Synthesis and characterization of submicron-sized LiNi1/3Co1/3Mn1/3O2 by a simple self-propagating solid-state metathesis method

Submicron-sized LiNi_1/3Co_1/3Mn_1/3O₂ cathode materials were synthesized using a simple self-propagating solid-state metathesis method with the help of ball milling and the following calcination. A mixture of Li(ac)·2H₂O, Ni(ac)₂·4H₂O, Co(ac)₂·4H₂O, Mn(ac)₂·4H₂O (ac = acetate) and excess H₂C₂O₄·2H₂O was used as starting material without any solvent. XRD analyses indicate that the LiNi_1/3Co_1/3Mn_1/3O₂ materials were formed with typical hexagonal structure. The FESEM images show that the primary particle size of the LiNi_1/3Co_1/3Mn_1/3O₂ materials gradually increases from about 100 nm at 700 °C to 200–500 nm at 950 °C with increasing calcination temperature. Among the synthesized materials, the LiNi_1/3Co_1/3Mn_1/3O₂ material calcined at 900 °C exhibits excellent electrochemical performance. The steady discharge capacities of the material cycled at 1 C (160 mA g⁻¹) rate are at about 140 mAh g⁻¹ after 100 cycles in the voltage range 3–4.5 V (versus Li⁺/Li) and the capacity retention is about 87% at the 350th cycle.     

Microemulsion preparation and electrochemical characteristics of LiNi1/3Co1/3Mn1/3O2 powders

Layer-structured LiNi_1/3Co_1/3Mn_1/3O₂ was successfully synthesized via a reverse microemulsion (RμE) route. Well-crystallized nanosized (around 45 nm) powders were obtained with calcination at 800 °C. The Rietveld refinement data revealed low degree of cationic displacement in the obtained powders. Within the voltage range of 2.5–4.5 V, the microemulsion-derived LiNi_1/3Co_1/3Mn_1/3O₂ delivered 187.2 and 195.5 mAh g⁻¹ at room temperature and 55 °C, respectively. The prepared powders were found to exhibit low irreversible capacity and good capacity retention. Microemulsion-derived LiNi_1/3Co_1/3Mn_1/3O₂ demonstrated better rate capability than the solid-state derived samples, owing to the reduced particle size and increased surface area. Once the upper cut-off voltage reached 4.6 V, the capacity faded more rapidly than in other operation potential ranges. In this study, the microemulsion process effectively improved the electrochemical characteristics of LiNi_1/3Co_1/3Mn_1/3O₂. This soft chemical route possesses a great potential for synthesizing other types of cathode materials with multiple cations.     

Electrochemical performance of SrF2-coated LiNi1/3Co1/3Mn1/3O2 cathode materials for Li-ion batteries

SrF₂-coated LiNi_1/3Co_1/3Mn_1/3O₂ cathode materials with improved cycling performance over 2.5–4.6 V were investigated. The structural and electrochemical properties of the materials were studied using X-ray diffraction (XRD), scanning electron microscope (SEM), charge–discharge tests and electrochemical impedance spectra (EIS). The results showed that the crystalline SrF₂ with about 10–50 nm particle size is uniformly coated on the surface of LiNi_1/3Co_1/3Mn_1/3O₂ particles. As the coating amount increased from 0.0 to 2.0 mol%, the initial capacity and rate capability of the coated LiNi_1/3Co_1/3Mn_1/3O₂ decreased slightly owing to the increase of the charge-transfer resistance; however, the cycling stability was improved by suppressing the increase of the resistance during cycling. 4.0 mol% SrF₂-coated LiNi_1/3Co_1/3Mn_1/3O₂ showed remarkable decrease of the initial capacity. 2.0 mol% coated sample exhibited the best electrochemical performance. It presented an initial discharge capacity of 165.7 mAh g⁻¹, and a capacity retention of 86.9% after 50 cycles at 4.6 V cut-off cycling.     

Study of the surface modification of LiNi1/3Co1/3Mn1/3O2 cathode material for lithium ion battery

The surface of LiNi_1/3Co_1/3Mn_1/3O₂ (LNMCO) particles has been studied for material synthesized at 900 °C by a two-step process from a mixture of LiOH·H₂O and metal oxalate [(Ni_1/3Co_1/3Mn_1/3)C₂O₄] obtained by co-precipitation. Samples have been characterized by X-ray diffraction (XRD), high-resolution transmission electron microscope (HRTEM), Raman scattering (RS) spectroscopy, and magnetic measurements. We have investigated the effect of the heat treatment of particles at 600 °C with organic substances such as sucrose and starch. HRTEM images and RS spectra indicate that the surface of particles has been modified. The annealing does not lead to any carbon coating but it leads to the crystallization of the thin disordered layer on the surface of LiNi_1/3Co_1/3Mn_1/3O₂. The beneficial effect has been tested on the electrochemical properties of the LiNi_1/3Co_1/3Mn_1/3O₂ cathode materials. The capacity at 10C-rate is enhanced by 20% for post-treated LNMCO particles at 600 °C for half-an-hour.     

Synthesis of LiNi1/3Co1/3Mn1/3O2 as a cathode material for lithium battery by the rheological phase method

LiNi_1/3Co_1/3Mn_1/3O₂ is prepared by a rheological phase method. Homogeneous precursor derived from this method is calcined at 800 °C for 20 h in air, which results in the impressive differences in the morphology properties and electrochemical behaviors of LiNi_1/3Co_1/3Mn_1/3O₂ in contrast to that obtained by a solid-state method. The microscopic structural features of LiNi_1/3Co_1/3Mn_1/3O₂ are investigated using scanning electron microscopy (SEM), X-ray diffraction (XRD). The electrochemical properties of LiNi_1/3Co_1/3Mn_1/3O₂ are carried out by charge–discharge cycling test. All experiments show that the microscopic structural features and the morphology properties are deeply related with the electrochemical performances. The obtained results suggest that the rheological phase method may become an effective route to prepare LiNi_1/3Co_1/3Mn_1/3O₂ cathode materials for lithium battery.     

Cycle life improvement of ZrO2-coated spherical LiNi1/3Co1/3Mn1/3O2 cathode material for lithium ion batteries

A modified synthesis process was developed based on co-precipitation method followed by spray drying process. In this process, a spherical shaped (Co_1/3Ni_1/3Mn_1/3)(OH)₂ precursor was synthesized by co-precipitation and pre-heated at 500 °C to form a high structural stability spinel (CoNiMn)O₄ to maintain its shape for further processing. The spherical LiNi_1/3Co_1/3Mn_1/3O₂ was then prepared by spray drying process using spherical spinel (CoNiMn)O₄. LiNi_1/3Co_1/3Mn_1/3O₂ powders were then modified by coating their surface with a uniform and nano-sized layer of ZrO₂. The ZrO₂-coated LiNi_1/3Co_1/3Mn_1/3O₂ material exhibited an improved rate capability and cycling stability under a high cut-off voltage of 4.5 V. X-ray diffraction (XRD) measurements revealed that the material had a well-ordered layered structure and Zr was not doped into the LiNi_1/3Co_1/3Mn_1/3O₂. Electrochemical impedance spectroscopy measurements showed that the coated material has stable cell resistance regardless of cycle number. The interrupt charging/discharging test indicated that the ZrO₂ coating can suppress the polarization effects during the charging and discharging process. From these results, it is believed that the improved cycling performance of ZrO₂-coated LiNi_1/3Co_1/3Mn_1/3O₂ is attributed to the ability of ZrO₂ layer in preventing direct contact of the active material with the electrolyte resulting in a decrease of electrolyte decomposition reactions.     

In situ X-ray diffraction studies of mixed LiMn2O4-LiNi1/3Co1/3Mn1/3O2 composite cathode in Li-ion cells during charge-discharge cycling

The structural changes of the composite cathode made by mixing spinel LiMn₂O₄ and layered LiNi_1/3Co_1/3Mn_1/3O₂ in 1:1 wt% in both Li-half and Li-ion cells during charge/discharge are studied by in situ XRD. During the first charge up to ∼5.2 V vs. Li/Li⁺, the in situ XRD spectra for the composite cathode in the Li-half cell track the structural changes of each component. At the early stage of charge, the lithium extraction takes place in the LiNi_1/3Co_1/3Mn_1/3O₂ component only. When the cell voltage reaches at ∼4.0 V vs. Li/Li⁺, lithium extraction from the spinel LiMn₂O₄ component starts and becomes the major contributor for the cell capacity due to the higher rate capability of LiMn₂O₄. When the voltage passed 4.3 V, the major structural changes are from the LiNi_1/3Co_1/3Mn_1/3O₂ component, while the LiMn₂O₄ component is almost unchanged. In the Li-ion cell using a MCMB anode and a composite cathode cycled between 2.5 V and 4.2 V, the structural changes are dominated by the spinel LiMn₂O₄ component, with much less changes in the layered LiNi_1/3Co_1/3Mn_1/3O₂ component, comparing with the Li-half cell results. These results give us valuable information about the structural changes relating to the contributions of each individual component to the cell capacity at certain charge/discharge state, which are helpful in designing and optimizing the composite cathode using spinel- and layered-type materials for Li-ion battery research.     

Effect of Ag additive on the performance of LiNi1/3Co1/3Mn1/3O2 cathode material for lithium ion battery

The LiNi_1/3Co_1/3Mn_1/3O₂/Ag composite used for cathode material of lithium ion battery was prepared by thermal decomposition of AgNO₃ added to commercial LiNi_1/3Co_1/3Mn_1/3O₂ powders to improve the electrochemical performance of LiNi_1/3Mn_1/3Co_1/3O₂. Structure and morphology analysis showed that Ag particles were dispersed on the surface of LiNi_1/3Co_1/3Mn_1/3O₂ instead of entering the crystal structure. The results of charge–discharge tests showed that Ag additive could improve the cycle performance and high-rate discharge capability of LiNi_1/3Mn_1/3Co_1/3O₂. Extended analysis indicated that Ag was unstable in the commercial electrolyte at high potential. The improved electrochemical performance caused by Ag additive was associated not only with the enhancement of electrical conductivity of the material and the lower polarization of the cell, but also with the increased “c” parameter of LiNi_1/3Mn_1/3Co_1/3O₂ after repeated charge/discharge cycles and the compact and protective SEI layer formed on the surface of LiNi_1/3Mn_1/3Co_1/3O₂.     

Studies on the low-heating solid-state reaction method to synthesize LiNi1/3Co1/3Mn1/3O2 cathode materials

The low-heating solid-state method has been adopted to synthesize LiNi_1/3Co_1/3Mn_1/3O₂ materials. The final product, with homogeneous phase and smooth crystals indicated by XRD and SEM results, can be synthesized at 700 °C, much lower than the synthesis temperatures of co-precipitation method. The reaction process and microstructure of precursor has been investigated by IR spectrum. By comparative studies with the mixture of CH₃COOLi and (Ni, Co, Mn)(C₂O₄), it is testified that the precursor is homogeneous, rather than a mixture. The decomposition process and the reaction energy have been studied to investigate the reaction mechanism of the precursor when heated at high temperature. The as-synthesized LiNi_1/3Co_1/3Mn_1/3O₂ exhibits excellent electrochemical properties, exhibiting initial specific capacity of 167 mAh g⁻¹ with stable cyclic performance.     

A comparative study of electrodes comprising nanometric and submicron particles of LiNi0.50Mn0.50O2, LiNi0.33Mn0.33Co0.33O2, and LiNi0.40Mn0.40Co0.20O2 layered compounds

In this paper we compare the behavior of LiNi_0.5Mn_0.5O₂, LiNi_0.33Mn_0.33Co_0.33O₂ (NMC) and LiNi_0.4Mn_0.4Co_0.2O₂ as cathode materials for advanced rechargeable Li-ion batteries. These materials were prepared by a self-combustion reaction (SCR) from the metal nitrates and sucrose, followed by calcination at elevated temperatures. The temperature and duration of calcination enabled the adjustment of the average particle size and size distribution. It was established that the annealing temperature (700–900 °C) of the as-prepared oxides influences strongly the crystallite and particle size, the morphology of the material, and the electrochemical performance of electrodes in Li-cells. Capacities up to 190, 180 and 170 mAh g⁻¹ could be obtained with Li[NiMn]O₂, LiNi_0.4Mn_0.4Co_0.2O₂ and LiNi_0.33Mn_0.33Co_0.33O₂, respectively. In terms of rate capability, the order of these electrodes is NMC < LiNi_0.4Mn_0.4Co_0.2O₂ ? Li[NiMn]O₂. Many hundreds of cycles at full DOD could be obtained with Li[NiMn]O₂ and NMC electrodes in Li-cells, at room temperature. All of these materials develop a unique surface chemistry that leads to their passivation and stabilization in standard electrolyte solutions (alkyl carbonates/LiPF₆). The surface chemistry was studied by FTIR, XPS and Raman spectroscopy and is discussed herein.     

Preparation of spherical LiNi0.80Co0.15Mn0.05O2 lithium-ion cathode material by continuous co-precipitation

Micro-spherical Ni_0.80Co_0.15Mn_0.05(OH)₂ precursors with a narrow size-distribution and high tap-density are prepared successfully by continuous co-precipitation of the corresponding metal salt solutions using NaOH and NH₄OH as precipitation and complexing agents. LiNi_0.80Co_0.15Mn_0.05O₂ is then prepared as a lithium battery cathode from this precursor by the introduction of LiOH·H₂O. The pH and NH₃:metal molar ratio show significant effects on the morphology, microstructure and tap-density of the prepared Ni_0.80Co_0.15Mn_0.05(OH)₂ and the R values and I(0 0 3)/I(1 0 4) ratio of lithiated LiNi_0.80Co_0.15Mn_0.05O₂. Spherical LiNi_0.80Co_0.15Mn_0.05O₂ prepared under optimum conditions reveals a hexagonally ordered, layered structure without cation mixing and an initial charging capacity of 176 mAhg⁻¹. More than 91% of the capacity is retained after 40 cycles at the 1 C rate in a cut-off voltage range of 4.3-3.0 V.     

On the LiNi0.2Mn0.2Co0.6O2 positive electrode material

Layered LiNi_0.2Mn_0.2Co_0.6O₂ phase, belonging to a solid solution between LiNi_1/2Mn_1/2O₂ and LiCoO₂ most commercialized cathodes, was prepared via the combustion method at 900 °C for a short time (1 h). Structural, electrochemical and magnetic properties of this material were investigated. Rietveld analysis of the XRD pattern shows this compound as having the α-NaFeO₂ type structure (S.G. R-3m; a = 2.8399(2) ?; c = 14.165(1) ?) with almost none of the well-known Li/Ni cation disorder. SQUID measurements clearly indicate that the studied compound consists of Ni²⁺, Co³⁺ and Mn⁴⁺ ions in the crystal structure. X-ray analysis of the chemically delithiated Li_xNi_0.2Mn_0.2Co_0.6O₂ phases reveals that the rhombohedral symmetry was maintained during Li-extraction, confirmed by the monotonous variation of the potential-composition curve of the Li//Li_xNi_0.2Mn_0.2Co_0.6O₂ cell. LiNi_0.2Mn_0.2Co_0.6O₂ cathode has a discharge capacity of ∼160 mAh g⁻¹ in the voltage range 2.7-4.3 V corresponding to the extraction/insertion of 0.6 lithium ion with very low polarization. It exhibits a stable capacity on cycling and good rate capability in the rate range 0.2-2 C. The almost 2D structure of this cathode material, its good electrochemical performances and its relatively low cost comparing to LiCoO₂, make this material very promising for applications.     

Preparation and electrochemical characterization of single-crystalline spherical LiNi1/3Co1/3Mn1/3O2 powders cathode material for Li-ion batteries

LiNi_1/3Co_1/3Mn_1/3O₂ has aroused much interest as a new generation of cathode material for Li-ion batteries, due to its great advantages in capacity, stability, low cost and low toxicity, etc. Here we report a novel single-crystalline spherical LiNi_1/3Co_1/3Mn_1/3O₂ material that is prepared by a convenient rheological phase reaction route. The X-ray powder diffraction, scanning electron microscopy and transmission electron microscopy indicate that the particles are highly dispersed with spherical morphologies and diameters of about 1-4 μm, and more interestingly, they show a perfect single-crystalline nature, which is not usual according to the crystal growth theories and may bring extra benefits to applications. Electrochemical tests show good performance of the material in both the capacity and cycling stability as cathode material in a model cell.     

A modified ZrO2-coating process to improve electrochemical performance of Li(Ni1/3Co1/3Mn1/3)O2

A modified Zr-coating process was introduced to improve the electrochemical performance of Li(Ni_1/3Co_1/3Mn_1/3)O₂. The ZrO₂-coating was carried out on an intermediate, (Ni_1/3Co_1/3Mn_1/3)(OH)₂, rather than on Li(Ni_1/3Co_1/3Mn_1/3)O₂. After a heat treatment process, one part of the Zr covered the surface of Li(Ni_1/3Co_1/3Mn_1/3)O₂ in the form of a Li₂ZrO₃ coating layer, and the other part diffused into the crystal lattice of Li(Ni_1/3Co_1/3Mn_1/3)O₂. A decreasing gradient distribution in the concentration of Zr was detected from the surface to the bulk of Li(Ni_1/3Co_1/3Mn_1/3)O₂ by X-ray photoelectron spectra (XPS). Electrochemical tests indicated that the 1% (Zr/Ni + Co + Mn) ZrO₂-modified Li(Ni_1/3Co_1/3Mn_1/3)O₂ prepared by this process showed better cyclability and rate capability than bare Li(Ni_1/3Co_1/3Mn_1/3)O₂. The result can be ascribed to the special effect of Zr in ZrO₂-modified Li(Ni_1/3Co_1/3Mn_1/3)O₂. The surface coating layer of Li₂ZrO₃ improved the cycle performance, while the incorporation of Zr in the crystal lattice of Li(Ni_1/3Co_1/3Mn_1/3)O₂ modified the rate capability by increasing the lattice parameters. Electrochemical impedance spectra (EIS) results showed that the increase of charge transfer resistance during cycling was suppressed significantly by ZrO₂ modification.     

Mechanistic study on lithium intercalation using a restricted reaction field in LiNi0.5Mn0.5O2

Structure changes of LiNi_0.5Mn_0.5O₂ were detected at the electrode/electrolyte interface of lithium cell using synchrotron X-ray scattering and two-dimensional model electrodes. The electrodes were constructed by an epitaxial film of LiNi_0.5Mn_0.5O₂ synthesized by pulsed laser deposition (PLD) method. The orientation of the film depends on the substrate plane; the 2D layer of LiNi_0.5Mn_0.5O₂ is parallel to the SrTiO₃(1 1 0) substrate ((1 1 0) LiNi_0.5Mn_0.5O₂//(1 1 0) SrTiO₃), while the 2D layer is perpendicular to the SrTiO₃(1 1 1) substrate ((0 0 3) LiNi_0.5Mn_0.5O₂//(1 1 1) SrTiO₃). The in situ X-ray diffraction of LiNi_0.5Mn_0.5O₂(0 0 3) confirmed three-dimensional lithium diffusion through the two-dimensional transition meal layers. The intercalation reaction of LiNi_0.5Mn_0.5O₂ will be discussed.     

Structural and electrochemical properties of LiNi1/3Co1/3Mn1/3O2: Calcination temperature dependence

The structure of the layered LiNi_1/3Co_1/3Mn_1/3O₂ has been investigated by powder X-ray diffraction and electron diffraction, and the relationship of the calcination temperature with the crystal structure, morphology and electrochemical properties has been studied. All the unit cell parameters increase monotonically with increasing the calcination temperature. Some of the [00.1] zone electron diffraction patterns for the sample calcined at higher temperature than 1000 °C show extra spots indicating the 2 × 2 ordering in the basal triangular lattice. These results indicate that the high temperature calcination leads to the formation of vacancies in the transition metal layers with the spinel-like ordering. The calcination at higher temperature lowers the specific capacities and degrades the cycle performances, while the packing density of the powder is increased by the sintering. The optimum calcination temperature is 900 °C in order to obtain the electrochemically active and dense packed oxide particles. The decrease of Li composition leads to coprecipitation of the spinel-like second phase in the range of 0.742 ≤ x ≤ 0.884 for Li_xNi_1/3Co_1/3Mn_1/3O₂, when calcined at 900 °C. The Li-deficient samples show the worse electrochemical properties similarly to the stoichiometric samples calcined at high temperature. For the Li-excess samples, no impurity phase has been detected and their cycle performances are improved.     

Surface modification of LiNi1/2Mn3/2O4 thin-films by zirconium alkoxide/PMMA composites and their effects on electrochemical properties

Three kinds of surface modifications were carried out on LiNi_1/2Mn_3/2O₄ thin-films to improve the charge and discharge characteristics of LiNi_1/2Mn_3/2O₄ positive electrodes. Among them, Zr(OBu)₄/poly(methyl methacrylate) (PMMA)-treated LiNi_1/2Mn_3/2O₄ thin-film electrodes showed charge and discharge efficiency of 80–84% in the first cycle, which was much higher than that for an untreated LiNi_1/2Mn_3/2O₄ thin-film electrode (73%). The values of the charge and discharge efficiency were still higher than that for an untreated electrode after the 30th cycle. The charge and discharge curves gave two plateaus at around 4.72 and 4.76 V, which were very similar to those for the untreated electrode. Ac impedance spectroscopy revealed that the surface film resistance should not increase by Zr(OBu)₄/PMMA treatment. XPS measurements suggest that a composite layer should be formed on a LiNi_1/2Mn_3/2O₄ thin-film electrode from PMMA and Zr(OBu)₄-derived compounds introducing an electrolyte. This composite layer was lithium-ion conductive, and was sustainable enough to suppress subsequent decomposition of an electrolyte at potentials as high as 4.7 V.     

Thermal and electrochemical characterization of MCMB/LiNi1/3Co1/3Mn1/3O2 using LiBoB as an electrolyte additive

The gas generation associated with the use of the lithium bis(oxalate)borate—(LiBoB) based electrolyte at the elevated temperature were detected in the pouch cell (MCMB/LiNi_1/3Co_1/3Mn_1/3O₂ with 10% excess Li), which might prevent the LiBoB usage as a salt. However, the cell capacity retention was improved significantly, from 87 to 96% at elevated temperature, when using LiBoB as an electrolyte additive. The capacity fade during cycling is discussed using dQ/dE, area specific impedance, and frequency response analysis results. Most of the capacity loss in the cell is associated with the rise in the cell impedance. Moreover, results from the differential scanning calorimetry indicate that the thermal stability of the negative electrode with the solid electrolyte interface (SEI) formed by the reduction of the LiBoB additive was greatly improved compared with that obtained from the reduction of LiPF₆-based electrolyte without additive. In this case, the onset temperature of the breakdown of the LiBoB-based SEI is 150 °C which is higher than that of the conventional electrolyte without additive. Furthermore, the total heat generated between 60 and 170 °C is reduced from 213 to 70 J g⁻¹ when using LiBoB as electrolyte additive compared to the one without additive. In addition, the thermal stability of the charged LiNi_1/3Co_1/3Mn_1/3O₂ with 10% excess Li was not affected when using LiBoB as an electrolyte additive.     

Preparation and electrochemical properties of layer-structured LiNi1/3Co1/3Mn1/3−yAlyO2

Layer-structured LiNi_1/3Co_1/3Mn_1/3−yAl_yO₂ has been synthesized via a sol–gel method. The lattice constants of LiNi_1/3Co_1/3Mn_1/3−yAl_yO₂ decrease with the concentration of aluminum ions. XANES analysis further confirms that the valence of cobalt ion is 3+, and that of Ni is between 2+ and 3+ in LiNi_1/3Co_1/3Mn_1/3−yAl_yO₂. With doping aluminum ions, the redox centers for the electrochemical reaction change from nickel ions alone to both nickel and cobalt ions. The amounts of de-intercalatable lithium ions are affected by the concentration of aluminum ions; however, the extracting efficiency of lithium ions is improved by doping aluminum ions. Among all the samples, LiNi_1/3Co_1/3Mn_0.23Al_0.1O₂ exhibits the best capacity retention and the least irreversible capacity.     

Improvement of structural and electrochemical properties of AlF3-coated Li[Ni1/3Co1/3Mn1/3]O2 cathode materials on high voltage region

The particle surface of Li[Ni_1/3Co_1/3Mn_1/3]O₂ was modified by AlF₃ as a new coating material to improve the electrochemical properties in the high cutoff voltage of 4.5 V. The AlF₃-coated Li[Ni_1/3Co_1/3Mn_1/3]O₂ showed no difference in the bulk structure compared with the pristine one and the uniform AlF₃ coating layers whose thickness is of about 10 nm covered Li[Ni_1/3Co_1/3Mn_1/3]O₂ particles, as confirmed by a transmission electron microscopy. The AlF₃ coating on Li[Ni_1/3Co_1/3Mn_1/3]O₂ particles improved the overall electrochemical properties such as the cyclability, rate capability and thermal stability compared with those of the pristine Li[Ni_1/3Co_1/3Mn_1/3]O₂. Such enhancements were attributed to the presence of the stable AlF₃ layer which acts as the interfacial stabilizer on the surface of Li[Ni_1/3Co_1/3Mn_1/3]O₂.