Heat transfer coefficients in two phase flow for the water/lithium bromide mixture used in solar absorption refrigeration systems

This paper describes the experimental results obtained from the heat transfer in saturated nucleate boiling for the water/lithium bromide mixture flowing upward in a uniformly heated vertical tube, which is the generator of a solar absorption refrigeration system. The concentration range for the mixture was from 48 to 56 wt.% Plots of local and average heat transfer coefficients are shown against solution concentration, heat flux and the temperature difference between the wall tube and the fluid. It was observed that the average heat transfer coefficients increased for the mixture with an increase of the heat flux and with the decrease of the solution concentration and the temperature difference. The average heat transfer coefficients varied from 1.0 to 4.0 kW/m² °C.     

Experimental and Numerical Investigation on Forced Convection in Circular Tubes With Nanofluids

In this paper an experimental and numerical study to investigate the convective heat transfer characteristics of fully developed turbulent flow of a water–Al₂O₃ nanofluid in a circular tube is presented. The numerical simulations are accomplished on the experimental test section configuration. In the analysis, the fluid flow and the thermal field are assumed axial-symmetric, two-dimensional, and steady state. The single-phase model is employed to model the nanofluid mixture and the k-? model is used to describe the turbulent fluid flow. Experimental and numerical results are carried out for different volumetric flow rates and nanoparticles concentration values. Heat transfer convective coefficients as a function of flow rates and Reynolds numbers are presented. The results indicate that the heat transfer coefficients increase for all nanofluids concentrations compared to pure water at increasing volumetric flow rate. Heat transfer coefficient increases are observed at assigned volumetric flow rate for nanofluid mixture with higher concentrations, whereas Nusselt numbers present lower values than the ones for pure water.     

Experimental and numerical study of convection heat transfer of CO2 at super-critical pressures during cooling in small vertical tube

Convection heat transfer of CO₂ at super-critical pressures during cooling in a vertical small tube with inner diameter of 2.00 mm was investigated experimentally and numerically. The local heat transfer coefficients were determined through a combination of experimental measurements and numerical simulations. This study investigated the effects of pressure, cooling water mass flow rate, CO₂ mass flow rate, CO₂ inlet temperature, flow direction, properties variation and buoyancy on convection heat transfer in small tube. The results show that the local heat transfer coefficients vary significantly along the tube when the CO₂ bulk temperatures are in the near-critical region. The increase of specific heat and turbulence kinetic energy due to the density variation leads to the increase of the local heat transfer coefficients for upward flow. The buoyancy effect induced by density variation leads to a different variation trend of the local heat transfer coefficients along the tube for upward and downward flows. The numerical simulations were conducted using several k–ε turbulence models including the RNG k–ε model with a two-layer near wall treatment and three low-Reynolds number eddy viscosity turbulence models. The simulations using the low-Reynolds number k–ε model due to Yang–Shih has been found to be able to reproduce the general features exhibited in the experiments, although with a relatively large overestimation of measured wall temperatures. A better understanding of the mechanism of properties variation and buoyancy effects on convection heat transfer of CO₂ at super-critical pressures in a vertical small tube during cooling has been developed based on the information generated by the simulation on the detailed flow and turbulence fields.     

Performance characteristics of an ammonia–water absorption heat pump system

The influences of the performance parameters and the heat transfer characteristics of the absorption heat pump using ammonia–water mixture are theoretically carried out. There is a pronounced effect of the ammonia concentration ξ after rectifier on the temperature glides that has been investigated. At ξ = 0.9000 and saturation pressures of 75 and 0.5 bar, the temperature glides are 64.4°C and 81.21°C, respectively, whereas these glides are 0°C and 16.1°C at ξ = 0.9999 and at the same pressures. This mixture property considerably affects the absorption system performance and the design of the rectifier as well as other absorption components. A correlation of the Nusselt number, Nu, is developed and compared with some published work in the literature for plate type heat exchanger. The effects of ammonia concentration ξ, mass fraction spread Δξ, specific solution circulation ratio f, and pressure ratio R_p on the refrigerant mass flow rate, the pressure drop, and the heat transfer coefficients during the condensation, the evaporation, and the absorption processes are investigated. It was found that increasing ammonia mass fraction spread Δξ results in both specific circulation ratio f and R_p that have insignificant effects on the refrigerant mass flow rate. Mounting Δξ at constant f reduces the pressure drop gradually and subsequently starts to increase as Δξ escalates. The ammonia concentration ξ has insignificant effect on the evaporation heat transfer coefficient but has a little effect on the condensation and the absorber heat transfer coefficients. The ammonia mass fraction spread Δξ and f have considerable effects on the heat transfer coefficient for different absorption heat pump components. R_p has a pronounced effect on the evaporation heat transfer coefficient, although it has a slight effect on the condensation and the absorber heat transfer coefficients. The effect of R_p on the heat transfer coefficient may be eliminated in the absorber for Δξ > 0.18. Copyright © 2013 John Wiley & Sons, Ltd.     

Characteristic of local boiling heat transfer of ammonia and ammonia / water binary mixture on the plate type evaporator

Power generation using small temperature difference such as ocean thermal energy conversion (OTEC) and discharged thermal energy conversion (DTEC) is expected to be the countermeasures against global warming problem. As ammonia and ammonia/water are used in evaporators for OTEC and DTEC as working fluids, the research of their local boiling heat transfer is important for improvement of the power generation efficiency. Measurements of local boiling heat transfer coefficients were performed for ammonia /water mixture (z = 0.9−1) on a vertical flat plate heat exchanger in a range of mass flux (7.5–15 kg/m² s), heat flux (15–23 kW/m²), and pressure (0.7–0.9 MPa). The result shows that in the case of ammonia /water mixture, the local heat transfer coefficients increase with an increase of mass flux and composition of ammonia, and decrease with an increase of heat flux.     

Flow boiling heat transfer characteristics of wide-boiling mixtures

Heat transfer coefficients in horizontal flow boiling of the wide-boiling binary mixture of C₂F₆/C₂H₂F₄ and of the ternary mixture C₂F₆/SF₆/C₂H₂F₄ are measured. The experiments are carried out with the condition of uniform inner wall temperature at the tube perimeter. Results of the two boiling regions—forced convective evaporation and nucleate boiling—are obtained. In the forced convective evaporation region the results are predicted best using a pure fluid correlation which takes mixture properties into account. In the nucleate flow boiling region a degradation of the heat transfer coefficients occurs. This degradation has to be predicted with a suitable mass transfer controlled model, based on the ideal heat transfer coefficient, provided that a certain heat flux limit is not exceeded. In the region of high heat fluxes an “effective” heat transfer coefficient, based on local total vaporization, is more suitable than the previously cited ideal heat transfer coefficient.     

An Experimental Study of Flow Condensation Heat Transfer Inside Circular and Rectangular Mini-Channels

Abstract

By using unique experimental techniques and the careful construction of an experimental apparatus, the characteristics of the local heat transfer were investigated using the condensing R134a two-phase flow in horizontal single mini-channels. The circular channels (D _h = 0.493, 0.691, and 1.067 mm) and rectangular channels (Aspect Ratio = 1.0; D _h = 0.494, 0.658, and 0.972 mm) were tested and compared. Tests were performed for a mass flux of 100, 200, 400, and 600 kg/m²s, a heat flux of 5 to 20 kW/m², and a saturation temperature of 40°C. In this study, the effect of heat flux, mass flux, vapor qualities, hydraulic diameter, and channel geometry on flow condensation were investigated, and the experimental local condensation heat transfer coefficients are shown. The experimental data of condensation Nusselt number are compared with existing correlations.     

Heat transfer on a horizontal rotating cylinder near a flat plate in a cross‐flow

An experimental study of heat transfer on a horizontal rotating cylinder near a flat plate was performed. The cylinder and plate were set in a cross‐flow. Temperature distribution and coefficients of local heat transfer were measured by a Mach–Zehnder interferometer. Flow visualization was made using smoke. Rotating Reynolds numbers (Re_r) and cross‐flow Reynolds numbers (Re_d) were varied from 0 to 2000. The spaces between cylinder and plate were varied from 1 × 10^?3 m to 5 × 10^?3 m. The rotating direction of cylinder was changed clockwise or counterclockwise. The following results are obtained: When the space between the rotating cylinder and flat plate is the same as the displacement thickness on the plate, the heat transfer on the cylinder near the plate has the best performance. We have procured the empirical equation of heat transfer from a rotating cylinder near the flat plate in the cross‐flow. 8 2010 Wiley Periodicals, Inc. Heat Trans Asian Res; Published online in Wiley Online Library ( wileyonlinelibrary.com ). DOI 10.1002/htj.20329     

Enhancement of nucleate pool boiling heat transfer in ammonia/water mixtures (Effect of surface‐active agent)

Nucleate boiling heat transfer coefficients of ammonia/water mixtures have been measured when a surface‐active agent was added into the mixtures. The experiment has been carried out on a horizontal heated wire at a pressure of 0.4 MPa. The effect of concentration of the ammonia and the surface‐active agent on the coefficients was investigated experimentally for the ammonia fractions C = 0.3 and 0.7 and the surfactant concentration C_S = 0 to 3500 ppm. The result shows that just after onset of boiling the nucleate boiling heat transfer coefficient enhances at the lower ammonia fraction i.e., C = 0.3. It was found that the enhancement effect by the surface‐active agent disappeared when the surfactant concentration is more than 1000 ppm at an ammonia fraction C = 0.3. It is also shown that the generated heat of mixing near the vaporBliquid interface can be removed easily and the pressure and temperature in the system can be controlled easily by placing a cooling pipe on the vaporBliquid interface, resulting in improvement of accuracy in measuring the heat transfer coefficients. We correlated the effect of the surfactant on the heat transfer coefficient using the improved measurement data in the current paper. 8 2010 Wiley Periodicals, Inc. Heat Trans Asian Res; Published online in Wiley Online Library ( wileyonlinelibrary.com ). DOI 10.1002/htj.20328     

Forced convective boiling of nonazeotropic refrigerant mixtures inside enhanced surface tubing

An experimental study on the characteristics of two phase flow boiling of pure refrigerants such as R12 and R22 as well as nonazeotropic refrigerant mixtures R22/R114 and R22/R152a inside horizontal enhanced surface tubing is presented. The enhanced surface tubing results showed a significant improvement of the heat transfer over that of an equivalent smooth tube, depending on the mixture components and their concentrations. Correlations are proposed to predict the heat transfer characteristics such as average heat transfer coefficients as well as pressure drops of nonazeotropic refrigerant mixture flow boiling inside enhanced surface tubing. In addition, it was found that the refrigerant mixtures pressure drop is a weak function of the mixture compositions.     

Numerical and Experimental Investigation of Heat Transfer of α-Al2O3/Water Nanofluid in Double Pipe and Shell and Tube Heat Exchangers

This research presents an experimental and numerical study on the heat transfer of α-Al₂O₃/water nanofluid flowing through the double pipe and shell and tube heat exchangers, under laminar flow conditions. Effects of important parameters such as hot and cold volume flow rates, nanofluid temperature, and nanoparticles concentration on the heat transfer characteristics are investigated. The results indicated that the heat transfer performance of both double pipe and shell and tube heat exchangers increases with increasing the hot and cold volume flow rates, as well as the particle concentrations and nanofluid inlet temperature. Compared with pure water, the results indicated that the heat transfer coefficients of nanofluid in the double pipe and shell and tube heat exchangers are higher than those of water by 13.2% and 21.3%, respectively. Also, the heat transfer performance of nanofluid in a shell and tube heat exchanger is 26.2% higher than the double pipe heat exchanger. A computational fluid dynamics (CFD) technique was used for heat transfer simulation in the previously mentioned heat exchangers. Computed overall heat transfer coefficients of the nanofluids are in good agreement with the experimental data.     

Analysis of microchannel heat sink performance using nanofluids

In this study, silicon microchannel heat sink performance using nanofluids as coolants was analyzed. The nanofluid was a mixture of pure water and nanoscale Cu particles with various volume fractions. The heat transfer and friction coefficients required in the analysis were based on theoretical models and experimental correlations. In the theoretical model, nanofluid was treated as a single-phase fluid. In the experimental correlation, thermal dispersion due to particle random motion was included. The microchannel heat sink performances for two specific geometries, one with W_ch = W_fin = 100 μm and L_ch = 300 μm, the other with W_ch = W_fin = 57 μm and L_ch = 365 μm, were examined. Because of the increased thermal conductivity and thermal dispersion effects, it was found that the performances were greatly improved for these two specific geometries when nanofluids were used as the coolants. In addition to heat transfer enhancement, the existence of nanoparticles in the fluid did not produce extra pressure drop because of small particle size and low particle volume fraction.     

Experimental evaluation of a single-stage heat transformer operating with the water/Carrol™ mixture

This paper describes experimental results obtained with a single-stage heat transformer (SSHT). Many combinations of fluid pairs have been proposed although only the water/lithium bromide mixture has been widely used. The experimental work was done using the water/Carrol™ mixture, where Carrol™ is a mixture of LiBr and ethylene glycol [(CH₂OH)₂] in the ratio 1:4.5 by weight. Flow ratios, gross temperature lifts, useful heat, and coefficients of performance are plotted for the heat transformer vs temperatures and solution concentrations. Because the water/Carrol™ mixture has higher solubility than water/lithium bromide and high experimental values are obtained for the gross temperature lift, it is a preferred mixture.     

A new method for determining coupled heat and mass transfer coefficients between air and liquid desiccant

This paper presented the characteristic of liquid desiccant dehumidification based on NTU–Le model. The results showed that the Lewis number Le had little effect on air outlet humidity ratio during desiccant solution dehumidification process. A new method called h_D–Le separative evaluation method was developed for determining coupled heat and mass transfer coefficients between air and liquid desiccant, through which the heat and mass transfer coefficients between air and liquid desiccant were calculated to obtain from experimental inlet and outlet parameters of air and desiccant solution. The effects of the air volume flow rate, temperature, humidity ratio and the solution concentration, temperature on the Lewis number, heat and mass transfer coefficient were analyzed according to experimental data and the h_D–Le separative evaluation method. Based on the computation results, it was concluded that the Lewis number greatly depended on the operation parameters and conditions of the air and desiccant. In addition, the correlations of the heat and mass transfer coefficients were developed. The additional 74 groups of experiments validated the developed correlations by comparison of air/solution parameters change with the calculation data.     

Experimental study on saturated flow boiling heat transfer of R290/R152a binary mixtures in a horizontal tube

An experimental study on the saturated flow boiling heat transfer for a binary mixture of R290/R152a at various compositions is conducted at pressures ranging from 0.2 to 0.4 MPa. The heat transfer coefficients are experimentally measured over mass fluxes ranging from 74.1 to 146.5 kg/(m²·s) and heat fluxes ranging from 13.1 to 65.5 kW/m². The influences of different parameters such as quality, saturation pressure, heat flux, and mass flux on the local heat transfer coefficient are discussed. Existing correlations are analyzed. The Gungor-Winterton correlation shows the best fit among experimental data for the two pure refrigerants. A modified correlation for the binary mixture is proposed based on the authors’ previous work on pool boiling heat transfer and the database obtained from this study. The result shows that the total mean deviation is 10.41% for R290/R152a mixtures, with 97.6% of the predictions falling within ±30%.     

Flow boiling heat transfer coefficient of R-134a/R-290/R-600a mixture in smooth horizontal tubes using varied heat flux method

An experimental study on in-tube flow boiling heat transfer of R-134a/R-290/R-600a refrigerant mixture has been carried out under varied heat flux test conditions. The heat transfer coefficients are experimentally measured at temperatures between ?8 and 5 °C for mass flow rates of 3–5 g s^?1. Acetone is used as a hot fluid which flows in the outer tube of diameter 28.57 mm while the refrigerant mixture flows in the inner tube of diameters 9.52 and 12.7 mm. By regulating the acetone flow conditions, the heat flux is maintained between 2 and 8 kW/m² and the pressure of the refrigerant is maintained between 3.2 and 5 bar. The comparison of experimental results with the familiar correlations shows that the correlations over predict the heat transfer coefficients for this mixture when stratified and stratified-wavy flow prevail. Multiple regression technique is used to evolve and modify existing correlations to predict the heat transfer coefficient of the refrigerant mixture. It is found that the modified version of Lavin–Young correlation (1965) predicts the heat transfer coefficient of the considered mixture within an average deviation of ±20.5 %.     

Flow boiling of liquid nitrogen in micro-tubes: Part II – Heat transfer characteristics and critical heat flux

This paper is the second portion of a two-part study concerning the flow boiling of liquid nitrogen in the micro-tubes with the diameters of 0.531, 0.834, 1.042 and 1.931 mm. The contents include the heat transfer characteristics and critical heat flux (CHF). The local wall temperatures are measured, from which the local heat transfer coefficients are determined. The influences of heat flux, mass flux, pressure and tube diameter on the flow boiling heat transfer coefficients are investigated systematically. Two regions with different heat transfer mechanism can be classified: the nucleate boiling dominated region for low mass quality and the convection evaporation dominated region for high mass quality. For none of the existed correlations can predict the experimental data, a new correlation expressed by Co, Bo, We, K_p and X is proposed. The new correlation yields good fitting for 455 experimental data of 0.531, 0.834 and 1.042 mm micro-tubes with a mean absolute error (MAE) of 13.7%. For 1.931 mm tube, the flow boiling heat transfer characteristics are similar to those of macro-channels, and the heat transfer coefficient can be estimated by Chen correlation. Critical heat flux (CHF) is also measured for the four tubes. Both the CHF and the critical mass quality (CMQ) are higher than those for conventional channels. According to the relationship that CMQ decreases with the mass flux, the mechanism of CHF in micro-tubes is postulated to be the dryout or tear of the thin liquid film near the inner wall. It is found that CHF increases gradually with the decrease of tube diameter.     

Fluid flow and heat transfer of natural convection over upward‐facing,horizontal, heated plate shrouded by a parallel insulated plate

The present paper describes experimental results on the fluid flow and heat transfer of natural convection between a horizontal, heated plate facing upward and an insulated cover plate. The experiments were carried out with water. The width of the test plates W and their gaps H were changed from W = 50 to 250 mm and H = 10 to 30 mm and ∞ (no cover plate). The visualization studies with dye and liquid crystal thermometry revealed that the roll cells whose axes are perpendicular to the flow direction appear and become dominant over the heated plate on decreasing the gap. These roll cells inhibit the heat transfer, and thus, the heat transfer coefficients become smaller than those without a cover plate. It was found that the flow and heat transfer in the region near the plate edges are unaffected by the cover plate. The conditions of the above reduced heat transfer were determined empirically. Moreover, nondimensional correlations for the local and the overall heat transfer coefficients of the heated plates are proposed based on the present heat transfer results. © 2000 Scripta Technica, Heat Trans Asian Res, 29(4): 333–346, 2000     

Suspension-to-wall heat transfer in a 12-MWth circulating fluidized-bed combustor

An experimental investigation was carried out to study the effects of operating parameters on the local suspension-to-wall heat transfer in the combustor of a 12-MW_th circulating fluidized-bed (CFB) boiler. The heat transfer coefficients were measured with a conduction-type heat flux meter at five different vertical levels. The measurements covered a range of superficial gas velocities from 4 to 6 m/s, a bulk bed temperature from 800 to 850 °C and a suspension density from 6 to 70 kg/m³ for 270-μm silica sand particles. The heat transfer coefficient for the membrane wall in the combustion chamber of the CFB boiler was in the range of 100 to 180 W/m² K for the range of operating conditions employed in this work. The heat transfer coefficient decreased with increasing height and increased with increasing bulk bed temperature, superficial gas velocity and suspension density. Based on the experimental data, a simple correlation is proposed for predicting the suspension-to-membrane wall heat transfer coefficient. The results were analysed and compared with the experimental data of other workers.     

Flow and heat transfer behaviors of phase change material slurries in a horizontal circular tube

The flow and convective heat transfer behaviors of microencapsulated phase change material (MPCM) slurries in a horizontal circular tube have been experimentally investigated. The slurry consisted of microencapsulated 1-bromohexadecane (C₁₆H₃₃Br) and water, with the mass fractions of MPCM varying from 5% to 27.6%. The pressure drop and local heat transfer coefficients were measured, and the influences of capsule fractions, heating rates, and flow structures on heat transfer performance were also studied. Heat transfer coefficients measured for MPCM slurry are significantly higher than for those for single-phase fluid flow in laminar flow conditions, but exhibit more complicated phenomena at low turbulent conditions. Moreover, a new simple heat transfer correlation equation was proposed that accurately predicts the local heat transfer coefficients of laminar MPCM slurry flow in a horizontal circular tube.