Electrospun Cu-doped ZnO nanofibers for H2S sensing

Pure and Cu-doped ZnO nanofibers were synthesized via electrospinning technology. The morphology and structure of the as-synthesized nanofibers were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD) and Raman spectroscopy. The effects of Cu doping on H₂S sensing properties at low concentration (1-10 ppm) were investigated at 230 °C. The results show that the H₂S sensing properties of ZnO nanofibers are effectively improved by Cu doping: 6 at% Cu-doped ZnO nanofibers show a maximum sensitivity to H₂S gas, and the response to 10 ppm H₂S is one order of magnitude higher than the one of pure ZnO nanofibers.     

Electrostatic sprayed SnO2 and Cu-doped SnO2 films for H2S detection

This paper presents the ability of electrostatic sprayed tin oxide (SnO₂) and tin oxide doped with copper oxide (1, 2, and 4 at.% Cu) films to detect different pollutant gases, i.e., H₂S, SO₂, and NO₂. The influence of a copper oxide dopant on the SnO₂ morphology is studied using scanning electron microscopy (SEM) technique, which reveals a small decrease in the porosity and particle size when the amount of dopant is increased. The sensing properties of the SnO₂ films are greatly improved by doping, i.e., the Cu-doped SnO₂ films have large response to low concentration (10 ppm) of H₂S at low operating temperature (100 °C). Furthermore, no cross-sensitivity to 1 ppm NO₂ and 20 ppm SO₂ is observed. Among the studied films, the 1 at.% Cu-doped SnO₂ layer is the most sensitive in the detection of all the studied gases.     

Enhanced H2S sensing characteristics of SnO2 nanowires functionalized with CuO

The CuO-functionalized SnO₂ nanowire (NW) sensors were fabricated by depositing a slurry containing SnO₂ NWs on a polydimethylsiloxane (PDMS)-guided substrate and subsequently dropping Cu nitrate aqueous solution. The CuO coating increased the gas responses to 20 ppm H₂S up to 74-fold. The R_a/R_g value of the CuO-doped SnO₂ NWs to 20 ppm H₂S was as high as 809 at 300 °C, while the cross-gas responses to 5 ppm NO₂, 100 ppm CO, 200 ppm C₂H₅OH, and 100 ppm C₃H₈ were negligibly low (1.5–4.0). Moreover, the 90% response times to H₂S were as short as 1–2 s at 300–400 °C. The selective detection of H₂S and enhancement of the gas response were attributed to the uniform distribution of the sensitizer (CuO) on the surface of the less agglomerated network of the SnO₂ NWs.     

Nano particulate SnO2 based resistive films as a hydrogen and acetone vapour sensor

SnCl₂ (solution) was spin coated on soda lime glass and Al₂O₃ substrate to obtain nano-particulate tin oxide film, directly by sintering at 550 °C for 40 minutes (min). The surface morphology and crystal structure of the tin oxide films were analyzed using atomic force microscopy (AFM) and X-ray diffraction (XRD). The size of SnO₂ nanostructure was determined from UV-vis and found to be ?3 nm. These films were tested for sensing H₂ concentration of 0.1-1000 ppm at optimized operating temperature of 265 °C. The results showed that sensitivity (R_air/R_gas per ppm) goes on increasing with decreasing concentration of test gas, giving concentration dependent changes. Special studies carried out at low concentration levels (0.1-1 and 1-10 ppm) of H₂, give high sensitivity (200 × 10⁻³/ppm) for lowest concentration (0.1-1 ppm) of H₂. The selectivity for H₂ against relative humidity (RH), CO₂, CO and LPG gases is also good. The sensor, at operating temperature of 200 °C, is showing nearly zero response to 300 ppm of H₂, and offering response to acetone vapour of 11 ppm. Selectivity for acetone against RH% and CO₂ was also studied. These sensors can be used as H₂ sensor at an operating temperature of 265 °C, and as an acetone sensor at the operating temperature of 200 °C.     

Necked ZnO nanoparticle-based NO2 sensors with high and fast response

The NO₂ gas sensing characteristics of semiconductor type gas sensors with channels composed of necked ZnO nanoparticles (NPs) were investigated in this study. The heat treatment of the NPs at 400 °C led to their necking and coarsening. The response of the necked-NP-based sensors was as high as 100 when exposed to 0.2 ppm of NO₂ at 200 °C. As the concentration of NO₂ increased to 5 ppm, their response was enhanced to approximately 400. During the repeated injection of NO₂ gas with a concentration of 0.4 ppm, the sensors exhibited stable response characteristics. Furthermore, the 90% response and recovery times of the gas sensor were as fast as 13 and 10 s, respectively. These observations indicate that the non-agglomerated necking of the NPs induced by the heat treatment significantly enhances the gas sensing characteristics of the NP-based gas sensors.     

Highly sensitive SnO2 thin film with low operating temperature prepared by sol–gel technique

Sol–gel dip coating technique was employed to prepare Cu-doped SnO₂ thin films, which were able to detect H₂S gas at room temperature with high sensitivity and revealed fast response characteristics. The highest sensor response (the ratio of resistance in air versus in H₂S) was 3648 under H₂S concentration of 68.5 ppm at room temperature. Recoverability of the thin films appeared when the temperature raised to 50 °C. The films were analyzed by means of XRD and the dried gel powder was studied by TG-DTA test. Influences of sintering temperature and doping level on the H₂S response are discussed. The average grain size of the SnO₂ was about 25 nm.     

Electrical response of Sm2O3-doped SnO2 to C2H2 and effect of humidity interference

Pure and Sm₂O₃-doped SnO₂ are prepared through a sol–gel method and characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). The sensor based on 6 wt% Sm₂O₃-doped SnO₂ displays superior response at an operating temperature of 180 °C, and the response magnitude to 1000 ppm C₂H₂ can reach 63.8, which is 16.8 times larger than that of pure SnO₂. This sensor also shows high sensitivity under various humidity conditions. These results make our product be a good candidate in fabricating C₂H₂ sensors.     

Tetrakis(alkylthio)-substituted lutetium bisphthalocyanines for sensing NO2 and O3

In this study, the nitrogen dioxide (NO₂) and ozone (O₃) sensing properties of a series bis[tetrakis(alkylthio) phthalocyaninato] lutetium(III) complexes [(C_nH_2n+1S)₄Pc]₂Lu(III) (n = 6, 10, 16) are investigated as a function of concentration in the temperature range between 25 °C and 150 °C. The concentration ranges were 1–10 ppm for NO₂, and 50 ppb–1 ppm for O₃. The response time and the sensor response to NO₂ are measured for approximately 1 min and 100% ppm⁻¹, respectively, for compound 1 at room temperature. At room temperature, all compounds are in the solid phase. The response time decreases to a few seconds with increasing operation temperature to 150 °C. At this temperature, all compounds are in the liquid crystal phase. The fastest response to oxidizing gases is observed at the liquid crystal phase of the Pcs. It has also been observed that the response time and the sensor response depend on the alkyl chain lengths of the Pcs. The doping effect of oxygen has been determined under high purity nitrogen N₂ flow, after exposure to dry air, at a different period of time and after annealing. It has been found that the conductivities of [(C_nH_2n+1S)₄Pc]₂Lu(III) thin films increased after exposure to dry air and the conduction mechanism also changed from ohmic behavior to space-charge-limited conduction.     

SnO2 thin film sensor with enhanced response for NO2 gas at lower temperatures

Semiconducting SnO₂ thin films having higher value of electrical conductivity have been deposited using RF sputtering technique in the reactive gas environment (30% O₂ + 70% Ar) using a metallic tin (Sn) target for detection of oxidizing NO₂ gas. The effect of growth pressure (12-18 mTorr) on the surface morphology and structural property of SnO₂ film was studied using Atomic force microscopy (AFM), Scanning electron microscopy (SEM) and X-ray Diffraction (XRD) respectively. Film deposited at 16 mTorr sputtering pressure was porous with rough microstructure and exhibits high sensor response (∼2.9 × 10⁴) towards 50 ppm NO₂ gas at a comparatively low operating temperature (∼100 °C). The sensor response was found to increase linearly from 1.31 × 10² to 2.9 × 10⁴ while the response time decrease from 12.4 to 1.6 min with increase in the concentration of NO₂ gas from 1 to 50 ppm. The reaction kinetics of target NO₂ gas on the surface of SnO₂ thin film at the Sn sites play important role in enhancing the response characteristics at lower operating temperature (∼100 °C). The results obtained in the present study are encouraging for realization of SnO₂ thin film based sensor for efficient detection of NO₂ gas with low power consumption.     

Temperature dependent H2S and Cl2 sensing selectivity of Cr2O3 thin films

The conductometric gas sensing characteristics of Cr₂O₃ thin films - prepared by electron-beam deposition of Cr films on quartz substrate followed by oxygen annealing - have been investigated for a host of gases (CH₄, CO, NO₂, Cl₂, NH₃ and H₂S) as a function of operating temperature (between 30 and 300 °C) and gas concentration (1-30 ppm). We demonstrate that these films are highly selective to H₂S at an operating temperature of 100 °C, while at 220 °C the films become selective to Cl₂. This result has been explained on the basis of depletion of chemisorbed oxygen from the surface of films due to temperature and/or interaction with Cl₂/H₂S, which is supported experimentally by carrying out the work function measurements using Kelvin probe method. The temperature dependent selectivity of Cr₂O₃ thin films provides a flexibility to use same film for the sensing of Cl₂ as well as H₂S.     

Fabrication of N-type Fe2O3 and P-type LaFeO3 nanobelts by electrospinning and determination of gas-sensing properties

N-type Fe₂O₃ nanobelts and P-type LaFeO₃ nanobelts were prepared by electrospinning. The structure and micro-morphology of the materials were characterized by X-ray diffraction (XRD) and scanning of electron microscopy (SEM). The gas sensing properties of the materials were investigated. The results show that the optimum operating temperature of the gas sensors fabricated from Fe₂O₃ nanobelts is 285 °C, whereas that from LaFeO₃ nanobelts is 170 °C. Under optimum operating temperatures at 500 ppm ethanol, the response of the gas sensors based on these two materials is 4.9 and 8.9, respectively. The response of LaFeO₃-based gas sensors behaves linearly with the ethanol concentration at 10-200 ppm. Sensitivities to different gases were examined, and the results show that LaFeO₃ nanobelts exhibit good selectivity to ethanol, making them promising candidates as practical detectors of ethanol.     

New gas sensitive MIS structures Pt/Al2O3(M = Pt, Rh)/Si with a granular dielectric layer

New gas sensitive MIS structures Pt/Al₂O₃(M)/p-Si, where M = Pt, Rh, with granular dielectric Al₂O₃ layers doped with noble metals were obtained by an aerosol pyrolysis method. Surface morphology and composition of the structures were studied by TEM, AFM and EPMA. Sensor properties of the MIS structures were studied towards reducing gases (1000 ppm H₂, 300 ppm CO, 1000 ppm CH₄ in air) at 100 and 200 °C. The Pt/Al₂O₃(M = Pt, Rh)/Si structures showed a very high sensor response to reducing gases. A shift of C–V characteristics was up to 2.5 V under CO, 2.2 V under hydrogen and 0.7 V under methane. High values of shift of C–V curves can be related with cooperative influence of a change of surface state density in dielectric layer, reduction of platinum electrode and dipole layer formation.     

Enhanced H2S sensing characteristics of Pt doped SnO2 nanofibers sensors with micro heater

Gas sensors were designed and fabricated using oxide nanofibers as the sensing materials on micro platforms using micromachining technology. Pure and Pt doped SnO₂ nanofibers were prepared by electrospinning and their H₂S gas sensing characteristics were subsequently investigated. The sensing temperatures of 300 and 500 °C could be attained at the heater powers of 36 and 94 mW, respectively, and the sensors showed high and fast responses to H₂S. The responses of 0.08 wt% Pt doped SnO₂ nanofibers to 4-20 ppm H₂S, were 25.9-40.6 times higher than those of pure SnO₂ nanofibers. The gas sensing characteristics were discussed in relation to the catalytic promotion effect of Pt, nano-scale morphology of electrospun nanofibers, and sensor platform using micro heater.     

Improved crystalline structure and H2S sensing performance of CuO-Au-SnO2 thin film using SiO2 additive concentration

In situ SiO₂-doped SnO₂ thin films were successfully prepared by liquid phase deposition. The influence of SiO₂ additive as an inhibitor on the surface morphology and the grain size for the thin film has been investigated. These results show that the morphology of SnO₂ film changes significantly by increasing the concentration of H₂SiF₆ solution which decreases the grain size of SnO₂. The stoichiometric analysis of Si content in the SnO₂ film prepared from various Si/Sn molar ratios has also been estimated. For the sensing performance of H₂S gas, the SiO₂-doped Cu-Au-SnO₂ sensor presents better sensitivity to H₂S gas compared with Cu-Au-SnO₂ sensor due to the fact that the distribution of SiO₂ particles in grain boundaries of nano-crystallines SnO₂ inhibited the grain growth (<6 nm) and formed a porous film. By increasing the Si/Sn molar ratio, the SiO₂-doped Cu-Au-SnO₂ gas sensors (Si/Sn = 0.5) exhibit a good sensitivity (S = 67), a short response time (t_90% < 3 s) and a good gas concentration characteristic (α = 0.6074). Consequently, the improvement of the nano-crystalline structures and high sensitivity for sensing films can be achieved by introducing SiO₂ additive into the SnO₂ film prepared by LPD method.     

Development and application of micromachined Pd/SnO2 gas sensors with zeolite coatings

Zeolite A (LTA)-coated micromachined sensors have been prepared and used in the sensing of individual gases (H₂, CH₄, C₂H₅OH, C₃H₈ and CO, in the 10–1000 ppm range) and gas mixtures. Unlike previous works with conventional sensors, a hydrothermal synthesis was not used to prepare a zeolite film. Instead, a zeolite coating was formed on top of the Pd/SnO₂ surface by microdropping from a zeolite suspension. In spite of this, the response of the sensor with zeolite is significantly different from that of unmodified sensors, and essentially reproduces the performance of zeolite-coated conventional sensors. By avoiding the use of a hydrothermal synthesis the integrity of the sensor is better preserved, and the resulting non-continuous zeolite film has the added advantage of a strong reduction in response times.     

Au-doped WO3-based sensor for NO2 detection at low operating temperature

Pure and Au-doped WO₃ powders for NO₂ gas detection were prepared by a colloidal chemical method, and characterized via X-ray powder diffraction (XRD), transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS). The NO₂ sensing properties of the sensors based on pure and Au-doped WO₃ powders were investigated by HW-30A gas sensing measurement. The results showed that the gas sensing properties of the doped WO₃ sensors were superior to those of the undoped one. Especially, the 1.0 wt% Au-doped WO₃ sensor possessed larger response, better selectivity, faster response/recovery and better longer term stability to NO₂ than the others at relatively low operating temperature (150 °C).     

Gas sensing properties of SnO2 nanowires on micro-heater

The SnO₂ nanowires (NWs) network gas sensors were fabricated on a micro-electrode and heater suspended in a cavity. The sensors showed selective detection to C₂H₅OH at a heater power during sensor operation as low as 30-40 mW. The gas response and response speed of the SnO₂ NWs sensor to 100 ppm C₂H₅OH were 4.6- and 4.7-fold greater, respectively, than those of the SnO₂ nanoparticles (NPs) sensor with the same electrode geometry. The reasons for these enhanced gas sensing characteristics are discussed in relation to the sensing materials and sensor structures.     

Development of SAW-based multi-gas sensor for simultaneous detection of CO2 and NO2

A 440 MHz wireless and passive surface acoustic wave (SAW)-based multi-gas sensor integrated with a temperature sensor was developed on a 41° YX LiNbO₃ piezoelectric substrate for the simultaneous detection of CO₂, NO₂, and temperature. The developed sensor was composed of a SAW reflective delay lines structured by an interdigital transducer (IDT), ten reflectors, a CO₂ sensitive film (Teflon AF 2400), and a NO₂ sensitive film (indium tin oxide). Teflon AF 2400 was used for the CO₂ sensitive film because it provides a high CO₂ solubility, with good permeability and selectivity. For the NO₂ sensitive film, indium tin oxide (ITO) was used. Coupling of mode (COM) modeling was conducted to determine the optimal device parameters prior to fabrication. Using the parameters determined by the simulation results, the device was fabricated and then wirelessly measured using a network analyzer. The measured reflective coefficient S₁₁ in the time domain showed high signal/noise (S/N) ratio, small signal attenuation, and few spurious peaks. The time positions of the reflection peaks were well matched with the predicted values from the simulation. High sensitivity and selectivity were observed at each target gas testing. The obtained sensitivity was 2.12°/ppm for CO₂ and 51.5°/ppm for NO₂, respectively. With the integrated temperature sensor, temperature compensation was also performed during gas sensitivity evaluation process.     

Solid-state potentiometric SO2 sensor combining NASICON with V2O5-doped TiO2 electrode

A compact tubular sensor based on NASICON (sodium super ionic conductor) and V₂O₅-doped TiO₂ sensing electrode was designed for the detection of SO₂. In order to reduce the size of the sensor, a thick-film of NASICON was formed on the outer surface of a small Al₂O₃ tube; furthermore, a thin layer of V₂O₅-doped TiO₂ with nanometer size was attached on the NASICON as a sensing electrode. This paper investigated the influence of V₂O₅ doping and sintering temperature on the characteristics of the sensor. The sensor attached with 5 wt% V₂O₅-doped TiO₂ sintered at 600 °C exhibited excellent sensing properties to 1–50 ppm SO₂ in air at 200–400 °C. The EMF value of the sensor was almost proportional to the logarithm of SO₂ concentration and the sensitivity (slope) was −78 mV/decade at 300 °C. It was also seen that the sensor showed a good selectivity to SO₂ against NO, NO₂, CH₄, CO, NH₃ and CO₂. Moreover, the sensor had speedy response kinetics to SO₂ too, the 90% response time to 50 ppm SO₂ was 10 s, and the recovery time was 35 s. On the basis of XPS analysis for the SO₂-adsorbed sensing electrode, a sensing mechanism involving the mixed potential at the sensing electrode was proposed.     

Nanostructured spinel ZnCo2O4 for the detection of LPG

Nanostrucutred spinel ZnCo₂O₄ (∼26-30 nm) was synthesized by calcining the mixed precursor (consisting of cobalt hydroxyl carbonate and zinc hydroxyl carbonate) in air at 600 °C for 5 h. The mixed precursor was prepared through a low cost and simple co-precipitation/digestion method. The transformation of the mixed precursor into nanostructured spinel ZnCo₂O₄ upon calcinations was confirmed by X-ray diffraction (XRD) measurement, thermogravimetric analysis (TGA), X-ray photoelectron spectroscopy (XPS) and high resolution transmission electron microscopy (HRTEM). To demonstrate the potential applicability of ZnCo₂O₄ spinel in the fabrication of gas sensors, its LPG sensing characteristics were systematically investigated. The ZnCo₂O₄ spinel exhibited outstanding gas sensing characteristics such as, higher gas response (∼72-50 ppm LPG gas at 350 °C), response time (∼85-90 s), recovery time (∼75-80 s), excellent repeatability, good selectivity and relatively lower operating temperature (∼350 °C). The experimental results demonstrated that the nanostructured spinel ZnCo₂O₄ is a very promising material for the fabrication of LPG sensors with good sensing characteristics. Plausible LPG sensing mechanism is also discussed.