黄铜应力腐蚀敏感性及其与脱Zn层拉应力的对应性

测量了不同极化电位下,Ｈ６２黄铜在氨水溶液腐蚀过程中表面脱Ｚｎ蔬松层引起的拉应力,并用单边缺口试样测量的不同极化电位下的应力腐蚀敏感性,结果表明：黄铜在氨水中自然腐蚀时,在脱Ｚｎ层界面会产生 大的拉应力,整个试样的平均应力为σ＝１８．１ＭＰａ;阳极极化使表面拉应力略有下降,阴极极化则使疏松层引起的拉应力急剧下降乃至为零,阴极极化在表层产生镀Ｃｕ层后出现尖力;应力腐蚀敏感性随外加电位的变化规律和疏松     

可计及温度与层状结构影响的超高温陶瓷基复合材料涂层残余热应力理论表征模型

目的创建可计及温度与层状结构共同影响的超高温陶瓷基复合材料涂层与基体层因热不匹配导致的残余热应力的理论表征模型。方法基于经典的层合板理论与超高温陶瓷基复合材料热物理性能参数对温度的敏感性研究,引入温度和层状结构对涂层与基体层所受残余热应力的影响,形成各层残余热应力温度相关性的理论表征方法,并以ZrB_2-SiC复合材料涂层为例,利用该理论方法系统地研究了各种控制机制对残余热应力的影响及其随温度的演化规律。结果超高温陶瓷基复合材料涂层与基体层所受的残余热应力随着温度的变化而变化,涂层热膨胀系数与基体层热膨胀系数差别越大,变化幅度越大。当涂层材料热膨胀系数大于基体层材料热膨胀系数时,涂层材料遭受残余拉应力,基体层材料遭受残余压应力;随着涂层厚度的增加,涂层所受拉应力减小,而基体层所受压应力增大;当涂层材料热膨胀系数小于基体层材料热膨胀系数时,涂层材料遭受残余压应力,基体层材料遭受残余拉应力;随着涂层厚度的增加,涂层所受压应力减小,而基体层所受拉应力增大。低温下,各层所受残余热应力对层厚与每层材料组成的变化比较敏感,随着温度的升高,敏感性降低。结论对于涂层材料,应设计涂层材料的热膨胀系数小于基体层材料的热膨胀系数,使涂层遭受残余压应力,这不仅能够降低材料表面产生裂纹的危险,同时可以抑制表面已有缺陷的扩展。同时应当设计相对较小的涂层厚度,以增大涂层所受的残余压应力,降低基体层所受的残余拉应力,有效提高整体材料在不同温度下的强度性能。     

Inconel 718合金锻造压气机盘件的残余应力及显微组织特征（英文）

残余应力对商用发动机Inconel 718材料构件的疲劳性能、可靠性与耐久性起着重要作用,但由于中国中子衍射测量设备与测量经验与标准的缺乏,压气机盘件的系统性残余应力研究鲜见报导。采用X射线与中子衍射分别测量Inconel 718锻造盘件的表面及内部残余应力,采用扫描电子显微镜与透射电子显微镜观察锻造显微组织特征。锻造盘件表面呈压残余应力,内部为拉残余应力,且相比于锻造产生的残余应力,盘件表面的残余应力受粗加工影响较大。位错密度随距盘件表面的距离减小而增高,残余应力会加速位错产生与动态再结晶。     

自蔓延反应喷涂锻造温度场和残余应力的数值模拟

采用ANSYS有限元软件对钢板表面反应预涂TiCNi涂层以及反应喷涂后锻造两种加工过程的温度场和残余应力场进行了模拟计算和比较,得到了各涂层基体喷涂锻造温度场规律.基体高温时喷涂锻造可以降低涂层试件的冷却速度,从而减缓裂纹的产生;研究了反应喷涂锻造对涂层残余应力的影响.结果表明:锻造后各层中的残余应力远小于锻造前各层中的残余应力,而提高始锻造温度可以减小涂层中残余应力.     

柴油发动机进气阀断裂分析

柴油发动机进气阀为一体式锻造、硬质合金堆焊而成,在使用过程中发生断裂。为了分析断裂原因和制定对策,对断裂进气阀的断口宏观特征、微观形貌、金相组织、化学成分、显微硬度和残余应力进行分析。结果表明：进气阀断裂模式为疲劳断裂;零件堆焊层中存在较高的硬度和残余拉应力;进气阀在复杂的工作环境中受到机械冲击负荷和高残余拉应力的叠加作用,加上高的脆性,导致堆焊区局部裂纹产生;在重复的工作负荷下,裂纹以疲劳方式进一步扩展,直至断裂。建议严格控制进气阀堆焊后的热处理工艺,降低硬度和残余拉应力,从而有效避免此类失效的发生。     

中厚板机器人横焊接头残余应力的有限元分析

依据热弹塑性理论,建立了中厚板机器人多层多道焊三维热力学有限元模型。利用ABAQUS有限元分析软件对中厚板机器人横焊接头残余应力场进行了模拟计算,并对其分布特征进行了分析。分析结果表明,接头表面的纵向残余应力在焊缝区域内表现为拉应力,在远离焊缝的母材区域内表现为压应力,且开坡口一侧母材区域的残余压应力值高于未开坡口侧;对于横向残余应力,接头表面表现为拉应力,且焊缝区域附近拉应力较高,焊趾处出现应力峰值。对于接头横截面,沿板厚方向上,焊缝区表现为拉应力;沿板宽方向上,近焊缝上下表面区均为拉应力,焊缝中心区域则表现为压应力。将模拟结果与盲孔法测试结果进行对比,两者较吻合。     

支承辊淬硬层条带状疲劳裂纹的扩展动力研究

支承辊淬硬层内部条带状疲劳裂纹的形成以及由此引起的大面积剥落是支承辊危害最大的失效形式之一。本文通过对淬硬层应力状态的计算分析得出径向残余拉应力是条带状疲劳裂纹主要扩展动力的结论,并进行了疲劳裂纹扩展实验验证。在保证使用性能前提下降低支承辊淬硬层残余应力水平有利于遏制条带状疲劳裂纹发展。     

高纯钛的反复弯曲疲劳

通过对不同应力幅度下高纯钛的反复弯曲疲劳的研究，发现在较低应力幅度下（～±１００ＭＰａ），材料表现出循环软化，伴随表面滑移带数量的增加、发达的滑移带挤出片的出现。疲劳裂纹萌生主要与滑移带相关，在挤出物内存在两类疲劳损伤形式：沿滑移带的孔洞和与滑移带垂直的微裂纹。在较高应力幅度下（～±２００ＭＰａ），则表现为硬化，次滑移及晶界附近多个滑移系同时起动，有大的形变孪晶出现。裂纹于滑移带、李晶界和晶界结点萌生。断口特征复杂，但与表面变形特征有对应关系。ＴＥＭ亚结构分析表明，随应力幅度的提高，位错组态分别为散乱分布于滑移面的偶极子、位错束带和位错胞。李晶内存在复杂的精细结构，而且有堆垛层错出现。     

激光辅助氮化工艺中的开裂行为研究

目的研究激光辅助氮化过程中,氮化层的开裂行为。方法利用CO2激光辅助氮化的方法在钛合金表面制备氮化钛涂层,观察氮化层的宏观、微观形貌,分析组织结构特征,测定氮化层残余应力,研究基体厚度、激光扫描工艺参数对氮化层表面形貌和裂纹情况的影响。结果钛合金经单道或多道激光氮化后,表面形成非均匀氮化钛层,其显微结构为沿主干轴交叉生长的枝状晶组织,存在数量和尺寸不等的显微裂纹。较薄试样经单道激光氮化后,表面呈现较低的残余压应力状态,较厚试样则以拉应力为主;试样经多道激光氮化后,整个氮化区表面均呈现残余压应力状态。结论枝状氮化层与基体组织高度结合,不易脱落,但受基体约束作用,氮化层内的拉伸热应力导致其冷却过程中形成微裂纹。随着试样厚度和氮化面积的增加,较高的热应力使得裂纹密度和裂纹尺寸增加,严重影响氮化层的质量。残余应力是热应力和相变应力叠加的结果,对于多道激光氮化工艺而言,大面积氮化使得相变压应力增加,同时后热效应使得热应力降低,最终呈现出残余压应力状态。     

预应力干磨削加工40Cr工件表面微结构损伤

表面残余应力、表面烧伤、磨削裂纹等表面微结构损伤是评价零件表面质量的重要指标,直接影响零件的使用寿命,严重时造成零件失效。为研究预应力干磨削加工零件表面微结构损伤特征及规律,以40Cr材料为载体,开展预应力磨削加工试验研究,检测残余应力、硬度,并采用SEM、EDS等方法分析表面层形貌和化学成分。结果表明,试件加工表面存在淬硬现象,预应力对工件表层残余应力有较好的抑制作用,表层残余拉应力随磨削深度增大而增大,随预应力增大而减小。磨削深度对熔融涂覆及表面微裂纹损伤影响程度较大,磨削烧伤表面形成氧化膜会影响零件使用性能。预拉应力通过改变残余应力状态而对表面磨削微裂纹损伤起到抑制作用。     

Effects of Post-weld Heat Treatment on Microstructure,Mechanical Properties and the Role of Weld Reinforcement in 2219 Aluminum Alloy TIG-Welded Joints

In as-welded state, each region of 2219 aluminum alloy TIG-welded joint shows diff erent microstructure and microhardness due to the diff erent welding heat cycles and the resulting evolution of second phases. After the post-weld heat treatment, both the amount and the size of the eutectic structure or θ phases decreased. Correspondingly, both the Cu content in α-Al matrix and the microhardness increased to a similar level in each region of the joint, and the tensile strength of the entire joint was greatly improved. Post-weld heat treatment played the role of solid solution strengthening and aging strengthening. After the post-weld heat treatment, the weld performance became similar to other regions, but weld reinforcements lost their reinforcing eff ect on the weld and their existence was more of an adverse eff ect. The joint without weld reinforcements after the post-weld heat treatment had the optimal tensile properties, and the specimens randomly crack in the weld zone.     

The First Phase of the SRIF Industrialized Base in ＂West Area＂ Has Been Put into Operation

After nearly two years＇ tense construction, the first phase of industrialized base of Shenyang Research Institute of Foundry （SRIF）, located at the Tiexi Casting and Forging Industrial Park in the west of Tiexi District, has now been completed and formally put into operation.     

Thermodynamics Study on the Decomposition of Chromite with KOH

Institute of Process Engineering, Chinese Academy of Sciences, China, has proposed a method for oxidative leaching of chromite with potassium hydroxide. Understanding the mechanism of chromite decomposition, especially in the potassium hydroxide fusion, is important for the optimization of the operating parameters of the oxidative leaching process. A traditional thermodynamic method is proposed and the thermal decomposition and the reaction decomposition during the oxidative leaching of chromite with KOH and oxygen is discussed, which suggests that chromite is mainly destroyed by reactions with KOH and oxygen. Meanwhile, equilibrium of the main reactions of the above process was calculated at different temperatures and oxygen partial pressures. The stable zones of productions, namely, K2CrO4 and Fe2O3, increase with the decrease of temperature, which indicates that higher temperature is not beneficial to thermodynamic reactions. In addition, a comparison of the general alkali methods is carried out, and it is concluded that the KOH leaching process is thermodynamically superior to the conventional chromate production process.     

Influence of Heat Treatment on Damping Behaviour of the Magnesium Wrought Alloy AZ61

The effect of isochronal heat treatments for 1h on variation of damping, hardness and microstructural change of the magnesium wrought alloy AZ61 was investigated. Damping and hardness behaviour could be attributed to the evolution of precipitation process. The influence of precipitation on damping behaviour was explained in the framework of the dislocation string model of Granato and Lücke.     

Effect of Rare Earth Doping on Impedance,Modulus and Conductivity Properties of Multiferroic Composites:0.5(BiLa_xFe_(1-x)O_3)–0.5(PbTiO_3)

The Lanthanum-doped bismuth ferrite–lead titanate compositions of 0.5(Bi LaxFe1-xO3)–0.5(Pb Ti O3)(x = 0.05,0.10,0.15,0.20)(BLxF1-x-PT) were prepared by mixed oxide method.Structural characterization was performed by X-ray diffraction and shows a tetragonal structure at room temperature.The lattice parameter c/a ratio decreases with increasing of La(x = 0.05–0.20) concentration of the composites.The effect of charge carrier/ion hopping mechanism,conductivity,relaxation process and impedance parameters was studied using an impedance analyzer in a wide frequency range(102–106Hz) at different temperatures.The nature of Nyquist plot confirms the presence of bulk effects only,and non-Debye type of relaxation processes occurs in the composites.The electrical modulus exhibits an important role of the hopping mechanism in the electrical transport process of the materials.The ac conductivity and dc conductivity of the materials were studied,and the activation energy found to be 0.81,0.77,0.76 and 0.74 e V for all compositions of x = 0.05–0.20 at different temperatures(200–300 °C).     

Quantitative Analysis of the Crystallographic Orientation Relationship Between the Martensite and Austenite in Quenching–Partitioning–Tempering Steels

The orientation relationships(ORs)between the martensite and the retained austenite in low-and medium-carbon steels after quenching–partitioning–tempering process were studied in this work.The ORs in the studied steels are identified by selected-area electron diffraction(SAED)as either K–S or N–W ORs.Meanwhile,the ORs were also studied based on numerical fitting of electron backscatter diffraction data method suggested by Miyamoto.The simulated K–S and N–W ORs in the low-index directions generally do not well coincide with the experimental pole figure,which may be attributed to both the orientation spread from the ideal variant orientations and high symmetry of the low-index directions.However,the simulated results coincide well with experimental pole figures in the high-index directions{123}_(bcc).A modified method with simplicity based on Miyamoto’s work was proposed.The results indicate that the ORs determined by modified method are similar to those determined by Miyamoto’method,that is,the OR is near K–S OR for the low-carbon Q–P–T steel,and with the increase of carbon content,the OR is closer to N–W OR in medium-carbon Q–P–T steel.     

Using Finite Element and Contour Method to Evaluate Residual Stress in Thick Ti-6Al-4V Alloy Welded by Electron Beam Welding

This work was to reveal the residual stress profile in electron beam welded Ti-6Al-4V alloy plates(50 mm thick) by using finite element and contour measurement methods.A three-dimensional finite element model of 50-mmthick titanium component was proposed,in which a column–cone combined heat source model was used to simulate the temperature field and a thermo-elastic–plastic model to analyze residual stress in a weld joint based on ABAQUS software.Considering the uncertainty of welding simulation,the computation was calibrated by experimental data of contour measurement method.Both test and simulated results show that residual stresses on the surface and inside the weld zone are significantly different and present a narrow and large gradient feature in the weld joint.The peak tensile stress exceeds the yield strength of base materials inside weld,which are distinctly different from residual stress of the thin Ti-6Al-4V alloy plates presented in references before.     

Microstructures and Tensile Properties of Ultrafine-Grained Ni–(1–3.5) wt% SiC_(NP) Composites Prepared by a Powder Metallurgy Route

Silicon carbide nanoparticle-reinforced nickel-based composites(Ni–Si CNP),with a Si CNPcontent ranged from1 to 3.5 wt%,were prepared using mechanical alloying and spark plasma sintering.In addition,unreinforced pure nickel samples were also prepared for comparative purposes.To characterize the microstructural properties of both the unreinforced pure nickel and the Ni–Si CNPcomposites transmission electron microscopy(TEM) was used,while their mechanical behavior was investigated using the Vickers pyramid method for hardness measurements and a universal tensile testing machine for tensile tests.TEM results showed an array of dislocation lines decorated in the sintered pure nickel sample,whereas,for the Ni–Si CNPcomposites,the presence of nano-dispersed Si CNPand twinning crystals was observed.These homogeneously distributed Si CNPwere found located either within the matrix,between twins or on grain boundaries.For the Ni–Si CNPcomposites,coerced coarsening of the Si CNPassembly occurred with increasing Si CNPcontent.Furthermore,the grain sizes of the Ni–Si CNPcomposites were much finer than that of the unreinforced pure nickel,which was considered to be due to the composite ball milling process.In all cases,the Ni–Si CNPcomposites showed higher strengths and hardness values than the unreinforced pure nickel,likely due to a combination of dispersion strengthening(Orowan effects) and particle strengthening(Hall–Petch effects).For the Ni–Si CNPcomposites,the strength increased initially and then decreased as a function of Si CNPcontent,whereas their elongation percentages decreased linearly.Compared to all materials tested,the Ni–Si CNPcomposite containing 1.5% Si C was found more superior considering both their strength and plastic properties.     

Directional Growth of Tin Crystals Controlled by Combined Solute Concentration Gradient Field and Static Magnetic Field

A new method was introduced to achieve directional growth of Sn crystals. Microstructures in liquid(Pb)/liquid(Sn) diffusion couples were investigated under various static magnetic fields. Results show that the β-Sn crystals mainly reveal an irregular dendritic morphology without or with a relatively low static magnetic field(B0.3 T). When the magnetic field is increased to 0.5 T, the β-Sn dendrites close to the final stage of growth begin to show some directional character. With a further increase in the magnetic field to a higher level(0.8–5 T), the β-Sn dendrites have an enhanced directional growth character, but the dendrites show a certain deflection. As the magnetic field is increased to 12 T, the directional growth of the β-Sn dendrites in the center of the couple is severely destroyed. The mechanism of the directional growth of the β-Sn crystals and the deflection of the β-Sn crystals with the application of static magnetic field was tentatively discussed.     

电化学噪声数据处理方法概述

综述了常见的电化学噪声数据处理方法,介绍了直流趋势剔除、统计分析、快速傅立叶变换(FFT)法计算功率谱密度(PSD)以及小波变换处理电化学噪声信号的基本过程,并阐释了各种数学处理及所得参数的物理意义。