水—碳钢热管的壁温控制与应用

本文分析了水－碳钢热管壁面温度调节与控制的原理。结合应用实例说明了由水－碳钢热管组成的热管换热器可以方便地调节冷热侧的换热面积以控制壁温，既适用于来流烟气温度较高的场合，又能控制换热器尾部壁温，有效地解决酸露点腐蚀的问题。     

热管式吸热器单元热管传热的数值模拟分析

热管式吸热器的热性能分析对吸热器设计有着重要意义，但由于其相变过程与热管传热的耦合作用十分复杂，至今仍是很少有人深入研究的领域。本文基于焓法建立单元热管耦合传热的物理和数学模型，模拟计算了热管壁温、蓄热容器壁温、循环工质出口温度及相变材料熔化率等参数，并与基本型吸热器进行比较，验证了热管吸热器明显改善了温度分布的均匀性和相变材料的熔化率。     

螺旋翅片管热管技术在锅炉及冶金、环保等余热回收设备上的应用

本文从实例出发论述了螺旋翅片管结构紧凑、金属耗量低、运行费用省,不易积灰等具体情况。并说明了螺旋翅片管热管用于气-气换热器的优点。导出了螺旋翅片管热管基管壁温的计算公式,指出了在设计时控制螺旋翅片管热管壁温的方法。并说明了这种技术用于锅炉、冶金及环保等余热回收设备时对抗腐蚀、防堵灰及换热效果好等情况。     

热管换热器的防腐蚀调壁温设计

热管换热器经过调壁温设计计算后，可提高受热面管壁温度，防止低温腐蚀。讨论了热管结构参数对壁温的影响，为热管换热器的防止低温腐蚀设计提供了合理的调节参数。     

热管空气预热器应用研究

热管空气预热器是一种重要的余热回收装置。它可以有效减轻锅炉的低温腐蚀,降低排烟温度,提高锅炉效率。针对某电厂锅炉热管空气预热器,进行了壁温等参数测试。结果表明,该炉加装前置式热管预热器后,排烟损失降低1.41%,锅炉效率提高1.24%。从热管空气预热器的传热特性、阻力特性、等温特性、管壁温度特性及漏风情况看,热管的设计、热管的制造和热管的安装都是成功的。     

开式热管传热特性的实验研究

对新型换热元件开式热管的传热特怀进行了实验研究，结果表明开式热管存在两个传热转折点。其实际工作的最佳范围应在两个传热转折点之间。本文给工度经、小孔直径及小孔位置变化工式热管传热能力的实验结果。为合理设计开式热管理提供了参考实验数据。     

单回路紫铜_水脉动热管传热性能的实验研究

实验研究了单回路紫铜—水脉动热管在水冷方式和定传热功率时,冷却水流量、倾角、管径和充液率4种因素对热管传热性能,包括管壁测点温度、冷热段均温、传热温差、传热热阻和温度振幅的影响规律,得到提高传热性能的一些措施。结果显示:水平放置的单回路脉动热管无法启动;30°以上倾角管内可产生振荡,增加倾角可降低传热热阻;定加热功率下,冷却水流量存在最佳值,过大和过小都会增加传热热阻;在脉动热管允许管径范围内,增加管径可大大降低传热热阻;相同传热功率时,30%充液率热管的传热热阻明显低于70%充液率管;小而均匀的壁温振荡比大幅锯齿状振荡时的传热性能好。     

开放式热管中温太阳能空气集热装置的试验研究

设计一种使用简化CPC(非追踪式复合抛物线聚光板)集热板和新型开放式热管组合的全真空玻璃集热管中温太阳能空气集热装置。每个集热单元包括一个简化CPC集热板,一根全真空玻璃集热管,在玻璃集热管内安装一个铜管和外部的一个蒸汽包连接构成一个开放式热管结构。蒸汽包内安装螺旋换热管加热通过换热管的流动空气工质。分别使用水和CuO纳米流体作为热管工质,以空气作为集热工质,对热管式中温空气集热器的传热特性进行了实验研究。分析了不同工作压力、不同工质及纳米流体质量分数对热管集热传热特性的影响,详细比较了热管水工质和纳米流体工质在集热传热性能上的优劣。试验结果表明:本系统只使用2根玻璃集热管构成集热器,空气最大出口温度在夏天可达到200℃,在冬天可接近160℃,系统平均集热效率达到0.4以上,整个系统表现了良好的中温集热特性。以纳米流体为工质的热管热阻比以水为工质时平均降低了20%左右     

某系统散热器用热管传热性能试验研究

针对某工程使用的热管散热器传热性能的影响因素进行了分析,发现充液量是决定热管散热器换热性能的关键所在。为此,对Nusselt(努塞尔特)竖壁膜状冷凝理论解进行了修正和补充,从而得出适合工程应用的理论计算式。依据此式计算出某地铁牵引系统热管散热器的理论充液量应为2.85 g,再按国家标准规定的热管传热性能试验方法对不同充液量的热管进行研究,得出了额定功率下散热器热阻随充液量变化的规律。经分析认为,散热器的最佳充液量为3g,该结果经试验证明与理论计算一致。同时通过对该充液量热管进行传热极限试验,证明3 g的充液量不仅具有适当的设计余量,还可以保证地铁系统出现过载工况时系统的运行可靠。     

换热管内转子强化换热的数值模拟

本文概述了转子组合式强化传热装置的强化传热和自清洁原理。分别通过建立光管及内置多个转子换热管的三维流动模型,对换热管内流场、温度场、压力场以及换热过程进行了模拟,得到了管内流体的流动特性和传热特性。对比模拟结果表明,内置转子换热管管内的三维流动比较复杂,转子与管壁之间缝隙内的流体有着明显的环绕流动,切向速度和径向速度也增大到一定范围,转子旋转半径内的流体整体呈螺旋流动。总的来说,内置转子的换热管内较光管有较强的湍流度,尤其是近壁区域,因此强化了管内的对流换热,传热系数显著提高,从而验证了转子具有强化传热和自清洁的双重功能。     

余热回收用热管及热管式换热器的研究

简要介绍了热管及热管式换热器的工作原理,热管式换热器在工业余热回收中的应用,以及热管式换热器运行过程中防止积灰和低温腐蚀等问题的有效措施。     

On the steady‐state modelling of a two‐stage evaporator system

We develop and validate against experimental measurements a steady‐state two‐stage flooded refrigerant evaporator model for a heat pump drying system. A prototype two‐stage heat pump dryer test facility was designed, built and instrumented to provide the required measurements for the validation of the model. Repeatability and data quality tests were conducted to evaluate the accuracy of measurements. Experimental data could be reproduced to within ±6.5 per cent of replicated air and refrigerant side measurements for the same evaporator's air inlet conditions while the discrepancy of energy balance at the air‐side and refrigerant‐side was observed to be within ±8.9 per cent. The two‐stage evaporator model predicted the air‐side total heat and latent heat transfer of the two‐stage evaporator to within (?6.3 per cent, 7.6 per cent) and (?11.5 per cent, 9.5 per cent), respectively. On the refrigerant‐side, the model enabled the calculation of the degree of superheat to within (?10.6 per cent, 1.7 per cent). The model has shown that there is significant improvement in the heat recovered from a two‐stage evaporator system compared to a single evaporator system. In addition, the model demonstrated that the improvement in total heat recovery could be as high as 40 per cent over its base‐value when the latent to total load at the two‐stage evaporator is increased. Copyright © 2001 John Wiley & Sons, Ltd.     

显热储热材料的制备及性能研究

采用水泥作为材料的胶凝剂,添加热容、热导率大的物质作为骨料来制备混凝土储热材料。研究表明:当铝酸盐水泥含量为10%时,材料的抗压、抗折强度能满足工业需求;材料的比热容随温度的升高先增大,在500℃时达到最大,后随着温度的升高反而降低;材料的热导率随着石墨粉含量的增加几乎成直线上升,当石墨含量为5%时材料的热导率大于1.7W/(m·K)。     

间歇式热处理炉传热计算与分析

建立了台车式热处理炉炉膛传热数学模型和辐射换热器工作模型,分析了换热器的传热特性（空气预热温度、壁温、传热系数）随炉况的变化。结果表明,辐射换热器的传热特性随炉子的升温及保温过程变化而波动很大,因而对炉子的热工性能产生了影响。     

Quantification of the European industrial heat demand by branch and temperature level

We present the first comprehensive estimate of the final energy demand for heat in all EU28 member states for the reference year 2012, differentiated by temperature levels, comparing two different approaches. Two different calculation approaches based on different data sets yielded estimates of the total final energy demand for heat in the EU28 of 8150 PJ and 8518 PJ in 2012, respectively. Approach 1 distinguishes between three different process heat (PH) temperature levels and results in final energy demand for heat <100°C: 2077 PJ, 100–400°C: 2214 PJ and >400°C: 3859 PJ. The second approach distinguishes between low temperature space heat and hot water (<100°C: 1161 PJ) and four different PH temperature levels with a resulting energy demand of <100°C: 1027 PJ, 100–500°C: 1785 PJ, 500–1000°C: 1679 PJ and >1000°C: 2865 PJ. The high share of high‐temperature heat illustrates the limits to the potential decarbonisation of industrial thermal processes with renewable energy sources such as (non‐concentrating) solar thermal, geothermal or environmental heat. Therefore specific information on required temperature levels is of the essence. This, in turn, points out the relevance of renewable electricity and synthetic fuels based on renewable power for a significant reduction of CO₂ emissions from the industry sector in Europe. Considering current data quality, it is recommended to develop a consistent, comprehensive methodology to significantly improve the data basis on industrial heat demand. Copyright © 2015 John Wiley & Sons, Ltd.     

Heat pump dryer Part 1: Simulation of the models

Heat pump dryer is a complex system because of the interaction of heat and mass transfer of the working fluids. Since the system cannot be completely close, ambient conditions (temperature and humidity) influence the performance of the system. To investigate the performance of the heat pump dryer thoroughly, simulation models of heat pump dryer components have been developed. The finite-difference method was employed in the simulation to examine the state of the working fluids and heat and mass transfer. The simulation of each component can be used to construct different system configurations the results of which are reported in Part 2.     

国内分离式热管概况与热环研究的小结及展望

本文对我国分离式热管技术的研究进行了简要概况,针对工程中热源在上,冷源在下及冷热源相距较远时的热量传递问题,在分析了一般分离式热管及“水回路”等技术的基础上,对一种新型分离式热管－泵或风机驱动的动力型分离式热管（简称热环）的研究进行了小结和展望。     

Field test of a novel combined system of a high-efficiency heating/cooling heat pump and a clathrate cool storage unit

The Research Laboratory of Kyushu Electric Power Co., Inc. (KEPCO) installed a novel system in March 1992 which is a combination of a super heat pump with about twice the performance of a conventional one and a compact chemical storage-type clathrate cool storage unit. A field test was implemented by integrating these units into an actual air-conditioning system. As a result of the test, system performance was determined and the effectiveness of the system was confirmed. © 1998 Scripta Technica. Heat Trans Jpn Res, 26(6): 410–418, 1997     

Heat-spreading analysis of a heat sink base embedded with a heat pipe

A simplified model predicting the heat transfer performance of a heat sink base with a high thermal conductivity was developed. Numerical analysis was performed using the commercial software FLUENT. The investigation indicates that for heat sink bases with a high effective thermal conductivity, such as the base embedded with a typical heat pipe, the entire heat sink can be modeled as a flat plate with a uniform temperature and an effective convection heat transfer coefficient. This simplified model can be used to determine the heat transfer performance of a heat sink embedded with a typical heat pipe or vapor chamber.     

Augmentation of heat transfer through passive techniques

The thermal performance of energy preservation systems is greatly improved by increasing miniaturization and boosting. These are imaginative (or Promethean) techniques to enhance heat transfer. Enhancement methods of heat transfer draw great attention in front of the industrial sector because of their ability to provide energy savings and raise the economic efficiency of thermal systems. Three techniques these methods are categorized; those are active, passive, and compound. Different types of components are used in passive methods because of the transfer/working fluid flow path to the enhancement of the heat transfer rate. In this article, the subject of the review was the passive heat transfer enhancement methods including inserts (conical strips, winglets, twisted tapes, baffles), porous materials, coil/helical/spiral tubes, rough surfaces (corrugated/ribbed surfaces), extended surfaces (fins) and nanofluids (mono and hybrid nanofluid). Recent passive heat transfer enhancement techniques are studied in this article as they are cost-effective and reliable, and also comparably passive methods do not need any extra power to promote the energy conversion systems' thermal efficiency than active methods. In the passive approaches, various components are applied to the heat transfer/working fluid flow path to improve the heat transfer rate. The passive heat transfer enhancement methods studied in this article include inserts (twisted tapes, conical strips, baffles, winglets), extended surfaces (fins), porous materials, coil/helical/spiral tubes, rough surfaces (corrugated/ribbed surfaces), and nanofluids (mono and hybrid nanofluid). From the pioneers' research work, it is clear that a lower twist ratio and lower pitch, lesser winglet angles can provide more heat transfer rate and a little bit more friction factor. In the case of nanofluids, a little bit of pumping power is enhanced. Finally, heat transfer enhancement is compared with the thermal performance factor, which is more than unity.