Transesterification of palm oil on KyMg1 − xZn1 + xO3 catalyst: Effect of Mg-Zn interaction

The Mg-Zn interaction effect of K_yMg_1 − xZn_1 + xO₃ heterogeneous type catalyst and its performance on transesterification of palm oil have been studied using the response surface methodology and the factorial design of experiments. The catalyst was synthesized using the co-precipitation method and the activity was assessed by transesterification of palm oil into fatty acid methyl esters. The ratio of the Mg/Zn metal interaction, temperature and time of calcination were found to have positive influence on the conversion of palm oil to fatty acid methyl ester (FAME) with the effect of metal to metal ratio and temperature of calcination being more significant. The catalytic activity was found to decrease at higher calcination temperature and the catalyst type K₂Mg_0.34Zn_1.66O₃ with Mg/Zn ratio of 4.81 gave FAME content of 73% at a catalyst loading of 1.404 wt.% of oil with molar ratio of methanol to oil being 6:1 at temperature of 150 °C in 6 h. A regression model was obtained to predict conversions to methyl esters as a function of metal interaction ratio, temperature of calcination and time. The observed activity of the synthesized catalyst was due to its synergetic structure and composition.     

Preparation of Ni/MgxTi1 − xO catalysts and investigation on their stability in tri-reforming of methane

Ni/Mg_xTi_1 − xO catalysts were prepared through a wet impregnation method by dispersing Ni on Mg_xTi_1 − xO composite oxides obtained via a sol–gel technique. The Ni/Mg_xTi_1 − xO catalysts were characterized by various means including ICP–OES, BET, XRD, H₂–TPR, SEM, and TG. No free NiO peak was found in all XRD patterns of the Ni/Mg_xTi_1 − xO catalysts. The H₂–TPR and chemisorption results indicated that adding Ti to the NiO–MgO system obstructed the formation of solid solution, and thus increased the reducibility of the catalysts. The prepared Mg_xTi_1 − xO composite oxides had the same ability to disperse Ni as TiO₂ and MgO. The tri-reforming (simultaneous oxygen reforming, carbon dioxide reforming, and steam reforming) of methane over Ni/Mg_xTi_1 − xO catalysts was carried out in a fixed bed flow reactor. The conversions of CH₄ and CO₂ can respectively be achieved as high as above 95% and 83% over Ni/Mg_0.75Ti_0.25O catalyst under the reaction conditions. The activity of Ni/Mg_0.75Ti_0.25O and Ni/Mg_0.5Ti_0.5O did not decrease for a reaction period of 50 h, indicating their rather high stability. The experimental results showed that the nature of support, the interaction between metal and support, and the ability to be reduced played an important role in improving the stability of catalysts.     

Ethanol steam reforming reactions over Al2O3 · SiO2-supported Ni-La catalysts

Nickel-based catalysts supported on Al₂O₃ · SiO₂ were prepared with modification of the second metal involving La, Co, Cu, Zr or Y, of which the catalytic behaviors were assessed in the ethanol steam reforming reaction. Activity test indicated that addition of La resulted in higher selectivity of hydrogen and lower selectivity of carbon monoxide, compared with Co-doped nickel catalyst. Influences of lanthanum amounts on catalytic performance were studied over 30NixLa/Al₂O₃ · SiO₂ (x = 5, 10, 15), and characterizations by XRD, TPR and XPS indicated that low amount of lanthanum additives (5%) was superior to inhibit the crystal growth of nickel as well as beneficial to the reduction of nickel oxide. Finally 100 h test for the optimal catalyst 30Ni5La/Al₂O₃ · SiO₂ indicated its good long-term stability to provide high hydrogen selectivity and low carbon monoxide formation, as well as good resistance to coke deposition at low temperature.     

Phase equilibria and glass formation studies in the (1 − x)TeO2-xCdO (0.05 ≤ x ≤ 0.33 mol) system

Phase equilibria and glass formation studies of the (1 − x)TeO₂-xCdO system (0.05 ≤ x ≤ 0.33 mol) were realized by using differential thermal analysis (DTA), X-ray diffraction (XRD) and scanning electron microscopy (SEM) techniques. The samples were prepared by applying a conventional melt-quenching technique at 800 °C. The glass formation range of the system was determined as 0.05 ≤ x < 0.15 and the sample containing 10 mol% CdO showed the highest glass stability. Crystallization behavior of the TeO₂-CdO glasses was investigated and formation and/or transformation of different phases were detected for each crystallization reaction. In order to obtain thermal stability of the system, as-cast samples were heat-treated above all crystallization reaction temperatures at 550 °C for 24 h. A binary eutectic: liquid → TeO₂ + CdTe₂O₅ was detected at 638 ± 4 °C. Crystallization behavior of the TeO₂-CdO glasses and microstructural characterization of the TeO₂-CdTe₂O₅ system was realized.     

Microwave dielectric properties of the (1 − x)Mg2TiO4-xCaTiO3-y wt.% ZnNb2O6 ceramics system

Composite ceramics based on (1 − x)Mg₂TiO₄-xCaTiO₃-y wt.% ZnNb₂O₆ (x = 0.12-0.16, y = 0-8) were prepared by a conventional mixed-oxide route. Zn²⁺ partially replaced Mg²⁺ in Mg₂TiO₄ and formed the spinel-structured (Mg_1−δZn_δ)₂TiO₄ phase. Nb²⁺, is known to be solid soluble in CaTiO₃, was found to change its shape from cubic to pliable. A bi-phase system (Mg_1−δZn_δ)₂TiO₄ and CaTiO₃ exhibited in all samples, where a small amount of second phase Mg_1−δZn_δTiO₃ was also detected. The microwave dielectric properties of specimens were strongly related to ZnNb₂O₆ and CaTiO₃ content. As y increased, ?_r and τ_f decreased, however, Q × f decreased to a minimum value and started to increase thereafter. It was also found that ?_r and τ_f increased and Q × f decreased with increasing x. The optimized microwave dielectric properties with ?_r = 18.37, Q × f = 31,027 GHz (at 6 GHz), and τ_f = 0.51 ppm/°C were achieved for (1 − x)Mg₂TiO₄-xCaTiO₃-y wt.% ZnNb₂O₆ (x = 0.12, y = 4) sintered at 1360 °C for 6 h.     

Preparation, characterization and electrical conductivity studies of NdYb1−xGdxZr2O7 (0 ≤ x ≤ 1.0) ceramics

Several compositions of NdYb_1−xGd_xZr₂O₇ (0 ≤ x ≤ 1.0) ceramics were prepared by pressureless-sintering method at 1973 K for 10 h in air. The relative density, microstructure and electrical conductivity of NdYb_1−xGd_xZr₂O₇ ceramics were analyzed by the Archimedes method, X-ray diffraction, scanning electron microscopy and impedance plots measurements. NdYb_1−xGd_xZr₂O₇ (0 ≤ x ≤ 0.3) ceramics have a single phase of defect fluorite-type structure, and NdYb_1−xGd_xZr₂O₇ (0.7 ≤ x ≤ 1.0) ceramics exhibit a single phase of pyrochlore-type structure; however, the NdYb_0.5Gd_0.5Zr₂O₇ composition shows mixed phases of both defect fluorite-type and pyrochlore-type structures. The measured values of the grain conductivity obey the Arrhenius relation. The grain conductivity of each composition in NdYb_1−xGd_xZr₂O₇ ceramics gradually increases with increasing temperature from 673 to 1173 K. NdYb_1−xGd_xZr₂O₇ ceramics are oxide-ion conductor in the oxygen partial pressure range of 1.0 × 10⁻⁴ to 1.0 atm at all test temperature levels. The highest grain conductivity value obtained in this work is 1.79 × 10⁻² S cm⁻¹ at 1173 K for NdYb_0.3Gd_0.7Zr₂O₇ composition.     

Synthesis and transport properties in La2−xAxMo2O9−δ (A = Ca, Sr, Ba, K) series

The La_2−xA_xMo₂O_9−δ (A = Ca²⁺, Sr²⁺, Ba²⁺ and K⁺) series has been synthesised as nanocrystalline materials via a modification of the freeze-drying method. The resulting materials have been characterised by X-ray diffraction (XRD), thermal analysis (TG/DTA, DSC), scanning electron microscopy (SEM) and high-resolution transmission electron microscopy (HRTEM). The high-temperature β-polymorph is stabilised for dopant content x > 0.01. The nanocrystalline powders were used to obtain dense ceramic materials with optimised microstructure and relative density >95%. The overall conductivity determined by impedance spectroscopy depends on both the ionic radius and dopant content. The conductivity decreases slightly as the dopant content increases in addition a maximum conductivity value was found for Sr²⁺ substitution, which show an ionic radii slightly higher than La³⁺ (e.g. 0.08 S cm⁻¹ for La₂Mo₂O₉ and 0.06 S cm⁻¹ for La_1.9Sr_0.1Mo₂O_9−δ at 973 K). The creation of extrinsic vacancies upon substitution results in a wider stability range under reducing conditions and prevents amorphisation, although the stability is not enhanced significantly when compared to samples with higher tungsten content. These materials present high thermal expansion coefficients in the range of (13-16) × 10⁻⁶ K⁻¹ between room temperature and 753 K and (18-20) × 10⁻⁶ K⁻¹ above 823 K. The ionic transport numbers determined by a modified emf method remain above 0.98 under an oxygen partial pressure gradient of O₂/air and decreases substantially under wet 5% H₂-Ar/air when approaching to the degradation temperature above 973 K due to an increase of the electronic contribution to the overall conductivity.     

Evolution of the local structure and electrochemical properties of spinel LiNixMn2−xO4 (0 ≤ x ≤ 0.5)

A series of Ni substituted spinel LiNi_xMn_2−xO₄ (0 ≤ x ≤ 0.5) have been synthesized to study the evolution of the local structure and their electrochemical properties. X-ray diffraction showed a few Ni cations moved to the 8a sites in heavily substituted LiNi_xMn_2−xO₄ (x ≥ 0.3). X-ray photoelectron spectroscopy confirmed Ni²⁺ cations were partially oxidized to Ni³⁺. The local structures of LiNi_xMn_2−xO₄ were studied by analyzing the and A_1g Raman bands. The most compact [Mn(Ni)O₆] octahedron with the highest bond energy of Mn(Ni)O was found for LiNi_0.2Mn_1.8O₄, which showed a Mn(Ni)O average bond length of 1.790 Å, and a force constant of 2.966 N cm⁻¹. Electrolyte decomposition during the electrochemical charging processes increased with Ni substitution. The discharge capacities at the 4.1 and 4.7 V plateaus obeyed the linear relationships with respect to the Ni substitution with the slopes of −1.9 and +1.9, which were smaller than the theoretical values of −2 and +2, respectively. The smaller slopes could be attributed to the electrochemical hysteresis and the presence of Ni³⁺ in the materials.     

Ethanol electrooxidation on novel carbon supported Pt/SnOx/C catalysts with varied Pt:Sn ratio

Novel carbon supported Pt/SnO_x/C catalysts with Pt:Sn atomic ratios of 5:5, 6:4, 7:3 and 8:2 were prepared by a modified polyol method and characterized with respect to their structural properties (X-ray diffraction (XRD) and transmission electron microscopy (TEM)), chemical composition (XPS), their electrochemical properties (base voltammetry, CO_ad stripping) and their electrocatalytic activity and selectivity for ethanol oxidation (ethanol oxidation reaction (EOR)). The data show that the Pt/SnO_x/C catalysts are composed of Pt and tin oxide nanoparticles with an average Pt particle diameter of about 2 nm. The steady-state activity of the Pt/SnO_x/C catalysts towards the EOR decreases with tin content at room temperature, but increases at 80 °C. On all Pt/SnO_x/C catalysts, acetic acid and acetaldehyde represent dominant products, CO₂ formation contributes 1-3% for both potentiostatic and potentiodynamic reaction conditions. With increasing potential, the acetaldehyde yield decreases and the acetic acid yield increases. The apparent activation energies of the EOR increase with tin content (19-29 kJ mol⁻¹), but are lower than on Pt/C (32 kJ mol⁻¹). The somewhat better performance of the Pt/SnO_x/C catalysts compared to alloyed PtSn_x/C catalysts is attributed to the presence of both sufficiently large Pt ensembles for ethanol dehydrogenation and C-C bond splitting and of tin oxide for OH generation. Fuel cell measurements performed for comparison largely confirm the results obtained in model studies.     

Enhanced luminescence of novel Ca3B2O6:Dy phosphors by Li-codoping for LED applications

The Ca_3−xB₂O₆:xDy³⁺ (0.0 ≤ x ≤ 0.105) and Ca_2.95−yDy_0.05B₂O₆:yLi⁺ (0 ≤ y ≤ 0.34) phosphors were synthesized at 1100 °C in air by solid-state reaction route. The as-synthesized phosphors were characterized by X-ray powder diffraction (XRD), scanning electron microscope (SEM), photoluminescence excitation (PLE) and photoluminescence (PL) spectra. The PLE spectra show the excitation peaks from 300 to 400 nm is due to the 4f-4f transitions of Dy³⁺. This mercury-free excitation is useful for solid state lighting and light-emitting diodes (LEDs). The emission of Dy³⁺ ions upon 350 nm excitation is observed at 480 nm (blue) due to the ⁴F_9/2 → ⁶H_15/2 transitions, 575 nm (yellow) due to ⁴F_9/2 → ⁶H_13/2 transitions and a weak 660 nm (red) due to ⁴F_9/2 → ⁶H_11/2 emissions, respectively. The optimal PL intensity of the Ca_3−xB₂O₆:xDy³⁺ phosphors is found to be x = 0.05. Moreover, the PL results from Ca_2.95−yDy_0.05B₂O₆:yLi⁺ phosphors show that Dy³⁺ emissions can be enhanced with the increasing codopant Li⁺ content till y = 0.22. By simulation of white light, the CIE of the investigated phosphors can be tuned by varying the content of Li⁺ ions, and the optimal CIE value (0.300, 0.298) is realized when the content of Li⁺ ions is y = 0.22. All the results imply that the Ca_2.95−yDy_0.05B₂O₆:yLi⁺ phosphors could be potentially used as white LEDs.     

One-step electrochemical preparation of the ternary (BixSb1−x)2Te3 thin films on Au(1 1 1): Composition-dependent growth and characterization studies

This study reports on the synthesis of ternary semiconductor (Bi_xSb_1−x)₂Te₃ thin films on Au(1 1 1) using a practical electrochemical method, based on the simultaneous underpotential deposition (UPD) of Bi, Sb and Te from the same solution containing Bi³⁺, SbO⁺, and HTeO₂⁺ at a constant potential. The thin films are characterized by X-ray diffraction (XRD), atomic force microscopy (AFM), energy dispersive spectroscopy (EDS) and reflection absorption-FTIR (RA-FTIR) to determine structural, morphological, compositional and optic properties. The ternary thin films of (Bi_xSb_1−x)₂Te₃ with various compositions (0.0 ≤ x ≤ 1.0) are highly crystalline and have a kinetically preferred orientation at (0 1 5) for hexagonal crystal structure. AFM images show uniform morphology with hexagonal-shaped crystals deposited over the entire gold substrate. The structure and composition analyses reveal that the thin films are pure phase with corresponding atomic ratios. The optical studies show that the band gap of (Bi_xSb_1−x)₂Te₃ thin films could be tuned from 0.17 eV to 0.29 eV as a function of composition.     

The promotional effect of Cr on catalytic activity of Pt/ZSM-35 for H2-SCR in excess oxygen

Selective catalytic reduction of NO by hydrogen was studied over Cr modified Pt/ZSM-35 catalysts. The preparation process greatly influenced catalytic activity and sample prepared by co-impregnation method exhibits the best activity. In situ DRIFT studies revealed that on Pt–Cr/ZSM-35, (1) new Pt-NO^δ+ and NO species adsorbed on Pt were detected upon NO + O₂ adsorption; (2) much more ammonia species were formed under reaction condition. Cr addition not only enhanced the adsorption of NO_x but also promoted the formation of surface NH₄⁺ species, which should be the origin of promotional effect of Cr on Pt/ZSM-35 for H₂-SCR reaction.     

Properties of Ni1−xFex (0.1 < x < 0.9) and Invar (x = 0.64) alloys obtained by electrodeposition

Electrodeposition of Ni_1−xFe_x (x = 0.1-0.9) films was carried out from a chloride plating solution containing saccharin as an organic additive at a constant current density (5 mA/cm²) and a controlled pH of 2.5. X-ray diffraction studies revealed the existence of an fcc, or γ phase, in the range of 10-58 wt.% Fe, a mixed fcc/bcc phase in the range of 59-60 wt.% Fe, and a bcc, or α phase in the range of 64-90 wt.% Fe. The saturation magnetization, B_s, of electrodeposited Ni_1−xFe_x alloys at the room temperature was found to increase with the increase of Fe-content and follows the Slater-Pauling curve, but deviates from as-cast bulk NiFe alloys. The coefficient of thermal expansion, CTE, of electrodeposited alloys at room temperature also deviates from as-cast bulk NiFe alloys. Annealing of α-Ni₃₆Fe₆₄ alloy results in a martensitic α → γ phase transformation, which takes place between 300 and 400 °C. It was demonstrated that thermal treatment above 400 °C was necessary to obtain magnetic and mechanical properties similar to those to conventional Invar alloy. Annealing of α-Ni₃₆Fe₆₄ alloy at 700 °C brings about a decrease of B_s from 1.75 to 0.45 T. By controlling the annealing conditions of α → γ martensitic transformation, it is possible to adjust the CTE of Ni₃₆Fe₆₄ alloy over the broad limits from 2.7 to 8.7 × 10⁻⁶/°C.     

Zr-doped Li[Ni0.5−xMn0.5−xZr2x]O2 (x = 0, 0.025) as cathode material for lithium ion batteries

Layered Li[Ni_0.5−xMn_0.5−xZr_2x]O₂ (x = 0, 0.025) have been prepared by the mixed hydroxide and molten-salt synthesis method. The individual particles of synthesized materials have a sub-microsize range of 200-500 nm, and LiNi_0.475Mn_0.475Zr_0.05O₂ has a rougher surface than that of LiNi_0.5Mn_0.5O₂. The Li/Li[Ni_0.5−xMn_0.5−xZr_2x]O₂ (x = 0, 0.025) electrodes were cycled between 4.5 and 2.0 V at a current density of 15 mA/g, the discharge capacity of both cells increased during the first ten cycles. The discharge capacity of the Li/LiNi_0.475Mn_0.475Zr_0.05O₂ cell increased from 150 to 220 mAh/g, which is 50 mAh/g larger than that of the Li/LiNi_0.5Mn_0.5O₂ cell. We found that the oxidation of oxygen and the Mn³⁺ ion concerned this phenomenon from the cyclic voltammetry (CV). Thermal stability of the charged Li[Ni_0.5−xMn_0.5−xZr_2x]O₂ (x = 0, 0.025) cathode was improved by Zr doping.     

Enhanced thermoelectric properties induced by chemical pressure in Ca3Co4O9

We report the investigation of boron substitution on structural, electrical, thermal, and thermoelectric properties of Ca_3−xB_xCo₄O₉ (x=0, 0.5, 0.75, and 1) in the temperature range between 300 K and 5 K. X-ray diffraction studies show that the Ca₃Co₄O₉ phase is successfully preserved as the majority phase in the x=0.5 sample despite the small size of boron ions. Electrical transport measurements confirm that B³⁺ substitution for Ca²⁺ causes an increase in resistivity due to the decrease in carrier concentration. x=0.5 sample is found to have a Seebeck coefficient of 181 μV/K at room temperature which is ~1.5 times higher than that of the pure Ca₃Co₄O₉. Our results indicate that the chemical pressure due to the large ionic radii difference between B³⁺ (0.27 Å) and Ca²⁺ (1 Å) enhances the thermoelectric properties as long as the unique crystal structure of Ca₃Co₄O₉ is preserved.     

Electrochemical and thermal studies of Li[NixLi(1/3−2x/3)Mn(2/3−x/3)]O2 (x = 1/12, 1/4, 5/12, and 1/2)

Samples of the layered cathode materials, Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂ (x = 1/12, 1/4, 5/12, and 1/2), were synthesized at 900 °C. Electrodes of these samples were charged in Li-ion coin cells to remove lithium. The charged electrode materials were rinsed to remove the electrolyte salt and then added, along with EC/DEC solvent or 1 M LiPF₆ EC/DEC, to stainless steel accelerating rate calorimetry (ARC) sample holders that were then welded closed. The reactivity of the samples with electrolyte was probed at two states of charge. First, for samples charged to near 4.45 V and second, for samples charged to 4.8 V, corresponding to removal of all mobile lithium from the samples and also concomitant release of oxygen in a plateau near 4.5 V. Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂ samples with x = 1/4, 5/12 and 1/2 charged to 4.45 V do not react appreciably till 190 °C in EC/DEC. Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂ samples charged to 4.8 V versus Li, across the oxygen release plateau, start to significantly react with EC/DEC at about 130 °C. However, their high reactivity is similar to that of Li_0.5CoO₂ (4.2 V) with 1 μm particle size. Therefore, Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂ samples showing specific capacity of up to 225 mAh/g may be acceptable for replacing LiCoO₂ (145 mAh/g to 4.2 V) from a safety point of view, if their particle size is increased.     

Synthesis and characterization of MoOx-Pt/C and TiOx-Pt/C nano-catalysts for oxygen reduction

The oxygen reduction reaction (ORR) was studied at carbon supported MoO_x-Pt/C and TiO_x-Pt nanocatalysts in 0.5 mol dm⁻³ HClO₄ solution, at 25 °C. The MoO_x-Pt/C and TiO_x-Pt/C catalysts were prepared by the polyole method combined by MoO_x or TiO_x post-deposition. Home made catalysts were characterized by TEM and EDX techniques. It was found that catalyst nanoparticles were homogenously distributed over the carbon support with a mean particle size about 2.5 nm. Quite similar distribution and particle size was previously obtained for Pt/C catalyst. Results confirmed that MoO_x and TiO_x post-deposition did not lead to a significant growth of the Pt nanoparticles.The ORR kinetics was investigated by cyclic voltammetry and linear sweep voltammetry at the rotating disc electrode. These results showed the existence of two E − log j regions, usually observed with polycrystalline Pt in acid solution. It was proposed that the main path in the ORR mechanism on MoO_x-Pt/C and TiO_x-Pt/C catalysts was the direct four-electron process with the transfer of the first electron as the rate-determining step. The increase in catalytic activity for ORR on MoO_x-Pt/C and TiO_x-Pt/C catalysts, in comparison with Pt/C catalyst, was explained by synergetic effects due to the formation of the interface between the platinum and oxide materials and by spillover due to the surface diffusion of oxygen reaction intermediates.     

La1−xSrxFeO3−δ perovskites as redox materials for application in a membrane reactor for simultaneous production of pure hydrogen and synthesis gas

This work reports on the preparation and characterization of perovskitic materials with the general formula La_1−xSr_xFeO₃ (x = 0, 0.3, 0.7, 1) for application in a dense mixed conducting membrane reactor process for simultaneous production of synthesis gas and pure hydrogen. Thermogravimetric experiments indicated that the materials are able to loose and uptake reversibly oxygen from their lattice up to 0.2 oxygen atoms per “mole” for SrFeO₃ with x = 1 at 1000 °C. The capability of the prepared powders to convert CH₄ during the reduction step, in order to produce synthesis gas, as well as their capability to dissociate water during the oxidation step, in order to produce hydrogen were evaluated by pulse reaction experiments in a fixed bed pulse reactor. The high sintering temperatures (1100-1300 °C) required for the densification of the membrane materials result in decreased methane conversion and H₂ yields during the reduction step compared to the corresponding values obtained with the perovskite powders calcined at 1000 °C. Addition of small quantities of NiO, by simple mechanical mixing, to the perovskites after their sintering at high temperatures, increases substantially both their methane decomposition reactivity, their selectivity towards CO and H₂ and their water splitting activity. Maximum H₂ yield during the reduction step is achieved with the La_0.7Sr_0.3FeO₃ sample mixed with 5% NiO and is 80% of the theoretically expected H₂, based on complete methane decomposition. In the oxidation - water splitting step, 912 μmol H₂ per gr solid are produced with the La_0.3Sr_0.7FeO₃ sample mixed with 5% NiO. The experimental results of this work can be equally well applied for the “chemical-looping reforming” process since they concern using the lattice oxygen of the perovskite oxides for methane partial oxidation to syngas, in the absence of molecular oxygen, and subsequent oxidation of the solid.     

Structural and electrochemical behaviors of metastable Li2/3[Ni1/3Mn2/3]O2 modified by metal element substitution

Layered metastable lithium manganese oxides, Li_2/3[Ni_1/3−xMn_2/3−yM_x+y]O₂ (x = y = 1/36 for M = Al, Co, and Fe and x = 2/36, y = 0 for M = Mg) were prepared by the ion exchange of Li for Na in P2-Na_2/3[Ni_1/3−xMn_2/3−yM_x+y]O₂ precursors. The Al and Co doping produced the T^#2 structure with the space group Cmca. On the other hand, the Fe and Mg doped samples had the O6 structure with space group R-3m. Electron diffraction revealed the 1:2 type ordering within the Ni_1/3−xMn_2/3−yM_x+yO₂ slab. It was found that the stacking sequence and electrochemical performance of the Li cells containing T^#2-Li_2/3[Ni_1/3Mn_2/3]O₂ were affected by the doping with small amounts of Al, Co, Fe, and Mg. The discharge capacity of the Al doped sample was around 200 mAh g⁻¹ in the voltage range between 2.0 and 4.7 V at the current density of 14.4 mA g⁻¹ along with a good capacity retention. Moreover, for the Al and Co doped and undoped oxides, the irreversible phase transition of the T^#2 into the O2 structure was observed during the initial lithium deintercalation.     

Development of ceramic electrochemical sensor based on Bi2Ru2O7+x − RuO2 sub-micron oxide sensing electrode for water quality monitoring

Sub-micron Bi₂Ru₂O_7+x + RuO₂ oxide sensing electrodes (SE) for water quality sensors were prepared on platinised ceramic substrate of the sensor. Their morphology was analysed by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy-dispersive X-ray analysis (EDX). Sensing properties of the Bi₂Ru₂O_7+x + RuO₂-SE were investigated for potentiometric detection of pH and dissolved oxygen (DO) in water in the temperature range of 4–30 °C. Sensor was capable to measure DO from 0.5 to 8.0 ppm and pH from 2.0 to 13.0, respectively. The obtained results show acceptable linearity of the measuring characteristics. Long-term stability trial for Bi₂Ru₂O_7+x + RuO₂-SE revealed that bio-fouling can be one of the main destructive factors affecting the performance of the sensors in the long run. The screen-printing technology used in the multi-sensory implementation provides fundamental properties of miniaturization, reasonable accuracy and low cost.