Single-walled carbon nanotube network ultramicroelectrodes

Ultramicroelectrodes (UMEs) fabricated from networks of chemical vapor deposited single-walled carbon nanotubes (SWNTs) on insulating silicon oxide surfaces are shown to offer superior qualities over solid UMEs of the same size and dimensions. Disk shaped UMEs, comprising two-dimensional "metallic" networks of SWNTs, have been fabricated lithographically, with a surface coverage of <1% of the underlying insulating surface. The electrodes are long lasting and give highly reproducible responses (either for repeat runs with the same electrode or when comparing several electrodes with the same size). For redox concentrations 相似文献   

Controlled growth and characterization of two-dimensional single-walled carbon-nanotube networks for electrical applications

We demonstrate the reproducible fabrication of single-walled carbon nanotube (SWNT) networks, via catalyzed chemical vapor deposition (cCVD). Fe nanoparticles are employed as the catalyst, with methane as the carbon-containing gas. cCVD growth under these conditions results in the formation of multiply interconnected, random, two-dimensional networks of SWNTs. Investigation of the effect of parameters such as methane flow rate and temperature on the growth process enables control over the density of the network, which controls the network conductivity. Low-density networks demonstrate p-type semiconductor behavior, whilst high-density networks exhibit semimetallic behavior. In both cases conductance is demonstrated over macroscopic length scales, up to millimeters, much longer than the individual SWNTs, despite the surface coverage being <1 %. The networks can be defined in regions of a surface by photolithography before or after growth. Controlled growth of SWNT networks thus enables the application of SWNTs as macroscale conductors with controllable, predictable, and reproducible characteristics.     

Nanoscale Charge Percolation Analysis in Polymer‐Sorted (7,5) Single‐Walled Carbon Nanotube Networks

The current percolation in polymer‐sorted semiconducting (7,5) single‐walled carbon nanotube (SWNT) networks, processed from solution, is investigated using a combination of electrical field‐effect measurements, atomic force microscopy (AFM), and conductive AFM (C‐AFM) techniques. From AFM measurements, the nanotube length in the as‐processed (7,5) SWNTs network is found to range from ≈100 to ≈1500 nm, with a SWNT surface density well above the percolation threshold and a maximum surface coverage ≈58%. Analysis of the field‐effect charge transport measurements in the SWNT network using a 2D homogeneous random‐network stick‐percolation model yields an exponent coefficient for the transistors OFF currents of 16.3. This value is indicative of an almost ideal random network containing only a small concentration of metallic SWNTs. Complementary C‐AFM measurements on the other hand enable visualization of current percolation pathways in the xy plane and reveal the isotropic nature of the as‐spun (7,5) SWNT networks. This work demonstrates the tremendous potential of combining advanced scanning probe techniques with field‐effect charge transport measurements for quantification of key network parameters including current percolation, metallic nanotubes content, surface coverage, and degree of SWNT alignment. Most importantly, the proposed approach is general and applicable to other nanoscale networks, including metallic nanowires as well as hybrid nanocomposites.     

Thermal conductivity measurements of semitransparent single-walled carbon nanotube films by a bolometric technique

We introduce a new technique for measurement of the thermal conductivity of ultrathin films of single-walled carbon nanotubes (SWNTs) utilizing IR radiation as heat source and the SWNT film as thermometer. The technique is applied to study the temperature dependence of the thermal conductivity of an as-prepared SWNT film obtained in the electric arc discharge process and a film of purified SWNTs prepared by vacuum filtration. The interplay between thermal and electrical transport in SWNT networks is analyzed in relation to the type of intertube junctions and the possibility of optimizing the thermal and electrical properties of SWNT networks for specific applications is discussed.     

Reducing electrical resistance in single-walled carbon nanotube networks: effect of the location of metal contacts and low-temperature annealing

The ability to control the density of single-walled carbon nanotubes (SWNTs) during the formation of 2D networks allows one to tune the electrical properties of these thin-films from semiconductive to metallic conduction, allowing their use in numerous new materials applications. However, the resistances of such thin-films are generally non-optimal, dominated by the effects of inter-SWNT tunneling junctions, metal/SWNT contacts, sidewall defects, and the presence of residual dopants. These studies provide insight into the relative contributions of these various items to the overall resistance of an SWNT network contacted by Ti electrodes, and ways to reduce these effects via changing the structure of the metal/SWNT contact, and annealing at low temperature. Further, the addition of a mild-acid treatment was found to cause a 13-fold reduction in resistance and much greater reproducibility in inter-network conductivity.     

Methods for enhanced control over the density and electrical properties of SWNT networks

The formation of manufacturable electronic materials that incorporate single-walled carbon nanotubes (SWNTs) will most likely involve the use of networks of these molecular wires, due to the enhanced current drive and reproducibility of such films. Therefore, control over the density of SWNTs during the deposition of 2-D networks is of critical importance for the development of numerous enhanced electronic materials. Room temperature deposition methods are of particular interest as they allow separation, purification, and/or chemical modification of SWNTs before deposition. This article reports three iterative liquid-deposition techniques that allow control over the properties of three distinct types of SWNT networks. First, density control was obtained for 2-D networks of unbundled, high-aspect ratio SWNTs. Such networks exhibited semiconductive behavior, with tunable on/off ratios. Second, electrically continuous 2-D clusters of high aspect ratio SWNTs were formed by allowing capillary forces to develop in a sessile suspension droplet. These constructs displayed tunable metallic conductivity, and may have the applications as interconnects in microelectronics. Finally, highly conductive, 3-D networks of bundled SWNTs were formed via an evaporation method. For these three types of networks, the density of SWNTs, and thus the macroscopic conductance, was readily controlled via the number of deposition cycles used in their formation.     

Colored semitransparent conductive coatings consisting of monodisperse metallic single-walled carbon nanotubes

Single-walled carbon nanotubes (SWNTs) are promising materials for transparent conduction as a result of their exceptional electrical, optical, mechanical, and chemical properties. However, since current synthetic methods yield polydisperse mixtures of SWNTs, the performance of SWNT transparent conductive films has previously been hindered by semiconducting species. Here, we describe the performance of transparent conductors produced using predominantly metallic SWNTs. Compared with unsorted material, films enriched in metallic SWNTs can enhance conductivity by factors of over 5.6 in the visible and 10 in the infrared. Moreover, by using monodisperse metallic SWNTs sorted with angstrom-level resolution in diameter, semitransparent conductive coatings with tunable optical transmittance can be produced.     

Detection of a nerve agent simulant using single-walled carbon nanotube networks: dimethyl-methyl-phosphonate

Single-walled carbon nanotube (SWNT) networks were used to detect hazardous dimethyl-methyl-phosphonate (DMMP) gas in real time, employing two different metals as electrodes. Random networks of SWNTs were simply obtained by drop-casting a SWNT-containing solution onto a surface-oxidized Si substrate. Although the electrical responses to DMMP at room temperature were reversible for both metals, the Pd-contacting SWNT network sensors exhibited a higher response and a shorter response time than those of the Au-contacting SWNT network sensors at the same DMMP concentration, due to the stronger interactions between the SWNTs and Pd surface atoms. In Pd-contacting SWNT network sensors, the response increased linearly with increasing DMMP concentration and reproducible response curves were obtained for DMMP levels as low as 1 ppm. These results indicate that SWNT networks in contact with Pd electrodes can function as good DMMP sensors at room temperature with scalable and fast response and excellent recovery.     

Scanning electrochemical microscopy as a readout tool for protein electrophoresis

Scanning electrochemical microscopy (SECM) was used to image silver-stained proteins on a poly(vinylidene difluoride) membrane. The method is based on measuring the current at a scanning microelectrode in the feedback mode. The electrochemical feedback is caused by the redox-mediated etching of the isolated 5 - 10-nm-diameter silver nanoparticles formed during the staining process. Several parameters, such as the redox mediator and the staining protocol, were optimized to ensure a high resolution and a low detection limit, i.e., 0.5 ng of bovine serum albumin (4 x 10(-14) mol) distributed on an area of 1 mm(2) (4 x 10(-16) mol x cm(-2)). Images of beta-lactoglobulin A and myoglobin bands after gel electrophoretic separation and electroblotting were obtained in order to demonstrate that SECM can be employed as a sensitive and quantitative readout method for detection of proteins after gel electrophoresis. An additional advantage is that the silver staining can be removed, allowing further downstream mass spectrometry analysis.     

Design criteria for transparent single-wall carbon nanotube thin-film transistors

A study based on two-dimensional percolation theory yielding quantitative parameters for optimum connectivity of transparent single-wall carbon nanotube (SWNT) thin films is reported. Optimum SWNT concentration in the filtrated solution was found to be 0.1 mg/L with a volume of 30 mL. Such parameters lead to SWNT fractions in the films of approximately Phi = 1.8 x 10(-3), much below the metallic percolation threshold, which is found to be approximately PhiC = 5.5 x 10(-3). Therefore, the performance of transparent carbon nanotube thin-film transistors is limited by the metallic SWNTs, even below their percolation threshold. We show how this effect is related to hopping or tunneling between neighboring metallic tubes.     

Hydrothermally Oxidized Single‐Walled Carbon Nanotube Networks for High Volumetric Electrochemical Energy Storage

Improving volumetric energy density is one of the major challenges in nanostructured carbon electrodes for electrochemical energy storage device applications. Herein, a simple hydrothermal oxidation process of single‐walled carbon nanotube (SWNT) networks in dilute nitric acid is reported, enabling simultaneous physical densification and chemical functionalization of the as‐assembled randomly‐packed SWNT films. After the hydrothermal oxidation process, the density of the SWNT films increases from 0.63 to 1.02 g cm^?3 and a considerable amount of redox‐active oxygen functional groups are introduced on the surface of the SWNTs. The functionalized SWNT films are used as positive electrodes against Li metal negative electrodes for potential Li‐ion capacitors or Li‐ion battery applications. The functionalized SWNT electrodes deliver high volumetric as well as gravimetric capacities, 154 Ah L^?1 and 152 mAh g^?1, respectively, owing to the surface redox reactions between the introduced oxygen functional groups and Li ions. In addition, these electrodes exhibit a remarkable rate‐capability by retaining its high capacity of 94 Ah L^?1 (92 mAh g^?1) at a high discharge rate of 10 A g^?1. These results demonstrate the simple hydrothermal oxidation process as an attractive strategy for improving the volumetric performance of nanostructured carbon electrodes.     

Scanning electrochemical microscopy monitoring in microcantilever platforms

The deflection of cantilever systems may be performed by an indirect electrochemical method that consists of measuring the local cantilever activity and deflection in a feedback generation-collection configuration of the SECM. This is illustrated during the electrochemically assisted adsorption of Br onto a gold-coated cantilever, either in its pristine state or previously coated with a thin organic barrier. It is further extended to the adsorption of an antibody in a heterogeneous immunoassay at an allergen-coated microcantilever platform. In both reactions, the cantilever deflection is qualitatively detected from the SECM tip current measurement and a quantitative estimate is obtained through modeling. This electroanalytical strategy provides an alternative approach to standard optical detection. It can overcome some limitations of the optical method by allowing electrochemical characterization of nonconductive cantilevers and appropriate use for closed systems.     

The effects of CNT alignment on electrical conductivity and mechanical properties of SWNT/epoxy nanocomposites

The single-walled carbon nanotubes (SWNTs) filled nanocomposite SWNT/epoxy resin composite with good uniformity, dispersion and alignment of SWNTs and with different SWNTs concentrations was produced by solution casting technique. Subsequently, the semidried mixture was stretched repeatedly along one direction at a large draw-ratio of 50 for 100 times at ambient atmosphere manually to achieve a good alignment and to promote dispersion of SWNTs in the composite matrix. Composite showed higher electrical conductivities and mechanical properties such as the Young’s modulus and tensile strength along the stretched direction than perpendicular to it, and the electrical property of composite rise with the increase of SWNT concentration. The percolation threshold value of electrical conductivity along the stretching direction is lower than the value perpendicular to the SWNTs orientation. In addition, the anisotropic electric and mechanical properties results, SEM micrograph and the polarized Raman spectra of the SWNT/epoxy composite reveal that SWNTs were well dispersed and aligned in the composites by the repeated stretching process.     

Selective etching of metallic single-wall carbon nanotubes with hydrogen plasma

We present Raman scattering and scanning tunnelling microscopy (STM) measurements on hydrogen plasma etched single-wall carbon nanotubes (SWNTs). Interestingly, both the STM and Raman spectroscopy show that the metallic SWNTs are dramatically altered and highly defected by the plasma treatment. In addition, structural characterizations show that metal catalysts are detached from the ends of the SWNT bundles. For semiconducting SWNTs we observe no feature of defects or etching along the nanotubes. Raman spectra in the radial breathing mode region of plasma-treated SWNT material show that most of the tubes are semiconducting. These results show that hydrogen plasma treatment favours etching of metallic nanotubes over semiconducting ones and therefore could be used to tailor the electronic properties of SWNT raw materials.     

旋涂法制备碳纳米管发电薄膜

采用多次旋涂法在玻璃衬底表面涂覆单壁碳纳米管（SWNT）悬浊液,形成均匀的SWNT薄膜,测量碳纳米管的发电特性,利用扫描电子显微镜（SEM）观测SWNT的分布情况,并用四探针电阻仪测量薄膜不同区域的方块电阻和薄膜的电流-电压（1-V）特性,结果表明,薄膜的I-V曲线线性度和重复度很高。不同浓度的氯化钠（NaCl）溶液以不同的流速流过SWNT薄膜表面,研究薄膜两端感应电势和电路中的电流变化情况。通过分析该变化情况,对SWNT发电机理作进一步阐释。     

Use of catechol as selective redox mediator in scanning electrochemical microscopy investigations

The use of catechols, and more specifically of dopamine, as a specific redox mediator for scanning electrochemical microscopy (SECM) investigations was evaluated in the challenging situation of an ultrathin layer deposited on a conductive substrate (carbon materials). Experiments show that dopamine is a well-adapted redox system for SECM in feedback mode and in unbiased conditions. Used as a redox mediator, catechol permits the investigations of modified surfaces without an electrical connection of the sample thanks to fast charge transfer kinetics but with a surface selectivity that does not exist in classical outer-sphere redox mediators. The interest of catechol in SECM as a sensitive redox mediator is exemplified by monitoring several modification steps of an ultrathin (<1 nm) hierarchically porous organic monolayer deposited on carbon substrates. For quantitative analysis, the SECM approach curves using dopamine could simply be characterized with an irreversible electron transfer kinetics model in a large range of pH.     

Distinction of the two phases of CuTCNQ by scanning electrochemical microscopy

The two known phases of CuTCNQ and TCNQ (TCNQ = 7,7',8,8'-tetracyanoquinodimethane) have been probed by scanning electrochemical microscopy (SECM) in the feedback mode. The first use of this technique for distinguishing differences in the electronic properties of semiconductor phases exploits the large differences in conductivity that exist between CuTCNQ and the parent TCNQ material and also between the CuTCNQ phases I and II. However, the packing density of the individual CuTCNQ crystals in a film structure also is shown to influence the SECM feedback response. Finally, it is shown that films of pure phase II material or mixtures of the phases can be mapped using feedback mode SECM. The SECM method provides valuable insights for elucidating properties of semiconducting solids that are mounted on insulating substrates.     

Growth of single-walled carbon nanotube arrays from samarium on substrates

In this letter, it is reported for the first time that samarium is an effective catalyst for single-walled carbon nanotubes(SWNTs) growth via a chemical vapor deposition(CVD) process. Horizontally superlong well-oriented SWNT arrays can be generated under suitable conditions by using ethanol as carbon source. The single-wall structure was characterized by scanning electron microscopy, Raman spectroscopy and atomic force microscopy. The results show that the SWNTs from samarium have better conductivity and better structural uniformity with less defects. This rare earth metal element provides not only an alternative catalyst for SWNTs growth but also a possible way to generate high percentage of superlong semiconducting SWNT arrays for various applications of nanoelectronic device.     

Employing Raman spectroscopy to qualitatively evaluate the purity of carbon single-wall nanotube materials

Carbon single-wall nanotubes (SWNTs) have highly unique electronic, mechanical and adsorption properties, making them interesting for a variety of applications. Raman spectroscopy has been demonstrated to be one of the most important methods for characterizing SWNTs. For example, Raman spectroscopy may be employed to differentiate between metallic and semi-conducting nanotubes, and may also be employed to determine SWNT diameters and even the nanotube chirality. Single-wall carbon nanotubes are generated in a variety of ways, including arc-discharge, laser vaporization and various chemical vapor deposition (CVD) techniques. In all of these methods, a metal catalyst must be employed to observe SWNT formation. Also, all of the current synthesis techniques generate various non-nanotube carbon impurities, including amorphous carbon, fullerenes, multi-wall nanotubes (MWNTs) and nano-crystalline graphite, as well as larger micro-sized particles of graphite. For any of the potential nanotube applications to be realized, it is, therefore, necessary that purification techniques resulting in the recovery of predominantly SWNTs at high-yields be developed. It is, of course, equally important that a method for determining nanotube wt.% purity levels be developed and standardized. Moreover, a rapid method for qualitatively measuring nanotube purity could facilitate many laboratory research efforts. This review article discusses the application of Raman spectroscopy to rapidly determine if large quantities of carbon impurities are present in nanotube materials. Raman spectra of crude SWNT materials reveal tangential bands between 1500-1600 cm(-1), as well as a broad band at approximately 1350 cm(-1), attributed to a convolution of the disorder-induced band (D-band) of carbon impurities and the D-band of the SWNTs themselves. Since the full-width-at-half-maximum (FWHM) intensity of the various carbon impurity D-bands is generally much broader than that of the nanotube D-band, an indication of the SWNT purity level may be obtained by simply examining the line-width of the D-band. We also briefly discuss the effect of nanotube bundling on SWNT Raman spectra. Finally, sections on employing Raman spectroscopy, and Raman spectroscopy coupled with additional techniques, to identify the separation and possible isolation of a specific nanotube within purified SWNT materials is provided. Every SWNT can be considered to be a unique molecule, with different physical properties, depending on its (n, m) indices. The production of phase-pure (n, m) SWNTs may be essential for some nanotube applications.