Role of ZnO in Cu/ZnO/Al2O3 catalyst for hydrogenolysis of butyl butyrate

For hydrogenolysis of butyl butyrate (BB), a series of Cu/ZnO/Al₂O₃ catalysts with different metal compositions were prepared, and characterized by N₂O chemisorption for measuring Cu surface area and by chromatographic experiment for determining the heat of BB adsorption. As a result, the presence of ZnO in Cu-based catalysts was found to enhance the catalytic activity of Cu due to dual function of ZnO. The Cu surface area was linearly correlated with the butanol productivity, demonstrating that ZnO exerts the structural function in Cu/ZnO/Al₂O₃ catalysts. Additionally, the role of ZnO as a chemical contributor was revealed such that its presence leads to lower activation energy of the surface reaction, thus resulting in higher Cu catalytic activity obtained at a low temperature such as 200 °C. Consequently, optimizing the Cu/Zn ratio in Cu/ZnO/Al₂O₃ catalyst is required to tune its structural and chemical characteristics of Cu metals, and thus to obtain a higher activity on the hydrogenolysis reaction.     

Improvement of coke resistance of Ni/Al2O3 catalyst in CH4/CO2 reforming by ZrO2 addition

This work investigates the improvement of Ni/Al₂O₃ catalyst stability by ZrO₂ addition for H₂ gas production from CH₄/CO₂ reforming reactions. The initial effect of Ni addition was followed by the effect of increasing operating temperature to 500–700 °C as well as the effect of ZrO₂ loading and the promoted catalyst preparation methods by using a feed gas mixture at a CH₄:CO₂ ratio of 1:1.25. The experimental results showed that a high reaction temperature of 700 °C was favored by an endothermic dry reforming reaction. In this reaction the deactivation of Ni/Al₂O₃ was mainly due to coke deposition. This deactivation was evidently inhibited by ZrO₂, as it enhances dissociation of CO₂ forming oxygen intermediates near the contact between ZrO₂ and nickel where the deposited coke is gasified afterwards. The texture of the catalyst or BET surface area was affected by the catalyst preparation method. The change of the catalyst texture resulted from the formation of ZrO₂–Al₂O₃ composite and the plugging of Al₂O₃ pore by ZrO₂. The 15% Ni/10% ZrO₂/Al₂O₃ co-impregnated catalyst showed a higher BET surface area and catalytic activity than the sequentially impregnated catalyst whereas coke inhibition capability of the promoted catalysts prepared by either method was comparable. Further study on long-term catalyst stability should be made.     

Gas phase hydrogenation of maleic anhydride to tetrahydrofuran by Cu/ZnO/TiO2 catalysts in the presence of n-butanol

Cu/ZnO/TiO₂ catalysts were prepared via the coprecipitation method. The catalysts were characterized by X-ray diffraction, X-ray photoelectron spectrometry, temperature programmed reduction, and N₂ adsorption. The catalytic activity of Cu/ZnO/TiO₂ catalyst in gas phase hydrogenation of maleic anhydride in the presence of n-butanol was studied at 235–280 °C and 1 MPa. The conversion of maleic anhydride was more than 95.7% and the selectivity of tetrahydrofuran was up to 92.7%. At the same time, n-butanol was converted to butyraldehyde and butyl butyrate via reactions, namely, dehydrogenation, disproportionation, and esterification. There were two kinds of CuO species present in the calcined Cu/ZnO/TiO₂ catalysts. At a lower copper content, the CuO species strongly interacted with ZnO and TiO₂; at a higher copper content, both the surface-anchored and bulk CuO species were present. The metallic copper (CuO) produced by the reduction of the surface-anchored CuO species favored the deep hydrogenation of maleic anhydride to tetrahydrofuran. The deep hydrogenation activity of Cu/ZnO/TiO₂ catalyst increased with the decrease of crystallite sizes of CuO and the increase of microstrain values. Compensations of reaction heat and H₂ in the coupling reaction of maleic anhydride hydrogenation and n-butanol dehydrogenation were distinct.     

Catalytic behaviour of Cu/ZrO2 and Cu/ZrO2(SO 4 2− ) in the reduction of nitric oxide by decane in oxygen-rich atmosphere

The selective catalytic reduction (SCR) of NO by decane under an oxidising atmosphere has been carried out on Cu/ZrO₂ and Cu/ZrO₂(SO ₄ ^2– ). Zirconia-supported Cu catalysts were prepared by ligand exchange with Cu acetylacetonate followed by calcination at 773 K. The solids obtained were characterised by temperature programmed reduction (TPR) by hydrogen and temperature programmed desorption (TPD) of NO. Cu/ZrO₂ is active and selective in the reduction of NO by decane at low temperature (< 600 K) but oxidises NO to NO₂ between 640 and 770 K. By contrast, whatever the temperature, a total selectivity to nitrogen is obtained with Cu/ZrO₂(SO ₄ ^2– ). About 40% NO conversion to N₂ is observed with GHSV of 70 000 h^–1. The promoting effect of sulfate is attributed to the large increase of acidity and the strong interaction between copper and sulfur species which is evidenced by TPD of NO and TPR by H₂.     

Trimerization of isobutene over WOx/ZrO2 catalysts

Trimerization of isobutene to produce isobutene trimers has been investigated over WO_x/ZrO₂ catalysts that were obtained by wet-impregnation and successive calcination at high temperatures. Very stable isobutene conversion and high selectivity for trimers are attained over a WO_x/ZrO₂ catalyst obtained by calcination at 700 °C. From the XRD study it can be understood that tetragonal ZrO₂ is beneficial for stable performance; however, monoclinic ZrO₂ is not good for trimerization. Nitrogen adsorption and FTIR experiments suggest that amorphous WO_x/ZrO₂ is inefficient catalyst even though it has high surface area and high concentration of acid sites. The observed performance with the increased selectivity and stable conversion demonstrates that a WO_x/ZrO₂ having tetragonal zirconia, even with decreased porosity and acid sites, is one of the best catalysts to exhibit stable and high conversion, high selectivity for trimers and facile regeneration.     

Reduction of NO by CO on Cu/ZrO2/Al2O3 catalysts: Characterization and catalytic activities

ZrO₂, γ-Al₂O₃ and ZrO₂/γ-Al₂O₃-supported copper catalysts have been prepared, each with three different copper loads (1, 2 and 5 wt%), by the impregnation method. The catalysts were characterized by nitrogen adsorption (BET), X-ray diffraction (XRD), temperature programmed reduction (TPR) with H₂, Raman spectroscopy and electronic paramagnetic resonance (EPR). The reduction of NO by CO was studied in a fixed-bed reactor packed with these catalysts and fed with a mixture of 1% CO and 1% NO in helium. The catalyst with 5 wt% copper supported on the ZrO₂/γ-Al₂O₃ matrix achieved 80% reduction of NO. Approximately the same rate of conversion was obtained on the catalyst with 2 wt% copper on ZrO₂. Characterization of these catalysts indicated that the active copper species for the reduction of NO are those in direct contact with the oxygen vacancies found in ZrO₂.     

NOx storage behavior and sulfur-resisting performance of the third-generation NSR catalysts Pt/K/TiO2–ZrO2

The NO_x storage and reduction (NSR) catalysts Pt/K/TiO₂–ZrO₂ were prepared by an impregnation method. The techniques of XRD, NH₃-TPD, CO₂-TPD, H₂-TPR and in situDRIFTS were employed to investigate their NO_x storage behavior and sulfur-resisting performance. It is revealed that the storage capacity and sulfur-resisting ability of these catalysts depend strongly on the calcination temperature of the support. The catalyst with theist support calcined at 500 °C, exhibits the largest specific surface area but the lowest storage capacity. With increasing calcination temperature, the NO_x storage capacity of the catalyst improves greatly, but the sulfur-resisting ability of the catalyst decreases. In situ DRIFTS results show that free nitrate species and bulk sulfates are the main storage and sulfation species, respectively, for all the catalysts studied. The CO₂-TPD results indicate that the decomposition performance of K₂CO₃ is largely determined by the surface property of the TiO₂–ZrO₂ support. The interaction between the surface hydroxyl of the support and K₂CO₃ promotes the decomposition of K₂CO₃ to form –OK groups bound to the support, leading to low NO_x storage capacity but high sulfur-resisting ability, while the interaction between the highly dispersed K₂CO₃ species and Lewis acid sites gives rise to high NO_x storage capacity but decreased sulfur-resisting ability. The optimal calcination temperature of TiO₂–ZrO₂ support is 650 °C.     

Dehydrogenation of cyclohexanol on Cu–ZnO/SiO2 catalysts: The role of copper species

For the dehydrogenation of cyclohexanol a series of Cu–ZnO/SiO₂ catalysts with various Cu to ZnO molar ratios was prepared using the impregnation method, with the loading of copper fixed at 9.5 at.%. The catalysts were characterized by XPS, H₂–N₂O titration, BET, H₂-TPR, NH₃-TPD and XRD techniques. The results indicate that the addition of ZnO can improve the dispersion of copper species on reduced Cu–ZnO/SiO₂ (CZS) catalysts. Cu⁰ and Cu⁺ species were found on the reduced CZS catalysts surface, and the amount of Cu⁺ increased with the content of ZnO increasing. The addition of ZnO increased the acidity of the CZS catalysts. However, only Cu⁰ species can be found on the reduced Cu/SiO₂ (CS) catalyst surface. According to the reaction results, we found that the selectivity to phenol was related to the amount of Cu⁺ species, the Cu⁺ species should be the active sites for the production of phenol, the Cu⁰ is responsible for cyclohexanol dehydrogenation to cyclohexanone.     

Carbon dioxide reforming of ethanol over Ni/Y2O3–ZrO2 catalysts

Supported nickel catalysts of composition Ni/Y₂O₃–ZrO₂ were synthesized in one step by the polymerization method and compared with a nickel catalyst prepared by wet impregnation. Stronger interactions were observed in the formed catalysts between NiO species and the oxygen vacancies of the Y₂O₃–ZrO₂ in the catalysts made by polymerization, and these were attributed to less agglomeration of the NiO during the synthesis of the catalysts in one step. The dry reforming of ethanol was catalyzed with a maximum CO₂ conversion of 61% on the 5NiYZ catalyst at 800 °C, representing a better response than for the catalyst of the same composition prepared by wet impregnation.     

Investigating the effect of metal oxide additives on the properties of Cu/ZnO/Al2O3 catalysts in methanol synthesis from syngas using factorial experimental design

The Cu/ZnO/Al₂O₃ catalysts, prepared by co-precipitation method, have been modified by adding small amount of Mn, Mg, Zr, Cr, Ba, W and Ce oxides using design of experiments (1/16 full factorial design). The structure and morphology of catalysts were studied by X-ray diffraction (XRD) and BET. Performance of the prepared catalysts for CO/CO₂ hydrogenation to methanol was evaluated by using a stainless steel fixed-bed reactor at 5 MPa and 513 K. The oxide additives were found to influence the catalytic activity, dispersion of Cu, Cu crystallite size, surface composition of catalyst and stability of catalysts during their operations. The results showed that the Mn and Zr promoted catalysts have high performance for methanol synthesis from syngas.     

Effect of ceria on the structure and catalytic activity of V2O5/TiO2–ZrO2 for oxidehydrogenation of ethylbenzene to styrene utilizing CO2 as soft oxidant

The present study was undertaken to investigate the influence of ceria on the physicochemical and catalytic properties of V₂O₅/TiO₂–ZrO₂ for oxidative dehydrogenation of ethylbenzene to styrene utilizing CO₂ as a soft oxidant. Monolayer equivalents of ceria, vanadia and ceria–vanadia combination over TiO₂–ZrO₂ (TZ) support were impregnated by a coprecipitation and wet impregnation methods. Synthesized catalysts were characterized by using X-ray diffraction, Raman spectroscopy, X-ray photoelectron spectroscopy, temperature programmed reduction, transmission electron microscopy and BET surface area methods. The XRD profiles of 550 °C calcined samples revealed amorphous nature of the materials. Upon increasing calcination temperature to 750 °C, in addition to ZrTiO₄ peaks, few other lines due to ZrV₂O₇ and CeVO₄ were observed. The XPS V 2p results revealed the existence of V⁴⁺ and V⁵⁺ species at 550 and 750 °C calcinations temperatures, respectively. TEM analysis suggested the presence of nanosized (<7 nm) particles with narrow range distribution. Raman measurements confirmed the formation ZrTiO₄ under high temperature treatments. TPR measurements suggested a facile reduction of CeO₂–V₂O₅/TZ sample. Among various samples evaluated, the CeO₂–V₂O₅/TZ sample exhibited highest conversion and nearly 100% product selectivity. In particular, the addition of ceria to V₂O₅/TZ suppressed the coke deposition and allowed a stable and high catalytic activity.     

Effects of Pretreatments of Cu/ZnO-Based Catalysts on Their Activities for the Water–Gas Shift Reaction

The effects of the pretreatments of Cu/ZnO-based catalysts prepared by a coprecipitation method on their activities for the water–gas shift reaction at 523K were investigated. The activity of a Cu/ZnO/ZrO₂/Al₂O₃ catalyst for the water–gas shift reaction was less affected by calcination at temperatures ranging from 673-973K and by H₂ treatment at 573 or 723K than that of a Cu/ZnO/Al₂O₃ catalyst. The catalyst activity could be correlated mainly to the Cu surface area of the catalyst.     

Synthesis and characterization of CuO/TiO2 catalysts for low-temperature CO oxidation

In this paper, the CuO/TiO₂ catalysts prepared by the deposition–precipitation (DP) method were extensively investigated for CO oxidation reaction. The structural characters of the CuO/TiO₂ catalysts were comparatively investigated by TG-DTA, XRD, and XPS measurements. It was shown that the catalytic behavior of CuO/TiO₂ catalysts greatly depended on the TiO₂-support calcination temperature, the CuO loading amount and the CuO/TiO₂ catalysts calcination temperature. CuO supported on the anatase phase of TiO₂-support calcined at 400 °C showed better catalytic activity than those supported on TiO₂ calcined at 500 and 700 °C. Among all our investigated catalysts with CuO loading from 2% to 12%, the catalyst with 8 wt% CuO loading exhibited the highest catalytic activity. The optimum calcination temperature of the CuO/TiO₂ catalysts was 300 °C. The XRD results indicated that the catalytic activity of the CuO/TiO₂ catalysts was related to the crystal phase and particle size of TiO₂ support and CuO active component.     

Effects of Co dopants and flame conditions on the formation of Co/ZrO2 nanoparticles by flame spray pyrolysis and their catalytic properties in CO hydrogenation

The Co/ZrO₂ catalysts with various Co loadings (5–10 wt.%) were prepared by one-step flame spray pyrolysis (FSP) under different flame conditions. As revealed by XRD and TEM, all the resulting Co/ZrO₂ nanoparticles were composed of single-crystalline particles exhibiting the characteristic tetragonal structure of ZrO₂. Varying the amount of Co dopants during FSP synthesis did not alter the primary particle size of ZrO₂ which was determined to be ca. 14 nm. On the other hand, increasing precursor feed rate from 3 to 8 ml/min resulted in an increase of ZrO₂ crystallite size from 10 to 19 nm. The higher precursor feed rate produced higher enthalpy of flame and longer residence times, which increased coalescence and sintering of the particles. Compared to the Co/ZrO₂ prepared by conventional impregnation method, the catalytic activities of the FSP-made catalysts were much higher. Moreover, the hydrogenation rates of the FSP-made Co/ZrO₂ catalysts were increased with increasing Co loading and precursor feed rate. According to H₂ chemisorption and H₂ temperature program reduction results, the improvement of catalytic activity and C₂–C₆ selectivities of the FSP-made catalysts in the CO hydrogenation was attributed to the higher number of Co metal active sites and lower interaction between Co/CoO and ZrO₂ support obtained via the FSP synthesis.     

Onset coarsening-coalescence kinetics of ZrO2 and less refractory TiO2 nanoparticles: Effect of homologous temperature and phase transformation

Specific surface area change of ZrO₂ (predominant tetragonal - (t) symmetry, 30-50 nm) and less refractory TiO₂ anatase nanoparticles (20-50 nm) upon isothermal firing at 700-1000 °C in air was determined by N₂ adsorption-desorption hysteresis isotherm. The nanoparticles underwent onset coarsening-coalescence within minutes without appreciable phase transformation for TiO₂, but with extensive transformation into monoclinic (m-) symmetry for ZrO₂. The apparent activation energy of such a process being not much higher for ZrO₂ (77 ± 23 kJ/mol) than TiO₂ (56 ± 3 kJ/mol) nanoparticles can be attributed to transformation plasticity. The minimum temperature for coarsening/coalescence of the present ZrO₂ and TiO₂ nanoparticles was estimated as 710 and 641 °C, respectively.     

Synthesis of a TiO2 ceramic membrane containing SrCo0.8Fe0.2O3 by the sol-gel method with a wet impregnation process for O2 and N2 permeation

A SrCo_0.8Fe_0.2O₃ impregnated TiO₂ membrane (TiO₂-SrCo_0.8Fe_0.2O₃ membrane) was successfully prepared using a sol-gel method in combination with a wet impregnation process. The membrane was subjected to a single gas permeance test using oxygen (O₂) and nitrogen (N₂). The TiO₂ membrane was immersed in the SrCo_0.8Fe_0.2O₃ solution, dried and then calcined to affix SrCo_0.8Fe_0.2O₃ into the membrane. The effect of the acid/alkoxide (H⁺/Ti⁴⁺) molar ratio of the TiO₂ sol on the TiO₂ phase transformation was investigated. The optimal molar ratio was found to be 0.5, which resulted in nanoparticles with a mean size of 5.30 nm after calcination at 400 °C. The effect of calcination temperature on the phase transformation of TiO₂ and SrCo_0.8Fe_0.2O₃ was investigated by varying the calcination temperature from 300 to 500 °C. X-ray diffraction spectroscopy (XRD) and Fourier transform infrared (FTIR) analysis confirmed that a calcination temperature of 400 °C was preferable for preparing a TiO₂-SrCo_0.8Fe_0.2O₃ membrane with fully crystallized anatase and SrCo_0.8Fe_0.2O₃ phases. The results also showed that polyvinyl alcohol (PVA) and hydroxypropyl cellulose (HPC) were completely removed. Field emission scanning electron microscopy (FESEM) analysis results showed that a crack-free and relatively dense TiO₂ membrane (∼0.75 μm thickness) was created with a multiple dip-coating process and calcination at 400 °C. The gas permeation results show that the TiO₂ and TiO₂-SrCo_0.8Fe_0.2O₃ membranes exhibited high permeances. The TiO₂-SrCo_0.8Fe_0.2O₃ membrane developed provided greater O₂/N₂ selectivity compared to the TiO₂ membrane alone.     

The catalytic performance in oxidative coupling of methane and the surface basicity of La2O3, Nd2O3, ZrO2 and Nb2O5

The catalytic performance in oxidative coupling of methane (OCM) of unmodified pure La₂O₃, Nd₂O₃, ZrO₂ and Nb₂O₅ has been investigated under various conditions. The results confirmed that the activity of La₂O₃ and Nd₂O₃ was always much higher than that of the remaining two. The surface basicity/base strength distribution of pure La₂O₃, Nd₂O₃, ZrO₂ and Nb₂O₅ was measured using a test reaction of transformation of 2-butanol and a temperature-programmed desorption of CO₂. Both methods showed that La₂O₃ and Nd₂O₃ had high basicity and contained medium and strong basic sites (lanthanum oxide more and neodymium oxide somewhat less). ZrO₂ had only negligible amount of weak basic sites and Nb₂O₅ was rather acidic. The confrontation of the basicity and catalytic performance indicated that in the case of investigated oxides, the basicity (especially strong basic sites) could be a decisive factor in determination of the catalytic activity in OCM. Only in the case of ZrO₂ it was observed a moderate catalytic performance in spite of negligible basicity. The influence of a gas atmosphere used in the calcination of oxides (flowing oxygen, helium and nitrogen) on their basicity and catalytic activity in OCM had been also investigated. Contrary to earlier observations with MgO, no effect of calcination atmosphere on the catalytic performance of investigated oxides in OCM and on their basicity was observed.     

Study of ruthenium supported on Ta2O5–ZrO2 and Nb2O5–ZrO2 as catalysts for the partial oxidation of methane

Ru-based catalysts supported on Ta₂O₅–ZrO₂ and Nb₂O₅–ZrO₂ are studied in the partial oxidation of methane at 673–873 K. Supports with different Ta₂O₅ or Nb₂O₅ content were prepared by a sol–gel method, and RuCl₃ and RuNO(NO₃)₃ were used as precursors to prepare the catalysts (ca. 2 wt.% Ru). At 673 K high selectivity to CO₂ was found. An increase of temperature up to 773 K produced an increase in the selectivity to syngas (H₂/CO = 2.2–3.1), and this is related with the transformation of RuO₂ to metallic Ru as was determined from XRD and XPS results. At 873 K and with co-fed CO₂ an increase of the catalytic activity and CO selectivity was found. A TOF value of 5.7 s⁻¹ and H₂/CO ratio ca. 1 was achieved over Ru(Cl)/6TaZr. Catalytic results are discussed as a function of the support composition and characteristics of Ru-based phases.     

Hydrogen production by steam reforming of LNG over Ni/Al2O3-ZrO2 catalysts: Effect of ZrO2 and preparation method of Al2O3-ZrO2

An Al₂O₃-ZrO₂ support was prepared by grafting a zirconium precursor onto the surface of commercial γ-Al₂O₃. A physical mixture of Al₂O₃-ZrO₂ was also prepared for the purpose of comparison. Ni/Al₂O₃-ZrO₂ catalysts were then prepared by an impregnation method, and were applied to the hydrogen production by steam reforming of liquefied natural gas (LNG). The effect ZrO₂ and preparation method of Al₂O₃-ZrO₂ on the performance of supported nickel catalysts in the steam reforming of LNG was investigated. The Al₂O₃-ZrO₂ prepared by a grafting method was more efficient as a support for nickel catalyst than the physical mixture of Al₂O₃-ZrO₂ in the hydrogen production by steam reforming of LNG. The well-developed tetragonal phase of ZrO₂ and the high dispersion of ZrO₂ on the surface of γ-Al₂O₃ were responsible for the enhanced catalytic performance of Ni/Al₂O₃-ZrO₂ prepared by way of a grafting method.     

Influence of composition of MgAl2O4 supported NiCeO2ZrO2 catalysts on coke formation and catalyst stability for dry reforming of methane

Dry reforming of methane was studied over Ni catalysts supported on γAl₂O₃, CeO₂, ZrO₂ and MgAl₂O₄ (670 °C, 1.5 bar, 16–20 l CH₄ ml_catalyst⁻¹ h⁻¹). It is shown that MgAl₂O₄ supported Ni catalysts promoted with both CeO₂ and ZrO₂ are promising catalysts for dry reforming of methane with carbon dioxide. Within a certain composition range, the simultaneous promotion with CeO₂ and ZrO₂ has great influence on the amount of coke and the catalyst service time. XRD analyses indicate that formation of crystalline Ce_xZr_1−xO₂ mixed oxide phases occurs on double promotion. In particular, incorporation of low amounts of Zr in the CeO₂ fluorite structure provides stable dry reforming catalysis. As shown with TPR, promotion leads to a higher reduced state of Ni. SEM, XRD and TPR analyses demonstrate that highly dispersed, doubly promoted Ni catalysts with a strong metal-support interaction are essential for stable dry reforming and suppression of the formation of carbon filaments.