Effects of substrate on the structural, electrical and optical properties of Al-doped ZnO films prepared by radio frequency magnetron sputtering

Transparent and conductive Al-doped ZnO (AZO) thin films were deposited on substrates including alkali-free glass, quartz glass, Si, and SiO₂ buffer layer on alkali-free glass by using radio frequency magnetron sputtering. The effects of different substrates on the structural, electrical and optical properties of the AZO films were investigated. It was found that the crystal structures were remarkably influenced by the type of the substrates due to their different thermal expansion coefficients, lattice mismatch and flatness. The AZO film (100 nm in thickness) deposited on the quartz glass exhibited the best crystallinity, followed sequentially by those deposited on the Si, the SiO₂ buffer layer, and the alkali-free glass. The film deposited on the quartz glass showed the lowest resistivity of 5.14 × 10^− 4 Ω cm among all the films, a carrier concentration of 1.97 × 10²¹ cm^− 3 and a Hall mobility of 6.14 cm²/v·s. The average transmittance of this film was above 90% in the visible light spectrum range. Investigation into the thickness-dependence of the AZO films revealed that the crystallinity was improved with increasing thickness and decreasing surface roughness, accompanied with a decrease in the film resistivity.     

Mn-doped ZnO transparent conducting films deposited by DC magnetron sputtering

Mn-doped zinc oxide (ZnO:Mn) thin films with low resistivity and relatively high transparency were firstly prepared on glass substrate by direct current (DC) magnetron sputtering at room temperature. Influence of film thickness on the properties of ZnO:Mn films was investigated. X-ray diffraction (XRD) and scanning electron microscopy (SEM) show that all the deposited films are polycrystalline with a hexagonal structure and have a preferred orientation along the c-axis perpendicular to the substrate. As the thickness increases from 144 to 479 nm, the crystallite size increases while the electrical resistivity decreases. However, as the thickness increases from 479 to 783 nm, the crystallite size decreases and the electrical resistivity increases. When film thickness is 479 nm, the deposited films have the lowest resistivity of 2.1 × 10^− 4 Ω cm and a relatively high transmittance of above 84% in the visible range.     

Al-doped ZnO thin films deposited by reactive frequency magnetron sputtering: H2-induced property changes

Al-doped ZnO (AZO) transparent conductive thin films have been prepared by radio-frequency magnetron sputtering with a ceramic target (98 wt.% ZnO, 2 wt.% Al₂O₃) in different Ar + H₂ ambient at a substrate temperature of 200 °C. To investigate the influence of H₂-flow on the properties of AZO films, H₂-flow was changed during the growth process with a fixed Ar-flow of 60 sccm. The results indicate that H₂-flow has a considerable influence on the transparent conductive properties of AZO films. The low resistivity in the order of 10^− 4 Ω cm and the high average transmittance more than 92% in the visible range were obtained for the samples prepared in the optimal H₂-flow range from 0.4 sccm to 1.0 sccm. In addition, the influence of H₂-flow on the structure and composition of AZO films have also been studied.     

Improving the electrical and optical properties of DC-sputtered ZnO:Al by thermal post deposition treatments

Thermal post deposition treatments are applied to DC-sputtered aluminum-doped zinc oxide (ZnO:Al) films and lead to a significant improvement of the electrical properties. Protective layers of amorphous silicon are used to protect the films from degradation during the high temperature treatment. Annealing for 6 hours at 500 °C leads to a carrier mobility of 48 cm²/Vs at a carrier concentration of 5.5 · 10²⁰ cm^− 3. Furthermore, improvements in the optical as well as in the electrical properties are possible at the same time compared to the as-deposited film. This is achieved by carrying out two thermal treatments to the ZnO:Al film, one prior to the capping with the protective layer and one afterwards. A series of samples with different carrier concentrations allows us to draw conclusions on the specific electrical transport properties.     

Deposition of Al-doped ZnO films on polyethylene naphthalate substrate with radio frequency magnetron sputtering

100 nm Al-doped ZnO (AZO) thin films were deposited on polyethylene naphthalate (PEN) substrates with radio frequency magnetron sputtering using 2 wt.% Al-doped ZnO target at various deposition conditions including sputtering power, target to substrate distance, working pressure and substrate temperature. When the sputtering power, target to substrate distance and working pressure were decreased, the resistivity was decreased due to the improvement of crystallinity with larger grain size. As the substrate temperature was increased from 25 to 120 °C, AZO films showed lower electrical resistivity and better optical transmittance due to the significant improvement of the crystallinity. 2 wt.% Al-doped ZnO films deposited on glass and PEN substrates at sputtering power of 25 W, target to substrate distance of 6.8 cm, working pressure of 0.4 Pa and substrate temperature of 120 °C showed the lowest resistivity (5.12 × 10^− 3 Ω cm on PEN substrate, 3.85 × 10^− 3 Ω cm on glass substrate) and high average transmittance (> 90% in both substrates). AZO films deposited on PEN substrate showed similar electrical and optical properties like AZO films deposited on glass substrates.     

Dependence of the electrical and optical properties on the bias voltage for ZnO:Al films deposited by r.f. magnetron sputtering

Aluminum-doped zinc oxide (ZnO:Al) thin films were deposited on glass, polycarbonate (PC), and polyethylene terephthalate (PET) substrates by r.f. magnetron sputtering. The substrate dc bias voltage varied from 0 V to 50 V. Structural, electrical and optical properties of the films were investigated. The deposition rate of ZnO:Al films on glass substrate initially increased with the bias voltage, and then decreased with further increasing bias voltage. It was found that the best films on glass substrate with a low as 6.2 × 10^− 4 Ω cm and an average transmittance over 80% at the wavelength range of 500-900 nm can be obtained by applying the bias voltage of 30 V. The properties of the films deposited on polymer substrate, such as PC and PET, have a similar tendency, with slightly inferior values to those on glass substrate.     

Electrical, optical, and structural properties of InZnSnO electrode films grown by unbalanced radio frequency magnetron sputtering

We have investigated the electrical, optical, structural, and annealing properties of indium zinc tin oxide (IZTO) films prepared by an unbalanced radio frequency (RF) magnetron sputtering at room temperature, in a pure Ar ambient environment. It was found that the electrical and optical properties of unbalanced RF sputter grown IZTO films at room temperature were influenced by RF power and working pressure. At optimized growth condition, we could obtain the IZTO film with the low resistivity of 3.77 × 10^− 4 Ω cm, high transparency of ~ 87% and figure of merit value of 21.2 × 10^− 3Ω^− 1, without the post annealing process, even though it was completely an amorphous structure due to low substrate temperature. In addition, the field emission scanning electron microscope analysis results showed that all IZTO films are amorphous structures with very smooth surfaces regardless of the RF power and working pressure. However, the rapid thermal annealing process above the temperature of 400 °C lead to an abrupt increase in resistivity and sheet resistance due to the transition of film structure from amorphous to crystalline, which was confirmed by X-ray diffraction examination.     

Effects of sputtering pressure and Al buffer layer thickness on properties of AZO films grown by rf magnetron sputtering

Transparent and conductive Al-doped (2 wt.%) zinc oxide (AZO) films were deposited on inexpensive soda-lime glass substrates by using rf magnetron sputtering at room temperature. This study analyzed the effects of argon sputtering pressure, which varied in the range from 0.46 to 2.0 Pa, on the morphological, electrical and optical properties of AZO films. The only (0 0 2) diffraction peak of the film were observed at 2θ～34.45°, exhibiting that the AZO films had hexagonal ZnO wurtzite structure, and a preferred orientation with the c-axis perpendicular to the substrate. By applying a very thin aluminum buffer layer with the thickness of 2 nm, findings show that the electrical resistivity was 9.46 × 10⁻⁴ Ω-cm, and the average optical transmittance in the visible part of the spectra was approximately 81%. Furthermore, as for 10 nm thick buffer layer, the electrical resistivity was lower, but the transmittance was decreased.     

Control of aluminum doping of ZnO:Al thin films obtained by high-power impulse magnetron sputtering

This work reports a method used to control Al doping of ZnO thin films deposited by high-power impulse magnetron sputtering of a pure Zn target in low-pressure Ar/O₂ gas mixture. The method uses sputtering of an electrically negative biased aluminum electrode placed in the proximity of the negative glow of the magnetron discharge. Resonant laser absorption measurements of Al atom concentration in vapor phase and the X-ray Photoelectron Emission Spectroscopy measurements of Al concentration in the deposited ZnO:Al films confirm that the electrode biasing potential is the key parameter that controls the Al doping process. Optically transparent ZnO:Al films with resistivity as low as 3.6 × 10^− 3 Ω × cm have been obtained at an optimum value of Al concentration of 1.5 at.%. It has been found that the film electrical conductivity is limited by the effect of decreasing of crystalline grain size in the films with the increased Al doping concentration.     

Control of the optical properties of silicon and chromium mixed oxides deposited by reactive magnetron sputtering

The development of mixed-oxide thin films allows obtaining materials with better properties than those of the different binary oxides, which makes them suitable for a great number of applications in different fields, such as tribology, optics or microelectronics. In this paper we investigate the deposition of mixed chromium and silicon oxides deposited by reactive magnetron sputtering with a view to use them as optical coatings with an adjustable refractive index. These films have been characterized by means of Rutherford backscattering spectrometry, Auger electron spectroscopy, X-ray diffraction, scanning electron microscopy, Fourier-transform infrared spectroscopy and spectroscopic ellipsometry so as to determine how the deposition conditions influence the characteristics of the material. We have found that the deposition parameter whose influence determines the properties of the films to a greater extent is the amount of oxygen in the reactive sputtering gas.     

Influence of annealing temperature on the properties of ZnO:Zr films deposited by direct current magnetron sputtering

Transparent conducting zirconium-doped zinc oxide (ZnO:Zr) films were deposited on quartz substrates by direct current (DC) magnetron sputtering at room temperature. The influence of post-annealing temperature on the structural, morphological, electrical and optical properties of ZnO:Zr films were investigated. When annealing temperature increases from room temperature to 573 K, the resistivity decreases obviously due to an improvement of the crystallinity. However, with further increase in annealing temperature, the crystallinity deteriorates leading to an increase in resistivity. The films annealed at the optimum annealing temperature of 573 K in vacuum have the lowest resistivity of 9.8 × 10⁻⁴ Ω cm and a high transmittance of above 92% in the visible range.     

Structural, optical, and electrical properties of AZO films by tilted angle sputtering method

We investigate the structural, optical, and electrical properties of aluminum-doped zinc oxide (AZO) films on Si substrate by a tilted angle sputtering method. The substrate holder is tilted by varying the angle from θ_sh = 0° to θ_sh = 80° during the sputtering process. As the tilted angle is increased, the deposition rate is increased due to the decreased distance between the substrate and the target. Without substrate rotation, the deposited AZO films exhibit apparently the inclined nanocolumnar structures, depending on the tilted angle. The refractive index, which is related to the porosity within films, is reduced for the larger inclined nanocolumnar structure while the extinction coefficient remains almost the same in the visible wavelength range. The inclination of nanocolumns disappears when the substrate is rotated. On glass substrate, the electrical properties as well as optical transmittance of AZO films are also dependant on the tilted angle.     

Structures and properties of the Al-doped ZnO thin films prepared by radio frequency magnetron sputtering

Al-doped ZnO thin films were deposited by radio frequency magnetron sputtering using a ZnO target with 2 wt.% Al₂O₃. The structures and properties of the films were characterized by the thin film X-ray diffraction, high resolution transmission electron microscopy, Hall system and ultraviolet/visible/near-infrared spectrophotometer. The Al-doped ZnO film with high crystalline quality and good properties was obtained at the sputtering power of 100 W, working pressure of 0.3 Pa and substrate temperature of 250 °C. The results of further structure analysis show that the interplanar spacings d are enlarged in other directions besides the direction perpendicular to the substrate. Apart from the film stress, the doping concentration and the doping site of Al play an important role in the variation of lattice parameters. When the doping concentration of Al is more than 1.5 wt.%, part of Al atoms are incorporated in the interstitial site, which leads to the increase of lattice parameters. This viewpoint is also proved by the first principle calculations.     

利用脉冲直流磁控溅射制备ZnO:Al薄膜的研究

利用中频脉冲直流磁控溅射法制备了平面ZnO:Al(AZO)透明导电薄膜,研究了沉积压力、衬底温度和溅射功率对AZO薄膜光电性能、薄膜稳定性的影响.结果表明:在较低沉积压力、衬底温度及溅射功率下,可获得具有低电阻率、高透过率、高稳定性的AZO薄膜.     

衬底温度对磁控溅射法制备ZnO薄膜结构及光学特性的影响

采用射频反应磁控溅射法在玻璃衬底上制备了具有c轴高择优取向的ZnO薄膜,利用X射线衍射仪、扫描探针显微镜及紫外分光光度计研究了生长温度对ZnO薄膜的结构及光学吸收和透射特性的影响.结果表明,合适的衬底温度有利于提高ZnO薄膜的结晶质量;薄膜在紫外区显示出较强的光吸收,在可见光区的平均透过率达到90%以上,且随着衬底温度的升高,薄膜的光学带隙减小、吸收边红移.采用量子限域模型对薄膜的光学带隙作了相应的理论计算,计算结果与实验值符合得较好.     

ZnO:Al Films Prepared by Reactive Mid-frequency Magnetron Sputtering with Rotating Cathode

Al-doped zinc oxide (ZnO:Al,AZO) films were deposited on glass substrates using a reactive mid-frequency (MF) magnetron sputtering process with rotating cathodes.The influence of deposition parameters on structural,electrical and optical properties of AZO films is investigated.It is observed that the rotating magnetron targets exhibited a sputtered metallic surface over a wider range,and there is no re-deposition zone between the racetracks.The films deposited at static deposition mode demonstrate more homo...     

射频磁控溅射制备Mn掺杂ZnO薄膜的结构与光学性能

采用反应射频磁控溅射方法制备Zn1-xMnxO薄膜(0≤x≤0.25),并在不同温度下进行退火处理.通过原子力显微镜、薄膜X射线衍射、透射电子显微镜和透射光谱对薄膜的成分、表面形貌、微结构和光学性质进行了研究.结果表明,薄膜结晶质量明显地依赖于掺杂Mn元素的浓度,所有薄膜都表现了沿(002)晶面方向择优取向生长,当Mn...     

Effect of target properties on transparent conducting impurity-doped ZnO thin films deposited by DC magnetron sputtering

For the purpose of using transparent conducting impurity-doped ZnO thin films in liquid crystal display (LCD) applications, the relationship between the properties of dc magnetron sputtering (dc-MS) deposited thin films and the properties of the oxide targets used to produce them is investigated. Both Al-doped and Ga-doped ZnO (AZO and GZO) thin films were deposited on glass substrates using a dc-MS apparatus with various high-density sintered AZO or GZO disk targets (diameter of about 150 mm); the target and substrate were both fixed during the depositions. Using targets with a lower resistivity results in attaining more highly stable dc-MS depositions with higher deposition rates and lower arcing. In addition, dc-MS depositions using targets with a lower resistivity produced improvements in resistivity distribution on the substrate surface. It was found that the oxygen content in deposited thin films decreased as the oxygen content of the target used in the deposition was decreased. As a result, the dc-MS deposition of transparent conducting impurity-doped ZnO thin films suitable for LCD applications requires the preparation of significantly reduced AZO and GZO targets with low oxygen content.     

Optimization of ZnO:Al/Ag/ZnO:Al structures for ultra-thin high-performance transparent conductive electrodes

Al-doped ZnO (AZO)/Ag/AZO multilayer coatings (50-70 nm thick) were grown at room temperature on glass substrates with different silver layer thickness, from 3 to 19 nm, by using radio frequency magnetron sputtering. Thermal stability of the compositional, optical and electrical properties of the AZO/Ag/AZO structures were investigated up to 400 °C and as a function of Ag film thickness. An AZO film as thin as 20 nm is an excellent barrier to Ag diffusion. The inclusion of 9.5 nm thin silver layer within the transparent conductive oxide (TCO) material leads to a maximum enhancement of the electro-optical characteristics. The excellent measured properties of low resistance, high transmittance in the visible spectral range and thermal stability allow these ultra-thin AZO/Ag/AZO structures to compete with the 1 μm thick TCO layer currently used in thin film solar cells.     

Effects of deposition temperature on structure and properties of mo-doped indium oxide by radio frequency magnetron sputtering

Transparent conductive oxide (TCO) thin films of Mo-doped In₂O₃ (IMO) were prepared on glass substrates by radio frequency magnetron sputtering from the 2 wt% Mo-doped In₂O₃ ceramic target. The depositions were carried out under an oxygen-argon atmosphere by varying the deposition temperature from 200 °C to 350 °C. The crystal structure and thickness of IMO thin films were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The effects of deposition temperature on the electrical and optical transmittance properties of IMO thin films were investigated by four-point probe Hall system and UV-VIS-NIR spectrophotometer separately. The optimum deposited IMO thin films were obtained with resistivity of 6.9 × 10⁻⁴ Ω cm and carrier mobility 45 cm²v⁻¹s⁻¹ at 350 °C. The average optical transmittance of IMO films on glass substrates are over 80% in the near-infrared region.