Impact of the Solvation State of Lead Iodide on Its Two‐Step Conversion to MAPbI3: An In Situ Investigation

Producing high efficiency solar cells without high‐temperature processing or use of additives still remains a challenge with the two‐step process. Here, the solution processing of MAPbI₃ from PbI₂ films in N,N‐dimethylformamide (DMF) is investigated. In‐situ grazing incidence wide‐angle X‐ray scattering (GIWAXS) measurements reveal a sol–gel process involving three PbI₂‐DMF solvate complexes—disordered (P₀) and ordered (P₁, P₂)—prior to PbI₂ formation. When the appropriate solvated state of PbI₂ is exposed to MAI (methylammonium Iodide), it can lead to rapid and complete room temperature conversion into MAPbI₃ with higher quality films and improved solar cell performance. Complementary in‐situ optical reflectance, absorbance, and quartz crystal microbalance with dissipation (QCM‐D) measurements show that dry PbI₂ can take up only one third of the MAI taken up by the solvated‐crystalline P₂ phase of PbI₂, requiring additional annealing and yet still underperforming. The perovskite solar cells fabricated from the ordered P₂ precursor show higher power conversion efficiency (PCE) and reproducibility than devices fabricated from other cases. The average PCE of the solar cells is greatly improved from 13.2(±0.53)% (from annealed PbI₂) to 15.7(±0.35)% (from P₂) reaching up to 16.2%. This work demonstrates the importance of controlling the solvation of PbI₂ as an effective strategy for the growth of high‐quality perovskite films and their application in high efficiency and reproducible solar cells.     

HPbI3: A New Precursor Compound for Highly Efficient Solution‐Processed Perovskite Solar Cells

Recently, there have been extensive research efforts on developing high performance organolead halide based perovskite solar cells. While most studies focused on optimizing the deposition processes of the perovskite films, the selection of the precursors has been rather limited to the lead halide/methylammonium (or formamidium) halide combination. In this work, we developed a new precursor, HPbI₃, to replace lead halide. The new precursor enables formation of highly uniform formamidium lead iodide (FAPbI₃) films through a one‐step spin‐coating process. Furthermore, the FAPbI₃ perovskite films exhibit a highly crystalline phase with strong (110) preferred orientation and excellent thermal stability. The planar heterojunction solar cells based on these perovskite films exhibit an average efficiency of 15.4% and champion efficiency of 17.5% under AM 1.5 G illumination. By comparing the morphology and formation process of the perovskite films fabricated from the formamidium iodide (FAI)/HPbI₃, FAI/PbI₂, and FAI/PbI₂ with HI additive precursor combinations, it is shown that the superior property of the HPbI₃ based perovskite films may originate from 1) a slow crystallization process involving exchange of H⁺ and FA⁺ ions in the PbI₆ octahedral framework and 2) elimination of water in the precursor solution state.     

Combination of Hybrid CVD and Cation Exchange for Upscaling Cs‐Substituted Mixed Cation Perovskite Solar Cells with High Efficiency and Stability

Mixed cation hybrid perovskites such as Cs_xFA_1?xPbI₃ are promising materials for solar cell applications, due to their excellent photoelectronic properties and improved stability. Although power conversion efficiencies (PCEs) as high as 18.16% have been reported, devices are mostly processed by the anti‐solvent method, which is difficult for further scaling‐up. Here, a method to fabricate Cs_xFA_1?xPbI₃ by performing Cs cation exchange on hybrid chemical vapor deposition grown FAPbI₃ with the Cs⁺ ratio adjustable from 0 to 24% is reported. The champion perovskite module based on Cs_0.07FA_0.93PbI₃ with an active area of 12.0 cm² shows a module PCE of 14.6% and PCE loss/area of 0.17% cm^?2, demonstrating the significant advantage of this method toward scaling‐up. This in‐depth study shows that when the perovskite films prepared by this method contain 6.6% Cs⁺ in bulk and 15.0% at the surface, that is, Cs_0.07FA_0.93PbI₃, solar cell devices show not only significantly increased PCEs but also substantially improved stability, due to favorable energy level alignment with TiO₂ electron transport layer and spiro‐MeOTAD hole transport layer, increased grain size, and improved perovskite phase stability.     

The Role of Chlorine in the Formation Process of “CH3NH3PbI3‐xClx” Perovskite

CH₃NH₃PbI_3‐xCl_x is a commonly used chemical formula to represent the methylammonium lead halide perovskite fabricated from mixed chlorine‐ and iodine‐containing salt precursors. Despite the rapid progress in improving its photovoltaic efficiency, fundamental questions remain regarding the atomic ratio of Cl in the perovskite as well as the reaction mechanism that leads to its formation and crystallization. In this work we investigated these questions through a combination of chemical, morphological, structural and thermal characterizations. The elemental analyses reveal unambiguously the negligible amount of Cl atoms in the CH₃NH₃PbI_3‐xCl_x perovskite. By studying the thermal characteristics of methylammonium halides as well as the annealing process in a polymer/perovskite/FTO glass structure, we show that the formation of the CH₃NH₃PbI_3‐xCl_x perovskite is likely driven by release of gaseous CH₃NH₃Cl (or other organic chlorides) through an intermediate organometal mixed halide phase. Furthermore, the comparative study on CH₃NH₃I/PbCl₂ and CH₃NH₃I/PbI₂ precursor combinations with different molar ratios suggest that the initial introduction of a CH₃NH₃⁺ rich environment is critical to slow down the perovskite formation process and thus improve the growth of the crystal domains during annealing; accordingly, the function of Cl^? is to facilitate the release of excess CH₃NH₃⁺ at a relatively low annealing temperatures.     

Stable α‐CsPbI3 Perovskite Nanowire Arrays with Preferential Crystallographic Orientation for Highly Sensitive Photodetectors

All‐inorganic metal‐halide perovskites CsPbX₃ (X = Cl, Br, I) exhibit higher stability than their organic–inorganic hybrid counterparts, but the thermodynamically instable perovskite α phase at room temperature of CsPbI₃ restricts the practical optoelectronic applications. Although the stabilization of α‐CsPbI₃ polycrystalline thin films is extensively studied, the creation of highly crystalline micro/nanostructures of α‐CsPbI₃ with large grain size and suppressed grain boundary remains challenging, which impedes the implementations of α‐CsPbI₃ for lateral devices, such as photoconductor‐type photodetectors. In this work, stable α‐CsPbI₃ perovskite nanowire arrays are demonstrated with large grain size, high crystallinity, regulated alignment, and position by controlling the dewetting dynamics of precursor solution on an asymmetric‐wettability topographical template. The correlation between the higher photoluminescence (PL) intensity and longer PL lifetime indicates the nanowires exhibit stable α phase and suppressed trap density. The preferential (100) orientation is characterized by discrete diffraction spots in grazing incidence wide‐angle scattering patterns, suggesting the long‐range crystallographic order of these nanowires. Based on these high‐quality nanowire arrays, highly sensitive photodetectors are realized with a responsivity of 1294 A W^?1 and long‐term stability with 90% performance retention after 30‐day ambient storage.     

Electron‐Transport‐Layer‐Assisted Crystallization of Perovskite Films for High‐Efficiency Planar Heterojunction Solar Cells

Crystal engineering of CH₃NH₃PbI₃ perovskite materials through template‐directed nucleation and growth on PbI₂ nuclei dispersed in a polar fullerene (C₆₀ pyrrolidine tris‐acid, CPTA) electron transport layer (ETL) (CPTA:PbI₂) is proposed as a route for controlling crystallization kinetics and grain sizes. Chemical analysis of the CPTA:PbI₂ template confirms that CPTA carboxylic acid groups can form a monodentate or bidentate chelate with Pb(II), resulting in a lower nucleation barrier that promotes rapid formation of the tetragonal perovskite phase. Moreover, it is demonstrated that a uniform CH₃NH₃PbI₃ film with highly crystalline and large domain sizes can be realized by increasing the spacing between nuclei to retard perovskite crystal growth via careful control of the preferred nucleation site distribution in the CPTA:PbI₂ layer. The improved perovskite morphology possesses a long photoluminescence lifetime and efficient photocarrier transport/separation properties to eliminate the hysteresis effect. The corresponding planar heterojunction photovoltaic yields a high power conversion efficiency (PCE) of 20.20%, with a high fill factor (FF) of 81.13%. The average PCE and FF values for 30 devices are 19.03% ± 0.57% and 78.67% ± 2.13%, respectively. The results indicate that this ETL template‐assisted crystallization strategy can be applied to other organometal halide perovskite‐based systems.     

Air‐Stable Highly Crystalline Formamidinium Perovskite 1D Structures for Ultrasensitive Photodetectors

State‐of‐the‐art optoelectronic devices based on metal‐halide perovskites demand solution‐processed structures with high crystallinity, controlled crystallographic orientation, and enhanced environmental stability. Formamidinium lead iodide (α‐FAPbI₃) possesses a suitable bandgap of 1.48 eV and enhanced thermal stability, whereas perovskite‐type polymorph (α‐phase) is thermodynamically instable at ambient temperatures. Stable α‐FAPbI₃ perovskite 1D structure arrays with high crystallinity and ordered crystallographic orientation are developed by controlled nucleation and growth in capillary bridges. By surface functionalization with phenylethylammonium ions (PEA⁺), FAPbI₃ wires sustain a stable α‐phase after 28 day storage in the ambient environment with a relative humidity of 50%. Enhanced photoluminescence (PL) intensity and elongated PL lifetime demonstrate suppressed trap density and high crystallinity in these 1D structures, which is also reflected by the enhanced diffraction density and pure (001) crystallographic orientation in the grazing‐incidence wide‐angle X‐ray scattering (GIWAXS) pattern. Based on these high‐quality 1D structures, sensitive photodetectors are achieved with average responsivities of 5282 A W^?1, average specific detectivities of more than 1.45 × 10¹⁴ Jones, and a fast response speed with a 3 dB bandwidth of 15 kHz.     

Precursor Solution Annealing Forms Cubic‐Phase Perovskite and Improves Humidity Resistance of Solar Cells

Solar cells with light‐absorbing layers comprising organometal halide perovskites have recently exceeded 22% efficiency. Despite high power‐conversion efficiencies, the stability of these devices, particularly when exposed to humidity and oxygen, remains poor. In the current study, a pathway to increase the stability of methylammonium lead iodide (CH₃NH₃PbI₃) based solar cells towards humidity is demonstrated, while maintaining the simplicity and solution‐processability of the active layers. Thermal annealing of the precursor solution prior to deposition induces the formation of cubic‐phase perovskite films in the solid state at room temperature. The experiments demonstrate that this improved ambient stability is correlated with the presence of the cubic phase at device operating temperatures, with the cubic phase resisting the formation of perovskite monohydrate—a pathway of degradation in conventionally processed perovskite thin films—on exposure to humidity.     

Boosting Photovoltaic Performance for Lead Halide Perovskites Solar Cells with BF4− Anion Substitutions

Composition engineering is a particularly simple and effective approach especially using mixed cations and halide anions to optimize the morphology, crystallinity, and light absorption of perovskite films. However, there are very few reports on the use of anion substitutions to develop uniform and highly crystalline perovskite films with large grain size and reduced defects. Here, the first report of employing tetrafluoroborate (BF₄^?) anion substitutions to improve the properties of (FA = formamidinium, MA = methylammonium (FAPbI₃)_0.83(MAPbBr₃)_0.17) perovskite films is demonstrated. The BF₄^? can be successfully incorporated into a mixed‐ion perovskite crystal frame, leading to lattice relaxation and a longer photoluminescence lifetime, higher recombination resistance, and 1–2 orders magnitude lower trap density in prepared perovskite films and derived solar cells. These advantages benefit the performance of perovskite solar cells (PVSCs), resulting in an improved power conversion efficiency (PCE) of 20.16% from 17.55% due to enhanced open‐circuit voltage (V_OC) and fill factor. This is the highest PCE for BF₄^? anion substituted lead halide PVSCs reported to date. This work provides insight for further exploration of anion substitutions in perovskites to enhance the performance of PVSCs and other optoelectronic devices.     

Synergistic Effect of PbI2 Passivation and Chlorine Inclusion Yielding High Open‐Circuit Voltage Exceeding 1.15 V in Both Mesoscopic and Inverted Planar CH3NH3PbI3(Cl)‐Based Perovskite Solar Cells

Enhancing open‐circuit voltage in CH₃NH₃PbI₃(Cl) perovskite solar cells has become a major challenge for approaching the theoretical limit of the power conversion efficiency. Here, for the first time, it is demonstrated that the synergistic effect of PbI₂ passivation and chlorine incorporation via controlling the molar ratio of PbI₂, PbCl₂ (or MACl), and MAI in the precursor solutions, boosts the open‐circuit voltage of CH₃NH₃PbI₃(Cl) perovskite solar cells over 1.15 V in both mesoscopic and inverted planar perovskite solar cells. Such high open‐circuit voltage can be attributed to the enhanced photoluminescence emission and carrier lifetime associated with the reduced trap densities. The morphology and composition analysis using scanning electron microscopy, X‐ray diffraction measurements, and energy dispersive X‐ray spectroscopy confirm the high quality of the optimized CH₃NH₃PbI₃(Cl) perovskite film. On this basis, record‐high efficiencies of 16.6% for nonmetal‐electrode all‐solution‐processed perovskite solar cells and 18.4% for inverted planar perovskite solar cells are achieved.     

FAPbI3‐Based Perovskite Solar Cells Employing Hexyl‐Based Ionic Liquid with an Efficiency Over 20% and Excellent Long‐Term Stability

Formamidinium lead triiodide (FAPbI₃)‐based perovskite materials are of interest for photovoltaics in view of their close‐to‐ideal bandgap, allowing absorption of photons over a broad solar spectrum. However, FAPbI₃‐based materials suffer from a notorious phase transition from the photoactive black phase (α‐FAPbI₃) to nonperovskite yellow phase (δ‐FAPbI₃) under ambient conditions. This transition dramatically reduces light absorbtion, thus, degrading the photovoltaic performance and stability of ensuring solar cells. In this study, 1‐hexyl‐3‐methylimidazolium iodide (HMII) ionic liquid (IL) is employed as an additive for the first time in FAPbI₃ perovskite to overcome the above‐mentioned issues. HMII incorporation facilitates the grain coarsening of FAPbI₃ crystal owing to its high‐polarity and high‐boiling point, which yields liquid domains between neighboring grains to reduce the activation energy of the grain‐boundary migration. As a result, the FAPbI₃ active layer exhibits micron‐sized grains with substantially suppressed parasitic traps with an Urbach energy reduced by 2 meV. Hence, the resulting perovskite solar cell achieves an efficiency of 20.6% with notable increase in open circuit voltage (V_OC) of 80 mV compared with HMII‐free cells (17.1%). More importantly, the HMII‐doped FAPbI₃‐based cells show a striking enhancement in shelf‐stability under high humidity and thermal stress, retaining >80% of their initial efficiencies at 60 ± 10% relative humidity and ≈95% at 65 °C.     

NbF5: A Novel α‐Phase Stabilizer for FA‐Based Perovskite Solar Cells with High Efficiency

The HC(NH₂)₂⁺(FA⁺) is a well‐known substitute to CH₃NH₃⁺(MA⁺) for its capability to extend light utilization for improved power conversion efficiency for perovskite solar cells; unfortunately, the dark cubic phase (α‐phase) can easily transition to the yellow orthorhombic phase (δ‐phase) at room temperature, an issue that prevents its commercial application. In this report, an inorganic material (NbF₅) is developed to stabilize the desired α‐phase perovskite material by incorporating NbF₅ additive into the perovskite films. It is found that the NbF₅ additive effectively suppresses the formation of the yellow δ‐phase in the perovskite synthesis and aging process, thus enhancing the humidity and light‐soaking stability of the perovskite film. As a result, the perovskite solar cells with the NbF₅ additive exhibit improved air stability by tenfold, retaining nearly 80% of their initial efficiency after aging in air for 50 d. In addition, under full‐sun AM 1.5 G illumination of a xenon lamp without any UV‐reduction, the perovskite solar cells with the NbF₅ additive also show fivefold improved illumination stability than the control devices without NbF₅.     

A Dual‐Retarded Reaction Processed Mixed‐Cation Perovskite Layer for High‐Efficiency Solar Cells

Mixed‐cation perovskite solar cells (PSCs) have become of enormous interest because of their excellent efficiency, which is now crossing 23.7%. Their broader absorption, relatively high stability with low fabrication cost compared to conventional single phase ABX₃ perovskites (where A: organic cation; B: divalent metal ion; and X: halide anion) are key properties of mixed‐halide mixed‐cation perovskites. However, the controlling reaction rate and formation of extremely dense, textured, smooth, and large grains of perovskite layer is a crucial task in order to achieve highly efficient PSCs. Herein, a new simple dual‐retarded reaction processing (DRP) method is developed to synthesize a high‐quality mixed‐cation (FAPbI₃)_0.85(MAPbBr₃)_0.15 (where MAPbBr₃ stands for methylammonium lead bromide and FAPbI₃ stands for formamidinium lead iodide) perovskite thin film via intermediate phase and incorporation of nitrogen‐doped reduced graphene oxide (N‐rGO). The reaction rate is retarded via two steps: first the formation of intermediate phase and second the interaction of the nitrogen groups on N‐rGO with hydrogen atoms from formamidinium cations. This DRP process allows for the fabrication of PSCs with maximum conversion efficiency higher than 20.3%.     

High‐Quality Cuboid CH3NH3PbI3 Single Crystals for High Performance X‐Ray and Photon Detectors

Organic–inorganic halide hybrid perovskite materials are promising materials for X‐ray and photon detection due to their superior optoelectronic properties. Single‐crystal (SGC) perovskites have increasingly attracted attention due to their substantially low crystal defects, which contribute to improving the figures of merit of the devices. Cuboid CH₃NH₃PbI₃ SGC with the naturally favorable geometry for device fabrication is rarely reported in X‐ray and photon detection application. The concept of seed dissolution‐regrowth to improve crystal quality of cuboid CH₃NH₃PbI₃ SGC is proposed and a fundamental understanding of the nucleation and growth is provided thermodynamically. The X‐ray detector fabricated from cuboid CH₃NH₃PbI₃ SGC demonstrates the firstly reported high sensitivity of 968.9 µC^?1 Gy^?1 cm^?2 under ?1 V bias. The results also show that the favorable crystal orientation and high quality of cuboid CH₃NH₃PbI₃ leads to better responsivity and faster response speed than the more common dodecahedral CH₃NH₃PbI₃ in photodetection. Consequently, the work paves a way to synthesize high‐quality perovskite SGCs and benefits the application of MAPbI₃ SGCs with preferred crystal orientation and favorable crystal geometry for emerging device applications.     

Efficient and Ambient‐Air‐Stable Solar Cell with Highly Oriented 2D@3D Perovskites

3D organic–inorganic lead halide perovskites have shown great potential in efficient photovoltaic devices. However, the low stability of the 3D perovskite layer and random arrangement of the perovskite crystals hinder its commercialization road. Herein, a highly oriented 2D@3D ((AVA)₂PbI₄@MAPbI₃) perovskite structure combining the advantages of both 2D and 3D perovskite is fabricated through an in situ route. The highest power conversion efficiency (PCE) of 18.0% is observed from a 2D@3D perovskite solar cell (PSC), and it also shows significantly enhanced device stability under both inert (90% of initial PCE for 32 d) and ambient conditions (72% of initial PCE for 20 d) without encapsulation. The high efficiency of 18.0% and nearly twofold improvement of device stability in ambient compared with pure 3D PSCs confirm that such 2D@3D perovskite structure is an effective strategy for high performance and increasing stability and thus will enable the timely commercialization of PSCs.     

Inorganic Rubidium Cation as an Enhancer for Photovoltaic Performance and Moisture Stability of HC(NH2)2PbI3 Perovskite Solar Cells

Perovskite solar cells (PSCs) based on organic monovalent cation (methylammonium or formamidinium) have shown excellent optoelectronic properties with high efficiencies above 22%, threatening the status of silicon solar cells. However, critical issues of long‐term stability have to be solved for commercialization. The severe weakness of the state‐of‐the‐art PSCs against moisture originates mainly from the hygroscopic organic cations. Here, rubidium (Rb) is suggested as a promising candidate for an inorganic–organic mixed cation system to enhance moisture‐tolerance and photovoltaic performances of formamidinium lead iodide (FAPbI₃). Partial incorporation of Rb in FAPbI₃ tunes the tolerance factor and stabilizes the photoactive perovskite structure. Phase conversion from hexagonal yellow FAPbI₃ to trigonal black FAPbI₃ becomes favored when Rb is introduced. The authors find that the absorbance and fluorescence lifetime of 5% Rb‐incorporated FAPbI₃ (Rb_0.05FA_0.95PbI₃) are enhanced than bare FAPbI₃. Rb_0.05FA_0.95PbI₃‐based PSCs exhibit a best power conversion efficiency of 17.16%, which is much higher than that of the FAPbI₃ device (13.56%). Moreover, it is demonstrated that the Rb_0.05FA_0.95PbI₃ film shows superior stability against high humidity (85%) and the full device made with the mixed perovskite exhibits remarkable long‐term stability under ambient condition without encapsulation, retaining the high performance for 1000 h.     

Monitoring the Formation of a CH3NH3PbI3–xClx Perovskite during Thermal Annealing Using X‐Ray Scattering

Grazing incidence wide and small angle X‐ray scattering (GIWAXS and GISAXS) measurements have been used to study the crystallization kinetics of the organolead halide perovskite CH₃NH₃PbI_3–xCl_x during thermal annealing. In situ GIWAXS measurements recorded during annealing are used to characterize and quantify the transition from a crystalline precursor to the perovskite structure. In situ GISAXS measurements indicate an evolution of crystallite sizes during annealing, with the number of crystallites having sizes between 30 and 400 nm increasing through the annealing process. Using ex situ scanning electron microscopy, this evolution in length scales is confirmed and a concurrent increase in film surface coverage is observed, a parameter crucial for efficient solar cell performance. A series of photovoltaic devices are then fabricated in which perovskite films have been annealed for different times, and variations in device performance are explained on the basis of X‐ray scattering measurements.     

Preparation of Tortuous 3D γ‐CsPbI3 Films at Low Temperature by CaI2 as Dopant for Highly Efficient Perovskite Solar Cells

Inorganic cubic CsPbI₃ perovskite (α‐CsPbI₃) has been widely explored for perovskite solar cells (PSCs) due to its thermal stability and suitable bandgap of 1.73 eV. However, α‐CsPbI₃ usually requires high synthesis temperatures (>320 °C). Additionally, it usually undergoes phase transition to the nonperovskite structure phase (β‐CsPbI₃), which results in poor photoelectric performance in devices. In this study, it is first found that the tortuous 3D CsPbI₃ phase (γ‐CsPbI₃) can be prepared and used for PSCs by solution process without any additive at low temperature (60 °C). The γ‐CsPbI₃ exhibits suitable bandgap of 1.75 eV and favorable photoelectric properties. However, γ‐CsPbI₃ is a metastable phase and easily transforms into β‐CsPbI₃ in ambient moisture. In order to improve the stability of γ‐CsPbI₃, calcium ions (Ca²⁺) with a relatively small radius of 100 pm are used to partially substitute lead ions (119 pm). This research proves that Ca²⁺ can effectively improve the stability of the γ‐CsPbI₃ at room temperature. By optimizing the doping concentration of Ca²⁺ (CsPb_1?xCa_xI₃, x is from 0% to 2%), the Ca²⁺‐doped γ‐CsPbI₃ PSCs achieve a hysteresis‐free J–V curve and a maximum power conversion efficiency (PCE) of 9.20%.     

PbTiO3 as Electron‐Selective Layer for High‐Efficiency Perovskite Solar Cells: Enhanced Electron Extraction via Tunable Ferroelectric Polarization

PbTiO₃ (PTO) is explored as a versatile and tunable electron‐selective layer (ESL) for perovskite solar cells. To demonstrate effectiveness of PTO for electron–hole separation and charge transfer, perovskite solar cells are designed and fabricated in the laboratory with the PTO as the ESL. The cells achieve a power conversion efficiency (PCE) of ≈12.28% upon preliminary optimization. It is found that the PTO ferroelectric layer can not only increase the PCE, but also tune the photocurrent via tuning PTO's ferroelectric polarization. Moreover, to understand the physical mechanism underlying the carrier transport by the ferroelectric polarization, the electronic structure of PTO/CH₃NH₃PbI₃ heterostructure is computed using the first‐principles methods, for which the triplet state is used to simulate charge transfer in the heterostructure. It is shown that the synergistic effect of type II band alignment and the specific ferroelectric polarization direction provide the effective extraction of electrons from the light absorber, while minimize recombination of photogenerated electron–hole pairs. Overall, the ferroelectric PTO is a promising and tunable ESL for optimizing electron transport in the perovskite solar cells. The design offers a different strategy for altering direction of carrier transport in solar cells.     

δ‐CsPbI3 Intermediate Phase Growth Assisted Sequential Deposition Boosts Stable and High‐Efficiency Triple Cation Perovskite Solar Cells

Cs/FA/MA triple cation perovskite films have been well developed in the antisolvent dripping method, attributable to its outstanding photovoltaic and stability performances. However, a facile and effective strategy is still lacking for fabricating high‐quality large‐grain triple cation perovskite films via sequential deposition method a, which is one of the key technologies for high efficiency perovskite solar cells. To address this issue, a δ‐CsPbI₃ intermediate phase growth (CsPbI₃‐IPG) assisted sequential deposition method is demonstrated for the first time. The approach not only achieves incorporation of controllable cesium into (FAPbI₃)_1–x(MAPbBr₃)_x perovskite, but also enlarges the perovskite grains, manipulates the crystallization, modulates the bandgap, and improves the stability of final perovskite films. The photovoltaic performances of the devices based on these Cs/FA/MA perovskite films with various amounts of the δ‐CsPbI₃ intermediate phase are investigated systematically. Benefiting from moderate cesium incorporation and intermediate phase‐assisted grain growth, the optimized Cs/FA/MA perovskite solar cells exhibit a significantly improved power conversion efficiency and operational stability of unencapsulated devices. This facile strategy provides new insights into the compositional engineering of triple or quadruple cation perovskite materials with enlarged grains and superior stability via a sequential deposition method.