磁控溅射MgxZn1-xO薄膜的结构与光学性能研究

利用射频磁控溅射技术在玻璃衬底上沉积了MgxZn1-xO(x=0～0.2)薄膜.采用X射线衍射仪、紫外-可见光分光光度计和荧光光谱仪研究了Mg掺杂量对MgxZn1-xO薄膜结构与光学性能的影响.XRD图谱表明,MgxZn1-xO薄膜均为六角纤锌矿结构,并且呈现出C轴择优生长特性,当x>0.1时薄膜出现(100)面衍射峰,薄膜的c轴择优生长特性减弱,随着x值的增加,晶格常数c逐渐减小.紫外可见光透射光谱表明,Mg的掺入提高了薄膜在可见光范围内的透过率,同时使薄膜的禁带宽度增大.PL谱分析显示,Mg的掺入使薄膜的紫外发射峰和蓝光发射带发生蓝移,当x=0.1时近带边发射峰与杂质发射的强度比值最高.     

溅射法生长 MgxZn1- xO薄膜的结构和光学特性

用射频磁控溅射法在不同衬底上制备出了MgxZn1-xO薄膜。X射线衍射(XRD)和原子力显微镜(AFM)研究结果表明,薄膜为六角纤锌矿结构,具有(002)方向择优取向;随氧分压增加,(002)衍射峰的角度变大,表征薄膜表面粗糙程度的方均根粗糙度减小。室温光致发光谱中有多个紫外及可见光致发光峰,其中344nm发光峰应来源于近带边发射。室温透射谱表明薄膜在可见光区具有极高的透过率,薄膜的吸收边位于340nm附近,进而估算出Mg、Zn1-xO薄膜的带隙宽度为3．59eV,与光致发光结果一致。     

立方MgxZn1-xO晶体薄膜的制备和性能

采用低温物理沉积技术在二氧化硅衬底(SiO2/Si(100))和石英玻璃上生长出了MgxZn1-xO(x＞0.5)晶体薄膜,并用扫描电镜(SEM)、原子力显微镜(AFM)、X射线衍射(XRD)图谱和紫外-可见光透射光谱对其进行了表征.结果表明,在SiO2/Si(100)和石英玻璃衬底上沉积的MgxZn1-xO(x＞0.5)晶体薄膜表面平整,均呈立方结构,且具有高度的(001)择优取向.立方MgxZn1-xO薄膜具有从紫外到近红外波段良好的透明性,折射率为1.7～1.8,随着波长的增大或Mg组分的增大而降低.     

超声喷雾热解法制备MgxZn1-xO薄膜及其性能研究

采用超声喷雾热解法在石英玻璃衬底上生长出不同组分的宽禁带MgxZn1-xO薄膜(z=0、0.08、0.16、0.25).通过X射线衍射(XRD)、扫描电子显微镜(SEM)和分光光度计等分析测试手段对MgxZn1-xO薄膜的晶体结构、透光性及禁带宽度进行了研究.结果表明,随着Mg含量的增加,MgxZn1-xO薄膜仍然保持着ZnO的纤锌矿结构,没有生成MgO相,Mg可以有效地溶入ZnO的晶格中.MgxZn1-xO薄膜具有良好的透光性,在可见波段的光透过率达85%以上;此外,随着Mg含量的增加,MgxZn1-xO薄膜的吸收边出现蓝移现象,禁带宽度从3.30eV增大到3.54eV.     

立方相MgxZn1-xO纳米晶体薄膜的物理特性

介绍了在Si衬底和石英玻璃衬底上生长的立方相MgxZn1-xO(0.55≤x≤1)晶体薄膜的物理特性,AFM和XRD等微结构特性表征显示了良好的表面形貌和高度的(111)取向生长特性.采用Manifacier方法,根据透射光谱中的干涉峰,计算得到立方相MgxZn1-xO薄膜的折射率.与已报道的六方相MgxZn1-xO(0≤x≤0.5)薄膜的折射率相类似,在400～800nm的可见光区域,不同Mg含量的立方相MgxZn1-xO薄膜,其折射率随入射波长的色散关系遵循一阶Sellmeier方程.对给定400nm的入射光波长,当薄膜中的Mg含量由55%增至100%时,其折射率由1.89衰减至1.73.     

溶胶-凝胶法制备MgxZn1-xO薄膜及性能研究

采用溶胶-凝胶法在石英玻璃片衬底上制备了Mg2+掺杂的ZnO(MgxZn1-xO)薄膜,研究了Mg2+掺杂对ZnO薄膜结构和紫外透过率的影响;在氧化物薄膜上真空蒸镀了Al叉指电极,制得紫外原型探测器件,测试了I-Ⅴ特性.结果表明,Mg2+掺杂后,MgxZn1-xO薄膜为纤锌矿结构,随着x值增加,晶格常数c逐渐减少,α逐渐增大,Mg2+掺杂抑制了(002)晶面的生长;紫外透过光谱表明,Mg2+掺杂后吸收边发生蓝移,可提高ZnO薄膜的禁带宽度;I-Ⅴ特性曲线表明,正向偏压下探测器的暗电流和光照电流随外加偏压呈线性增长,但光照电流与暗电流的差别较大.     

Si(111)衬底上生长的立方MgxZn1-x晶体薄膜

在国际上第一次采用电子束反应蒸发法在Si(111)衬底上生长了MgxZn1-xO晶体薄膜。能量色散X射线(EDX)特征能谱及X射线衍射(XRD)分析表明薄膜呈立方结构，薄膜的晶面取向依赖于生长温度，在200℃温度下生长得到高度(200)取向的立方MgxZn1-xO薄膜，温度过高时得到多晶薄膜。对高度(200)取向的立方MgxZn1-xO薄膜的光荧光激发谱(PLE)分析表明其光学带隙为4．20eV，相对于MgO的带隙红移量为3．50eV。XRD分析还表明立方MgxZn1-xO薄膜与MgO衬底之间的晶格失配仅为0．16％。这使得高质量立方MgxZn1-xO多量子阱材料的制备成为可能。     

Si(111)衬底上生长的立方MgxZn1-xO晶体薄膜

在国际上第一次采用电子束反应蒸发法在Si(111)衬底上生长了MgxZn1-xO晶体薄膜.能量色散X射线(EDX)特征能谱及X射线衍射(XRD)分析表明薄膜呈立方结构,薄膜的晶面取向依赖于生长温度,在200C温度下生长得到高度(200)取向的立方MgxZn1-xO薄膜,温度过高时得到多晶薄膜.对高度(200)取向的立方MgxZn1-xO薄膜的光荧光激发谱(PLE)分析表明其光学带隙为4.20eV,相对于MgO的带隙红移量为3.50eV.XRD分析还表明立方MgxZn1-xO薄膜与MgO衬底之间的晶格失配仅为0.16%.这使得高质量立方MgxZn1-xO/MgO多量子阱材料的制备成为可能.     

Mg掺杂对ZnO纳米纤维发光性能的影响

采用静电纺丝法在Si基底上制备了不同Mg掺杂浓度的ZnO纳米纤维膜,利用扫描电子显微镜(SEM)、X射线衍射(XRD)、X射线光电子能谱(XPS)、光致发光(PL)等手段对不同Mg掺杂浓度ZnO纳米纤维膜的表面形貌、晶体结构、化学成分、发光性能进行研究。SEM结果表明MgxZn1-xO纳米纤维的直径在50~300nm。XRD结果表明在Mg掺杂浓度低于15%(x=0.15)时,晶体呈现ZnO六角纤锌矿结构,当掺杂浓度达到20%(x=0.2)时,晶体出现MgO的分相。XPS结果表明Mg已成功掺入到ZnO纳米纤维中。PL谱表明MgxZn1-xO纤维膜具有较强的紫外发射,而可见发射几乎观察不到,随着Mg掺杂浓度的增加,紫外发光峰明显蓝移且发光强度增加。     

Zn1-xCuxO薄膜的结构和光学性质

采用CS-400型射频磁控溅射仪在Si(111)和石英基底上成功的制备了Zn1-xCuxO薄膜,薄膜的晶体取向和表面形貌用X射线衍射(XRD)仪和扫描电子显微镜 (SEM)进行测量.利用紫外-可见光(UV-vis)分光光度计来测量基片为石英的Zn1-xCuxO薄膜的透射光谱.实验表明,采用射频磁控溅射制备的掺Cu氧化锌薄膜具有(002)峰的择优取向.随着Cu掺入量的增加样品成膜质量降低,禁带宽度减小,透射率下降.     

Insertion of triangulated surfaces into a meccano tetrahedral discretization by means of mesh refinement and optimization procedures

In this paper, we present a new method for inserting several triangulated surfaces into an existing tetrahedral mesh generated by the meccano method. The result is a conformal mesh where each inserted surface is approximated by a set of faces of the final tetrahedral mesh. First, the tetrahedral mesh is refined around the inserted surfaces to capture their geometric features. Second, each immersed surface is approximated by a set of faces from the tetrahedral mesh. Third, following a novel approach, the nodes of the approximated surfaces are mapped to the corresponding immersed surface. Fourth, we untangle and smooth the mesh by optimizing a regularized shape distortion measure for tetrahedral elements in which we move all the nodes of the mesh, restricting the movement of the edge and surface nodes along the corresponding entity they belong to. The refining process allows approximating the immersed surface for any initial meccano tetrahedral mesh. Moreover, the proposed projection method avoids computational expensive geometric projections. Finally, the applied simultaneous untangling and smoothing process delivers a high‐quality mesh and ensures that the immersed surfaces are interpolated. Several examples are presented to assess the properties of the proposed method.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Flow calorimeter for enthalpy increment measurements on condensed gases

A flow calorimeter for enthalpy increment measurements on condensed gases is presented. A better knowledge of the properties of the liquefied natural gas is needed, and therefore a liquid loop has been designed for our flow calorimeter. The fluid loop in the calorimeter is designed in order to avoid the two-phase region, since two phases would give compositional disturbances in the measurements. The avoidance of the two-phase region is made possible by increasing the pressure of the test fluid after the measurement section, then heating the fluid at super-critical pressure past the critical point. Finally, the fluid is throttled to the low-pressure gas state at the inlet condition of the compressor that circulates the fluid. To perform the pressure increase, a new cryogenic pump has been designed. To evaluate the new equipment, measurements were taken on liquid ethane over the temperature range 146–256 K at pressure between 0.9 and 5.1 MPa.     

From Industry 4.0 to Research 4.0. Development of High Performance Fibers in the Light of Digitization

We associate a variety of innovations with the term ＂Industry 4.0＂. The pioneer of many 4.0 modifications forms the basisfor the trend towards the integrated di...     

Refrigerators Enter a New Era of Health Preservation Frestech initiates the establishment of China's first standard for household sterilization refrigerators

On November 30, 2007, the China Association for Standardization (CAS) held a press conference at Beijing Diaoyutai State Guest House. Leaders from the China Household Electric Appliance Research Institute, the China Household Electric Appliance Association, and the China Consumers' Association attended and made speeches.……     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

Roman iron and steel: A review

ABSTRACT

The production of ferrous metal increased during the Roman Late Republican period, Principate and Empire. The direct bloomery process was used to extract the metal from its ores using slag-tapping and slag-pit furnaces. The fuel was charcoal and an air blast was introduced by bellows-operated tuyères. Iron formed as a bloom, often as a spongy mass of metal, which contained impurities from the smelting process, including unreacted ore, fuel, slag and fragments from the furnace walls, while the metal was often inhomogeneous with varied carbon contents. Blooms were either smithed directly into bars or ingots or they were broken up, which also allowed the removal of gross impurities and a selection of pieces with similar properties to be made. These could then be forge-welded together and formed into characteristically shaped ingots. Making steel in the furnace seems to have been achieved: it depended on the ore and the furnace and conditions within it. Surface carburization was also carried out. Iron and steel were used extensively in construction and for tools and weapons. Fire welding was often used to add pieces of steel to make the edges of tools and weapons, which could be heat-treated by quenching to harden them.     

A study of centrifugal cast high boron high speed steel

In the present study a high‐boron high speed steel (HSS) roll material was designed. Many expensive alloy elements have been substituted by cheap boron alloy, and high‐boron high speed steel roll has been manufactured by centrifugal casting method. The microstructures, mechanical properties and wear resistance of centrifugal casting high‐boron high speed steel roll have been investigated by optical microscopy (OM), scanning electron microscopy (SEM), and X‐ray diffraction (XRD) analysis, hardness test, impact test and wear test. The results indicated that the solidification microstructures of high‐boron high speed steel roll consisted of M₂(B,C), (W,Mo)₂(B,C), M₃(B,C), M₂₃(B,C)₆ type borocarbides and martensite, a small amount of retained austenite. Borocarbides were continuously distributed over the grain boundary. After quenching from 1050 °C, local broken network appeared in partial borocarbides, and fine secondary borocarbide precipitated from the matrix. After tempering from 525 °C, the amount of precipitated borocarbide increased significantly. After heat treatment, the hardness of high‐boron high speed steel roll excelled 60 HRC, and its impact toughness excelled 8.0 J/cm². The single groove steel rolling amount of high‐boron high speed steel rolls increases by 500% than that of bainite cast iron roll, when the rolls are used in K₁ mill housing of bar mill.     

Thixotropy of Systems with Shear Thinning and Plastic Flow Behavior

The definition of the thixotropy is a decrease in viscosity with time in shear and a subsequent recovery of viscosity after the shear deformation is removed.We ...