Synthesis and characterization of fluorine and nitrile containing polyimides

A series of polyimides were synthesized from new diamine, Bis [4,4′‐amino‐5,5′ trifluoromethyl phenoxy‐(hexafluoro isopropylidine) phenoxy phenyl] benzonitrile [BATFB] and various aromatic tetracarboxylic anhydrides by thermal and chemical imidization routes. The BATFB was synthesized in two steps by nucleophilic displacement reaction of 2,6‐dichloro benzonitrile, 4,4′‐(hexafluoro isopropylidine) diphenol and 2‐amino‐5‐fluoro benzotrifluoride in the presence of anhydrous potassium carbonate in N,N′‐dimethyl acetamide (DMAc) and the structure was confirmed by FTIR spectroscopy and CHNSO analyzer. The polymers were characterized by FTIR spectroscopy and thermal analysis were performed by differential scanning calorimetry and thermogravimetric analysis methods. The prepared polyimides had glass transition temperatures between 230 and 290°C and their 10% weight loss were recorded in the range 550–590°C in N₂ atmosphere. Majority of polymers are found to be soluble in most of the organic solvents such as DMSO, DMF, DMAc, m‐cresol, and THF even at room temperature and few becomes soluble on heating. The prepared polyimides showed water uptake values 0.34–0.54 wt % at room temperature. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3455–3461, 2006     

Molecular weight controlled poly(amic acid) resins end‐capped with phenylethynyl groups for manufacturing advanced polyimide films

To investigate the effect of reactive end‐capping groups on film‐forming quality and processability, a series of molecular weight‐controlled aromatic poly(amic acid) (PAA) resins functionalized with phenylethynyl end groups were prepared via the polycondensation of 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (BPDA), para ‐phenylenediamine (PDA), and 4‐phenylethynyl phthalic anhydride (PEPA) served as molecular‐weight‐controlling and reactive end capping agent. The PAA resins with relatively high concentrations endow enhanced wetting/spreading ability to form PAA gel films by solution‐cast method which were thermally converted to the fully‐cured polyimide (PI) films. The mechanical and thermal properties of PI films were investigated as a function of PAA molecular weights (M_n ) and thermal‐curing parameters. Mechanical property, dimensional stability and heat resistance of the fully‐cured PI films with PAA M_n > 20 ×10³ g mol^?1 are found to be better than that of their unreactive phthalic end‐capped counterparts. The covalent incorporation of chain‐extension structures in the backbones, induced by thermal curing of phenylethynyl groups, might facilitate yielding a higher degree of polymer chain order and consequently improved resistance strength and elongation at break to tensile plastic deformation. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 45168.     

Synthesis and characterization of poly(acrylate amic acid) and its application as negative‐tone photosensitive polyimides

The dianhydride monomer 3,3′,4,4′‐benzophenone tetracarboxylic acid dianhydride and two diamine monomers, 4,4′‐diamino‐3,3′‐biphenyldiol (HAB) and 2,4‐diaminophenol dihydrochloride (DAP), were used to synthesize a series of poly(hydroxyl amic acid). Further functionalization by grafting acrylate groups yields the corresponding poly(acrylate amic acid) that underwent a crosslinking reaction on exposure to UV‐light and was used as a negative‐tone photosensitive polyimide (PSPI). The analysis of chemical composition and molecular weight of these poly(amic acid)s determined by nuclear magnetic resonance (NMR) spectroscopy, Fourier transform infrared spectroscopy, and gel permeation chromatography revealed that the molecular weight of the poly(hydroxyl amic acid) increased with the molar content of HAB in the feedstock, because HAB exhibited higher polymerization reactivity than DAP. Moreover, the degree of grafting acrylate groups onto poly(hydroxyl amic acid) was determined by ¹H‐NMR spectroscopy. The photoresist was formulated by adding 2‐benzyl‐2‐N,N‐dimethylamino‐1‐(4‐morpholinophenyl) butanone (IRG369) and isopropylthioxanthone as a photoinitiator, tetra(ethylene glycol) diacrylate as a crosslinker, and tribromomethyl phenyl sulfone as a photosensitizer. The PSPI precursor exhibited a photosensitivity of 200 mJ/cm² and a contrast of 1.78. A pattern with a resolution of 10 μm was observed in an optical micrograph after thermal imidization at 300°C. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Preparation and characterization of transparent poly(methyl methacrylate)/Na+‐MMT nanocomposite films by solution casting

Films of poly(methyl methacrylate) (PMMA)/sodium montmorillonite (Na⁺‐MMT) nanocomposites have been successfully prepared utilizing Na⁺‐MMT by N,N‐dimethylformamide solution casting. The nanocomposite films show high transparency, enhanced thermal resistance, and mechanical properties in comparison with the neat polymer film. The transparency of the films was investigated by UV‐vis spectra. The exfoliated dispersion of Na⁺‐MMT platelets in nanocomposites were investigated by X‐ray diffraction and transmission electron microscopy. The enhanced thermal resistance and mechanical properties of PMMA were studied by thermal gravimetric analysis and dynamic mechanical analysis, respectively. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Preparation and characterization of TiO2 and polymer nanocomposite films with high refractive index

Novel nanocomposite films of TiO₂ nanoparticles and hydrophobic polymers having polar groups, poly (bisphenol‐A and epichlorohydrin) or copolymer of styrene and maleic anhydride, with high refractive indices, high transparency, no color, solvent‐resistance, good thermal stability, and mechanical properties were prepared by incorporating surface‐modified TiO₂ nanoparticles into polymer matrices. In the process of preparing colloidal solution of TiO₂ nanoparticles, severe aggregation of particles can be reduced by surface modification using carboxylic acids and long‐chain alkyl amines. These TiO₂ nanoparticles dispersed in solvents were found not to aggregate after mixing with polymer solutions. Transparent colorless free‐standing films were obtained by drying a mixture of TiO₂ nanoparticles colloidal solution and polymer solutions in vacuum. Transmission electronic microscopic studies of the films suggest that the TiO₂ nanoparticles of 3–6 nm in diameter were dispersed in polymer matrices while maintaining their original size. Thermogravimetric analysis results indicate that the nanocomposite film has good thermal stability and the weight fraction of observed TiO₂ nanoparticles in the film is in good accordance with that of theoretical calculations. The refractive index of nanocomposite films of TiO₂ and poly(bisphenol‐A and epichlorohydrin) was in the range of 1.58–1.81 at 589 nm, which linearly increased with the content of TiO₂ nanoparticles from 0 to 80 wt %. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Structure and processability of iodinated poly(vinyl alcohol) (III)‐structure of films iodinated in solution before casting

Films iodinated at solution before casting (IBC films) were prepared by casting aqueous solutions of 10 wt % poly(vinyl alcohol) (PVA) containing selected quantities of I₂/KI. The quantity of I₂/KI was controlled to obtain 15.2, 39.8, 83.2, 117.0, and 140.1%. The Thermogravimetry (TG) curves of the IBC film exhibited three distinct zones corresponding to the evaporation of H₂O and I₂ molecules (zone I), evaporation of I₂ and partial decomposition of side groups (? OH) (zone II), degradation of the remaining side groups and partial degradation of the main chain (zone III‐1), and degradation of the remaining main chain and the char zone corresponding to KI. The crystalline structure of the film with a weight gain of 15.2% was almost the same as that of the pure PVA, and the film with the weight gain of 140% was almost amorphous. The differential scanning calorimetry (DSC) thermograms of the IBC films with a weight gain of 15.2% and 39.8% indicated endothermic single or double peaks at around 180°C, corresponding to the crystal melting and degradation of side groups; those with weight gains of 83.2% and above indicated exothermic peaks at around 170°C, corresponding to crystallization, and broad endothermic peak at around 180–200°C, corresponding to the crystal melting and degradation of side groups. The dynamic mechanical α_a transition of the IBC film with the weight gain of 140.1% appeared at around 20°C. X‐ray diffraction and DSC analysis of deiodinated films show that the crystal structure, on deiodination of all the IBC films, regardless of crystallinity, returned to that of the pure PVA. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 3497–3502, 2006     

Synthesis and characterization of poly(ester‐ether‐imide)s derived from 5‐(4‐trimellitimidophenoxy)‐1‐trimellitimido naphthalene

A series of novel aromatic poly(ester‐ether‐imide)s with inherent viscosity values of 0.44–0.74 dL g^?1 were prepared by the diphenylchlorophosphate‐activated direct polycondensation of an imide ring‐containing diacid namely 5‐(4‐trimellitimidophenoxy)‐1‐trimellitimido naphthalene ( 1 ) with various aromatic dihydroxy compounds in the presence of pyridine and lithium chloride. Owing to comparison of the characterization data, an ester‐containing model compound ( 2 ) was also synthesized by the reaction of 1 with phenol. The model compound 2 and the resulted polymers were fully characterized by FT‐IR and NMR spectroscopy. The ultraviolet λ_max values of the poly(ester‐ether‐imide)s were also determined. The resulting polymers exhibited an excellent organosolubility in a variety of high polar solvents such as N,N‐dimethylacetamide, N,N‐dimethylformamide, dimethyl sulfoxide, and N‐methyl‐2‐pyrrolidone. They were soluble even in common less polar organic solvents such as pyridine, m‐cresol, and tetrahydrofuran on heating. Crystallinity of the polymers was estimated by means of wide‐angle X‐ray diffraction. The resulted polymers exhibited nearly an amorphous nature. From differential scanning calorimetry thermograms, the polymers showed glass‐transition temperatures between 221 and 245°C. Thermal behaviors of the obtained polymers were characterized by thermogravimetric analysis, and the 10% weight loss temperatures of the poly(ester‐ether‐imide)s were found to be over 410°C in nitrogen. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Preparation,characterization, and antimicrobial activity of ferrocene-containing polymeric materials

Ferrocenyl(benzyl) imidazole (FcIm) and two related methyl-imidazolium salts (FcMIm⁺I^– and FcMIm⁺PF₆^–) were synthesized for their incorporation into plasticized PVC by solvent casting technique. The obtained materials were investigated for their thermal stability and, compared to pure polymer, films containing ionic ferrocene derivatives in 0.5% w/w loading were found slightly more stable. The pure ferrocene compounds showed antibacterial activity against Staphylococcus epidermis, but not against Escherichia coli, with a maximum for FcMIm⁺PF₆^– salt. After incorporation into PVC polymer, antibacterial activity against S. epidermis was observed (by disk diffusion test) only for PVC/FcMIm⁺PF₆^– (5% w/w) film, from which a release of 14.6% of the ferrocenilimidazolium cation in aqueous medium was measured after 24 hr.     

Fabrication and characterization of planar and channel polymer waveguides. II. Poly(p‐phenylene benzobisthiazole) (PBZT) films

Solutions of poly(p‐phenylene benzobisthiazole) (PBZT) in methane sulfonic acid (MSA) were prepared and studied. Solutions with concentrations less than 0.04 wt % PBZT were characterized by dilute solution viscometry. Planar PBZT waveguides were spin‐coated from a 0.5 wt % PBZT solution onto oxidized silicon wafers. The optical attentuation of the resulting polymer waveguides was measured and found to depend on both the thickness of the oxide layer on the silicon substrate and also the wavelength of the incident light. The lowest optical loss recorded for PBZT in this investigation was 4.81 ± 1.39 dB/cm at 834 nm. This work thus demonstrates the successful fabrication of PBZT into thin‐film planar waveguides. The PBZT films prepared here also show improved optical characteristics over PBZT films prepared previously by either extrusion or spin coating. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 1448–1456, 2000     

基于α-PVA/s-PVA/NaCl共混体系的薄膜制备和表征

以两种等规度不同的聚乙烯醇（PVA）为原料,水作溶剂,加入不同含量的氯化钠（NaCl）,在室温干燥、水洗、再干燥后制成无规聚乙烯醇（a-PVA）／间规聚乙烯醇（s-PvA）共混薄膜。采用差示扫描量热仪（DSC）、傅立叶红外光谱仪（FT-IR）、力学性能测试以及热失重分析（TG）等方法对薄膜进行表征。结果显示,随NaG和s-PVA的含量变化,共混膜的吸收峰和熔点规律变化,并在3％（w）NaC1时获得最佳拉伸强度和弹性模量,分别为47．54MPa与1．95GPa。共混膜的热性能随着s-PVA含量增加而提高,s-PVA所占比例从0提高到40％时,相应地薄膜的熔点从231.4℃增至239.8℃。     

Interpenetrating polymer networks of poly(dimethylsiloxane): 1. Preparation and characterization

Model networks of ,ω-dihydroxy-poly(dimethylsiloxane) (PDMS) were prepared by tetrafunctional crosslinking agent tetraethyl orthosilicate (TEOS) and the catalyst stannous 2-ethylhexanoate. Hydroxylterminated chains of PDMS having molecular weights 15 × 10³ and 75 × 10³ g mol⁻¹ were used in the crosslinking reaction. Bimodal networks were obtained from a 50% (w/w) mixture of PDMS chains with M_n = 15 × 10³ and 75 × 10³ g mol⁻¹. A sequential interpenetrating network of these PDMS chains was also prepared. Physical properties of the elastomers were determined by stress-strain tests, swelling and extraction experiments, and differential scanning calorimetry measurements.     

Preparation and characterization of poly(propylene carbonate)/exfoliated graphite nanocomposite films with improved thermal stability,mechanical properties and barrier properties

Relatively high aspect ratio exfoliated graphite (EFG) particles with an average size of 7.4 µm and a nanometer sized thickness of 30–50 nm were successfully prepared by thermal treatment at 1050 °C and subsequent ultrasonication for application as a filler to improve the physical properties of eco‐friendly poly(propylene carbonate) (PPC). A series of poly(propylene carbonate)/exfoliated graphite (PPC/EFG) nanocomposite films with different EFG contents were prepared via a solution blending method. The physical properties were strongly dependent upon the chemical and morphological structures originating from the differences in EFG composition. The morphological structures, thermal properties, mechanical properties and barrier properties of the nanocomposite films were investigated as a function of the EFG content. While all of the PPC/EFG nanocomposite films exhibited good dispersion of EFG to some extent, Fourier transform infrared and SEM results revealed that solution blending did not lead to strong interactions between PPC and EFG. As a result, poor dispersion occurred in composite films with a high EFG content. By loading EFG particles, the oxygen permeabilities, moisture permeabilities and water uptake at equilibrium decreased as the EFG content increased. Compared with pure PPC, PPC/EFG nanocomposite films have enhanced molecular ordering. Specifically, the 2% PPC/EFG composite film shows greater molecular ordering than the other composite films, which results in the highest mechanical strength. In future work, the compatibility and dispersion of the PPC matrix polymer and EFG filler particles should be increased by modifying the EFG surface or introducing additives. © 2013 Society of Chemical Industry     

Studies of chitosan. I. Preparation and characterization of chitosan/poly(vinyl alcohol) blend films

Various blending ratios of chitosan/poly (vinyl alcohol) (CS/PVA) blend films were prepared by solution blend method in this study. The thermal properties and chemical structure characterization of the CS/PVA blend films were examined by differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), dynamic mechanical analysis (DMA), and Fourier transform infrared (FTIR). Based upon the observation on the DSC thermal analysis, the melting point of PVA is decreased when the amount of CS in the blend film is increased. The FTIR absorption characteristic is changed when the amount of CS in the blend film is varied. Results of X‐ray diffraction (XRD) analysis indicate that the intensity of diffraction peak at 19° of PVA becomes lower and broader with increasing the amount of CS in the CS/PVA blend film. This trend illustrates that the existence of CS decreases the crystallinity of PVA. Although both PVA and CS are hydrophilic biodegradable polymers, the results of water contact angle measurement are still shown as high as 68° and 83° for PVA and for CS films, respectively. A minimum water contact angle (56°) was observed when the blend film contains 50 wt % CS. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Synthesis and properties of new aromatic poly(ester‐imide)s derived from 4‐p‐biphenyl‐2,6‐bis(4‐trimellitimidophenyl) pyridine and various dihydroxy compounds

A novel class of wholly aromatic poly(ester‐imide)s, having a biphenylene pendant group, with inherent viscosities of 0.32–0.49 dL g^?1 was prepared by the diphenylchlorophosphate‐activated direct polyesterification of the preformed imide‐ring‐containing diacid, 4‐p‐biphenyl‐2,6‐bis(4‐trimellitimidophenyl)pyridine (1) with various aromatic dihydroxy compounds in the presence of pyridine and lithium chloride. A reference diacid, 2,6‐bis(trimellitimido)pyridine (2) without a biphenylene pendant group and two phenylene rings in the backbone, was also synthesized for comparison purposes. At first, with due attention to structural similarity and to compare the characterization data, a model compound (3) was synthesized by the reaction of compound 1 with two mole equivalents of phenol. Moreover, the optimum condition of polymerization reactions was obtained via a study of the model compound synthesis. All of the resulting polymers were characterized by Fourier transform infrared and ¹H NMR spectroscopy and elemental analysis. The ultraviolet λ_max values of the poly(ester‐imide)s were also determined. All of the resulting polymers exhibited excellent solubility in common organic solvents, such as pyridine, chloroform, tetrahydrofuran, and m‐cresol, as well as in polar organic solvents, such as N‐methyl‐2‐pyrrolidone, N,N‐dimethylacetamide, N,N‐dimethylformamide, and dimethyl sulfoxide. The crystalline nature of the polymers obtained was evaluated by means of wide‐angle X‐ray diffraction. The resulting poly(ester‐imide)s showed nearly an amorphous nature, except poly(ester‐imide) derived from 4,4′‐dihydroxy biphenyl. The glass transition temperatures (T_g) of the polymers determined by differential scanning calorimetry thermograms were in the range 298–342 °C. The 10% weight loss temperatures (T_10%) from thermogravimetric analysis curves were found to be in the range 433–471 °C in nitrogen. Films of the polymers were also prepared by casting the solutions. Copyright © 2006 Society of Chemical Industry     

Carbon nanotube/polypropylene/polycarbonate conductive nanocomposite films: Preparation and characterization

In this study, CNT/PP/PC conductive composite films were prepared by compounding PP (polypropylene)/PC (polycarbonate) (1:1) and carbon nanotubes (CNT) using a physical blending and hot pressing method. Next, Fourier transform infrared spectroscopy, thermogravimetric analysis, differential scanning calorimetry, and water contact angle measurement are conducted in order to characterize the properties of CNT/PP/PC conductive films. The results showed there is no chemical reaction inside the PP/PC composite film with the addition of CNT. Neither the CNT composite film containing 3 wt% nor the control film decomposed thermally within 220°C. The water contact angle increased from 88.5° for the control film to 110.99° for the composite film containing 3 wt% CNT. This indicates that the film has good thermal stability and hydrophobic properties. The percolation threshold was obtained when the content of CNT was 3 wt%, and the best conductivity of the CNT/PP/PC composite film was 5.53 S/m at this time. In order to improve the tensile properties of the film, a small amount of polyurethane (TPU) was added to the film, and the maximum tensile strength was 24.91 Mpa when the content of TPU was 6.7%. This study can provide a strategy for the practical application of flexible electronic devices.     

聚乙烯醇/凹凸棒黏土纳米复合膜的制备及其性能

以聚乙烯醇(PVA)和提纯凹凸棒黏土(APT)为原料,采用溶液流延成膜法,制备了系列不同APT含量的PVA/APT纳米复合膜。采用XRD、FTIR和SEM对复合膜的结构进行了表征,测试了复合膜的热性能、力学性能和耐水性能。结果表明,APT可均匀分散在PVA基体中,APT的加入使得PVA的结晶度有所下降但并未改变其晶型。APT与PVA通过氢键作用,改善了复合膜的热稳定性、力学性能和耐水性。当APT含量为4%时,纳米复合膜有最优的性能。     

Fabrication and characterization of planar and channel polymer waveguides. III. Compositional distribution and solute loss in polymer thin films

For many microelectronic and optoelectronic applications, polymer thin films require the addition of small molecules. However, the thin‐film geometry and associated processing techniques will influence the final morphology and compositional distribution of the constituents. It is therefore important that these be examined directly rather than inferred from bulk measurements. As an example system, the concentration and distribution of Disperse Red 1 (DR1) molecules in poly(methyl methacrylate) thin films were examined. Ultraviolet visibility spectroscopy and dynamic secondary ion mass spectrometry indicate that the composition of the molecules decreased dramatically with thermal treatment of the film. The sublimation of the chromophore was observed to occur at temperatures well below the melting point of the small molecule and the glass transition of the pure polymer; this solute loss manifested itself in changes in the glass transition temperature of the film. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2021–2024, 2002     

哌嗪基单丁酰胺酸钙/锌的合成及对PVC热稳定性研究

以丁二酸酐、哌嗪、氯化钙、氯化锌为原料,通过两步反应制备了哌嗪基单丁酰胺酸钙/锌（PSACa/Zn）热稳定剂。采用元素分析、电感耦合等离子体原子发射光谱仪（ICP?OES）和傅里叶变换红外光谱仪（FTIR）对产品结构进行表征,通过刚果红试纸法、转矩流变仪法、热失重法考察了PSACa/Zn对PVC的热稳定性能,并筛选了PSACa和PSAZn的最佳配比。结果表明,PSACa和PSAZn对PVC的静态热稳定时间分别可达74.5、41.5 min,优于硬脂酸钙（CaSt₂）、硬脂酸锌（ZnSt₂）热稳定剂;PSACa和PSAZn复配使用时,以m_PSACa∶m_PSAZn=1∶1时性能最佳,对PVC静态热稳定时间可达92 min,动态热稳定时间可达905 s;发现PSACa/Zn对PVC的长期热稳定性良好。     

壳聚糖基聚电解质复合膜的制备及性能

为了克服壳聚糖薄膜力学强度差和在体液内降解太快的缺陷, 首先用"一步法"合成了—COOH含量及疏水性可控的苹果酸与乳酸共聚物(PML), 再将共聚物与壳聚糖(CS)复合, 通过溶液浇铸-挥发的方法制备改性复合薄膜。通过红外(FT-IR)、热重分析(TGA)、力学性能测试、降解实验及体外细胞毒性实验等方法对复合膜进行分析, 研究L-苹果酸(MA)与D,L-乳酸(LA)的投料比(n_MA:n_LA)对复合膜性能的影响。结果显示:当n_MA:n_LA为1:1.5时, 该共聚物与CS的复合膜拉伸强度达到54.8MPa, 断裂伸长率为10.7%, 质量损失50%所需时间为28天, 细胞相对增殖率为98.7%。研究表明:通过共聚物与壳聚糖之间的聚电解质相互作用, 有效形成了结构均匀、性能改善的薄膜, 复合膜的柔韧性提高, 降解时间适当延长, 性能可由共聚物的投料比来调节。复合膜无细胞毒性, 生物相容性好, 作为手术后防组织粘连材料具有光明的应用前景。     

Preparation and electrical conductivity of Langmuir–Blodgett films of poly(3-alkylthiophene)s

Five poly(3-alkylthiophene)s (P3ATs) with different alkyl side chains were synthesized. Pure P3ATs alone are not well suited for manipulation by the Langmuir–Blodgett (LB) technique, but their mixed systems with arachidic acid can be used to prepare high-quality Y-type films with the vertical dipping method, which was proved by UV-visible spectra and small-angle X-ray diffraction patterns. Conductivities of the LB films were measured using a two-probe method at room temperature. The conductivities exhibited obvious anisotropy and could increase by 2–4 orders of magnitude after iodine vapor doping. The influence of alkyl chain length on the conductivity in the LB films was revealed. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 1–6, 1998