High‐Speed Organic Single‐Crystal Transistor Responding to Very High Frequency Band

Although high carrier mobility organic field‐effect transistors (OFETs) are required for high‐speed device applications, improving the carrier mobility alone does not lead to high‐speed operation. Because the cut‐off frequency is determined predominantly by the total resistance and parasitic capacitance of a transistor, it is necessary to miniaturize OFETs while reducing these factors. Depositing a dopant layer only at the metal/semiconductor interface is an effective technique to reduce the contact resistance. However, fine‐patterning techniques for a dopant layer are still challenging especially for a top‐contact solution‐processed OFET geometry because organic semiconductors are vulnerable to chemical damage by solvents. In this work, high‐resolution, damage‐free patterning of a dopant layer is developed to fabricate short‐channel OFETs with a dopant interlayer inserted at the contacts. The fabricated OFETs exhibit high mobility exceeding 10 cm² V^?1 s^?1 together with a reasonably low contact resistance, allowing for high frequency operation at 38 MHz. In addition, a diode‐connected OFET shows a rectifying capability of up to 78 MHz at an applied voltage of 5 V. This shows that an OFET can respond to the very high frequency band, which is beneficial for long‐distance wireless communication.     

Porous Organic Field‐Effect Transistors for Enhanced Chemical Sensing Performances

The thin‐film structures of chemical sensors based on conventional organic field‐effect transistors (OFETs) can limit the sensitivity of the devices toward chemical vapors, because charge carriers in OFETs are usually concentrated within a few molecular layers at the bottom of the organic semiconductor (OSC) film near the dielectric/semiconductor interface. Chemical vapor molecules have to diffuse through the OSC films before they can interact with charge carriers in the OFET conduction channel. It has been demonstrated that OFET ammonia sensors with porous OSC films can be fabricated by a simple vacuum freeze‐drying template method. The resulted devices can have ammonia sensitivity not only much higher than the pristine OFETs with thin‐film structure but also better than any previously reported OFET sensors, to the best of our knowledge. The porous OFETs show a relative sensitivity as high as 340% ppm^?1 upon exposure to 10 parts per billion (ppb) NH₃. In addition, the devices also exhibit decent selectivity and stability. This general and simple strategy can be applied to a wide range of OFET chemical sensors to improve the device sensitivity.     

Hydrocarbons‐Driven Crystallization of Polymer Semiconductors for Low‐Temperature Fabrication of High‐Performance Organic Field‐Effect Transistors

While many high‐performance polymer semiconductors are reported for organic field‐effect transistors (OFETs), most require a high‐temperature postdeposition annealing of channel semiconductors to achieve high performance. This negates the fundamental attribute of OFETs being a low‐cost alternative to conventional high‐cost silicon technologies. A facile solution process is developed through which high‐performance OFETs can be fabricated without thermal annealing. The process involves incorporation of an incompatible hydrocarbon binder or wax into the channel semiconductor composition to drive rapid phase separation and instantaneous crystallization of polymer semiconductor at room temperature. The resulting composite channel semiconductor film manifests a nano/microporous surface morphology with a continuous semiconductor nanowire network. OFET mobility of up to about 5 cm² V^?1 s^?1 and on/off ratio ≥ 10⁶ are attained. These are hitherto benchmark performance characteristics for room‐temperature, solution‐processed polymer OFETs, which are functionally useful for many impactful applications.     

Highly Sensitive Chemical‐Vapor Sensor Based on Thin‐Film Organic Field‐Effect Transistors with Benzothiadiazole‐Fused‐Tetrathiafulvalene

The synthesis of a new tetrathiafulvalene derivative with an electron‐withdrawing benzothiadiazole moiety and its use in thin‐film organic field‐effect transistors (OFETs) are reported. Compared to reported OFETs with other TTF derivatives, a high hole mobility up to 0.73 cm² V^?1 s^?1, low off‐current and high on/off ratio up to 10⁵ are demonstrated. In addition, the developed OFETs show fast responsiveness toward chemical vapors of DECP (diethyl chlorophosphate) or POCl₃ which are simulants of phosphate‐based nerve agents. In contrast to previously reported OFET‐based sensors, off‐current is used as the output signal, which increases quickly upon exposure to either DECP or POCl₃ vapors. High sensitivity is demonstrated toward DECP and POCl₃ vapors, with concentrations as low as 10 ppb being detected. These OFETs are also responsive to TNT vapor. The sensing mechanisms for the new type of OFET are discussed.     

Digital‐Inverter Amine Sensing via Synergistic Responses by n and p Organic Semiconductors

Chemiresistors and sensitive organic field‐effect transistors (OFETs) have been substantially developed as cheap, scalable, and versatile sensing platforms. While new materials are expanding OFET sensing capabilities, the device architectures have changed little. Higher order logic circuits utilizing OFETs sensitive to amine vapors are presented. The circuits depend on the synergistic responses of paired p‐ and n‐channel organic semiconductors, including a rare analyte‐induced current increase by the n‐channel semiconductor. This is the first step towards ‘intelligent sensors’ that utilize analog signal changes in sensitive OFETs to produce direct digital readouts suitable for further logic operations.     

Understanding,Optimizing, and Utilizing Nonideal Transistors Based on Organic or Organic Hybrid Semiconductors

Many advanced materials have been developed for organic field‐effect transistors (OFETs) or thin‐film transistors (TFTs) based on organic and organic hybrid materials. However, although many new OFETs exhibit superior characteristic parameters (such as high mobility), most of them show nonideal performances that have strongly limited progress in the design of molecules, the understanding of transport mechanisms, and the circuit applications of OFETs. In this review, the device physics of ideal and nonideal OFETs is discussed first to understand the factors that limit effective mobility in semiconducting channels, distort the potential distribution, or reduce the drift electric field. Then, recent advances in optimizing the material combinations, device structures, and fabrications of OFETs toward ideal transistors are discussed. Based on the good control of materials and interfaces, some new and novel concepts to utilize the nonideal properties of OFETs to build low‐power circuits and integrated sensors are also discussed.     

Polymer Dielectrics and Orthogonal Solvent Effects for High‐Performance Inkjet‐Printed Top‐Gated P‐Channel Polymer Field‐Effect Transistors

We investigated the effects of a gate dielectric and its solvent on the characteristics of top‐gated organic field‐effect transistors (OFETs). Despite the rough top surface of the inkjet‐printed active features, the charge transport in an OFET is still favorable, with no significant degradation in performance. Moreover, the characteristics of the OFETs showed a strong dependency on the gate dielectrics used and its orthogonal solvents. Poly(3‐hexylthiophene) OFETs with a poly(methyl methacrylate) dielectric showed typical p‐type OFET characteristics. The selection of gate dielectric and solvent is very important to achieve high‐performance organic electronic circuits.     

Polymer‐Based Organic Field‐Effect Transistors with Active Layers Aligned by Highly Hydrophobic Nanogrooved Surfaces

In this study, polymer‐based organic field‐effect transistors (OFETs) that exhibit alignment‐induced mobility enhancement, very small device‐to‐device variation, and high operational stability are successfully fabricated by a simple coating method of semiconductor solutions on highly hydrophobic nanogrooved surfaces. The highly hydrophobic nanogrooved surfaces (water contact angle >110°) are effective at inducing unidirectional alignment of polymer backbone structures with edge‐on orientation and are advantageous for realizing high operational stability because of their water‐repellent nature. The dewetting of the semiconductor solution is a critical problem in the thin film formation on highly hydrophobic surfaces. Dewetting during spin coating is suppressed by surrounding the hydrophobic regions with hydrophilic ones under appropriate designs. For the OFET array with an aligned terrace‐phase active layer of poly(2,5‐bis(3‐hexadecylthiophene‐2‐yl)thieno[3,2‐b]thiophene), the hole mobility in the saturation regime of 30 OFETs with channel current direction parallel to the nanogrooves is 0.513 ± 0.018 cm² V^?1 s^?1, which is approximately double that of the OFETs without nanogrooves, and the intrinsic operational stability is comparable to the operational stability of amorphous‐silicon field‐effect transistors. In other words, alignment‐induced mobility enhancement and high operational stability are successfully achieved with very small device‐to‐device variation. This coating method should be a promising means of fabricating high‐performance OFETs.     

High performance n-channel thin-film field-effect transistors based on angular-shaped naphthalene tetracarboxylic diimides

We report on the performance of organic field-effect transistors (OFETs) by using a series of angular-shaped naphthalene tetracarboxylic diimides as active layers. The fabricated OFET devices exhibit n-type semiconducting characteristics. The performance of OFETs can be substantially improved by modifying the surface of the gate dielectric chemically prior to the deposition of the organic semiconductors. An increased electron mobility of the OFETs was found owing to the improved crystallinity and enlarged grain sizes, which are attributed to the elevating substrate temperature during the semiconductor deposition. The highest mobility of 0.515 cm²/V s was achieved from a device fabricated at substrate temperature of 130 °C with octadecyltrichlorosilane (OTS) surface modification.     

一种廉价电极的并五苯场效应晶体管

采用底栅顶接触结构,研究制备了以并五苯为有源层、聚甲基丙烯酸甲酯(PMMA)为绝缘层的全有机场效应晶体管(OFET),其中绝缘层采用溶液旋涂法制备,电极采用MoO3/Al双层电极。与传统采用单一Au为电极的器件相比,采用双层电极的器件性能大幅提高,经测试,器件的迁移率达到了0.133cm2/Vs,开关电流比可以达到2.61×105。对采用MoO3修饰层提高性能的作用机理进行了详细论证。     

Organic Field‐Effect Transistors: A 3D Kinetic Monte Carlo Simulation of the Current Characteristics in Micrometer‐Sized Devices

The electrical properties of organic field‐effect transistors (OFETs) are usually characterized by applying models initially developed for inorganic‐based devices, which often implies the use of approximations that might be inappropriate for organic semiconductors. These approximations have brought limitations to the understanding of the device physics associated with organic materials. A strategy to overcome this issue is to establish straightforward connections between the macroscopic current characteristics and microscopic charge transport in OFETs. Here, a 3D kinetic Monte Carlo model is developed that goes beyond both the conventional assumption of zero channel thickness and the gradual channel approximation to simulate carrier transport and current. Using parallel computing and a new algorithm that significantly improves the evaluation of electric potential within the device, this methodology allows the simulation of micrometer‐sized OFETs. The current characteristics of representative OFET devices are well reproduced, which provides insight into the validity of the gradual channel approximation in the case of OFETs, the impact of the channel thickness, and the nature of microscopic charge transport.     

Control of Polymorphism and Morphology in Solution Sheared Organic Field‐Effect Transistors

During the last decades, small molecule organic semiconductors have been successfully used as active layer in organic field‐effect transistors (OFETs). Despite the high mobility achieved so far with organic molecules, in order to progress in the field it is crucial to find techniques to process them from solution. The device reproducibility is one of the principal weak points of organic electronics for further commercialization. To achieve a high device‐to‐device reproducibility it is essential to control the morphology and polymorphism of the active layer for OFET application. In this work, the preparation of thin films is reported based on blends of the organic semiconductor dibenzo‐tetrathiafulvalene (DB‐TTF) and polystyrene by a solution shearing technique compatible with upscaling. Here, it is demonstrated that varying the deposition parameters (i.e., speed and temperature) or the solution formulation (i.e., semiconductor/binder polymer ratio) is possible to control the film morphology and semiconductor polymorphism and, hence, the different intermolecular interactions. It is demonstrated that the control of the thermodynamics and kinetics of the crystallization process is key for the device performance optimization. Further, this is the first time that DB‐TTF thin films of the α‐polymorph are reported.     

Air Effect on the Ideality of p‐Type Organic Field‐Effect Transistors: A Double‐Edged Sword

Organic field‐effect transistors (OFETs) often deviate from ideal behaviors in air, which masks their intrinsic properties and thus significantly impedes their practical applications. A key issue of how the presence of air affects the ideality of OFETs has not yet been fully understood. It is revealed that air atmosphere may exert a double‐edged sword effect on the active semiconductor layer when determining the ideality of OFETs fabricated from p‐type crystalline organic semiconductors. Upon exposing the as‐fabricated device to air, water and oxygen mainly function as efficient p‐type dopants for the active layer in the contact regions, enhancing charge carrier injection and consequently improving device ideality. Nevertheless, as the exposure time increases, the trapping centers for the injected minority charge carriers appear in the channel region, leading to degradation of device ideality. Inspired by the double‐edged sword behavior of air, a near‐ideal OFET is achieved by ingeniously utilizing the doping/positive effect and eliminating the trapping/negative effect. The effect of air on the ideality of p‐type OFETs is clarified, which not only illuminates some common observations of OFETs in air but also offers useful guidance for the construction of high‐performance ideal OFETs.     

Effect of Donor Molecular Structure and Gate Dielectric on Charge‐Transporting Characteristics for Isoindigo‐Based Donor–Acceptor Conjugated Polymers

This study investigates the effect of the molecular structure of three different donor units, naphthalene (Np), bithiophene (BT), and thiophene–vinylene–thiophene (TVT), in isoindigo (IIG)‐based donor –acceptor conjugated polymers (PIIG‐Np, PIIG‐BT and PIIG‐TVT) on the charge carrier mobility of organic field‐effect transistors (OFETs). The charge transport properties of three different IIG‐based polymers strongly depend on donor units. PIIG–BT OFETs showed 50 times higher hole mobility (0.63 cm² V^?1 s^?1) than PIIG–TVT and PIIG–Np ones of ≈ 0.01 cm² V^?1 s^?1 with CYTOP dielectric though the BT units have less planarity than the TVT and Np units. The reasons for the different mobility in IIG‐based polymers are studied by analyzing the energy structure by absorption spectra, calculating transport levels by density functional theory, investigating the in‐ and out‐of‐plane crystallinity of thin film by grazing‐incidence wide‐angle X‐ray scattering, and extracting key transport parameters via low‐temperature measurements. By combining theoretical, optical, electrical, and structural analyses, this study finds that the large difference in OFET mobility mainly originates from the transport disorders determined by the different microcrystal structure, rather than the intrinsic transport properties in isolated chains for different polymers.     

Marangoni‐Effect‐Assisted Bar‐Coating Method for High‐Quality Organic Crystals with Compressive and Tensile Strains

Low‐cost solution‐shearing methods are highly desirable for deposition of organic semiconductor crystals over a large area. To enhance the rate of evaporation and deposition, elevated substrate temperature is commonly employed during shearing processes. However, the Marangoni flow induced by a temperature‐dependent surface‐tension gradient near the meniscus line shows negative effects on the deposited crystals and its electrical properties. In the current study, the Marangoni effect to improve the shearing process of 2,7‐dioctyl[1]benzothieno[3,2‐b ][1]benzothiophene for organic field‐effect transistor (OFET) applications is utilized and regulated. By modifying the gradient of surface tension with different combinations of solvents, the mass transport of molecules is much more favorable, which largely enhances the deposition rate, reduces organic crystal thickness, enlarges grain sizes, and improves coverage. The average and highest mobility of OFETs can be increased up to 13.7 and 16 cm² V^?1 s^?1. This method provides a simple deposition approach on a large scale, which allows to further fabricate large‐area circuits, flexible displays, or bioimplantable sensors.     

Contact Resistance in Organic Field‐Effect Transistors: Conquering the Barrier

Organic semiconductors have sparked interest as flexible, solution processable, and chemically tunable electronic materials. Improvements in charge carrier mobility put organic semiconductors in a competitive position for incorporation in a variety of (opto‐)electronic applications. One example is the organic field‐effect transistor (OFET), which is the fundamental building block of many applications based on organic semiconductors. While the semiconductor performance improvements opened up the possibilities for applying organic materials as active components in fast switching electrical devices, the ability to make good electrical contact hinders further development of deployable electronics. Additionally, inefficient contacts represent serious bottlenecks in identifying new electronic materials by inhibiting access to their intrinsic properties or providing misleading information. Recent work focused on the relationships of contact resistance with device architecture, applied voltage, metal and dielectric interfaces, has led to a steady reduction in contact resistance in OFETs. While impressive progress was made, contact resistance is still above the limits necessary to drive devices at the speed required for many active electronic components. Here, the origins of contact resistance and recent improvement in organic transistors are presented, with emphasis on the electric field and geometric considerations of charge injection in OFETs.     

In‐Situ Monitoring of the Solid‐State Microstructure Evolution of Polymer:Fullerene Blend Films Using Field‐Effect Transistors

Organic field‐effect transistors (OFETs) are used to investigate the evolution of the solid‐state microstructure of blends of poly(3‐hexylthiophene) (P3HT) and [6,6]‐phenyl C₆₁‐butyric acid methyl ester (PC₆₁BM) upon annealing. Changes in the measured field‐effect mobility of holes and electrons are shown to reveal relevant information about the phase‐segregation in this system, which are in agreement with a eutectic phase behavior. Using dual‐gate OFETs and in‐situ measurements, it is demonstrated that the spatial‐ and time‐dependence of microstructural changes in such polymer:fullerene blend films can also be probed. A percolation‐theory‐based simulation is carried out to illustrate how phase‐segregation in this system is expected to lead to a substantial decrease in the electron conductivity in an OFET channel, in qualitative agreement with experimental results.     

Planarization of Polymeric Field‐Effect Transistors: Improvement of Nanomorphology and Enhancement of Electrical Performance

The planarization of bottom‐contact organic field‐effect transistors (OFETs) resulting in dramatic improvement in the nanomorphology and an associated enhancement in charge injection and transport is reported. Planar OFETs based on regioregular poly(3‐hexylthiophene) (rr‐P3HT) are fabricated wherein the Au bottom‐contacts are recessed completely in the gate‐dielectric. Normal OFETs having a conventional bottom‐contact configuration with 50‐nm‐high contacts are used for comparison purpose. A modified solvent‐assisted drop‐casting process is utilized to form extremely thin rr‐P3HT films. This process is critical for direct visualization of the effect of planarization on the polymer morphology. Atomic force micrographs (AFM) show that in a normal OFET the step between the surface of the contacts and the gate dielectric disrupts the self‐assembly of the rr‐P3HT film, resulting in poor morphology at the contact edges. The planarization of contacts results in notable improvement of the nanomorphology of rr‐P3HT, resulting in lower resistance to charge injection. However, an improvement in field‐effect mobility is observed only at short channel lengths. AFM shows the presence of well‐ordered nanofibrils extending over short channel lengths. At longer channel lengths the presence of grain boundaries significantly minimizes the effect of improvement in contact geometry as the charge transport becomes channel‐limited.     

Self‐Assembled,Millimeter‐Sized TIPS‐Pentacene Spherulites Grown on Partially Crosslinked Polymer Gate Dielectric

Here, a highly crystalline and self‐assembled 6,13‐bis(triisopropylsilylethynyl) pentacene (TIPS‐Pentacene) thin films formed by simple spin‐coating for the fabrication of high‐performance solution‐processed organic field‐effect transistors (OFETs) are reported. Rather than using semiconducting organic small‐molecule–insulating polymer blends for an active layer of an organic transistor, TIPS‐Pentacene organic semiconductor is separately self‐assembled on partially crosslinked poly‐4‐vinylphenol:poly(melamine‐co‐formaldehyde) (PVP:PMF) gate dielectric, which results in a vertically segregated semiconductor‐dielectric film with millimeter‐sized spherulite‐crystalline morphology of TIPS‐Pentacene. The structural and electrical properties of TIPS‐Pentacene/PVP:PMF films have been studied using a combination of polarized optical microscopy, atomic force microscopy, 2D‐grazing incidence wide‐angle X‐ray scattering, and secondary ion mass spectrometry. It is finally demonstrated a high‐performance OFETs with a maximum hole mobility of 3.40 cm² V^?1 s^?1 which is, to the best of our knowledge, one of the highest mobility values for TIPS‐Pentacene OFETs fabricated using a conventional solution process. It is expected that this new deposition method would be applicable to other small molecular semiconductor–curable polymer gate dielectric systems for high‐performance organic electronic applications.     

Controlling Electron and Hole Charge Injection in Ambipolar Organic Field‐Effect Transistors by Self‐Assembled Monolayers

Controlling contact resistance in organic field‐effect transistors (OFETs) is one of the major hurdles to achieve transistor scaling and dimensional reduction. In particular in the context of ambipolar and/or light‐emitting OFETs it is a difficult challenge to obtain efficient injection of both electrons and holes from one injecting electrode such as gold since organic semiconductors have intrinsically large band gaps resulting in significant injection barrier heights for at least one type of carrier. Here, systematic control of electron and hole contact resistance in poly(9,9‐di‐n‐octylfluorene‐alt‐benzothiadiazole) ambipolar OFETs using thiol‐based self‐assembled monolayers (SAMs) is demonstrated. In contrast to common believe, it is found that for a certain SAM the injection of both electrons and holes can be improved. This simultaneous enhancement of electron and hole injection cannot be explained by SAM‐induced work‐function modifications because the surface dipole induced by the SAM on the metal surface lowers the injection barrier only for one type of carrier, but increases it for the other. These investigations reveal that other key factors also affect contact resistance, including i) interfacial tunneling through the SAM, ii) SAM‐induced modifications of interface morphology, and iii) the interface electronic structure. Of particular importance for top‐gate OFET geometry is iv) the active polymer layer thickness that dominates the electrode/polymer contact resistance. Therefore, a consistent explanation of how SAM electrode modification is able to improve both electron and hole injection in ambipolar OFETs requires considering all mentioned factors.