Study on the smoke back‐layering and critical ventilation in the road tunnel fire at high altitude

A series of numerical simulations were conducted in order to investigate the characteristics of smoke back‐layering and critical ventilation in the road tunnel at high altitude with reduced ambient atmospheric pressures. The results indicated that the smoke back‐layering length decreases with the reduction of ambient pressure. Meanwhile, the dimensionless critical longitudinal ventilation velocity decreases with one‐third power of the factor of ambient pressure at high altitude. By modifying the traditional dimensionless fire heat release rate with ambient pressure, new models were deduced to predict the smoke back‐layering length and critical ventilation velocity in the road tunnel at high altitude.     

Effects of passenger blockage on smoke flow properties in longitudinally ventilated tunnel fires

This paper investigates the effects of passenger blockage on smoke flow properties in longitudinally ventilated tunnel fires. A series of numerical simulations were conducted in a 1/5 small-scale tunnel with the different heat release rates (50-100 kW), longitudinal ventilation velocities (0.5-1 m/s), passenger blockage lengths (2-6 m), and ratios (0.17-0.267). The typical smoke flow properties in different tunnel fire scenarios are analyzed, and the results show that under the same heat release rate and longitudinal ventilation velocity, the smoke back-layering length, maximum smoke temperature, and downstream smoke layer height decrease with increasing passenger blockage length or ratio. The Li correlations can well predict the smoke back-layering length and maximum smoke temperature in tunnel fire scenarios without the passenger blockage. When the passenger blockage exists, the modified local ventilation velocity that takes the blockage length and ratio into account has been proposed to correct the Li correlations. The smoke back-layering length and maximum smoke temperature with the different blockage lengths and ratios can be predicted by the modified correlations, which are shown to well reproduce the simulation results.     

A numerical study on the effects of naturally ventilated shaft and fire locations in urban tunnels

In more and more tunnels, natural ventilation mode with vertical shafts has been gradually employed. However, there are few studies investigating the influences of fire and shaft positions on natural ventilation performance currently. Therefore, this study investigated the effects of the transverse distance from fire source to tunnel sidewall, the longitudinal distance from fire source to shaft, and the transverse distance from shaft to sidewall on natural ventilation effectiveness in a tunnel fire by using Fire Dynamics Simulator. The typical characteristic parameters of smoke, such as mass flow rate, temperature distribution, and velocity vector were analyzed; besides, the phenomenon of plug‐holing was discussed. The results have shown that the mass flow rate of gas exhausted by the shaft decreases slightly with the increase of longitudinal distance from fire source to shaft. When the longitudinal distance from fire source to shaft is constant, changing the transverse distance from shaft to sidewall will have a more obvious effect on the effectiveness of exhausting smoke than changing the transverse distance from fire source to sidewall; in addition, the phenomenon of plug‐holing is more serious when the shaft is close to the sidewall.     

Critical ventilation velocity under the blockage of different metro train in a long metro tunnel

To address the effect of metro train blockage on the critical ventilation velocity in a long tunnel, a series of scenarios were conducted numerically through this study, including different fire sizes (5-10 MW), metro train lengths (80-120 m), and blockage ratios (φ, 0.50, and 0.57). It is known from the numerical results that the metro train length shows a limited effect on the critical ventilation velocity, which is because the longitudinal ventilation has become stable before reaching the fire source to prevent smoke back-layering, and increasing the metro train length only increases the distance of stabilizing the longitudinal ventilation. The blockage ratio shows an obvious influence on the critical ventilation velocity, which is because the presence of the metro train can obviously reduce the flow cross-sectional area of the tunnel. An empirical model is developed as well, while it is known that the critical ventilation velocity increases with the one-third power of dimensionless heat release rate and (1-φ). The research outcomes of this study provide a technical guide for the design of the metro tunnel and the relevant emergency management of fire rescue under fire conditions.     

Study of smoke movement characteristics in tunnel fires in high-altitude areas

Understanding smoke temperature distributions and transport characteristics is of great importance to control and exhaust thermal-driven smoke. However, previous studies have focused on this problem in plain areas, whereas ambient pressure decreases as elevation increases. This study investigates the influence of ambient pressure on the hot gas temperature distribution and movement characteristics in a tunnel fire. A series of numerical simulations are carried out in a vehicle tunnel with various heat release rates (HRRs) and ambient pressures. The results show that the maximum temperature and longitudinal temperature distribution under the tunnel ceiling increase with decreasing ambient pressure due to less heat loss caused by lower air density. In addition, the vertical temperatures of the smoke are slightly higher under lower ambient pressure, and this phenomenon makes the smoke spread slightly faster while the smoke layer thickness remains nearly the same under different ambient pressures. The results can provide a reference for tunnel lining design and ventilation arrangements in high-altitude areas.     

Numerical analysis of smoke flow under the effect of longitudinal airflow in a tunnel fire

This study investigated the influence of the longitudinal airflow on the smoke propagation in a tunnel by large-eddy simulation, which is now widely applied to study the turbulent flow. The smoke movement characteristics were studied in detail, with varying the longitudinal airflow in the tunnel. Six fire scenarios have been simulated with Fire Dynamics Simulator (FDS) and the results of the longitudinal distribution of CO concentration, temperature distribution, interface height, stratification, and the efficiency of smoke extraction in the tunnel have been analyzed to evaluate the different fire cases. FDS predicted a CO concentration distribution compared to calculated values using the Hu model. Furthermore, the predicted maximum smoke temperatures are compared to those given by the Kurioka model. A reasonably good agreement has been obtained for both models. The obtained results showed that the increase of the forced airflow velocity has for results a loss of stratification and significant decrease in the efficiency of extraction.     

Experimental investigation on fire smoke bifurcation flow in longitudinal ventilated tunnels

Investigation of smoke bifurcation flow has been receiving more attentions, however, delicate quantitative analyses on different regions of the bifurcation flow have rarely been addressed. In this study, a series of small-scale experiments were conducted to investigate smoke bifurcation flow in longitudinal ventilated tunnels. Results show that when longitudinal ventilation velocity increases to a certain value, the smoke bifurcation phenomenon emerges, and a low-temperature region forms in the center of the tunnel. Similar to the natural conditions, smoke development under relatively strong ventilation can also be subdivided into four regions. With the increase of ventilation velocity, the ceiling impact region, side wall impact region, and convergence region of two smoke streams move further downstream, indicating that the bifurcation phenomenon becomes more evident. A simple model is proposed based on theoretical analysis and experimental phenomenon to predict two characteristic lengths of smoke bifurcation flow: the offset distance of ceiling impact region and the length of low-temperature region. Both characteristic lengths increase with ventilation velocity and can be well correlated with the dimensionless ventilation velocity defined in Equation (2) ( V^′ ). The results of this work could provide references for both tunnel ventilation designers and fire science researchers.     

Effect of altitude on vertical temperature distribution and longitudinal smoke layer thickness in long tunnel fires

Based on large eddy simulation, a series of long tunnel fire experiments with different heat release rates (HRRs) and altitudes were carried out. The vertical temperature and thickness of fire smoke are studied. The simulation results show that the higher the altitude, the lower the flame temperature rise, while the change of smoke plume temperature rise is opposite. The movement of smoke in the tunnel can be divided into four regions, and the smoke layer thickness in the longitudinal direction of the tunnel corresponds to the latter three regions. The thickness in Region II increases along the longitudinal direction, the thickness in Region III is a constant value, and the thickness in Region IV increases along the longitudinal direction. Besides, the change of altitude only has an effect on the smoke layer thickness in Region IV. Then, by considering the altitude, HRR, and smoke layer thickness, and using dimensional analysis, an empirical formula for predicting the smoke layer thickness under the influence of altitude in Region IV was established.     

Experimental study of the combustion characteristics of methanol‐gasoline blends pool fires in a full‐scale tunnel

The combustion characteristics of methanol‐gasoline blends pool fires were studied in a series of full‐scale tunnel experiments conducted with different methanol and gasoline blends. The parameters were measured including the mass loss rate, the pool surface temperature, the fire plume centerline temperature, the ceiling temperature, the smoke layer temperature profile, the flame height, and the smoke layer interface height. The gasoline components were analyzed by GC‐MS. The effects of azeotropism on the combustion characteristics of the different blends were discussed. On the basis of the results of the fire plume centerline temperature, the ceiling temperature, and the flame height, it shows that the tunnel fire regime gradually switches from fuel controlled to ventilation controlled with increasing gasoline fractions in the blends. The fire plume can be divided into 3 regions by the fire plume centerline temperature for the different blends. The N‐percentage rule to determine the smoke layer interface height is found to be applicable for tunnel fires with different blends for N = 26.     

Experimental study on the effect of lateral concentrated smoke extraction on smoke stratification in the longitudinal ventilated tunnel

Smoke is the main cause of death in tunnel fires. It is one of the important measures to maintain smoke stratification in the early stage of tunnel fire. This article focused on experimentally studying the combined effect of lateral concentrated smoke extraction and longitudinal ventilation on the smoke stratification, which never be revealed before. The velocity of the smoke layer and air layer, vertical temperature distribution, and the flow patterns of the smoke were measured. It was found that the longitudinal ventilation and lateral concentrated smoke extraction would affect the flow of the smoke and change the shear velocity between the smoke layer and air layer, then, the patterns of the smoke layer will be affected. And the flow patterns with Froude (Fr) number can be classified into three categories: (a)Fr < 0.6 , with stable smoke stratification; (b) 0.6 < Fr < 0.85 , with a stable smoke stratification but the blurring interface; and (c) Fr > 0.85 , the smoke layer is completely unstable. The result can provide a reference for ventilation design of immersed tube tunnels.     

Experimental investigation on smoke spread characteristics and smoke layer height in tunnels

A series of experiments were carried out in a model‐scale tunnel with dimension of 6.0 m × 1.0 m × 0.7 m to investigate the smoke spread behaviors and the typical smoke layer height. Alcohol was employed as fuel, and the heat release rate was set to be 9.5, 18.4, 30.1, and 63.5 kW, respectively. The temperature profile in the tunnel was measured, and the buoyant flow stratification conditions were visualized by a laser sheet. The experiment results show that the N percentage rule would greatly influence by subjective factors. As the N (10, 20, 30) value increases, the smoke layer height also increases. The results calculated by the buoyancy frequency method were more accurate. Fan's prediction method (Fan WC, Wang QG, Jiang FH. Concise Guide of Fire Science. He Fei: University of Science and Technology of China Press; 1995.161 p.) does not accurately evaluate the smoke layer thickness in tunnel fire. An enhanced empirical formula for predicting the smoke layer thickness in the one‐dimensional horizontal spread stage was proposed. It is shown that the empirical formula could well predict the smoke layer thickness by comparing with the experimental data of previous studies.     

Experimental study of fire growth and ejected plume in a cross‐ventilation compartment under wind condition

In this study, a set of reduced‐scale experiments were conducted to study the influence of external wind on the fire growth and ejected plume in a compartment with two openings. The approaching wind velocity was set as 1.5 and 3.0 m/s, respectively. The temperatures in the fire compartment were also measured by thermocouple matrixes. The images of the projected flames from the opening and the fuel mass loss rate were recorded by digital video and electronic balance, respectively. It is observed that the wind with velocity of 1.5 m/s can reduce the combustion severity by decreasing the ventilation in the fire room and enhance the duration time of combustion. On the contrary, the wind with velocity of 3 m/s can promote the combustion severity by increasing the ventilation in the fire room and reduce the duration time of combustion. The theoretical analysis shows how the external wind that coupled with the thermal buoyance influence the ventilation of the compartment, and a critical velocity or a dimensional number are suggested to predict the ventilation of the fire room, which is believed to influence the compartment fire behavior greatly.     

Use of zone models on simulating compartmental fires with forced ventilation

Performance of three fire zone models BR12, CCFM.VENTS and CFAST in simulating forced ventilation fires with low heat release and high ventilation rates were studied experimentally. A fire chamber of length 4.0 m, width 3.0 m height 2.8 m with adjustable ventilation rates was used. Burning tests were carried out with wood cribs and methanol to study the preflashover stage of a compartmental fire and the effect of ventilation. The mass loss rate of fuel, temperature distribution of the compartment and the air intake rate were measured. The heat release rates of the fuel were calculated from the measured mass loss rate. The smoke temperature was used as the validation parameter. A scoring system is proposed to compare the results predicted by the three models. An empirical expression for calculating the smoke temperature is assessed. Lastly, the Computational Fluid Dynamics technique is also used for comparing the simulated fire environment.     

An experimental investigation on char pattern and depth at postflashover compartments using medium‐density fibreboard (MDF)

To determine the fire origins for postflashover compartments, the char pattern and depth are investigated. A set of experiments was carried out using large‐scale compartments made of medium‐density fibreboard. A liquefied petroleum gas burner was used as the ignition source to mimic the fire origin. The burner was set at different locations in different experiments. It is found that time to flashover, intermittent flame of gas burner and ventilation condition have effects on the char patterns. The ‘ventilation patterns’ are likely to confuse the fire investigators; therefore, it needs to be identified from the ‘flame patterns’. In general, the ventilation patterns at the floor would initiate directly from the compartment opening. CFD simulations is used to reflect the ventilation conditions during fires thus assisting the identification of ventilation patterns. For those cases with less distinguishable char patterns, the profiles of total leftover material thickness and char depth were used to determine the fire origin. The char layer and total thickness in the flame regions were found to be respectively deeper and thinner than the rest parts of the compartment. The ventilation condition also affects the char depth profile; therefore, it cannot be ignored from analysis. At the end, a strategy of fire origin determination is proposed. Copyright © 2014 John Wiley & Sons, Ltd.     

Evaluating methods for preventing smoke spread through ventilation systems using fire dynamics simulator

Fires in enclosures equipped with mechanical ventilation remain one of the key issues for fire safety assessment in multifamily homes and industries. Therefore, a wide variation of methods for preventing smoke spread through the ventilation system exist and are applied, in performance‐based designs. Through the use of the heating, ventilation and air conditioning (HVAC) model in the fire dynamics simulator, several different common and less common methods for preventing smoke spread in the ventilation system were tested. The effects on smoke spread with changing building leakage and fire growth rates were also investigated. The results were evaluated by determining the total soot spread from the fire room to other compartments connected to the ventilation system, as well as soot/thermal load on the fans and system in general. The maximum and average heat release rate was also of interest and hence compared between systems. It was found that, while many methods perform similar, a few proven methods, such as fire and smoke dampers, performed very well with very little smoke spread to the rest of the system. The study should be considered as an introduction to implementing a similar methodology in specific cases because different ventilations systems will present very different challenges and weaknesses. Copyright © 2016 John Wiley & Sons, Ltd.     

Visualization of room fire induced smoke movement and flow in a corridor

A study was conducted of the smoke and flow field in a corridor subject to a room fire. The study was conducted using a scale model of roughly 0.35 m in height. The effect of corridor-exit doorway width was recorded while the room doorway and fire-room temperature were maintained constant. Smoke was generated from cotton wads soaked with titanium tetrachloride which produces white particles of titanium dioxide. By this means, the smoke layer resulting from the room fire and the corridor flow characteristics were visualized. The results show the lowering interface of the corridor smoke layer with decreasing corridor-exit door width. Also a four-layer horizontal counter-current flow pattern was displayed and shown to result from a restriction (e.g. soffit) at the corridor exit. The mixing of the incoming cold flow and exiting hot flow at the corridor exit was observed to be shedding vortices swept into the cold floor jet. Results based on velocity measurements and smoke observations are presented for the corridor smoke layer height and doorway neutral-plane heights. The limitations of current predictive models are demonstrated for layer-heights and flow rates for the room and corridor experiments.     

Influence of multisource fire on temperature distribution and natural smoke exhaust effect in urban tunnels with a shaft

The combustion characteristics of multisource fire and single-source fire are quite different, and there is little research on the influence of multisource fire on the natural smoke extraction effect of shaft in urban tunnels. Therefore, in this article, the method of numerical simulation was used to study the influence of fire power and distance between two fire sources on the natural smoke extraction effect of shaft and the temperature distribution in tunnel in the case of multisource fire. Typical characteristics of smoke are analyzed, such as mass flow rate, temperature distribution, velocity vector, and CO concentration. The simulation results show that when there is a certain distance between the fire sources, the two flames are inclined and close to each other. The smoke temperature under the ceiling is higher under multiple fire sources than that under single fire source. In addition, when one of the fire sources is located at the downstream of the shaft, the smoke emission in the shaft is relatively high. As the distance between fire sources continues to increase, the smoke exhaust rate basically remains stable, and an empirical relationship between smoke exhaust rate and fire source location is established.     

Study on fire smoke flow characteristics in the ventilation network and linkage control system in coal mines

In coal mining, smoke flow from tunnel fires can easily cause a large number of deaths in the ventilation network. But the optimal smoke flow path control methods and automatic control system were lacked. In order to improve the efficiency of fire emergency rescue, the control mechanism and regional linkage control system for fire induced smoke flow in ventilation network was studied. Based on a ventilation system in coal mines, different fire scenarios for smoke flow were analysed using ventilation simulation software (VSS). Smoke flow control methods were simulated under different ventilation modes, a contrastive analysis was conducted for the respective effects and the optimal smoke flow path control methods were confirmed in different fire scenarios. A new type of ventilation facility, regional monitoring sub-stations and remote linkage control platforms were developed for smoke control. A reliability evaluation model for the control system was established by Bayesian network. The failure of the linkage control is 98.9%, the monitoring sub-station is 64.4%, the sub-station communication is 43.9%; thus, a double insurance of the control process must be realised. Since its application, the proposed regional linkage control system has been repeatedly tested through fire drills, and good results have been obtained.     

Smoke characteristics of coal-lined tunnel fires

Characteristics of smoke particulates generated from a coal fire in a ventilated model tunnel were investigated by laser optical transmission and by electron microscopy. Average particle diameter and mass concentration of the smoke were determined as a function of the temperature and stoichimoetry of the coal tunnel fire. Smoke particle sizes ranged from 0.2 to 0.9 μm, with larger particle sizes associated with higher smoke concentrations. These coal smoke data are relevant to several aspects of underground mine safety including the development and location of smoke detection instruments, the understanding of the fire (toxic fume) hazard, and the development of new fire protection and control techniques.     

电缆防火涂料阻火有效性试验

根据电缆隧道实际环境,建立电缆水平燃烧试验平台,研究不同火灾荷载和通风速度下,受防火涂料保护电缆延燃长度的变化规律。结果表明:一定风速条件下,电缆延燃长度随敷设宽度增加呈指数增长,可根据隧道内通风速度和电缆束宽度近似预测电缆延燃长度,从而为电缆隧道的防火设计提供依据。