactions via competitive adsorption.     

Iron oxide surface-catalyzed oxidation of ferrous iron by monochloramine: implications of oxide type and carbonate on reactivity

The maintenance of monochloramine residuals in drinking water distribution systems is one technique often used to minimize microbial outbreaks and thereby maintain the safety of the water. Reactions between oxidizable species and monochloramine can however lead to undesirable losses in the disinfectant residual. Previous work has illustrated that the Fe(II) present within distribution systems is one type of oxidizable species that can exert a monochloramine demand. This paper extends this prior work by examining the kinetics of the reactions between Fe(II) and monochloramine in the presence of a variety of iron oxide surfaces. The identity of the iron oxide plays a significant role in the rate of these reactions. Surface area-normalized initial rate coefficients (k(init)) obtained in the presence of each oxide at pH approximately 6.9 exhibit the following trend in catalytic activity: magnetite > goethite > hematite approximately = lepidocrocite > ferrihydrite. The differences in the activity of these oxides are hypothesized to result from variations in the amount of Fe(II) sorbed to each of the oxides and to dissimilarities in the surface site densities of the oxides. The implications of carbonate on Fe(II) sorption to iron oxides are also examined. Comparing Fe(II) sorption isotherms for goethite obtained under differential carbonate concentrations, it is apparent that as the carbonate concentration (C(T,CO3)) increased from 0 to 11.7 mM that the Fe(II) sorption edge (50% sorption) shifts from a pH of approximately 5.8 to a pH of 7.8. This shift is hypothesized to be the result of the formation of aqueous and surface carbonate-Fe(II) complexes and to competition between carbonate and Fe(II) for surface sites. The implications of these changes are then discussed in light of the variable oxide studies.     

Formation of metal-arsenate precipitates at the goethite-water interface

Little information is available concerning cosorbing oxyanion and metal contaminants in the environment, yet in most metal-contaminated areas, cocontamination by arsenate [AsO4, As(V)] is common. This study investigated the cosorption of As(V) and Zn on goethite at pH 4 and 7 as a function of final solution concentration. Complimentary extended X-ray absorption fine structure (EXAFS) spectroscopic data were collected at the As and Zn K-edges in order to glean information about the coordination environment of As and Zn at the goethite-water interface. Macroscopic sorption studies revealed that As(V) and Zn sorption on goethite increased in cosorption experiments beyond that suggested by single sorption isotherms. At pH 4 and 7, As(V) surface saturation was 3.2 and 2.2 micromol m(-2), respectively, and Zn surface saturation was absent at pH 4 and approximately 1.0 micromol m(-2) at pH 7. Arsenate sorption on goethite increased in the presence of Zn by 29% and by more than 500% at pH 4 and 7, respectively. In the presence of As(V), Zn sorption on goethite increased by 800 and 1300% at pH 4 and 7, respectively. More As(V) than Zn sorbed on goethite below surface saturation at pH 7. Above surface saturation, the Zn:As surface density ratio (SDR) remained constant at 0.91 +/- 0.03. At pH 4, the Zn:As SDR was less than 1 throughout the concentration range. Below As(V) surface saturation on goethite, As(V) formed bidentate binuclear bridging complexes on Fe and/or Zn octahedra, while Zn mainly formed edge-sharing complexes with Fe at the goethite surface. Above surface saturation, Zn was increasingly complexed by AsO4, gradually forming an adamite-like [Zn2(AsO4)OH] surface precipitate on goethite. Precipitated contaminants are more stable due to the limited dissolution kinetics of their solid phase. This study may therefore prove useful in remediation strategies of sites knowingly contaminated with oxyanions and metals.     

Synergistic effect of copper ion on the reductive dechlorination of carbon tetrachloride by surface-bound Fe(II) associated with goethite

The dechlorination of carbon tetrachloride (CT) by Fe(II) associated with goethite in the presence of transition metal ions was investigated. X-ray photoelectron spectroscopy (XPS) and X-ray powder diffraction (XRPD) were used to characterize the chemical states and crystal phases of transition metals on solid phases, respectively. CT was dechlorinated to chloroform (CF) by 3 mM Fe(II) in 10 mM goethite (25.6 m2 L(-1)) suspensions. The dechlorination followed pseudo-first-order kinetics, and a rate constant (k(obs)) of 0.036 h(-1) was observed. Transition metal ions have different effects on CT dechlorination. The addition of Ni(II), Co(II), and Zn(II) lowered the k(obs) for CT dechlorination, whereas the amendment of 0.5 mM Cu(II) into the Fe(II)-Fe(III) system significantly enhanced the efficiency and the rate of CT dechlorination. The k(obs) for CT dechlorination with 0.5 mM Cu(II) was 1.175 h(-1), which was 33 times greater than that without Cu(II). Also, the dechlorination of CT by surface-bound iron species is pH-dependent, and the rate constants increased from 0.008 h(-1) at pH 4.0 to 1.175 h(-1) at pH 7.0. When the solution contained Cu(II) and Fe(II) without goethite, a reddish-yellow precipitate was formed, and the concentration of Fe(ll) decreased with the increase in Cu(II) concentration. XPS and XRPD analyses suggested the possible presence of Cu2O and ferrihydrite in the precipitate. Small amounts of aqueous Cu(I) were also detected, reflecting the fact that Cu(II) was reduced to Cu(I) by Fe(II). A linear relationship between k(obs) for CT dechlorination and the concentration of Cu(II) was observed when the amended Cu(II) concentration was lower than 0.5 mM. Moreover, the k(obs) for CT dechlorination was dependent on the Fe(II) concentration in the 0.5 mM Cu(II)-amended goethite system and followed a Langmuir-Hinshelwood relationship. These results clearly indicate that Fe(II) serves as the bulk reductant to reduce both CT and Cu(II). The resulting Cull) can further act as a catalyst to enhance the dechlorination rate of chlorinated hydrocarbons in iron-reducing environments.     

Degradation of drinking water disinfection byproducts by synthetic goethite and magnetite

Corrosion of iron pipes leads to the release of ferrous iron, Fe(II), and the formation of iron oxides, such as goethite and magnetite, on the pipe surface. Fe(II), a potent reductant when associated with iron oxide surfaces, can mediate the reduction of halogenated organic compounds. Batch experiments were performed to investigate the kinetics and pathways of the degradation of selected chlorinated disinfection byproducts (OBPs) by Fe(II) in the presence of synthetic goethite and magnetite. Trichloronitromethane was degraded via reduction, while trichloroacetonitrile, 1,1,1-trichloropropanone, and trichloroacetaldyde hydrate were transformed via both hydrolysis and reduction. Chloroform and trichloroacetic acid were unreactive. Observed pseudo-first-order reductive dehalogenation rates were influenced by DBP chemical structure and identity of the reductant. Fe(II) bound to iron minerals had greater reactivity than either aqueous Fe(II) or structural Fe(II) present in magnetite. For DBPs of structure Cl3C-R, reductive dehalogenation rate constants normalized by the surface density of Fe(II) on both goethite and magnetite correlated with the electronegativity of the -R group and with one electron reduction potential. In addition to chemical transformation, sorption onto the iron oxide minerals was also an important loss process for 1,1,1-trichloropropanone.     

XANES investigation of phosphate sorption in single and binary systems of iron and aluminum oxide minerals

Phosphate sorption on Fe- and Al-oxide minerals helps regulate the solubility and mobility of P in the environment. The objective of this study was to characterize phosphate adsorption and precipitation in single and binary systems of Fe- and Al-oxide minerals. Varying concentrations of phosphate were reacted for 42 h in aqueous suspensions containing goethite, ferrihydrite, boehmite, or noncrystalline (non-xl) Al-hydroxide, and in 1:1 (by mass) mixed-mineral suspensions of goethite/boehmite and ferrihydrite/ non-xl Al-hydroxide at pH 6 and 22 degrees C. X-ray absorption near edge structure (XANES) spectroscopy was used to detect precipitated phosphate and distinguish PO4 associated with Fe(III) versus Al(III) in mixed-mineral systems. Changes in the full width at half-maximum height (fwhm) in the white-line peak in P K-XANES spectra provided evidence for precipitation in Al-oxide single-mineral systems, but not in goethite or ferrihydrite systems. Similarly, adsorption isotherms and XANES data showed evidence for precipitation in goethite/boehmite mixtures, suggesting that mineral interactive effects on PO4 sorption were minimal. However, sorption in ferrihydrite/non-xl Al-hydroxide systems and a lack of XANES evidence for precipitation indicated that mineral interactions inhibited precipitation in these binary mixtures.     

Reduction of polyhalogenated methanes by surface-bound Fe(II) in aqueous suspensions of iron oxides

Uptake of ferrous iron from aqueous solution by iron oxides results in the formation of a variety of reactive surface species capable of reducing polyhalogenated methanes (PHMs). Pseudo-first-order reaction rate constants, k(obs), of PHMs increased in the order CHBrCl2 < CHBr2Cl < CHBr3 < CCl4 < CFBr3 < CBrCl3 < CBr2Cl2. The k(obs) values increased with the exposure time, teq, of Fe(II) to suspended iron oxides which was attributed to the rearrangement of initially sorbed Fe(II) species to more reactive surface species with time. At pH 7.2, the k(obs) values of PHMs also increased with the concentration of surface-bound ferrous iron, Fe(II)sorb, particularly when Fe(II)tot was increased to concentrations where surface precipitation becomes likely. At fixed total Fe(II) concentrations, k(obs) values increased exponentially with pH. The highest reactivities were associated with pH conditions where surface precipitation of Fe(II) is expected. Fe(II)sorb and pH, however, had opposite effects on the product formation of PHMs. At pH 7.2, the formation of formate from CX4 (X = CI, Br) increased with Fe(II)sorb, whereas increasing pH favored the formation of CHX3. The ratio of halogenated products and formate formed is indicative of the relative importance of initial one- or two-electron-transfer processes, respectively, and was found to depend on the type of iron oxide mineral also. Our data form a basis to assess the importance of chemical reactions in natural attenuation processes of PHMs in environmental systems under iron-reducing conditions.     

Reactivity of Fe(II)-bearing minerals toward reductive transformation of organic contaminants

Fe(II) present at surfaces of iron-containing minerals can play a significant role in the overall attenuation of reducible contaminants in the subsurface. As the chemical environment, i.e., the type and arrangement of ligands, strongly affects the redox potential of Fe(II), the presence of various mineral sorbents is expected to modulate the reactivity of surficial Fe(II)-species in aqueous systems. In a comparative study we evaluated the reactivity of ferrous iron in aqueous suspensions of siderite (FeCO3), nontronite (ferruginous smectite SWa-1), hematite (alpha-Fe2O3), lepidocrocite (gamma-FeOOH), goethite (alpha-FeOOH), magnetite (Fe3O4), sulfate green rust (Fe(II)4Fe(III)2(OH)12SO4 x 4H2O), pyrite (FeS2), and mackinawite (FeS) under similar conditions (pH 7.2, 25 m2 mineral/L, 1 mM Fe(II)aq, O2 (aq) < 0.1 g/L). Surface-area-normalized pseudo first-order rate constants are reported for the reduction of hexachloroethane and 4-chloronitrobenzene representing two classes of environmentally relevant transformation reactions of pollutants, i.e., dehalogenation and nitroaryl reduction. The reactivities of the different Fe(II) mineral systems varied greatly and systematically both within and between the two data sets obtained with the two probe compounds. As a general trend, surface-area-normalized reaction rates increased in the order Fe(II) + siderite < Fe(II) + iron oxides < Fe(II) + iron sulfides. 4-Chloronitrobenzene was transformed by mineral-bound Fe(II) much more rapidly than hexachloroethane, except for suspensions of hematite, pyrite, and nontronite. The results demonstrate that abiotic reactions with surface-bound Fe(II) may affect or even dominate the long-term behavior of reducible pollutants in the subsurface, particularly in the presence of Fe(III) bearing minerals. As such reactions can be dominated by specific interactions of the oxidant with the surface, care must be taken in extrapolating reactivity data of surface-bound Fe(II) between different compound classes.     

Microbially catalyzed nitrate-dependent oxidation of biogenic solid-phase Fe(II) compounds

The potential for microbially catalyzed NO3(-)-dependent oxidation of solid-phase Fe(II) compounds was examined using a previously described autotrophic, denitrifying, Fe(II)-oxidizing enrichment culture. The following solid-phase Fe(II)-bearing minerals were considered: microbially reduced synthetic goethite, two different end products of microbially hydrous ferric oxide (HFO) reduction (biogenic Fe3O4 and biogenic FeCO3), chemically precipitated FeCO3, and two microbially reduced iron(III) oxide-rich subsoils. The microbially reduced goethite, subsoils, and chemically precipitated FeCO3 were subject to rapid NO3(-)-dependent Fe(II) oxidation. Significant oxidation of biogenic Fe3O4 was observed. Very little biogenic FeCO3 was oxidized. No reduction of NO3- or oxidation of Fe(II) occurred in pasteurized cultures. The molar ratio of NO3- reduced to Fe(II) oxidized in cultures containing chemically precipitated FeCO3, and one of the microbially reduced subsoils approximated the theoretical stoichiometry of 0.2:1. However, molar ratios obtained for oxidation of microbially reduced goethite, the other subsoil, and the HFO reduction end products did not agree with this theoretical value. These discrepancies may be related to heterotrophic NO3- reduction coupled to oxidation of dead Fe(III)-reducing bacterial biomass. Our findings demonstrate that microbally catalyzed NO3(-)-dependent Fe(II) oxidation has the potential to significantly accelerate the oxidation of solid-phase Fe(II) compounds by oxidized N species. This process could have an important influence on the migration of contaminant metals and radionuclides in subsurface environments.     

Factors affecting the yield of oxidants from the reaction of nanoparticulate zero-valent iron and oxygen

The corrosion of zero-valent iron (Fe0(s)) by oxygen (O2) can lead to the oxidation of organic compounds. To gain insight into the reaction mechanism and to assess the nature of the oxidant, the oxidation of methanol, ethanol, 2-propanol, and benzoic acid by the reaction of nanoparticulate zero-valent iron (nZVI) or ferrous iron (Fe[II]) with O2 in the absence of ligands was studied. At pH values below 5, Fe0(s) nanoparticles were oxidized by O2 within 30 min with a stoichiometry of approximately two Fe0(s) oxidized per O2 consumed. The yield of methanol and ethanol oxidation products increased from 1% at acidic pH to 6% at pH 7, relative to nZVI added. Product yields from 2-propanol and benzoic acid were highest under acidic conditions, with little oxidation observed at neutral pH. At pH values below 5, product formation was attributable to hydroxyl radical (OH.) production through the Fenton reaction, involving hydrogen peroxide and Fe(II) produced during nZVI oxidation. At higher pH values, the oxidation of Fe(II), the initial product of nZVI oxidation, by oxygen is responsible for most of the oxidant production. Product yields at circumneutral pH values were consistent with a different oxidant, such as the ferryl ion (Fe[IV]).     

Comparison of arsenic(V) and arsenic(III) sorption onto iron oxide minerals: implications for arsenic mobility

Arsenic derived from natural sources occurs in groundwater in many countries, affecting the health of millions of people. The combined effects of As(V) reduction and diagenesis of iron oxide minerals on arsenic mobility are investigated in this study by comparing As(V) and As(III) sorption onto amorphous iron oxide (HFO), goethite, and magnetite at varying solution compositions. Experimental data are modeled with a diffuse double layer surface complexation model, and the extracted model parameters are used to examine the consistency of our results with those previously reported. Sorption of As(V) onto HFO and goethite is more favorable than that of As(III) below pH 5-6, whereas, above pH 7-8, As(II) has a higher affinity for the solids. The pH at which As(V) and As(III) are equally sorbed depends on the solid-to-solution ratio and type and specific surface area of the minerals and is shifted to lower pH values in the presence of phosphate, which competes for sorption sites. The sorption data indicate that, under most of the chemical conditions investigated in this study, reduction of As(V) in the presence of HFO or goethite would have only minor effects on or even decrease its mobility in the environment at near-neutral pH conditions. As(V) and As(III) sorption isotherms indicate similar surface site densities on the three oxides. Intrinsic surface complexation constants for As(V) are higher for goethite than HFO, whereas As(III) binding is similar for both of these oxides and also for magnetite. However, decrease in specific surface area and hence sorption site density that accompanies transformation of amorphous iron oxides to more crystalline phases could increase arsenic mobility.     

Solution speciation controls mercury isotope fractionation of Hg(II) sorption to goethite

The application of Hg isotope signatures as tracers for environmental Hg cycling requires the determination of isotope fractionation factors and mechanisms for individual processes. Here, we investigated Hg isotope fractionation of Hg(II) sorption to goethite in batch systems under different experimental conditions. We observed a mass-dependent enrichment of light Hg isotopes on the goethite surface relative to dissolved Hg (ε(202)Hg of -0.30‰ to -0.44‰) which was independent of the pH, chloride and sulfate concentration, type of surface complex, and equilibration time. Based on previous theoretical equilibrium fractionation factors, we propose that Hg isotope fractionation of Hg(II) sorption to goethite is controlled by an equilibrium isotope effect between Hg(II) solution species, expressed on the mineral surface by the adsorption of the cationic solution species. In contrast, the formation of outer-sphere complexes and subsequent conformation changes to different inner-sphere complexes appeared to have insignificant effects on the observed isotope fractionation. Our findings emphasize the importance of solution speciation in metal isotope sorption studies and suggest that the dissolved Hg(II) pool in soils and sediments, which is the most mobile and bioavailable, should be isotopically heavy, as light Hg isotopes are preferentially sequestered during binding to both mineral phases and natural organic matter.     

Competing Fe (II)-induced mineralization pathways of ferrihydrite

Owing to its high surface area and intrinsic reactivity, ferrihydrite serves as a dominant sink for numerous metals and nutrients in surface environments and is a potentially important terminal electron acceptor for microbial respiration. Introduction of Fe (II), by reductive dissolution of Fe(III) minerals, for example, converts ferrihydrite to Fe phases varying in their retention and reducing capacity. While Fe(II) concentration is the master variable dictating secondary mineralization pathways of ferrihydrite, here we reveal thatthe kinetics of conversion and ultimate mineral assemblage are a function of competing mineralization pathways influenced by pH and stabilizing ligands. Reaction of Fe(II) with ferrihydrite results in the precipitation of goethite, lepidocrocite, and magnetite. The three phases vary in their precipitation extent, rate, and residence time, all of which are primarily a function of Fe(II) concentration and ligand type (Cl, SO4, CO3). While lepidocrocite and goethite precipitate over a large Fe(II) concentration range, magnetite accumulation is only observed at surface loadings greater than 1.0 mmol Fe(II)/g ferrihydrite (in the absence of bicarbonate). Precipitation of magnetite induces the dissolution of lepidocrocite (presence of Cl) or goethite (presence of SO4), allowing for Fe(III)-dependent crystal growth. The rate of magnetite precipitation is a function of the relative proportions of goethite to lepidocrocite; the lower solubility of the former Fe (hydr)oxide slows magnetite precipitation. A one unit pH deviation from 7, however, either impedes (pH 6) or enhances (pH 8) magnetite precipitation. In the absence of magnetite nucleation, lepidocrocite and goethite continue to precipitate at the expense of ferrihydrite with near complete conversion within hours, the relative proportions of the two hydroxides dependent upon the ligand present. Goethite also continues to precipitate at the expense of lepidocrocite in the absence of chloride. In fact, the rate and extent of both goethite and magnetite precipitation are influenced by conditions conducive to the production and stability of lepidocrocite. Thus, predicting the secondary mineralization of ferrihydrite, a process having sweeping influences on contaminant/nutrient dynamics, will need to take into consideration kinetic restraints and transient precursor phases (e.g., lepidocrocite) that influence ensuing reaction pathways.     

Potential function of added minerals as nucleation sites and effect of humic substances on mineral formation by the nitrate-reducing Fe(II)-oxidizer Acidovorax sp. BoFeN1

The mobility of toxic metals and the transformation of organic pollutants in the environment are influenced and in many cases even controlled by iron minerals. Therefore knowing the factors influencing iron mineral formation and transformation by Fe(II)-oxidizing and Fe(III)-reducing bacteria is crucial for understanding the fate of contaminants and for the development of remediation technologies. In this study we followed mineral formation by the nitrate-reducing Fe(II)-oxidizing strain Acidovorax sp. BoFeN1 in the presence of the crystalline Fe(III) (oxyhydr)oxides goethite, magnetite and hematite added as potential nucleation sites. M?ssbauer spectroscopy analysis of minerals precipitated by BoFeN1 in (57)Fe(II)-spiked microbial growth medium showed that goethite was formed in the absence of mineral additions as well as in the presence of goethite or hematite. The presence of magnetite minerals during Fe(II) oxidation induced the formation of magnetite in addition to goethite, while the addition of humic substances along with magnetite also led to goethite but no magnetite. This study showed that mineral formation not only depends on the aqueous geochemical conditions but can also be affected by the presence of mineral nucleation sites that initiate precipitation of the same underlying mineral phases.     

Coupled Fe(II)-Fe(III) electron and atom exchange as a mechanism for Fe isotope fractionation during dissimilatory iron oxide reduction

Microbial dissimilatory iron reduction (DIR) is an important pathway for carbon oxidation in anoxic sediments, and iron isotopes may distinguish between iron produced by DIR and other sources of aqueous Fe(II). Previous studies have shown that aqueous Fe(II) produced during the earliest stages of DIR has delta56Fe values that are 0.5-2.0%o lowerthan the initial Fe(III) substrate. The new experiments reported here suggest that this fractionation is controlled by coupled electron and Fe atom exchange between Fe(II) and Fe(III) at iron oxide surfaces. In hematite and goethite reduction experiments with Geobacter sulfurreducens, the 56Fe/54Fe isotopic fractionation between aqueous Fe(II) and the outermost layers of Fe(III) on the oxide surface is approximately -3%o and can be explained by equilibrium Fe isotope partitioning between reactive Fe(II) and Fe(III) pools that coexist during DIR. The results indicate that sorption of Fe(II) to Fe(III) substrates cannot account for production of low-delta56Fe values for aqueous Fe(II) during DIR.