A parabolic dish/AMTEC solar thermal power system and its performance evaluation

This paper proposes a parabolic dish/AMTEC solar thermal power system and evaluates its overall thermal–electric conversion performance. The system is a combined system in which a parabolic dish solar collector is cascaded with an alkali metal thermal to electric converter (AMTEC) through a coupling heat exchanger. A separate type heat-pipe receiver is selected to isothermally transfer the solar energy from the collector to the AMTEC. To assess the system’s overall thermal–electric conversion performance, a theoretical analysis has been undertaken in conjunction with a parametric investigation by varying relevant parameters, i.e., the average operating temperature and performance parameters associate with the dish collector and the AMTEC. Results show that the overall conversion efficiency of parabolic dish/AMTEC system could reach up to 20.6% with a power output of 18.54 kW corresponding to an operating temperature of 1280 K. Moreover, it is found that the optimal condenser temperature, corresponding to the maximum overall efficiency, is around 600 K. This study indicates that the parabolic dish/AMTEC solar power system exhibits a great potential and competitiveness over other solar dish/engine systems, and the proposed system is a viable solar thermal power system.     

Energy and exergy performance assessment of a novel solar-based integrated system with hydrogen production

In this study, a new solar power assisted multigeneration system designed and thermodynamically analyzed. In this system, it is designed to perform heating, cooling, drying, hydrogen and power generation with a single energy input. The proposed study consists of seven sub-parts which are namely parabolic dish solar collector, Rankine cycle, organic Rankine cycle, PEM-electrolyzer, double effect absorption cooling, dryer and heat pump. The effects of varying reference temperature, solar irradiation, input and output pressure of high-pressure turbine and pinch point temperature heat recovery steam generator are investigated on the energetic and exergetic performance of integration system. Thermodynamic analysis result outputs show that the energy and exergy performance of overall study are computed as 48.19% and 43.57%, respectively. Moreover, the highest rate of irreversibility has the parabolic dish collector with 24,750 kW, while the lowest rate of irreversibility is calculated as 5745 kW in dryer. In addition, the main contribution of this study is that the solar-assisted multi-generation systems have good potential in terms of energy and exergy efficiency.     

A solar-powered traveling-wave thermoacoustic electricity generator

Traveling-wave thermoacoustic electricity generator is a new external-combustion type device capable of converting heat such as solar energy into electric power. In this paper, a 1 kW solar-powered traveling-wave thermoacoustic electricity generation system is designed and fabricated. The system consists of a traveling-wave thermoacoustic electricity generator, a solar dish collector and a heat receiver. In the preliminary tests, using electric cartridge heaters to simulate the solar energy, a maximum electric power of 481 W and a maximum thermal-to-electric efficiency of 15.0% were achieved with 3.5 MPa pressurized helium and 74 Hz working frequency. Then, after integrating the traveling-wave thermoacoustic electricity generator with the solar dish collector and the heat receiver, the solar-powered experiments were performed. In the experiments, a maximum electric power of about 200 W was obtained. However, due to the solar dish collector problems, the heating temperature of the receiver was much lower than expected. Optimizations of the collector and the heat receiver are under way.     

Investigation into topping cycle: Thermal efficiency with and without presence of thermoelectric generator

Thermoelectric power generation due to solar heating is a current interest in green energy research. One of the applications of the thermoelectric power generator is involved with the topping cycle, in which the thermoelectric generators were placed on the heat collector elements of a conventional solar concentration power plant. Although the topping cycle is practical and easy to operate, the efficiency of the thermal system with and without thermoelectric generator needs to be examined. In the present study, thermal efficiency of the topping cycle is analyzed and compared with its counterpart without the presence of the thermoelectric elements. Thermodynamic analysis for the efficiency of both the systems with and without thermoelectric generator is presented. The fluid flow and heat transfer in a tube with presence of thermoelectric elements resembling the solar heating system incorporated in the topping cycle are simulated numerically. It is found that, for a certain combination of operating and thermoelectric device parameters, thermal efficiency of the topping cycle becomes slightly higher than that of the same system without the presence of the thermoelectric generators.     

Experimental investigation of effect of variation of mass flow rate on performance of parabolic dish water heater with non-coated receiver

Concentrated solar collectors have high efficiency. Therefore, when concentrating collectors are used for water heating application, the system yields higher efficiency. From a hot climate perspective, there is a huge potential available for low-cost solar water heating systems. With the system described in this paper, the needs of hot water in the domestic sector can be fulfilled instantly. Authors used the parabolic dish collector for instant water heating. This paper describes the effect of variation of mass flow rate on performance of the parabolic dish water heater prototype. Design of the solar parabolic dish collector consists of a novel truncated cone-shaped helical coiled receiver made up of copper at focal point. This prototype was evaluated for its performance during the month of April and May 2010.     

Solar assisted multi-generation system using nanofluids: A comparative analysis

In this comparative study, a parabolic trough solar collector and a parabolic dish solar collector integrated separately with a Rankine cycle and an electrolyzer are analyzed for power as well as hydrogen production. The absorption fluids used in the solar collectors are Al₂O₃ and Fe₂O₃ based nanofluids and molten salts of LiCl–RbCl and NaNO₃–KNO₃. The ambient temperature, inlet temperature, solar irradiance and percentage of nanoparticles are varied to investigate their effects on heat rate and net power produced, the outlet temperature of the solar receiver, overall energy and exergy efficiencies and the rate of hydrogen produced. The results obtained show that the net power produced by the parabolic dish assisted thermal power plant is higher (2.48 kW–8.17 kW) in comparison to parabolic trough (1 kW–6.23 kW). It is observed that both aluminum oxide (Al₂O₃) and ferric oxide (Fe₂O₃) based nanofluids have better overall performance and generate higher net power as compared to the molten salts. An increase in inlet temperature is observed to decrease the hydrogen production rate. The rate of hydrogen production is found to be higher using nanofluids as solar absorbers. The hydrogen production rate for parabolic dish thermal power plant and parabolic trough thermal power plant varies from 0.0098 g/s to 0.0322 g/s and from 0.00395 g/s to 0.02454 g/s, respectively.     

Thermodynamic investigation of a concentrating solar collector based combined plant for poly-generation

The detailed thermodynamic evaluation for combined system assisted on solar energy for poly-generation are studied in this paper. This poly-generation cycle is operated by the concentrating solar radiation by using the parabolic dish solar collector series. The beneficial exits of this integrated plant are the electricity, fresh-water, hot-water, heating-cooling, and hydrogen while there are different heat energy recovery processes within the plant for development performance. A Rankine cycle with three turbines is employed for electricity production. In addition to that, the desalination aim is performed by utilizing the waste heat of electricity production cycle in a membrane distillation unit for fresh-water generation. Also, a PEM electrolyzer sub-component is utilized for hydrogen generation aim in the case of excess power generation. Finally, the hot-water production cycle is performed via the exiting working fluid from the very high-temperature generator of the cooling cycle. Moreover, based on the thermodynamic assessment outputs, the whole energy and exergy efficiencies of 58.43% and 54.18% are computed for the investigated solar plant, respectively.     

Exergetic analysis and performance evaluation of parabolic dish Stirling engine solar power plant

In this communication, a 50 MW_e design capacity parabolic dish Stirling engine solar power plant (PDSSPP) has been modeled for analysis, where 2000 units of parabolic dish Stirling engine each having capacity of 25 kW_e were considered to get desired capacity. An attempt has been made to carry out the energetic and exergetic analysis of different components of a solar power plant system using parabolic dish collector/receiver and Stirling engine. The energetic and exergetic losses as well as efficiencies for typical PDSSPP under the typical operating conditions have been evaluated. Variations of the efficiency of Stirling engine solar power plant at the part‐load condition are considered for year‐round performance evaluation. The developed model is examined at location Jodhpur (26.29°N, 73.03°E) in India. It is found that year‐round energetic efficiency varies from 15.57% to 27.09%, and exergetic efficiency varies from 16.83% to 29.18%. The unit cost of electric energy generation (kW_eh) is about 8.76 Indian rupees (INR), with 30 years life span of the plant and 10% interest rate on investment. Copyright © 2012 John Wiley & Sons, Ltd.     

基于太阳能光伏热利用的光伏/热电(PV/TV)建筑一体化试验研究

将太阳能电池板、集热器、热电发电片结合起来,设计并制成了一套光伏/热电(PV/TV)系统,在利用太阳能电池发电的同时,收集热量并利用其发电。在北京地区进行了该系统的室外模拟试验,测试并讨论了该系统在不同结构和不同环境下的性能,探讨该系统在光伏建筑中的应用。试验结果表明,与单纯的光伏发电系统或太阳能热水系统相比,PV/TV系统具有占地面积小、综合效率高等优点。     

Experimental performance investigation of modified cavity receiver with fuzzy focal solar dish concentrator

In this paper, thermal performance analysis of 20 m² prototype fuzzy focal solar dish collector is presented. The focal image characteristics of the solar dish are determined to propose the suitable design of absorber/receiver. First, theoretical thermal performance analysis of the fuzzy focal solar parabolic dish concentrator with modified cavity receiver is carried out for different operating conditions. Based on the theoretical performance analysis, the total heat loss (conduction, convection and radiation heat losses) from the modified cavity receiver is estimated. It is observed that the maximum theoretical efficiencies of solar dish collector are found to be as 79.2% for no wind conditions and 78.2% and 77.8% for side-on and head-on winds speed of 5 m/s respectively. Latter, real time analysis of parabolic dish collector with modified cavity receiver is carried out in terms of stagnation test, time constant test and daily performance test. From stagnation test, the overall heat loss coefficient is found to be 356 W/m² K. The time constant test is carried out to determine the influence of sudden change in solar radiation at steady state conditions. The daily performance tests are conducted for different flow rates. It is found that the efficiency of the collector increases with the increase of volume flow rates. The average thermal efficiencies of the parabolic dish collector for the volume flow rate of 100 L/h and 250 L/h are found to be 69% and 74% for the average beam radiation (I_bn) of 532 W/m² and 641 W/m² respectively.     

Numerical simulation and experiment research of radiation performance in a dish solar collector system

The Monte Carlo ray-tracing method is applied and coupled with optical properties to predict the radiation performance of solar concentrator/cavity receiver systems. Several different cavity geometries are compared on the radiation performance. A flux density distribution measurement system for dish parabolic concentrators is developed. The contours of the flux distribution for target placements at different distances from the dish vertex of a solar concentrator are taken by using an indirect method with a Lambert and a charge coupled device (CCD) camera. Further, the measured flux distributions are compared with a Monte Carlo-predicted distribution. The results can be a valuable reference for the design and assemblage of the solar collector system.     

Performance of Cylindrical Parabolic Collector with Automated Tracking System

Parabolic solar collector collects the radiant energy emitted from the sun and focuses it at a point. Parabolic trough collectors are the low cost implementation of concentrated solar power technology that focuses incident sun light on to a tube filled with a heat transfer fluid. However, the basic problem with the cylindrical parabolic collector without tracking was the solar collector does not move with the orientation of sun. Development of automatic tracking system for cylindrical parabolic collectors will increase solar collection as well as efficiency of devices. The main aim of this paper is to design, fabricate and analyze the performance of parabolic collector with automated tracking system. The automated tracking mechanism is used to receive the maximum possible energy of solar radiation as it tracks the path of sun. The performance of the parabolic trough collector is experimentally investigated with the water circulated as heat transfer fluid. The collector efficiency will be noted.     

Utilizing the multi-objective particle swarm optimization for designing a renewable multiple energy system on the basis of the parabolic trough solar collector

Today, to preserve fossil resources, mankind has to search for new ways to respond to its ever-increasing energy needs. In this study, a hybrid system of energy and the use of a parabolic trough solar collector to attract solar radiation was investigated to produce clean electricity, cooling, and hydrogen from thermodynamic and economic aspects. The designed system consisted of a parabolic trough solar collector, organic Rankine cycle, lithium-bromide absorption refrigeration cycle, and proton exchange membrane electrolysis system. The evaporator input temperature, turbine inlet temperature, solar radiation intensity, mass flow rate of collector and parabolic trough collector surface area were set as decision variables and the effect of these parameters on system performance and system exergy loss were investigated. The objective functions of this research were exergy efficiency and cost rate. In order to optimize this system, multi-objective particle swarm optimization algorithm was employed. Optimization results with particle swarm optimization indicated that the best rate of exergy efficiency is 3.12% and the system cost rate is 16.367 US$ per hour, at the same time. The system is capable of producing 15.385 kW power, 0.189 kg/day hydrogen and 56.145 kW cooling in its optimum condition. The results of sensitivity analysis showed that increasing mass flow rate at the collector, temperature at the evaporator inlet, and temperature at the turbine inlet have positive effect on the performance of the proposed system.     

Evaluation of a large dish‐type concentrator solar lighting system for underground car park

To utilize solar energy more efficiently and reduce lighting power consumption in underground public spaces such as car park, a large dish‐type concentrator solar lighting system is put forward along with its evaluation, which is a unique design to apply a laminated layer of beam split thin‐film coating and thin‐film solar cells onto the dish reflector. The collected sunlight is split into 2 parts, one being reflected into a fiber optical bundle and transmitted for daylighting, while the rest being absorbed by solar cells for electricity generation as the other way to replenish daylighting. A set of 4 solar lighting systems using 3.28‐m diameter dish are designed to meet the lighting requirement in a 1771‐m² underground car park. A mathematical model is adopted to calculate the output power and conversion efficiency of solar cells distributed on the parabolic dish surface. The indoor illuminance distribution is given by lighting simulation. The results indicate that the average daylight illuminance in the car park can vary between 62.7 and 284 lx on February 25, 2016 and between 62.7 and 353 lx on August 17, 2016 for 2 chosen days, respectively. For the presented design, the electricity produced by solar cells is just enough to power light‐emitting diodes for lighting meeting a criterion at night. Considering about 19% conversion efficiency of solar cells and the efficacy of 129.5 lm/W of light‐emitting diodes, the hybrid solar lighting system can have about 40% utilization ratio of solar energy, so it can be concluded that a sufficient lighting provision can be provided by the proposed large dish‐type concentrator solar lighting system for applications in underground car park.     

Electricity generation using solar parabolic dish system with thermoelectric generator—An experimental investigation

The present electricity grid installation cost as well as the tariff is quite high in India, particularly remote rural areas, to electrify houses. These problems can be easily solved by installing standalone systems that operate on one of the clean energy sources such as solar energy. An experimental analysis of generating electricity from a thermoelectric generator (TEG) powered by a solar parabolic dish concentrator device with aperture area and focal length of 12.6 m² and 2.42 m, respectively, is presented in this article. A TEG is made up of a thermoelectric module connected to a flat receiver by an absorber layer. The studies were carried out in Indian climatic conditions at the National Institute of Technology, Puducherry. Over a spectrum of beam radiation, the system's maximum energy conversion efficiency, as well as efficient electrical output, are evaluated and presented. The proposed system's average effective electrical efficiency is 0.424%, corresponding to the TEG's average energy conversion efficiency of 2.76%.     

Comparative energy,exergy and exergo-economic analysis of solar driven supercritical carbon dioxide power and hydrogen generation cycle

Parabolic dish solar collector system has capability to gain higher efficiency by converting solar radiations to thermal heat due to its higher concentration ratio. This paper examines the exergo-economic analysis, net work and hydrogen production rate by integrating the parabolic dish solar collector with two high temperature supercritical carbon dioxide (s-CO₂) recompression Brayton cycles. Pressurized water (H₂O) is used as a working fluid in the solar collector loop. The various input parameters (direct normal irradiance, ambient temperature, inlet temperature, turbine inlet temperature and minimum cycle temperature) are varied to analyze the effect on net power output, hydrogen production rate, integrated system energetic and exergetic efficiencies. The simulations has been carried out using engineering equation solver (EES). The outputs demonstrate that the net power output of the integrated reheat recompression s-CO₂ Brayton system is 3177 kW, whereas, without reheat integrated system has almost 1800 kW net work output. The overall energetic and exergetic efficiencies of former system is 30.37% and 32.7%, respectively and almost 11.6% higher than the later system. The hydrogen production rate of the solarized reheat and without reheat integrated systems is 0.0125 g/sec and 0.007 g/sec, accordingly and it increases with rise in direct normal irradiance and ambient temperature. The receiver has the highest exergy destruction rate (nearly 44%) among the system components. The levelized electricity cost (LEC) of 0.2831 $/kWh with payback period of 9.5 years has proved the economic feasibility of the system design. The increase in plant life from 10 to 32 years with 8% interest rate will decrease the LEC from (0.434-0.266) $/kWh. Recuperators have more potential for improvement and their cost rate of exergy is higher as compared to the other components.     

Performance analysis of a double-pass thermoelectric solar air collector

The thermoelectric (TE) solar air collector, sometimes known as the hybrid solar collector, generates both thermal and electrical energies simultaneously. A double-pass TE solar air collector has been developed and tested. The TE solar collector was composed of transparent glass, air gap, an absorber plate, thermoelectric modules and rectangular fin heat sink. The incident solar radiation heats up the absorber plate so that a temperature difference is created between the thermoelectric modules that generates a direct current. Only a small part of the absorbed solar radiation is converted to electricity, while the rest increases the temperature of the absorber plate. The ambient air flows through the heat sink located in the lower channel to gain heat. The heated air then flows to the upper channel where it receives additional heating from the absorber plate. Improvements to the thermal and overall efficiencies of the system can be achieved by the use of the double-pass collector system and TE technology. Results show that the thermal efficiency increases as the air flow rate increases. Meanwhile, the electrical power output and the conversion efficiency depend on the temperature difference between the hot and cold side of the TE modules. At a temperature difference of 22.8 °C, the unit achieved a power output of 2.13 W and the conversion efficiency of 6.17%. Therefore, the proposed TE solar collector concept is anticipated to contribute to wider applications of the TE hybrid systems due to the increased overall efficiency.     

Heat pipes thermoelectric solar collectors for energy applications

This study investigates the load characteristics of heat pipe thermoelectric solar collector (HPTSC) in practice. Heat pipe thermoelectric solar collector converts the heat generated by the Sun directly into electrical energy and produces hot water as well. The maximum power in HPTSC is obtained when the internal resistance of the thermoelectric module is equal to the load resistance. It has been observed to be possible to produce both hot water and electricity by improving available solar collectors or producing new generation HPTSC. While it is possible to generate an electrical power of 160 W from a HPTSC of one square meter using the thermoelectric method, the power produced with an average photovoltaic panel with the same area is only 132 W. Accordingly, HPTSC is a superior alternative not only to available solar collectors, but also to available PV panels. HPTSC, involving three different technologies, is environmentally friendly and certainly a product that allows for more efficient use of solar energy.