Preparation of hybridizing zeolitic imidazolate frameworks with carboxymethylcellulose for adsorption separation of n-hexane/3-methylpentane

A novel ZIF-8-CMC hybrid material was fabricated from the hybridization of ZIF-8 and carboxymethylcellulose (CMC) by impregnation method for n-hexane/3-methylpentane separation. The surface properties of ZIF-8 were tailored by introducing CMC into ZIF-8 nanoparticles. In this work, adsorption separation of n-hexane (nHEX) and 3-methylpentane (3MP) on ZIF-8-CMC were investigated by batch vapor-phase adsorption and liquid-phase breakthrough adsorption. The adsorption selectivity of nHEX/3MP reversed from preferable adsorption of nHEX to preferable adsorption of 3MP upon the increasing of CMC containing in the hybrid materials. As the temperature increases, the adsorption amounts of nHEX and 3MP decrease. With the increasing of CMC contents, the nHEX uptake decreased, the uptake capacity of 3MP increased gradually. For liquid-phase breakthrough adsorption, the dynamic adsorption capacity of nHEX also decreased with the increasing of temperature.     

Epoxidation of propylene by using [π-C5H5NC16H33]3[PW4O16] as catalyst and with hydrogen peroxide generated by 2-ethylanthrahydroquinone and molecular oxygen

The epoxidation of propylene catalyzed by a reaction-controlled phase transfer catalyst [π-C₅H₅NC₁₆H₃₃]₃[PW₄O₁₆] is investigated. The H₂O₂ is generated by the oxidation of 2-ethylanthrahydroquinone (EAHQ) with molecular oxygen in the organic solvent. Under mild conditions, the selectivity for propylene oxide, based on propylene, is 95%, and the yield, based on 2-ethylanthrahydroquinone, is 85%. During the epoxidation, the catalytic system is homogeneous. However, after the H₂O₂ is used up, the catalyst can be recovered as a precipitate and can be reused. After the epoxidation reaction, 2-ethylanthraquinone can be regenerated to 2-ethylanthrahydroquinone by catalytic hydrogenation, and no coproduct is produced.     

Separation of CO2/CH4 mixtures with the MIL-53(Al) metal–organic framework

Adsorptive separation of CH₄/CO₂ mixtures was studied using a fixed-bed packed with MIL-53(Al) MOF pellets. Such pellets of MIL-53(Al) were produced using a polyvinyl alcohol binder. As revealed by N₂ adsorption isotherms, the use of polyvinyl alcohol as binder results in a loss in overall capacity of 32%. Separations of binary mixtures in breakthrough experiments were successfully performed at pressures varying between 1 and 8 bar and different mixture compositions. The binary adsorption isotherms reveal a preferential adsorption of CO₂ compared to CH₄ over the whole pressure and concentration range. The separation selectivity was affected by total pressure; below 5 bar, a constant selectivity, with an average separation factor of about 7 was observed. Above 5 bar, the average separation factor decreases to about 4. The adsorption selectivity is affected by breathing of the framework and specific interaction of CO₂ with framework hydroxyl groups. CO₂ desorption can be realised by mild thermal treatment.     

Metal-organic framework Cu3 (BTC)2(H2O)3 catalyzed Aldol synthesis of pyrimidine-chalcone hybrids

A typical metal organic framework, [Cu₃ (BTC)₂(H₂O)₃, BTC = 1,3,5-benzene tricarboxylate] has been used for the synthesis of pyrimidine-chalcones. We have explored a green synthesis of pyrimidine chalcones under Cu₃(BTC)₂ catalysis by Aldol condensation. Easy isolation of product, excellent yield, and recyclable catalyst makes this reaction eco-friendly. The technology was demonstrated to be applicable to the synthesis of a host of chemical hybrids.     

Chemical instability of Cu3(BTC)2 by reaction with thiols

In contrast to Fe(BTC) (BTC: 1,3,5-benzenetricarboxylate), the crystal structure of Cu₃(BTC)₂, a commercial metal organic framework widely used as solid catalyst, collapses when contacted with thiols under mild reaction conditions forming copper nanoparticles.     

Polymers oxidation with VO(acac)2 complex

The introduction of epoxy groups in the polymer backbone is one of the most promising methods of modifying polydienes. In this work the performance of the classical catalytic system VO(acac)₂/tert-butylhydroperoxide was evaluated for the epoxidation of polydienes. The polymers investigated were a hydroxylated poly(butadiene), two polybutadienes with high and with low 1,4-content, a poly(isoprene), and a styrene–butadiene copolymer. The epoxidized polymers were characterized by IR, ¹H and ¹³C NMR and GPC techniques. The vanadium system was active for the epoxidation reaction and the reactivity decreases in the order HTPB>PI>1,4-PB>1,2-PBSBR. The occurrence of secondary reactions to low extension could be detected by the presence of hydroxyl, carbonyl and alcohol signals in the spectra of epoxidized polymers. Incomplete mass recovery (70–90%) was observed probably due to the chain degradation or modification of the polymer polarity.     

Effect of physical mixing of CsCl with Au/Ti-MCM-41 on the gas-phase epoxidation of propene using H2 and O2:: Drastic depression of H2 consumption

Vapor-phase epoxidation of propene using H₂ and O₂ over Au/Ti-MCM-41 with or without a promoter has been investigated at various temperatures and at a space velocity of 4000 h^−1. ml/g (cat). As a promoter, CsCl was impregnated and/or physically (simple mixing) or mechanically (crushed in a mortar) mixed at various concentrations. The support, Ti-MCM-41 (Ti/Si = 3/100), was characterized by XRD, UV-Vis, FT-IR, and specific surface area measurement, whereas Au/Ti-MCM-41 with or without a promoter was characterized by TEM, XPS and ICP techniques before and/or after the catalytic tests. Au/Ti-MCM-41 as such gives propene and H₂ conversions of 3.1 and 47%, respectively, with a PO selectivity of 92% at the reaction temperature of 100°C after 60 min of reaction. Physical mixing of CsCl with Au supported on Ti-MCM-41 reduces H₂ consumption by about 90% and improves propene oxide (PO) selectivity up to 97% at a propene conversion of 1.7%. One constraint is that agglomeration of gold particles is caused by Cl⁻ anions; the mean diameter of Au particles, 2.2 nm, in Au/Ti-MCM-41 increases to about 10–20 nm and some clusters are even larger than 50 nm in size due to direct contact between chloride and Au particles.     

Differences in reactivity of pulverised coal in air (O2/N2) and oxy-fuel (O2/CO2) conditions

The reactivity of four pulverised Australian coals were measured under simulated air (O₂/N₂) and oxy-fuel (O₂/CO₂) environments using a drop tube furnace (DTF) maintained at 1673 K and a thermogravimetric analyser (TGA) run under non-isothermal (heating) conditions at temperatures up to 1473 K. The oxygen concentration, covering a wide and practical range, was varied in mixtures of O₂/N₂ and O₂/CO₂ in the range of 3 to 21 vol.% and 5 to 30 vol.%, respectively. The apparent volatile yield measured in CO₂ in the DTF was greater than in N₂ for all the coals studied. Pyrolysis experiments in the TGA also revealed an additional mass loss in a CO₂ atmosphere, not observed in a N₂ atmosphere, at relatively high temperatures. The coal burnout measured in the DTF at several O₂ concentrations revealed significantly higher burnouts for two coals and similar burnouts for the other two coals in oxy-fuel conditions. TGA experiments with char also revealed higher reactivity at high temperatures and low O₂ concentration. The results are consistent with a char–CO₂ reaction during the volatile yield experiments, but additional experiments are necessary to resolve the mechanisms determining the differences in coal burnout.     

Molecular dynamics simulation of diffusion of O2 and CO2 in amorphous poly(ethylene terephthalate) and related aromatic polyesters

The diffusion of small molecules through polymers is important in many areas of polymer science, such as gas barrier and separation membrane materials, polymeric foams, and in the processing and properties of polymers. Molecular simulation techniques have been applied to study the diffusion of oxygen and dioxide of carbon as small molecule penetrants in models of bulk amorphous poly(ethylene terephthalate) and related aromatic polyesters. A bulk amorphous configuration with periodic boundary conditions is generated into a unit cell whose dimensions are determined for each of the simulated aromatic polyesters in the cell to have the experimental density. The aim for this research is to explore and investigate the diffusion of gases through bulk amorphous poly(ethylene terephthalate) and related aromatic polyesters. The diffusion coefficients for O₂ and CO₂ were determined via NVE molecular dynamics simulations using the Dreiding 2.21 molecular mechanics force field over a range of temperatures (300, 500 and 600 K) using up to 30 ns simulation time. We have focussed on the influence of the temperature, polymer dynamics, number of aromatic rings, ortho-, meta-, para-isomers, density and free volume distribution on the diffusion properties. Correlation of diffusion coefficients with free volume, temperature, number of aromatic rings, ortho-, meta- and para-isomers was found.     

Impact of surface mobility in selective oxidation. Isotopic exchange of O2 with O2 on various oxides: MoO3, SnO2 and Sb2O4. Effect of a reducer gas

Isotopic oxygen exchange experiments were carried out on simple oxides (Sb₂O₄, MoO₃ and SnO₂) and mechanical mixtures of MoO₃ or SnO₂(acceptor phase) with Rh//Al₂O₃ or Sb₂O₄ (donor phase). With Rh//Al₂O₃ a synergy effect is found: the amount of oxygen exchanged on the mixture is higher than the sum of oxygen exchanged on the two separate phases. This is a prove of oxygen mobility between donor and acceptor phases. With Sb₂O₄ this effect is less marked suggesting that the presence of a reducer gas is required. In presence of hydrocarbon, no isotopic exchange is observed: only total oxidation occurs. The presence of Sb₂O₄ decreases the rate of total oxidation by blocking, by oxygen spillover, the most active sites for oxidation.     

A comparison of O2 and CO2 oxidation of glassy carbon surfaces

We have studied the reactive adsorption of O₂ on the edge surface of graphite. At 300°C the efficiency of oxygen uptake showed a strong coverage-dependent reactive adsorption coefficient. In general, the efficiencies were low (< 10⁻⁹) over the majority of the coverage range. In contrast, the uptake of oxygen from O₂ and H₂O on sputter-damaged graphite was far more rapid. Sputter-damaged carbon surfaces exhibit greatly enhanced reactivity and are poor models of edge carbon activity. Thermal stability studies on the resultant oxidized edge graphite surfaces provide information about the energetics of product formation in gasification reactions. CO was the dominant product. A fraction of the oxygen on the surface is very tightly bound with energies greater than 85 kcal/mole. The energy decreases to 70 kcal/mole over a wide coverage range. At the highest attainable coverages representing a small fractional population, the energy decreases further down to 58 kcal/mole. Our results show that increasing the amount of oxygen surface coverage decreases the energy barrier for gaseous CO formation but increases the barrier for O₂ dissociation.     

Molecular dynamics simulation of diffusion of O2 and CO2 in blends of amorphous poly(ethylene terephthalate) and related polyesters

The diffusion of small molecules through polymers is important in many areas of polymer science, such as gas barrier and separation membrane materials, polymeric foams, and in the processing and properties of polymers. Molecular dynamics simulation techniques have been applied to study the diffusion of oxygen and carbon dioxide as small molecule penetrants in models polyester blends of bulk amorphous poly(ethylene terephthalate) and related aromatic polyesters. A bulk amorphous configuration with periodic boundary conditions was generated into a unit cell whose dimensions were determined for each of the simulated polyester blends in the cell having the experimental density. The diffusion coefficients for O₂ and CO₂ were determined via NVE molecular dynamics simulations using the Dreiding 2.21 molecular mechanics force field over a range of temperatures (300, 500 and 600 K) using up to 40 ns simulation time. We have focussed on the influence of the temperature, polymer dynamics, density and free volume distribution on the diffusion properties. Correlation of diffusion coefficients with free volume distribution was found.     

Direct growth of Cu3(BTC)2(H2O)3 · xH2O thin films on modified QCM-gold electrodes – Water sorption isotherms

The preparation of a thin film of the metal–organic framework Cu₃(BTC)₂(H₂O)₃ · xH₂O (HKUST-1) on the gold electrode of a quartz-crystal microbalance (QCM) was achieved by direct growth on a 11-mercaptoundecanol self-assembled monolayer (SAM). The formation of the SAM on the gold substrate was proven via reflection–absorption infrared-spectroscopy. The HKUST-1 thin film was characterized by X-ray diffraction, Raman-spectroscopy, and scanning-electron microscopy. Water vapor sorption measurements allow us to directly characterize the sorption properties of the thin film grown on the electrode of the QCM-device.     

A CO and CO2 tolerating (La0.9Ca0.1)2(Ni0.75Cu0.25)O4+d Ruddlesden-Popper membrane for oxygen separation

A series of novel dense mixed conducting ceramic membranes based on K₂NiF₄-type (La_1–xCa_x)₂ (Ni_0.75Cu_0.25)O_4+δ was successfully prepared through a sol-gel route. Their chemical compatibility, oxygen permeability, CO and CO₂ tolerance, and long-term CO₂ resistance regarding phase composition and crystal structure at different atmospheres were studied. The results show that higher Ca contents in the material lead to the formation of CaCO₃. A constant oxygen permeation flux of about 0.63 mL·min⁻¹·cm⁻² at 1173 K through a 0.65 mm thick membrane was measured for (La_0.9Ca_0.1)₂ (Ni_0.75Cu_0.25)O_4+δ, using either helium or pure CO₂ as sweep gas. Steady oxygen fluxes with no sign of deterioration of this membrane were observed with increasing CO₂ concentration. The membrane showed excellent chemical stability towards CO₂ for more than 1360 h and phase stability in presence of CO for 4 h at high temperature. In addition, this membrane did not deteriorate in a high-energy CO₂ plasma. The present work demonstrates that this (La_0.9Ca_0.1)₂(Ni_0.75Cu_0.25)O_4+δ membrane is a promising chemically robust candidate for oxygen separation applications.     

Study on the epoxidation of olefins with H2O2 catalyzed by biquaternary ammonium phosphotungstic acid

Selective epoxidation of olefins is an important field in chemical industry. In this work, we developed a new phosphotungstic acid catalyst {[(C₈H₁₇)(CH₃)₂N]₂(CH₂)₃}_1.5{PO₄[WO(O₂)₂]₄} with long carbon chain and biquaternary ammonium cation. Cyclohexene could be epoxidized to cyclohexene oxide in 96.3% conversion and 98.2% selectivity. The catalyst type, solvent type...     

Synthesis of (C5H5)2Zr(O2C)CH3 and (C5H5)2Zr(O2C)CH2CH3 for olefin polymerization

Summary (C₅H₅)₂Zr(O₂C)CH₃ and (C₅H₅)₂Zr(O₂C)CH₂CH₃ complexes were synthesized, characterized and activated with MAO for ethylene polymerization. The highest catalytic activity was achieved at Al/Zr molar ratio of 3000 for both systems. The effects of the size of the R group in the carboxylate ligands, the Al/Zr molar ratio and reaction temperature on the catalytic activity and polymer properties were studied and discussed.     

A novel (3,4,8)-connected 3D topology framework based on [Gd2(bpdc)3(H2O)3] second building units

A new 3D coordination polymer {[Gd₂(bpdc)₃(H₂O)₃]·H₂O}_n(1) has been isolated from the reaction of 2,2′-bipyridine-4,4′-dicarboxylic acid (H₂bpdc) and Gd(III) salts under hydrothermal conditions. Single-crystal X-ray diffraction study shows that compound 1 is constructed from Gd₂-based second building units (SBUs) [Gd₂(bpdc)₃(H₂O)₃] and displays a 3D (3,4,8)-connected net with (4²·6)(3²·4²·5²)(3²·4⁵·5⁴·6¹¹·7⁶) topology. A thermogravimetric analysis of 1 shows a high thermal stability. The magnetic behavior of 1 reveals a weak antiferromagnetic interaction between Gd(III) ions.     

Fabrication and characterization of (Pb(Mg1/3Nb2/3)O3, Pb(Yb1/2Nb1/2)O3, PbTiO3) ternary system ceramics

New ternary compositions in the Pb(Mg_1/3Nb_2/3)O₃-Pb(Yb_1/2Nb_1/2)O₃–PbTiO₃ (PMN-PYbN-PT) system were prepared using 0.5Pb(Yb_1/2Nb_1/2)O₃-0.5PbTiO₃ (PYbNT) and (1-x)Pb(Mg_1/3Nb_2/3)O₃–xPbTiO₃ (x = 0.26; PMNT26 or x = 0.325; PMNT32.5) powders synthesized via the columbite method. Dense (≥ 96% of theoretical density) ceramics with PMN/PYbN mole ratios of 25/75 (R-25), 50/50 (R-50) and 75/25 (R-75T and R-75R) were fabricated by reactive sintering at 1000 °C for 4 h. Therefore, incorporation of PYbNT to PMNT successfully decreased sintering temperature of PMNT from 1200 °C-1250 °C to 1000 °C. Samples with higher density and perovskite ratio together with lower weight loss possessed higher dielectric and piezoelectric values in each composition. The R-75 samples had remanent polarization (P_r) values of 34-36 μC/cm² and piezoelectric charge coefficient (d₃₃) of 560 pC/N. The sharp phase transition PMNT as a function of temperature became broader or more diffuse with increasing PYbNT content. However, PYbNT addition to PMNT increased Curie temperature (T_c) from 183 °C (for PMNT32.5) to 220-242 °C (for R-75T and R-75R) to 336 °C (for R-25). Therefore, these ternary compositions can be tailored for various high temperature applications due to the relatively higher T_c with enhanced piezoelectric and dielectric properties as compared to PMNT.     

Effects of addition of Pb(Y1/2Nb1/2)O3 (PYN) on microstructure and piezoelectric properties of Pb(Zr0.53Ti0.47)O3

Pure and Pb(Y_1/2Nb_1/2)O₃ (PYN)-doped Pb(Zr_0.53Ti_0.47)O₃ have been characterized. The samples were prepared by conventional mixed-oxide ceramic technology. PYN dopant was added to PZT at content levels ranging from 1 to 2.5 mol%. The microstructures of the samples were examined using SEM and TEM. The average grain size was observed to decrease as the dopant content increased. Herringbone-like and wedge-shaped domain patterns were observed in all the samples. The piezoelectric properties of PZT were greatly improved by the addition of PYN. The highest piezoelectric constant d₃₁ was nearly twice that of pure PZT.     

Structure and dielectric behavior of (1-x)Pb(Sc1/2Ta1/2)O3-xPb(In1/2Nb1/2)O3 solid solution

A solid solution system of (1-x)Pb(Sc_1/2Ta_1/2)O₃-xPb(In_1/2Nb_1/2)O₃ (x = 0.2, 0.4, 0.6, and 0.8) was synthesized by conventional solid-state reaction technique. The optimum sintering temperatures of ceramics with x = 0.2, 0.4, 0.6, and 0.8 were 1400?°C, 1400?°C, 1300?°C, and 1200?°C, respectively. At these temperatures, the densest samples and the maximum dielectric constant were obtained. With increasing x, the percentage of pyrochlore phase increased, indicating a decrease in the solubility of solid solution. For x = 0.2, with the sintering temperature increasing, the ordering degree decreased while the dielectric constant increased. For x = 0.6 and 0.8, at the highest sintering temperature, the most pyrochlore phase appeared and the minimum dielectric constant was obtained. In addition, the relaxor characteristics of solid solution ceramics were systematically investigated. It was found that the dielectric maximum decreased and the temperature at dielectric maximum shifted to higher temperature with x increasing. All compositions exhibited the second-order phase transition due to the analysis of dielectric behaviors on heating and cooling. Interestingly, the difference in dielectric maximum between heating and cooling became larger with PIN content increasing. The diffuseness exponents of all compositions were calculated to be in the range of 1.53–1.66, suggesting the typical relaxor. The polarization-electric field (P-E) hysteresis loops of all solid solutions showed the shapes of slim loop. Meanwhile, the coercive field and remnant polarization of all compositions were analyzed in detail.