Surface characterization of Al2O3–SiO2 supported NiMo catalysts: An effect of support composition

Al₂O₃–SiO₂ mixed oxide has been investigated as a support for hydrotreating catalyst with variation of its composition [Si/(Si + Al) = 0.06, 0.12, 0.31, 0.56, 0.78] and its interaction with the surface active metals (NiMo). The composition of support and surface species (NiMo) of catalysts were characterized by specific surface area, atomic absorption, SEM-EDX, XRD, temperature programmed reduction (TPR), Raman analysis, scanning electron microscopy (STEM) and transmission electron microscopy (TEM). Incorporation of SiO₂ in Al₂O₃ promotes a weak interaction between the active phases and particularly catalyst that predominated with SiO₂ content. The oxide and sulfided catalysts characterization indicated that the effect of support is responsible to form different catalytic sites. Crystallization of MoO₃ phases and a relatively longer crystal of MoS₂ in the sulfided catalyst were attributed to an increasing SiO₂ content in the support. The catalytic behavior of the NiMo supported catalysts is explained in terms of structural changes on the surface due to the support and active metal interactions. The activity of the different catalysts evaluated in the thiophene hydrodesulfurization reaction was higher for the catalyst having lower SiO₂ content in the support.     

Fischer–Tropsch synthesis over Re-promoted Co supported on Al2O3, SiO2 and TiO2: Effect of water

The activity and selectivity of rhenium promoted cobalt Fischer–Tropsch catalysts supported on Al₂O₃, TiO₂ and SiO₂ have been studied in a fixed-bed reactor at 483 K and 20 bar. Exposure of the catalysts to water added to the feed deactivates the Al₂O₃ supported catalyst, while the activity of the TiO₂ and SiO₂ supported catalysts increased. However, at high concentrations of water both the SiO₂ and TiO₂ supported catalyst deactivated. Common for all catalysts was an increase in C₅₊ selectivity and a decrease in the CH₄ selectivity by increasing the water partial pressure. The catalysts have been characterized by scanning transmission electron microscope (STEM), BET, H₂ chemisorption and X-ray diffraction (XRD).     

Ultrahigh temperature water gas shift catalysts to increase hydrogen yield from biomass gasification

Noble metal (Rh, Pt, Pd, Ir, Ru, and Ag) and Ni catalysts supported on CeO₂–Al₂O₃ were investigated for water gas shift reaction at ultrahigh temperatures. Pt/CeO₂–Al₂O₃ and Ru/CeO₂–Al₂O₃ demonstrated as the best catalysts in terms of activity, hydrogen yield and hydrogen selectivity. At 700 °C and steam to CO ratio of 5.2:1, Pt/CeO₂–Al₂O₃ converted 76.3% of CO with 94.7% of hydrogen selectivity. At the same conditions, the activity and hydrogen selectivity for Ru/CeO₂–Al₂O₃ were 63.9% and 85.6%, respectively. Both catalysts showed a good stability over 9 h of continuous operation. However, both catalysts showed slight deactivation during the test period. The study revealed that Pt/CeO₂–Al₂O₃ and Ru/CeO₂–Al₂O₃ were excellent ultrahigh temperature water gas shift catalysts, which can be coupled with biomass gasification in a downstream reactor.     

Catalytic performance of a novel ceramic-supported vanadium oxide catalyst for NO reduction with NH3

A novel TiO₂/Al₂O₃/cordierite honeycomb-supported V₂O₅–MoO₃–WO₃ monolithic catalyst was studied for the selective reduction of NO with NH₃. The effects of reaction temperature, space velocity, NH₃/NO ratio and oxygen content on SCR activity were evaluated. Two other V₂O₅–MoO₃–WO₃ monolithic catalysts supported on Al₂O₃/cordierite honeycomb or TiO₂/cordierite honeycomb support, two types of pellet catalysts supported on TiO₂/Al₂O₃ or Al₂O₃, as well as three types of pellet catalysts V₂O₅–MoO₃–WO₃–Al₂O₃ and V₂O₅–MoO₃–WO₃–TiO₂ were tested for comparison. The experiment results show that this catalyst has a higher catalytic activity for SCR with comparison to others. The results of characterization show, the preparation method of this catalyst can give rise to a higher BET surface area and pore volume, which is strongly related with the highly active performance of this catalyst. At the same time, the function of the combined carrier of TiO₂/Al₂O₃ cannot be excluded.     

Effect of pH in a sol–gel synthesis on the physicochemical properties of Pd–alumina three-way catalyst

The effect of pH during sol–gel synthesis on the structural and physicochemical properties of a Pd–Al₂O₃ three-way catalyst (TWC) prepared by the sol–gel method was investigated by using BET, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM) and solid state ²⁷Al MAS NMR. The Pd–Al₂O₃ catalyst prepared at pH=10 (Pd–Al₂O₃–B) showed a high activity in three-way catalytic reaction, a high dispersion of Pd, and large surface area and pore volume. A basic condition (pH=10) in the sol–gel process was essential for the preparation of highly dispersed palladium clusters on alumina gel. The formation of highly stable palladium oxide species in Pd–Al₂O₃–B that were not completely reduced at 423 K was ascribed to the strong interaction between Pd and oxygen in alumina texture, resulting in the formation of –Al–O–Pd bond.     

New materials as FCC active matrix components for maximizing diesel (light cycle oil, LCO) and minimizing its aromatic content

Different materials such as sepiolite (magnesiumsilicate), amorphous silico-alumino-phosphate (ASAPO) or other mixed oxides such as SiO₂–ZrO₂, or SiO₂–Al₂O₃–MgO, are studied as potential active matrix components of a FCC catalyst, with the final objective of maximizing the light cycle oil (LCO) yield while minimizing the aromatic content of this fraction. The physico-chemical characteristics of these materials as well as their hydrothermal stability play a decisive role in their catalytic behavior. The high surface area amorphous SAPO stands out presenting high selectivity to LCO while decreasing the aromatics content as compared to a commercial SiO₂–Al₂O₃ used as reference material. A formulation has been simulated using this material and, after equilibration, its catalytic behavior has been compared to that of a conventional FCC catalyst formulation.     

Catalytic removal of perchloroethylene (PCE) over supported chromium oxide catalysts

The oxidation of perchloroethylene (PCE) was investigated over chromium oxide catalysts supported on SiO₂, SiO₂–Al₂O₃, activated carbon, mordenite type zeolites, MgO, TiO₂ and Al₂O₃. Supported chromium oxide catalysts were more active than any other metal oxide catalysts including noble metal examined in the present study. PCE removal activity of chromium oxide catalysts mainly depended on the type of supports and the content of metal loaded on the catalyst surface. TiO₂ and Al₂O₃ containing high surface areas were effective for the high performance of PCE removal, since the formation of well dispersed Cr(VI) active reaction sites for the present reaction system, was enhanced even for the high Cr loading on the catalyst surface. CrO_x catalysts supported on TiO₂ and Al₂O₃ also exhibited stable PCE removal activity at a low feed concentration of PCE of 30 ppm up to 100 h at 350°C. However, significant catalyst deactivation was observed at high PCE concentration of 10 000 ppm. CrO_x/TiO₂ revealed stronger water tolerance than CrO_x/Al₂O₃ due to the surface hydrophobicity.     

Oxidative degradation properties of Co-based catalysts in the presence of ozone

Four series of cobalt-based catalysts, such as bare Co₃O₄ and CoO, CoO_x–CeO₂ mixed oxides, CoO_x supported over alumina and alumina–baria and CoMgAl and CoNiAl hydrotalcites have been synthesized and investigated for the oxidative degradation of phenol in the presence of ozone. Characterizations were obtained by several techniques in order to investigate the nature of cobalt species and their morphological properties, depending on the system. Analyses by XRD, BET, TPR, UV–visible diffuse reflectance spectroscopy and TG/DT were performed.

The CoNiAl hydrotalcite exhibits, after 4 h of reaction, the highest phenol ozonation activity followed by Co(3 wt%)/Al₂O₃–BaO and CoMgAl. The samples Co(1 wt%)/Al₂O₃–BaO and Co(1 and 3 wt%)/Al₂O₃ show a comparable medium activity, while the oxidation properties of bare oxides Co₃O₄, CoO and CoO_x–CeO₂ are really low. Leaching of cobalt ions in the water solution was detected during the reaction, the amount varied depending on the nature of catalysts. A massive release was observed for the CoMgAl and CoNiAl hydrotalcites, while cobalt catalysts over alumina and alumina–baria look much more stable. The recycle of CoO_x/Al₂O₃ and CoO_x/Al₂O₃–BaO was studied by performing three consecutive cycles in the phenol oxidation. Because of the potential interest of the cobalt-supported catalysts in the ozonation process, the oxidative degradation of naphtol blue black was also investigated.

On the basis of TPR and UV–visible results it appears that highly dispersed Co²⁺ ions especially present over Co(3 wt%)/Al₂O₃–BaO are the main active sites for phenol and naphtol blue black oxidative degradation by ozone.     

K-, CeO2-, and Mn-promoted Ni/Al2O3 catalysts for stable CO2 reforming of methane

Reforming of methane with carbon dioxide into syngas over Ni/γ-Al₂O₃ catalysts modified by potassium, MnO and CeO₂ was studied. The catalysts were prepared by impregnation technique and were characterized by N₂ adsorption/desorption isotherm, BET surface area, pore volume, and BJH pore size distribution measurements, and by X-ray diffraction and scanning electron microscopy. The performance of these catalysts was evaluated by conducting the reforming reaction in a fixed bed reactor. The coke content of the catalysts was determined by oxidation conducted in a thermo-gravimetric analyzer. Incorporation of potassium and CeO₂ (or MnO) onto the catalyst significantly reduced the coke formation without significantly affecting the methane conversion and hydrogen yield. The stability and the lower amount of coking on promoted catalysts were attributed to partial coverage of the surface of nickel by patches of promoters and to their increased CO₂ adsorption, forming a surface reactive carbonate species. Addition of CeO₂ or MnO reduced the particle size of nickel, thus increasing Ni dispersion. For Ni–K/CeO₂–Al₂O₃ catalysts, the improved stability was further attributed to the oxidative properties of CeO₂. Results of the investigation suggest that stable Ni/Al₂O₃ catalysts for the carbon dioxide reforming of methane can be prepared by addition of both potassium and CeO₂ (or MnO) as promoters.     

Hydrodesulfurization of dibenzothiophenes over molybdenum catalyst supported on TiO2–Al2O3

Composite types of TiO₂–Al₂O₃ supports, which are γ-aluminas coated by titania, have been prepared by chemical vapor deposition (CVD), using TiCl₄ as a precursor. Then supported molybdenum catalysts have been prepared by an impregnation method. As supports, we employed γ-alumina, anatase types of titania, and composite types of TiO₂–Al₂O₃ with different loadings of TiO₂. We studied the conversion of Mo from oxidic to sulfidic state through sulfurization by X-ray photoelectron spectroscopy (XPS). The obtained spectra unambiguously revealed the higher reducibility from oxidic to sulfidic molybdenum species on the TiO₂ and TiO₂–Al₂O₃ supports compared to that on the Al₂O₃ support. Higher TiO₂ loadings of the TiO₂–Al₂O₃ composite support led to higher reducibility for molybdenum species. Furthermore, the catalytic behavior of supported molybdenum catalysts has been investigated for hydrodesulfurization (HDS) of dibenzothiophene (DBT) and methyl-substituted DBT derivatives. The conversion over the TiO₂–Al₂O₃ supported Mo catalysts, in particular for the 4,6-dimethyl-DBT, is much higher than that obtained over Al₂O₃ supported Mo catalyst. The ratio of the corresponding cyclohexylbenzene (CHB)/biphenyl (BP) derivatives is increased over the Mo/TiO₂–Al₂O₃. This indicates that the prehydrogenation of an aromatic ring plays an important role in the HDS of DBT derivatives over TiO₂–Al₂O₃ supported catalysts.     

Tailoring of alumina surfaces as supports for NiMo sulfide catalysts in the ultra deep hydrodesulfurization of gas oil: case study of TiO2-coated alumina prepared by chemical vapor deposition technique

The present paper gives a detailed review of the different studies under investigation in our laboratory concerning the use of TiO₂ and TiO₂–Al₂O₃ composites prepared by chemical vapor deposition (CVD) as support for sulfide catalysts in the HDS of dibenzothiophene (DBT) derivatives. The supports investigated here are: TiO₂ (from Degussa, 50 m²/g), Al₂O₃ (Nikki, 186 m²/g) and TiO₂–Al₂O₃ supports prepared by CVD of TiCl₄ on alumina. Using several characterization techniques, we have demonstrated that the support composite presents a high dispersion of TiO₂ over γ-Al₂O₃ without forming precipitates up to ca. 11 wt.% loading. Moreover, the textural properties of the support composite are comparable to those of alumina. XPS investigations of Mo and NiMo catalysts supported on the different carriers show that Mo-oxide species exhibit a higher degree of sulfidation on the surface of TiO₂ and TiO₂–Al₂O₃ than on alumina. The HDS tests of 4,6-DMDBT under mild operating conditions (573 K, 3 MPa) show that sulfide catalysts supported on the composite support (ca. 11 wt.%) are more active than those supported on to TiO₂ or Al₂O₃. This higher HDS catalytic activity is attributed to the promotion of the hydrodesulfurization pathway, whereby the pre-hydrogenation of one of the aromatic rings adjacent to the thiophenic one may reduce the steric hindrance caused by the two methyl groups adjacent to the sulfur atom during the C–S bond cleavage.     

Study on the supported Cu-based catalysts for the low-temperature water–gas shift reaction

This paper presents a study on the influence of support (Al₂O₃, MgO, SiO₂-Al₂O₃, SiO₂-MgO, β-zeolite, and CeO₂) of Cu-ZnO catalysts for the low-temperature water–gas shift reaction. Supported Cu-ZnO catalysts were prepared by the conventional impregnation method, followed by the H₂ reduction. The activity of Cu-ZnO catalysts for the water–gas shift (WGS) reaction was largely influenced by the kind of support; Cu-ZnO catalysts supported on Al₂O₃, MgO, and CeO₂ showed high activity, while those on SiO₂-Al₂O₃, SiO₂-MgO and β-zeolite showed less activity in the temperature range 423–523 K. XRD analysis demonstrated that the copper species were highly dispersed on the supports used in the present study, except for a MgO support. TPR results of a series of supported CuO-ZnO catalysts suggest that the reducibility of CuO is one of the important factors controlling the activity of the WGS reaction over the supported catalysts.     

Role of CeO2 in Ni/CeO2–Al2O3 catalysts for carbon dioxide reforming of methane

Ni catalysts supported on γ-Al₂O₃, CeO₂ and CeO₂–Al₂O₃ systems were tested for catalytic CO₂ reforming of methane into synthesis gas. Ni/CeO₂–Al₂O₃ catalysts showed much better catalytic performance than either CeO₂- or γ-Al₂O₃-supported Ni catalysts. CeO₂ as a support for Ni catalysts produced a strong metal–support interaction (SMSI), which reduced the catalytic activity and carbon deposition. However, CeO₂ had positive effect on catalytic activity, stability, and carbon suppression when used as a promoter in Ni/γ-Al₂O₃ catalysts for this reaction. A weight loading of 1–5 wt% CeO₂ was found to be the optimum. Ni catalysts with CeO₂ promoters reduced the chemical interaction between nickel and support, resulting in an increase in reducibility and stronger dispersion of nickel. The stability and less coking on CeO₂-promoted catalysts are attributed to the oxidative properties of CeO₂.     

Synthesis, characterization and catalytic properties of NiMo/Al2O3–MCM-41 catalyst for dibenzothiophene hydrodesulfurization

Ni–Mo/Al₂O₃–MCM-41 supported catalysts have been investigated for modification of MCM-41 by using sol–gel alumina incorporation method. Different catalysts were synthesized with variation of Si/Al molar ratios of 10, 50, 100 and 200. High specific surface area ordered meso-porous solid (MCM-41) was synthesized by using organic template method. In order to modify the low acidity of silica solid, the surface of MCM-41 was modified by incorporation of alumina. The surface acidity of solids modified significantly with variation of alumina content in the supports. The sol–gel method of alumina incorporation was used, which does not modify extensively the pore characteristics of MCM-41 material during the preparation of Al₂O₃–MCM-41. The X-ray diffraction intensities indicated that alumina as well as MCM-41 were present in the synthesized supports. Additionally, the hydrothermal stability of the Al₂O₃–MCM-41 materials was maintained up to 873 K using sever conditions like 100% water vapor stream. The catalytic activity of the catalysts was tested in the hydrodesulfurization (HDS) of dibenzothiophene (DBT). Selectivity was oriented mainly to the production of biphenyl (BP) and for high Si/Al ratios toward cyclohexylbenzene (CHB) and showed a higher conversion and better selectivity to hydrogenation (cyclohexylbenzene).     

Synthesis, characterization and evaluation of NiMo/SiO2–Al2O3 catalysts prepared by the pH-swing method

NiMo/(X)SiO₂–Al₂O₃ catalysts were synthesized with various SiO₂ contents (X = 0, 10, 25 and 50 wt%) using the pH-swing method. In order to find the optimum SiO₂ content, the catalysts were evaluated in the hydrodesulfurization of 4,6-DMDBT, hydrogenation of naphthalene and hydrodenitrogenation of carbazole. Kinetic parameters of Langmuir–Hinshelwood type equations for all the reaction systems were estimated. FTIR analysis of CO adsorption for the sulfided catalysts shows that the amount of coordinatively unsaturated Mo sites promoted by nickel (CUS-NiMoS) follows the order NiMo/10ASA > NiMo/25ASA > NiMo/0ASA. This tendency agrees with the results obtained in catalytic activity.     

Ethylene dimerization over NiSO4 supported on Fe2O3-promoted ZrO2 catalyst

The NiSO₄ supported on Fe₂O₃-promoted ZrO₂ catalysts were prepared by the impregnation method. Fe₂O₃-promoted ZrO₂ was prepared by the coprecipitation method using a mixed aqueous solution of zirconium oxychloride and iron nitrate solution followed by adding an aqueous ammonia solution. No diffraction line of nickel sulfate was observed up to 20 wt.%, indicating good dispersion of nickel sulfate on the surface of Fe₂O₃–ZrO₂. The addition of nickel sulfate (or Fe₂O₃) to ZrO₂ shifted the phase transition of ZrO₂ (from amorphous to tetragonal) to higher temperatures because of the interaction between nickel sulfate (or Fe₂O₃) and ZrO₂. 15-NiSO₄/5-Fe₂O₃–ZrO₂ containing 15 wt.% NiSO₄ and 5 mol% Fe₂O₃, and calcined at 500 °C exhibited a maximum catalytic activity for ethylene dimerization. NiSO₄/Fe₂O₃–ZrO₂ catalysts was very effective for ethylene dimerization even at room temperature, but Fe₂O₃–ZrO₂ without NiSO₄ did not exhibit any catalytic activity at all. The catalytic activities were correlated with the acidity of catalysts measured by the ammonia chemisorption method. The addition of Fe₂O₃ up to 5 mol% enhanced the acidity, surface area, thermal property, and catalytic activities of catalysts gradually, due to the interaction between Fe₂O₃ and ZrO₂ and due to consequent formation of Fe–O–Zr bond.     

Design of 7 wt.% Y2O3–ZrO2/mullite plasma-sprayed composite coatings for increased creep resistance

Plasma-sprayed stand-alone coatings of 7 wt.% Y₂O₃–ZrO₂ (YSZ), nominally 74 wt.% Al₂O₃–26 wt.% SiO₂ mullite, and a 46:54 volume ratio composite of YSZ to mullite were examined using X-ray diffraction, dilatometry, and compression creep. X-ray diffraction and dilatometer results showed that the as-sprayed predominantly amorphous mullite crystallized at 970 °C. Creep tests were conducted on all three coating types in the as-sprayed condition at stresses from 40 to 80 MPa and temperatures of 1000–1200 °C. The primary deformation mechanism in coatings made from all three materials was stress-assisted densification of the porous coating. While the creep behavior of YSZ/mullite composite specimens was between that of pure YSZ and pure mullite specimens for all combinations of temperature and stress tested, the creep response of the composite was more similar to that of pure mullite for all cases tested, consistent with mullite being the continuous phase in the composite.     

ZrO2/SiO2- and La2O3/Al2O3-supported platinum catalysts for CH4/CO2 reforming

Surface-phase ZrO₂ on SiO₂ (SZrOs) and surface-phase La₂O₃ on Al₂O₃ (SLaOs) were prepared with various loadings of ZrO₂ and La₂O₃, characterized and used as supports for preparing Pt/SZrOs and Pt/SLaOs catalysts. CH₄/CO₂ reforming over the Pt/SZrOs and Pt/SLaOs catalysts was examined and compared with Pt/Al₂O₃ and Pt/SiO₂ catalysts. CO₂ or CH₄ pulse reaction/adsorption analysis was employed to elucidate the effects of these surface-phase oxides.

The zirconia can be homogeneously dispersed on SiO₂ to form a stable surface-phase oxide. The lanthana cannot be spread well on Al₂O₃, but it forms a stable amorphous oxide with Al₂O₃. The Pt/SZrOs and Pt/SLaOs catalysts showed higher steady activity than did Pt/SiO₂ and Pt/Al₂O₃ by a factor of three to four. The Pt/SZrOs and Pt/SLaOs catalysts were also much more stable than the Pt/SiO₂ and Pt/Al₂O₃ catalysts for long stream time and for reforming temperatures above 700 °C. These findings were attributed to the activation of CO₂ adsorbed on the basic sites of SZrOs and SLaOs.     

Improvement of catalytic activity and sulfur-resistance of Ag/TiO2–Al2O3 for NO reduction with propene under lean burn conditions

Ag-based catalysts supported on various metal oxides, Al₂O₃, TiO₂, and TiO₂–Al₂O₃, were prepared by the sol–gel method. The effect of SO₂ on catalytic activity was investigated for NO reduction with propene under lean burn condition. The results showed the catalytic activities were greatly enhanced on Ag/TiO₂–Al₂O₃ in comparison to Ag/Al₂O₃ and Ag/TiO₂, especially in the low temperature region. Application of different characterization techniques revealed that the activity enhancement was correlated with the properties of the support material. Silver was highly dispersed over the amorphous system of TiO₂–Al₂O₃. NO₃⁻ rather than NO₂⁻ or NOx reacted with the carboxylate species to form CN or NCO. NO₂ was the predominant desorption species in the temperature programmed desorption (TPD) of NO on Ag/TiO₂–Al₂O₃. More amount of formate (HCOO⁻) and CN were generated on the Ag/TiO₂–Al₂O₃ catalyst than the Ag/Al₂O₃ catalyst, due to an increased number of Lewis acid sites. Sulfate species, resulted from SO₂ oxidation, played dual roles on catalytic activity. On aged samples, the slow decomposition of accumulated sulfate species on catalyst surface led to poor NO conversion due to the blockage of these species on active sites. On the other hand, catalytic activity was greatly enhanced in the low temperature region because of the enhanced intensity of Lewis acid site caused by the adsorbed sulfate species. The rate of sulfate accumulation on the Ag/TiO₂–Al₂O₃ system was relatively slow. As a consequence, the system showed superior capability for selective adsorption of NO and SO₂ toleration to the Ag/Al₂O₃ catalyst.     

Promoting effect of water vapor on catalytic oxidation of methane over cobalt/manganese mixed oxides

Methane oxidation was conducted in a fixed bed quartz tubular reactor on a series of mixed oxides of cobalt/manganese prepared by a sol–gel method. A unique promoting effect of water vapor on methane conversion was observed for the first time on these cobalt/manganese mixed oxides calcined at 450 or 600 °C. However, these mixed catalysts lost their catalytic activities after being calcined at 850 °C. The catalytic activity of methane oxidation was significantly improved by supporting the cobalt/manganese mixed species onto the high surface area SiO₂ or Al₂O₃–SiO₂ materials. It was noteworthy that the water enhancement effect was retained on these supported catalysts.